The following document contains information on Cypress products. FUJITSU SEMICONDUCTOR SUPPORT SYSTEM SS01-71037-1E F2MC-16 Family EMULATOR LQFP-80P PROBE HEADER TYPE2 MB2147-561 OPERATION MANUAL PREFACE Thank you for purchasing the LQFP-80P probe header type2 (MB2147-561) for the F2MC-16 family emulator. The LQFP-80P probe header type2 is used to connect the F2MC-16L/16LX emulator (MB2147-01, referred to as "emulator") and the F2MC-16L/16LX emulator PGA-299P adapter board (MB214720, referred to as "adapter board") to a user system. That uses Fujitsu F2MC *1 -16LX microcontroller MB90820 series (LQFP-80P *2 ). This manual explains the handling of the LQFP-80P probe header type2 for the F2MC-16 family emulator. Before using the MB2147-561, be sure to read this manual. Consult the Sales representatives or the Support representatives of Fujitsu Limited for mass-produced MCUs and evaluation MCUs. *1 : F2MC is the abbreviation used for FUJITSU Flexible Microcontroller. *2 : The lead pitch of PACKAGE (FPT-80P-M05) is 0.5 mm and the body size is 12 mm × 12 mm.Using the product safely. ■■ Handling and use The handling and use of this product and notes regarding safety are included in the hardware manual of the F2MC-16 family emulator. Follow the instructions in "F2MC-16/16LX EMULATOR MB2147-01 HARDWARE MANUAL" and "F2MC-16/16LX EMULATOR PGA-299P ADAPTER BOARD MB2147-20 HARDWARE MANUAL" for the use of this product. ■■ Caution of the products described in this document The following precautions apply to the product described in this manual. CAUTION The wrong use of a device will give an injury and may cause malfunction on customers system. Cuts This product has parts with sharp points that are exposed. Do not touch edge of the product with your bare hands. Damage When connect the header board to the user system, correctly position the index mark (▲) on the NQPACK mounted on the user system with the index mark (▲) on the header board, otherwise the emulator system and user system might be damaged. Damage When mounting a mass production MCU, correctly position pin 1, otherwise the mass production MCU and user system might be damaged. i • The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. • The information, such as descriptions of function and application circuit examples, in this document are presented solely for the purpose of reference to show examples of operations and uses of FUJITSU semiconductor device; FUJITSU does not warrant proper operation of the device with respect to use based on such information. When you develop equipment incorporating the device based on such information, you must assume any responsibility arising out of such use of the information. FUJITSU assumes no liability for any damages whatsoever arising out of the use of the information. • Any information in this document, including descriptions of function and schematic diagrams, shall not be construed as license of the use or exercise of any intellectual property right, such as patent right or copyright, or any other right of FUJITSU or any third party or does FUJITSU warrant non-infringement of any third-party’s intellectual property right or other right by using such information. FUJITSU assumes no liability for any infringement of the intellectual property rights or other rights of third parties which would result from the use of information contained herein. • The products described in this document are designed, developed and manufactured as contemplated for general use, including without limitation, ordinary industrial use, general office use, personal use, and household use, but are not designed, developed and manufactured as contemplated (1) for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could have a serious effect to the public, and could lead directly to death, personal injury, severe physical damage or other loss (i.e., nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system), or (2) for use requiring extremely high reliability (i.e., submersible repeater and artificial satellite). Please note that FUJITSU will not be liable against you and/or any third party for any claims or damages arising in connection with above-mentioned uses of the products. • Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. • If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan. ©2004 FUJITSU LIMITED Printed in Japan ii 1. Checking the Delivered Product Before using the LQFP-80P probe header type2, confirm that the following components are included in the box: • LQFP-80P Probe Header type2 *1 :1 • Screws for securing header board (M2 × 10 mm, 0.4 mm pitch) :4 • Washer :4 • NQPACK080SD *2 :1 *3 • HQPACK080SD :1 • Operation manual (Japanese version) :1 • Operation manual (English version, this manual) :1 *1 : Referred to as "header board". Header board is mounted on YQPACK080SD (Tokyo Eletech Corporation), referred to as " YQPACK ". *2 : IC socket manufactured by Tokyo Eletech Corporation, referred to as " NQPACK ",and supplied with a special screwdriver and 3 guide pins. A socket offering higher reliability, NQPACK080SD-SL(Tokyo Eletech Corporation) (sold separately), can be used by making an IC socket mounting hole on the user system board. For more information, contact Tokyo Eletech Corporation. *3 : IC Socket cover manufactured by Tokyo Eletech Corporation, referred to as "HQPACK ", with 4 screws for securing HQPACK (M2 × 6 mm, 0.4 mm pitch). This product is used as an emulator system by combining with an optional " F2MC-16L/LX EMULATOR (MB2147-01)" and " F 2 MC-16L/LX EMULATOR PGA-299P ADAPTER BOARD (MB2147-20)" (sold separately). Consult the Sales Department or the Support Department of Fujitsu Limited for the adapter of this product. 2. Handling Precautions The header board is precision-manufactured to improve dimensional accuracy and to ensure reliable contact. The header is therefore sensitive to mechanical shock. To ensure correct use of the header in the proper environment, observe the following points regarding its insertion and removal: • To avoid placing stress on the NQPACK mounted on the user system board during connecting the header board. 1 3. Notes on Designing ■■ Restrictions of PC board for the user system Once the header board is connected to the user system, the heights of parts mounted in the space around the header board are restricted. The PC board of the user system must be designed with due consideration given to this restriction (Figure 1). 63.0 mm 28.0 mm 80.0 mm 32.0 mm Approximately 35.0 mm * Approximately 13.0 mm * * : The height differs slightly depending on how the socket are engaged. Figure 1 Header board dimensions 2 ■■ MCU footprint design notes Figure 2 shows the recommended dimensions of the NQPACK footprint mounted on the PC board of the user system. The PC board of the user system must be designed with due consideration given to this footprint as well as to the mass production MCU. For more information, contact the Tokyo Eletech Corporation. 15.1 mm 11.1 mm No.1 Pin 0.25 mm 2.0 mm 0.5 mm Figure 2 Recommended dimensions of the footprint for mounting the NQPACK 3 4. Procedure for Connecting the User System Before using the LQFP-80P probe header type2, mount the supplied NQPACK on the user system. The header board is used combining the adapter board. To connect the header board to the adapter board, use the flat cable (2 lines) supplied by the emulator sold separately. Refer to the hardware manuals of the adapter board about the way to connect. ■■ Connecting 1. To connect the header board to the user system, match the index mark (▲) on the NQPACK mounted on the user system with the index mark (▲) on the header board and then insert it (See Figure 3) . The pin of YQPACK is thin and easy to bent. Insert NQPACK after confirm that the pin of YQPACK is not bent. 2. Insert each screw for securing header board in each of the four drilled holes on the header board through a washer, and then first tighten the screws in opposing corners followed by the two remaining screws (See Figure 4) . To tighten the screws, use the special screwdriver supplied with the NQPACK to finally tighten the four screws in sequence. Tightening the screws too tight might result in a defective contact. Flat cable connector NQPACK Index (▲) Header board Index (▲) Figure 3 Index Position 4 Screws for securing header board Washer Header board YQPACK NQPACK User system Figure 4 Header board connection ■■ Disconnection To disconnect the header board from the user system, remove all four screws, and then pull the header board straight out of the socket 5 5. Mounting Mass Production MCUs To mount a mass production MCU on the user system, use the supplied HQPACK (See Figure 5). ■■ Mounting 1. To mount a mass production MCU on the user system, match the index mark (▲) on the NQPACK mounted on the user system with the index mark (●) on the mass production MCU. 2. Confirm that the mass production MCU is correctly mounted on the NQPACK. Next, insert the HQPACK into a NQPACK. The pin of HQPACK is thin and easy to bent. Insert NQPACK after confirm that the pin of HQPACK is not bent. 3. Insert each screw for securing HQPACK in each of four drilled holes on the HQPACK, and then first tighten the screws in opposing corners followed by the two remaining screws. To tighten the screws, use the special screwdriver supplied with the NQPACK to finally tighten the four screws in sequence. Tightening the screws too tight might result in a defective contact. Screws for securing HQPACK HQPACK Mass production MCU NQPACK User system Figure 5 Mounting a mass production MCU ■■ Disconnection To remove the HQPACK, remove all four screws, and pull out the HQPACK vertically. 6 6. Connector Pin Assignment The header board connects the signals of the evaluation MCU mounted on the adapter board via the flat cable connectors (two) on the header board according to pin information (the same assignments as YQPACK) about the production MCU. For details on the production MCU's pin information, refer to the datasheet or hardware manual for the relevant MCU. ■■ Pin Assignment Tables 1 and 2 list the pin assignments among the flat cable connector, the evaluation MCU on the adapter board, and the production MCU. For details on the names of signal conductors of the evaluation MCU, refer to the hardware manual for the emulator or adapter board. Comments in the tables are given below. *1 : Connected to the main power supply of the evaluation MCU. *2 : Connected to the main power supply (Vcc) of the production MCU. The connection pin numbers are 40 and 60. *3 : Connected to the ground of the evaluation MCU. *4 : Connected to the ground (Vss) of the production MCU. The connection pin numbers are 20 and 61. - : Unconnected pin (left open). 7 Table 1 Pin assignment of the flat cable connector B1 Connector Evaluation MCU Pin Numbers Pin Numbers 100 98 96 94 92 90 88 86 84 82 80 78 76 74 72 70 68 66 64 62 60 58 56 54 52 50 48 46 44 42 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 8 *3 *3 208 259 79 147 78 *3 146 223 26 94 219 *3 *1 226 275 105 224 *3 274 104 170 227 *3 *3 220 100 97 164 98 *3 23 165 276 108 172 *3 229 130 292 131 247 *3 293 248 133 62 134 *3 Production MCU Pin Numbers *4 *4 2 5 6 8 9 *4 79 *4 *2 *4 71 74 75 62 *4 *4 *4 63 65 66 *4 68 77 *4 12 27 28 30 31 *4 34 36 37 39 41 *4 Connector Evaluation MCU Pin Numbers Pin Numbers 99 97 95 93 91 89 87 85 83 81 79 77 75 73 71 69 67 65 63 61 59 57 55 53 51 49 47 45 43 41 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 *3 80 148 *3 207 258 206 77 160 *3 268 269 95 33 169 *3 34 167 35 225 32 *3 106 163 162 96 270 *3 221 273 271 222 99 *3 107 277 109 173 228 *3 193 194 132 *3 61 *3 195 63 294 *3 Production MCU Pin Numbers *4 3 4 *4 7 1 1 80 *4 14 16 26 *4 72 73 *4 76 *2 *4 64 15 67 69 70 *4 78 10 11 13 *2 *4 29 32 33 *4 35 *4 38 42 43 *4 Table 2 Pin assignment of the flat cable connector B2 Connector Evaluation MCU Pin Numbers Pin Numbers 100 98 96 94 92 90 88 86 84 82 80 78 76 74 72 70 68 66 64 62 60 58 56 54 52 50 48 46 44 42 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 *3 *3 267 149 260 209 *3 218 263 153 8 *1 *3 5 103 166 *3 151 *3 6 92 266 91 215 *3 16 264 213 14 203 *3 299 201 141 110 278 *3 *3 *1 252 71 138 *3 296 136 197 250 135 *3 Production MCU Pin Numbers *4 *4 19 *4 *2 *4 *4 *4 *4 *4 25 24 *4 *4 *2 59 57 56 *4 53 50 49 47 46 *4 Connector Evaluation MCU Pin Numbers Pin Numbers 99 97 95 93 91 89 87 85 83 81 79 77 75 73 71 69 67 65 63 61 59 57 55 53 51 49 47 45 43 41 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 *3 159 217 *3 81 82 83 87 212 *3 86 150 84 272 168 *3 7 210 261 158 216 *3 157 156 155 88 15 *3 154 255 143 202 142 *3 101 230 262 140 200 *3 199 70 251 198 137 *3 295 64 196 *3 Production MCU Pin Numbers *4 18 *4 *4 *4 *4 *4 *4 19 23 17 21 22 *4 58 55 54 52 51 *4 48 45 44 *4 9 SS01-71037-1E FUJITSU SEMICONDUCTOR • SUPPORT SYSTEM F2MC-16 Family EMULATOR LQFP-80P PROBE HEADER TYPE2 MB2147-561 OPERATION MANUAL July 2004 the first edition Published FUJITSU LIMITED Electronic Devices Edited Business Promotion Dept.