TAI-SAW TECHNOLOGY CO., LTD. No.3, Industrial 2nd Rd., Ping-Chen Industrial District, Taoyuan, Taiwan, R.O.C. TEL : 886-3-4690038 FAX : 886-3-4697532 E-mail : [email protected] Web: www.taisaw.com IF SAW Filter 35.225 MHz MODEL NO.: TB0692A REV. NO.:3 A. FEATURES: 1.IF Filter for Digital Cable TV B. MAXIMUM RATING: 1.DC voltage: 12 V. 2.AC voltage: 10 V. 3.Storage Temperature: -40°C to +85 °C. 4.Operating Temperature: -25 °C to +65 °C Terminating source impedance ZS=50Ω Terminating load impedance ZL=2kΩ//3 pF C. ELECTRICAL CHARACTERISTICS: Electrostatic Sensitive Device Attenuation ( ref. : 35.225 MHz): Center frequency fc Center frequency between 3dB point Insertion attenuation Reference level for the Following data 35.23 MHz 1dB Pass Bandwidth 3dB Pass Bandwidth 30dB Pass Bandwidth 31.43 MHz 38.81 MHz 31.20 MHz 39.00 MHz 30.00 MHz Lower side lobe 25.00-28.60 MHz 28.60-30.00 MHz Upper side lobe 40.15-43.10 MHz 43.10-45.00 MHz Reflected Wave Signal Suppression Feed through Signal Suppression Group delay ripple 31.20-39.00 MHz Phase linearity 31.20-39.00 MHz Impedance at 35.225 MHz Input Impedance Output Impedance Temperature Coefficient of frequency MIN. TYP. MAX. - 35.225 - MHz 20.7 21.5 23.7 dB 33.0 7.0 7.7 9.4 2.6 2.0 4.3 3.6 46.0 - MHz MHz MHz dB dB dB dB dB 35.0 31.0 40.0 42.0 - dB dB 30.0 34.0 42.0 - 33.0 40.0 50.0 54.0 - dB dB dB dB - 50 - ns - 6.4 - p-p deg. - 5.8||10.9 3.5||3.1 -72.0 TAI-SAW TECHNOLOGY CO., LTD. - KΩ||pF KΩ||pF ppm/K TST DCC Release document 2 D.FREQUENCY CHARACTERISTICS: TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 3 TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 4 E.TEST CIRCUIT F. Outline Drawing: Pin No. Functions 6 9 2 T ∆ □ 1. 2. 3. 4. 5. Input input - ground Chip carrier - ground Output Output □ : Week Code △ : Product / Year Code Product Code Table Year 2013 2017 2014 2018 2015 2019 2016 2020 Product Code B b B b TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 5 Week Code Table WK01 WK02 WK03 WK04 WK05 WK06 WK07 WK08 WK09 WK10 WK11 WK12 WK13 A B C D E F G H I J K L M WK14 WK15 WK16 WK17 WK18 WK19 WK20 WK21 WK22 WK23 WK24 WK25 WK26 N O P Q R S T U V W X Y Z WK27 WK28 WK29 WK30 WK31 WK32 WK33 WK34 WK35 WK36 WK37 WK38 WK39 a b c d e f g h i j k l m WK40 WK41 WK42 WK43 WK44 WK45 WK46 WK47 WK48 WK49 WK50 WK51 WK52 n o p q r s t u v w x y z G. PACKING 1 Plastic tube (1:5) A plastic tube contains 25PCS saw filters. 2 .double-trough Styrofoam (1:2) The plastic tubes were be placed in the double-trough Styrofoam. One trough contains 1000PCS saw filters, so a double-trough Styrofoam can contains 2000PCS saw filters. TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 6 3. Plastic tube in double-trough Styrofoam view(1:2) 4. Inner carton box (1:4) An inner carton box contains one double-trough Styrofoam. TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 7 5.Inner carton box view Inner Carton Box Packing two unit, each unit with one label b La 75㊣1.0 Outside el La l be 460㊣1.0 Outside 170㊣1.0 Outside double-trough styrofoam Plastic tube each one contains 25pcs One Unit contains 1000pcs(40*25pcs) The Inner Carton Box contains 2000pcs (2*1000pcs) 6.Outer carton box (1:4) A outer carton box contains four inner carton boxes, so one outer carton box contains 8000PCS saw filters. φ=25mm Storage condition after packing 1. Storage temperature:-10℃~+40℃ 2. Storage humidity:40%~70% 3. Using deadline: 2 year after purchasing Soldering Ability should be checked if over the using deadline TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 8 360 340 320 300 280 260 240 220 200 180 160 140 120 100 80 60 40 20 280 260 240 220 200 180 160 140 120 100 80 60 40 20 0 Temp ( Deg C) H. RECOMMENDED REFLOW PROFILE Time (Sec) TAI-SAW TECHNOLOGY CO., LTD. TST DCC Release document 9