UNISONIC TECHNOLOGIES CO., LTD U74AHC1G09 CMOS IC 2-INPUT AND GATE WITH OPEN DRAIN OUTPUT DESCRIPTION The U74AHC1G09 is a 2-input AND gate with open-drain output. And it provides the function Y=A×B FEATURES * Operation Voltage Range: 2~5.5V * Low Quiescent Current: ICC=1μA(Max) * High Speed: tPD=6ns@5V(Max) ORDERING INFORMATION Ordering Number U74AHC1G09G-AE5-R U74AHC1G09G-AF5-R U74AHC1G09G-AL5-R Package SOT-23-5 SOT-25 SOT-353 Packing Tape Reel Tape Reel Tape Reel MARKING www.unisonic.com.tw Copyright © 2015 Unisonic Technologies Co., Ltd 1 of 5 QW-R502-658.C U74AHC1G09 PIN CONFIGURATION VCC 5 1 A CMOS IC Y 4 2 B 3 GND FUNCTION TABLE INPUT A L L H H B L H L H OUTPUT Y L L L H(Z) (Note) Note: High impedance output state. Requires a pull-up resistor to get a high. LOGIC DIAGRAM (positive logic) IEC logic symbol UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 5 QW-R502-658.C U74AHC1G09 CMOS IC ABSOLUTE MAXIMUM RATING (unless otherwise specified) (Note 1 Note 2 ) PARAMETER SYMBOL RATINGS UNIT Supply Voltage VCC -0.5~7 V Input Voltage VIN -0.5~7 V Output Voltage VOUT -0.5~VCC+0.5 V Input Clamp Current IIK -20 mA Output Clamp Current IOK ±20 mA Output Current IOUT ±25 mA VCC or GND Current ICC ±50 mA Storage Temperature TSTG -65 ~ +150 °C Notes 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. RECOMMENDED OPERATING COMDITIONS PARAMETER SYMBOL VCC VIN VOUT Supply Voltage Input Voltage Output Voltage Input Transition Rise or Fall Rate VCC=3.3+0.3V VCC=5.0+0.5V t/v Operating Temperature TA RATINGS 2 ~ 5.5 0 ~ 5.5 0 ~ VCC 100 20 -40 ~ 125 UNIT V V V ns/V °C ELECTRICAL CHARACTERISTICS (TA=25°C) PARAMETER SYMBOL High-Level Input Voltage VIH Low-Level Input Voltage VIL Low-Level Output Voltage VOL Input Leakage Current Quiescent Supply Current Input Capacitance II(LEAK) IQ CIN TEST CONDITIONS VCC=2.0V VCC=3.0V VCC=5.5V VCC=2.0V VCC=3.0V VCC=5.5V VCC=2.0V IOL=50μA VCC=3.0V VCC=4.5V IOH=4mA, VCC=3.0V IOH=8mA, VCC=4.5V VIN=VCC or GND, VCC=0V to 5.5V VIN=VCC or GND, IOUT=0, VCC=5.5V VIN=VCC or GND, VCC=5.0V UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw MIN 1.5 2.1 3.85 TYP MAX UNIT V 4 0.5 0.9 1.65 0.1 0.1 0.1 0.36 0.36 ±0.1 1 10 V V μA μA pF 3 of 5 QW-R502-658.C U74AHC1G09 CMOS IC SWITCHING CHARACTERISTICS (Input: tR, tF≤3ns; PRR≤1MHz) PARAMETER SYMBOL tPZL Propagation delay from input (A or B)to output(Y) tPLZ tPZL tPLZ TEST CONDITIONS CL=15 pF CL=50 pF VCC =3.3±0.3 V CL=15 pF CL=50 pF CL=15 pF CL=50 pF VCC =5±0.5 V CL=15 pF CL=50 pF MIN TYP 3.6 6.5 3.6 6.5 2.5 4.6 2.5 4.6 MAX UNIT 7.0 11.0 ns 7.0 11.0 5.0 7.5 ns 5.0 7.5 OPERATING CHARACTERISTICS (TA=25°C) PARAMETER Power Dissipation Capacitance SYMBOL TEST CONDITIONS CPD No load, f=1MHz, VCC=5V UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw RATINGS 5 UNIT pF 4 of 5 QW-R502-658.C U74AHC1G09 CMOS IC TEST CIRCUIT AND WAVEFORMS S From Output VCC Open GND RL=1000Ω (Note) CL TEST tPLH/tPHL tPHZ/tPZH tPLZ/tPZL S Open GND VCC Test Circuit Note: CL includes probe and jig capacitance. UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 5 QW-R502-658.C