Model 100 www.vishay.com Vishay Spectrol 1 5/16" (33.3 mm) Single Turn Wirewound Precision Potentiometer FEATURES • Gangable up to 6 sections • Extra taps on request • Bushing and servo mount types available • Ohmic value range: 5 up to 35 k QUICK REFERENCE DATA Sensor type ROTATIONAL, single turn wirewound Output type Output by turrets Market appliance • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 Industrial 1 5/16" (33.3 mm) Dimensions ELECTRICAL SPECIFICATIONS PARAMETER Total resistance: Tolerance: 50 and above Below 50 STANDARD 5 to 20 k ±3% ±5% End voltage Linearity x total applied voltage for total resistance above 20 . 2.0 % of total applied voltage for 20 and below Linearity (independent): 5 to 100 100 to 500 500 to 3 k 3 k to 15 k 15 k and above STANDARD ± 1.0 % ± 0.5 % ± 0.5 % ± 0.5 % ± 0.5 % SPECIAL to 35 k ±1% ±3% BEST PRACTICAL ± 0.50 % ± 0.35 % ± 0.25 % ± 0.20 % ± 0.15 % 100 ENR (MIL-R-12934) Noise Electrical angle 352° ± 2° Power rating 2.75 W at 40 °C ambient Insulation resistance 100 M min, 500 VDC Dielectric strength 1000 VRMS, 60 Hz Taps (extra) Up to 13 (position tolerance: ± 1°) Phasing CCW taps of multiple sections aligned with CCW tap of section 1 to ± 1° Linearity x total resistance or 0.5 , whichever is greater Absolute minimum resistance ORDERING INFORMATION/DESCRIPTION The Model 100 can be ordered from this datasheet with a variety of alternate characteristics, as shown. For most rapid service on your order, please state: 100 S 1 10K BO1 MODEL MOUNTING TYPE NUMBER OF SECTIONS OHMIC VALUE PACKAGING B: Bushing S: Servo Up to 6 sections Box of 1 piece Other characteristics will be standard as described on this datasheet. If special characteristics are required, such as: special linearity tolerance, special resistance tolerance, extra taps, non-linear functions, etc., please state these on your order and allow additional lead time for delivery. SAP PART NUMBERING GUIDELINES 100 B 2 203 502 B01 Model STYLE NUMBER OF SECTIONS OHMIC VALUE OHMIC VALUE PACKAGING Section N° 1: 20K Section N° 2: 5K Box of 1 piece Bushing Revision: 05-Apr-13 Document Number: 57034 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Model 100 www.vishay.com Vishay Spectrol DIMENSIONS in inches (millimeters) BUSHING MOUNT: 100B/100-1... ± 0.010 0.705 (17.91) 1 0.242 MIN. (6.15) ± 0.031 0.875 (22.22) 0.375 (9.52) 3 22 1/2° TYP. + 0.0000 - 0.0010 ± 0.031 1 Ø 0.4062 MTG. (10.32) 0.062 (1.57) 0.2497 (6.34) 2 + 0.0000 - 0.0003 0.875R (22.22) MAX. Ø 1.312 (33.32) 0.562 (14.27) ± 0.031 3/ 0.062 (1.57) 8 - 32 UNEF 2A Ø 0.125 (3.18) MTG. FACE SERVO MOUNT: 100S/100-2... ± 0.010 ± 0.031 0.800 0.562 (20.32) (14.27) 1 0.337 MIN. (8.56) 2 0.073 (1.85) 0.062 (1.57) 1 + 0.0000 3 CW SCHEMATIC 0.062 (1.57) - 0.0003 Ø 0.2497 (6.34) + 0.0000 - 0.0005 Ø 1.1875 Ø 1.312 (30.16) (33.32) MTG. Ø 1.312 (33.32) Ø 1.187 (30.15) MAX. 1 ADD 0.566 ± 0.002 (14.38) FOR EACH ADDITIONAL SECTION TOLERANCES: UNLESS OTHERWISE NOTED. DECIMALS ± 0.005 ANGLES ± 2 ° MTG. FACE MECHANICAL SPECIFICATIONS PARAMETER Rotation Bearing type Ganging Torque (maximums) Servo, 1 section Bushing, 1 section Each additional section Mechanical tolerances (maximums): Shaft runout (TIR/In) Pilot dia. runout (TIR) Lateral runout (TIR) Shaft end play Shaft radial play Moment of inertia Weight Single section Each additional section Revision: 05-Apr-13 360° (continuous) Servo mount: ball bearing Bushing mount: sleeve bearing 6 sections maximum, terminal alignment, added sections, within ± 10° of section 1 terminals STARTING 0.60 oz. - in (43.20 g - cm) 1.00 oz. - in (72.00 g - cm) 0.30 oz. - in (21.60 g - cm) RUNNING 0.30 oz. - in (21.60 g - cm) 0.75 oz. - in (54.00 g - cm) 0.30 oz. - in (21.60 g - cm) BUSHING 0.002" (0.05 cm) 0.002" (0.05 cm) 0.005" (0.13 cm) 0.005" (0.13 cm) 0.004" (0.10 cm) SERVO 0.002" (0.05 cm) 0.002" (0.05 cm) 0.002" (0.05 cm) 0.005" (0.13 cm) 0.002" (0.05 cm) 1.0 g - cm2 per section maximum 2.0 oz. maximum (56.7 g) 0.75 oz. maximum (21.3 g) Document Number: 57034 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Model 100 www.vishay.com Vishay Spectrol MATERIAL SPECIFICATIONS Housing and lids ENVIRONMENTAL SPECIFICATIONS Aluminum, anodized Vibration Shaft Stainless steel, non-magnetic non-passivated Shock Terminals Brass, plated for solderability Rotational life Bushing mount hardware Lockwasher internal tooth: Panel nut: 15 g thru 2000 CPS 50 g Salt spray 96 h 1 million shaft revolutions Load life Steel, nickel plated Brass, nickel plated 900 h Temperature range - 55 °C to + 105 °C MARKING Units shall be marked with Vishay Spectrol name, model number and data code and on each section, resistance, resistance tolerance, linearity and terminal identification. Example of a marking for a standard part: 100-11103 Unit identification RATED POWER IN W POWER RATING CHART RESISTANCE ELEMENT DATA MAXIMUM MAXIMUM WIRE OHMS CURRENT VOLTAGE TEMP. ACROSS AT 70 °C PER COEF. COIL TURN AMBIENT (ppm/°C) (V) (mA) RESISTANCE VALUES () RESOLUTION (%) 2.5 5 0.346 0.017 742 3.7 800 2.0 10 0.298 0.030 524 5.2 800 1.5 20 0.236 0.047 371 7.4 800 1.0 50 0.244 0.122 235 12 20 0.5 100 0.222 0.222 166 17 20 200 0.181 0.361 117 23 20 500 0.178 0.885 74 37 20 1K 0.138 1.38 52 52 20 2K 0.105 2.09 37 74 20 5K 0.085 4.23 23 117 20 10K 0.069 6.84 17 166 20 20K 0.058 11.5 12 235 20 35K 0.058 20.0 8.8 310 20 4.0 3.5 3.0 0 25 50 75 100 AMBIENT TEMPERATURE IN °C Revision: 05-Apr-13 125 Document Number: 57034 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000