P10TG-xxxxE/Z4:1(H35)MLF PMP-SERIES Rev.09-2009 2 Watt 4:1 Wide Input Regulated DIP24 Metal Case 1.5 or 3.5 KV DC I/O Isolation SINGLE and DUAL Output Continuous Short Circuit Prot. Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PMP series P10TG-xxxxE/4:1(H30)MLF is a family of cost effective 2W single & dual output DC-DC converters with a wide input Voltage of 4:1. These converters are encapsulated in an ultra miniature DIP24 plastic or metal case. High performance features: 1500VDC up to 3500VDC input/output isolation, high efficiency operation, output voltage accuracy of ±1% maximum, wide input range 4:1 and low output ripple and noise. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter Input Reflected Ripple Current¹ 4:1 Wide Input Pi Type 35 mA pk-pk Output Specifications Voltage Accuracy Short Circuit Protection Line Regulation Load Regulation Ripple and Noise (20Mhz bandwidth) Temperature Coefficient ± 1% Indefinite (automatic recovery) ± 0.5% ± 0.5% / ± 1.5% (only 3.3 / ±3.3 Vout Models) 60 mV pk-pk ± 0.02% / °C General Specifications Efficiency I/O Isolation Voltage (3 sec.) I/O Isolation Capacity I/O Isolation Resistance Switching Frequency (typical) Humidity Reliability Calculated MTBF (MIL-HDBK-217F) See Table 1500 VDC (3500 VDC optional)* 470 pF, typ. 1000 MOhm 266 kHz, typ. 95% rel H > 1.121 Mhrs Physical Specifications Case Material Potting Material Weight Nickel Coated Copper Epoxy (UL94V-0 rated) ~ 17g, typ. Environment Specifications Operating Temperature Maximum Case Temperature Storage Temperature Cooling RoHS Conform -40 to +85°C (ambient) 100°C -40 to +125°C Free Air Convection Soldering 260°C, max. (1.5mm from case 10s.) PMP-Series – P10TG-xxxxE/Z4:1(H35)MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 Selection Guide Single/Dual Output Order # A) A) ) d (m mA) ad (mA d (m ( a a o ) d o L ² L C ) o . oa (uF) (VD Full Min VDC nt No L nt Full L oad age %) re n t re n t ge ( t L ( r r l e e a r r u u r t o y r r l o C V C ie n c t Vo t Cu put Cu acit put put put Inpu In p u In Out Out O ut Effic C ap SINGLE OUTPUT P10TG-243R3E4:1MLF P10TG-2405E4:1MLF P10TG-2409E4:1MLF P10TG-2412E4:1MLF P10TG-2415E4:1MLF P10TG-2424E4:1MLF P10TG-483R3E4:1MLF P10TG-4805E4:1MLF P10TG-4809E4:1MLF P10TG-4812E4:1MLF P10TG-4815E4:1MLF P10TG-4824E4:1MLF 9-36 9-36 9-36 9-36 9-36 9-36 18-72 18-72 18-72 18-72 18-72 18-72 15 15 15 15 15 15 12 12 12 12 12 12 110 109.6 106.8 106.8 106.8 106.8 55 54.82 53.4 53.4 53.4 53.4 3.3 5 9 12 15 24 3.3 5 9 12 15 24 0 0 0 0 0 0 0 0 0 0 0 0 600 400 222 166 133 83 600 400 222 166 133 83 75 76 78 78 78 78 75 76 78 78 78 78 470 330 68 47 22 10 470 330 68 47 22 10 DUAL OUTPUT P10TG-243R3Z4:1MLF P10TG-2405Z4:1MLF P10TG-2409Z4:1MLF P10TG-2412Z4:1MLF P10TG-2415Z4:1MLF P10TG-2424Z4:1MLF P10TG-483R3Z4:1MLF P10TG-4805Z4:1MLF P10TG-4809Z4:1MLF P10TG-4812Z4:1MLF P10TG-4815Z4:1MLF P10TG-4824Z4:1MLF 9-36 9-36 9-36 9-36 9-36 9-36 18-72 18-72 18-72 18-72 18-72 18-72 15 15 15 15 15 15 12 12 12 12 12 12 110 109.6 106.8 106.8 106.8 106.8 55.5 54.82 53.4 53.4 53.4 53.4 ± 3.3 ±5 ±9 ± 12 ± 15 ± 24 ± 3.3 ±5 ±9 ± 12 ± 15 ± 24 0 0 0 0 0 0 0 0 0 0 0 0 ± 303 ± 200 ± 111 ± 83 ± 66 ± 41 ± 303 ± 200 ± 111 ± 83 ± 66 ± 41 75 76 78 78 78 78 75 76 78 78 78 78 ± 220 ± 100 ± 33 ± 22 ± 10 ± 10 ± 220 ± 100 ± 33 ± 22 ± 10 ± 10 If you need other specifications, please enquire. * For optional 3.5kV DC I/O Isolation, please add “H35” before MLF! Example: P10TG-2405Z4:1H35MLF for 3.5kV PMP-Series – P10TG-xxxxE/Z4:1(H35)MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 Package / Pinning / Derating 27.94 (1.10) 1 All dimensions are typical in millimeters (inches). - Pin diameter: 0.5 +/-0.05 (0.02 +/-0.002) - Pin pitch tolerance: +/-0.35 (+/-0.014) - Case tolerance +/-0.5 (+/-0.02) Standard Drawing For exact pinning please see connection table! Specification may change without notice. 12 Bottom View 24 13 2.54 (0.10) DIP24 – METAL CASE 2.00 (0.08) 10.16 (0.40) PEAK Modelcode Datecode 31.75 (1.25) 3.05 (0.12) # 1 2 3 9 10 11 12 13 14 15 16 22 23 24 others SINGLE +Vin N.C. N.C. Omitted - Vout +Vout - Vin - Vin +Vout - Vout Omitted N.C. N.C. +Vin PIN CONNECTIONS DUAL SINGLE 3.5KV DUAL 3.5KV +Vin Omitted Omitted - Vout - Vin - Vin Common - Vin - Vin Omitted Omitted Common Common Omitted Omitted +Vout N.C. - Vout - Vin Omitted Omitted - Vin Omitted Omitted +Vout +Vout +Vout Common Omitted Omitted Omitted - Vout Common Common +Vin +Vin - Vout +Vin +Vin +Vin Omitted Omitted Omitted App Notes: ¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH. ² = Tested by nominal Vin and constant resistive load. PMP-Series – P10TG-xxxxE/Z4:1(H35)MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3