P14RG

P14RG-xxxxE/Z4:1LF
PMBW-SERIES
Rev.04-2009
3 Watt
4:1 Ultra Wide Input
Reg. Single and Dual Output
1.5 kV DC I/O Isolation
SIP9 case
On/Off Control
Contin. Short Circuit Protection
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
The PMBW 3Watt series is a family of cost effective DCDC converters with
4:1 ultra wide input, 3W single and dual output DC/DC converters with
control Pin. These converters are encapsulated in an ultra miniature SIP9
plastic case. High performance features: continuous / long time short circuit
protection with automatic restart and tight line / load regulation, high
efficiency operation and output voltage accuracy of ±2% maximum.
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range
Input Filter
Input Reflected Ripple Current¹
Start-up Time
4:1 Ultra Wide Input (see table)
Capacitor
20 mA pk-pk
10 mS, typ.
Output Specifications
Voltage Accuracy
Short Circuit Protection
Line Regulation
Load Regulation (0% - 100%)
Cross Regulation (Dual Output)
Ripple and Noise (20Mhz bandwidth)
Temperature Coefficient
Transient Recovery Time3
Transient Response Deviation3
± 1%
Indefinite (hiccup, Automatic Recovery)
± 0.5%
± 0.5%, max.(<10% load: ±1% for 3.3Vout and 5Vout)
± 5%
50 mV pk-pk
± 0.02% / °C
300 us, typ.
± 3%, max.
General Specifications
I/O Isolation Voltage (3 sec.)
I/O Isolation Capacity
I/O Isolation Resistance
Switching Frequency
Humidity
Reliability Calculated MTBF (MIL-HDBK-217F)
1500 VDC
500 pF, max.
1000 M Ohm
250 kHz
95% rel H
> 1.212 Mhrs
Physical Specifications
Case Material
Potting Material
Weight
Non Conductive Black Plastic (UL94V-0 rated)
Epoxy (UL94V-0 rated)
~ 6.5 g, typ.
Environment Specifications
Operating Temperature
Maximum Case Temperature
Storage Temperature
Cooling
RoHS Conform
-40 to +75°C (ambient)
100°C
-40 to +125°C
Free Air Convection (10mm distance required)
Soldering 260°C, max. (1.5mm from case 10s.)
PMBW-Series – P14RG-xxxxE/Z4:1LF – Single / Dual Output – SIP9 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/4
Selection Guide
Single/Dual Output
A)
A)
)
d (m
m A ) a d (m A
d (m
a
(
a
o
)
d
o
L
²
C
)
o
oa
ll L
n.
(uF)
(VD
VDC nt No L nt Full L
t Mi
t Fu
d
(
e
)
n
n
a
g
e
e
e
o
a
%
r
r
y(
rre
rre
ltag
or L
V o lt
Cur
Cur
ienc
t Vo
t Cu put Cu
acit
put
put
put
In p u
In p u
In
O ut
O ut
O ut
E ffic
Cap
Order #
SINGLE OUTPUT
P14RG-243R3E4:1LF
P14RG-2405E4:1LF
P14RG-2412E4:1LF
P14RG-2415E4:1LF
P14RG-483R3E4:1LF
P14RG-4805E4:1LF
P14RG-4812E4:1LF
P14RG-4815E4:1LF
9-36
9-36
9-36
9-36
18-72
18-72
18-72
18-72
10
10
10
10
5
5
5
5
125
153
149
148
65
78
75
75
3.3
5
12
15
3.3
5
12
15
0
0
0
0
0
0
0
0
700
600
250
200
700
600
250
200
77
82
84
85
75
81
84
84
2200
1000
165
100
2200
1000
165
100
A)
A)
)
d (m
m A ) a d (m A
d (m
a
(
a
o
)
d
o
L
²
C
)
o
oa
ll L
n.
(uF)
(VD
VDC nt No L nt Full L
t Mi
t Fu
d
(
e
)
n
n
a
g
e
e
e
o
a
%
r
r
rre
y(
rre
ltag
or L
V o lt
Cur
Cur
ienc
t Vo
t Cu put Cu
acit
put
put
put
In p u
In p u
In
O ut
O ut
O ut
E ffic
Cap
Order #
DUAL OUTPUT
P14RG-2405Z4:1LF
P14RG-2412Z4:1LF
P14RG-2415Z4:1LF
P14RG-4805Z4:1LF
P14RG-4812Z4:1LF
P14RG-4815Z4:1LF
9-36
9-36
9-36
18-72
18-72
18-72
10
10
10
5
5
5
155
149
149
78
75
76
±5
± 12
± 15
±5
± 12
± 15
0
0
0
0
0
0
± 300
± 125
± 100
± 300
± 125
± 100
81
84
84
81
84
83
± 470
± 100
± 47
± 470
± 100
± 47
If you need other specifications, please enquire.
PMBW-Series – P14RG-xxxxE/Z4:1LF – Single / Dual Output – SIP9 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/4
4.00
(0.16)
12.50
(0.49)
2.90
(0.11)
Package / Pinning / Derating
PIN CONNECTIONS
# SINGLE DUAL
1 - Vin
- Vin
2 +Vin
+Vin
3 Ctrl.
Ctrl.
6 +Vout
+Vout
7 N.C.
Common
8 N.C.
N.C.
9 - Vout
- Vout
App Notes:
1
= Measured Input reflected ripple current with a simulated source inductance of 12uH
= Tested by nominal Vin and constant resistive load.
3 = Test by normal Vin and 100%-25% load,25% Ioad step change; If Vout is 3.3V then the Transient Response Deviation is ±5%.
4 = Input filter components are required to help meet conducted emission class A
5 = An external filter capacitor is required to meet EN61000-4-4 and EN61000-4-5. (e.g. Nippon-chemi-con KY series, 220uF/100V)
2
EMC SPECIFICATIONS
Conducted
4
Emissions
Radiated
Emissions
ESD
RS
5
EFT
5
Surge
CS
PFMF
Remote ON/OFF
EN 55022
CLASS A
EN 55022
CLASS A
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
Perf. Criteria B
Perf. Criteria A
Perf. Criteria B
Perf. Criteria B
Perf. Criteria A
Perf. Criteria A
The MCU Pin Voltage is referenced to –Vin (Pin1)
ON:
0 – 0.6 VDC or open circuit
OFF: 2.7 - 15 VDC
OFF stand by input current: 5mA, max.
PMBW-Series – P14RG-xxxxE/Z4:1LF – Single / Dual Output – SIP9 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/4
App Notes
Test Configurations
Input Reflected Ripple Current
Test Step
Input reflected ripple current is measured
through a source inductor Lin(12uH) and a
source capacitor Cin(47uF, ESR<1.Ohm at
100KHz) at nominal input and full load.
Output Ripple & Noise
Measurement Test
The Scope measurement bandwidth is
20MHz.
EMI Filter
Input filter components (C1, L) are used to
help meet conducted emissions
equirement for the module. These
components should be mounted as close
as possible to the module; and all leads
should be minimized to decrease radiated
noise.
P14RG-24xx
P14RG-48xx
Input Components
C1
1210, 225k/100V,X7R (2pcs)
1210,105k/100V,X7R
L
6.8 uH
56 uH
PMBW-Series – P14RG-xxxxE/Z4:1LF – Single / Dual Output – SIP9 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 4/4