UNISONIC TECHNOLOGIES CO., LTD BYC5 DIODE Preliminary ULTRAFAST, LOW SWITCHING LOSS RECTIFIER DIODE DESCRIPTION The UTC BYC5 is a rectifier diode. It provides the designers with ultra-fast switching and low switching loss. The UTC BYC5 is suitable for half-bridge lighting ballasts, half-bridge/full-bridge switched mode power supplies and active power factor correction applications. FEATURES * Low Reverse Recovery Current * Ultra-Fast Switching * Low Switching Loss * Low Thermal Resistance SYMBOL TO-220-2 TO-252 ORDERING INFORMATION Ordering Number Package Lead Free Halogen Free BYC5L-6-TA2-T BYC5G-6-TA2-T TO-220-2 BYC5L-6-TN3-T BYC5G-6-TN3-T TO-252 BYC5L-6-TN3-R BYC5G-6-TN3-R TO-252 Note: Pin Assignment: A: Anode K: Cathode Tab: Mounting Base Pin Assignment 1 2 3 K A NC NC K A NC K A Packing Tube Tube Tape Reel MARKING www.unisonic.com.tw Copyright © 2015 Unisonic Technologies Co., Ltd 1 of 3 QW-R601-024.d BYC5 DIODE Preliminary ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL RATINGS UNIT Peak Repetitive Reverse Voltage VRRM 600 V Crest Working Reverse Voltage VRWM 600 V Continuous Reverse Voltage TTab ≤ 110°C VR 500 V δ =0.5; with reapplied VRRM(max); IF(AV) Average Forward Current 5 A TTab ≤89°C Repetitive Peak Forward δ =0.5; with reapplied VRRM(max); IFRM 10 A Current TTab ≤ 89°C t = 10ms 40 A Non-Repetitive Peak Forward t = 8.3ms IFSM Current sinusoidal; TJ =150°C prior to 44 A surge with reapplied VRWM(max) Junction Temperature TJ 150 °C Storage Temperature TSTG -40 ~ +150 °C Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. THERMAL CHARACTERISTICS PARAMETER TO-220-2 Junction to Ambient TO-252 TO-220-2 Junction to Case TO-252 SYMBOL θJA θJC RATINGS 60 80 2.5 3.5 UNIT °C/W °C/W °C/W °C/W ELECTRICAL CHARACTERISTICS (TJ =25°C, unless otherwise specified) PARAMETER SYMBOL Forward Voltage VF Reverse Current IR Reverse Recovery Time tRR Peak Reverse Recovery Current Forward Recovery Voltage IRRM VFR TEST CONDITIONS IF =5A, TJ =150°C IF =10A, TJ =150°C IF =5A VR=600V VR=500V, TJ=100°C IF =1A, VR=30V, dIF/dt=50A/μs IF=5A, VR=400V, dIF/dt=500A/μs TJ=100°C dIF/dt=50A/μs IF=5A, VR=400V, TJ=125°C dIF/dt=500A/μs IF =10A, dIF/dt=100A/μs UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw MIN TYP 1.4 1.75 2.0 9 0.9 30 19 25 0.7 8 9 MAX UNIT 1.75 V 2.2 V 2.9 V 100 µA 3.0 mA 50 ns ns 30 ns 3 A 11 A 11 V 2 of 3 QW-R601-024.d BYC5 DIODE Preliminary TYPICAL CHARACTERISTICS VIN VIN 150uH typ VIN=400V d.c. IL IR IF Output Diode 500V MOSFET ID Inductive load IL VO=400V d.c. Fig.1. Typical application, output rectifier in boost converter power factor correction circuit. Continuous conduction mode, where the transistor turns on whilst forward current is still flowing in the diode. Fig.2. Typical application, freewheeling diode in half bridge converter. Continuous conduction mode, where each transistor turns on whilst forward current is still flowing in the other bridge leg diode. UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 3 QW-R601-024.d