Data Sheet 26182.27B 5812-F BiMOS II 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40°C TO +85°C OPERATION The UCQ5812AF/EPF combine a 20-bit CMOS shift register, data latches, and control circuitry with high-voltage bipolar source drivers and active DMOS pull-downs for reduced supply current requirements. Although designed primarily for vacuum-fluorescent displays, the high-voltage, highcurrent outputs also allow them to be used in other peripheral power driver applications. OUT20 SERIAL DATA OUT LOAD SUPPLY LOGIC SUPPLY SERIAL DATA IN OUT 1 3 2 1 V DD 28 27 26 VBB OUT19 4 UCQ5812EPF 25 6 24 OUT 8 18 17 ST 19 16 11 CLK 20 15 10 14 21 12 OUT12 The CMOS shift register and latches allow direct interfacing with microprocessor-based systems. With a 5 V supply, they will operate to at least 3.3 MHz. At 12 V, higher speeds are possible. Especially useful for inter-digit blanking, the BLANKING input disables the output source drives and turns on the DMOS sink drivers. Use with TTL may require the use of appropriate pull-up resistors to ensure an input logic high. 22 9 T C U 2 D Y 1 L 8 O 6 N R P E O —A OUT 2 23 LATCHES 8 REGISTER LATCHES 7 REGISTER 5 13 OUT18 A CMOS serial data output enables cascade connections in applications requiring additional drive lines. Similar devices are available as the UCQ5810AF/LWF (10 bits), UCQ5811A (12 bits), and UCQ5818AF/EPF (32 bits). OUT9 OUT10 STROBE CLOCK GROUND BLANKING OUT11 t D C n E N e E U m R e N E ac I T l F p E N e r R O d R C e S FO nd I D — me Dwg. PP-059-1 ABSOLUTE MAXIMUM RATINGS at TA = 25°C Logic Supply Voltage, VDD ..................... 15 V Driver Supply Voltage, VBB .................... 60 V Continuous Output Current Range, IOUT ................................. -40 to +15 mA Input Voltage Range, VIN ........................ -0.3 V to VDD + 0.3 V Package Power Dissipation, PD (UCQ5812AF) ........................... 3.12 W* (UCQ5812EPF) ........................1.84 W† Operating Temperature Range, TA .................................. -40°C to +85°C Storage Temperature Range, TS ................................ -55°C to +150°C m o c e R * Derate at rate of 22 mW/°C above TA = +25°C † Derate at rate of 15 mW/°C above TA = +25°C Caution: Allegro CMOS devices have input static protection but are susceptible to damage when exposed to extremely high static electrical charges. Note that the UCQ5812AF (dual in-line package) and UCQ5812EPF (PLCC package) are electrically identical and share a common pin number assignment. The output source drivers are high-voltage PNP-NPN Darlingtons with a minimum breakdown of 60 V and are capable of sourcing up to 40 mA. The DMOS active pull-downs are capable of sinking up to 15 mA. The UCQ5812AF is supplied in a 28-pin dual in-line plastic package with 0.600" (15.24 mm) row spacing. For surface mounting, the UCQ5812EPF is furnished in 28-lead plastic chip carrier (quad pack) with 0.050"(1.22 mm) centers. Copper lead-frames, reduced supply current requirements and lower output saturation voltages, allow continuous operation, with all outputs sourcing 25 mA, of the UCQ5812AF over the operating temperature range, and the UCQ5812EPF up to +75°C. FEATURES ■ ■ ■ ■ ■ High-Speed Source Drivers 60 V Source Outputs To 3.3 MHz Data Input Rate Low-Output Saturation Voltages Low-Power CMOS Logic and Latches ■ Active DMOS Pull-Downs ■ Reduced Supply Current Requirements ■ Improved Replacement for TL5812 Always order by complete part number, e.g., UCQ5812AF . 5812-F 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40°C TO +85°C OPERATION UCQ5812AF LOAD SUPPLY 1 VBB FUNCTIONAL BLOCK DIAGRAM VDD 28 LOGIC SUPPLY SERIAL DATA OUT 2 27 SERIAL DATA IN OUT 20 3 26 OUT 1 OUT 19 4 25 OUT 2 OUT 18 5 24 OUT 3 OUT 17 6 23 OUT 4 OUT 16 7 22 OUT 5 OUT 15 8 21 OUT 6 OUT 14 9 20 OUT 7 OUT 13 10 19 OUT 8 OUT 12 11 18 OUT 9 OUT 11 12 17 OUT 10 BLANKING 13 ST 28 16 STROBE GROUND 14 CLK 27 15 CLOCK LOGIC SUPPLY V DD CLOCK SERIAL DATA IN SERIAL-PARALLEL SHIFT REGISTER STROBE LATCHES SERIAL DATA OUT BLANKING LATCHES REGISTER LATCHES REGISTER MOS BIPOLAR VBB GROUND OUT 1 OUT 2 OUT 3 OUT N LOAD SUPPLY Dwg. FP-013-1 TYPICAL INPUT CIRCUIT VDD BLNK Dwg. PP-029-7 IN Dwg. EP-010-5 TYPICAL OUTPUT DRIVER V BB OUT N Dwg. No. A-14,219 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 Copyright © 1995, 2002 Allegro MicroSystems, Inc. 5812-F 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40°C TO +85°C OPERATION ELECTRICAL CHARACTERISTICS over operating temperature range, at VBB = 60 V (unless otherwise noted). Limits @ VDD = 12 V Min. Typ. Max. Characteristic Symbol Output Leakage Current ICEX VOUT = 0 V, TA = +70°C — -5.0 -15 — -5.0 -15 µA Output Voltage VOUT(1) IOUT = -25 mA, VBB = 60 V 58 58.5 — 58 58.5 — V VOUT(0) IOUT = 1 mA IOUT = 2 mA — — 2.0 — 3.0 — — — — 2.0 — 3.5 V V IOUT(0) VOUT = 5 V to VBB 2.0 3.5 — — — — mA VOUT = 20 V to VBB — — — 8.0 13 — mA VIN(1) 3.5 — 5.3 10.5 — 12.3 V VIN(0) -0.3 — +0.8 -0.3 — +0.8 V Output Pull-Down Current Input Voltage Input Current Serial Data Test Conditions Limits @ VDD = 5 V Mln. Typ. Max. Units IIN(1) VIN = VDD — 0.05 0.5 — 0.1 1.0 µA IIN(0) VIN = 0.8 V — -0.05 -0.5 — -0.1 -1.0 µA VOUT(1) IOUT = -200 µA 4.5 4.7 — 11.7 11.8 — V VOUT(0) IOUT = 200 µA — 200 250 — 100 200 mV 3.3* — — — — — MHz Maximum Clock Frequency fclk Supply Current IDD(1) All Outputs High — 100 300 — 200 500 µA IDD(0) All Outputs Low — 100 300 — 200 500 µA IBB(1) Outputs High, No Load — 1.5 4.0 — 1.5 4.0 mA IBB(0) Outputs Low — 10 100 — 10 100 µA tPHL CL = 30 pF, 50% to 50% — 2000 — — 1000 — ns tPLH CL = 30 pF, 50% to 50% — 1000 — — 850 — ns Output Fall Time tf CL = 30 pF, 90% to 10% — 1450 — — 650 — ns Output Rise Time tr CL = 30 pF, 10% to 90% — 650 — — 700 — ns Blanking to Output Delay Negative current is defined as coming out of (sourcing) the specified device pin. * Operation at a clock frequency greater than the specified minimum value is possible but not warranteed. www.allegromicro.com 5812-F 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40°C TO +85°C OPERATION CLOCK A Serial Data present at the input is transferred to the shift register on the logic “0” to logic “1” transition of the CLOCK input pulse. On succeeding CLOCK pulses, the registers shift data information towards the SERIAL DATA OUTPUT. The SERIAL DATA must appear at the input prior to the rising edge of the CLOCK input waveform. D B DATA IN E F C STROBE BLANKING G Information present at any register is transferred to the respective latch when the STROBE is high (serial-to-parallel conversion). The latches will continue to accept new data as long as the STROBE is held high. Applications where the latches are bypassed (STROBE tied high) will require that the BLANKING input be high during serial data entry. OUTN Dwg. No. 12,649A TIMING REQUIREMENTS (TA = +25°C,VDD = 5 V, Logic Levels are VDD and Ground) A. Minimum Data Active Time Before Clock Pulse (Data Set-Up Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 ns B. Minimum Data Active Time After Clock Pulse (Data Hold Time) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 ns When the BLANKING input is high, the output source drivers are disabled (OFF); the DMOS sink drivers are ON, the information stored in the latches is not affected by the BLANKING input. With the BLANKING input low, the outputs are controlled by the state of their respective latches. C. Minimum Data Pulse Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 ns D. Minimum Clock Pulse Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 ns E. Minimum Time Between Clock Activation and Strobe . . . . . . . . . . . 300 ns F. Minimum Strobe Pulse Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 ns G. Typical Time Between Strobe Activation and Output Transistion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 ns Timing is representative of a 3.3 MHz clock. Higher speeds may be attainable with increased supply voltage; operation at high temperatures will reduce the specified maximum clock frequency. TRUTH TABLE Serial Data Clock Input Input Shift Register Contents Serial Data Strobe Output Input Latch Contents Output Contents I1 I2 H H R1 R2 … RN-2 RN-1 RN-1 L L R1 R2 … RN-2 RN-1 RN-1 X R1 R2 R3 … RN-1 RN RN X X X L R1 R2 R3 … RN-1 RN PN H P1 P2 P3 … PN-1 PN L P1 P2 P3 … PN1 PN X X H L L X I3 X … … P1 P2 P3 … L = Low Logic Level IN-1 IN X PN-1 PN H = High Logic Level X = Irrelevant I1 I2 X I3 X … … IN-1 IN Blanking X P = Present State R = Previous State 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 I1 I2 L I3 L … … IN-1 IN L 5812-F 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40°C TO +85°C OPERATION UCQ5812AF Dimensions in Inches (controlling dimensions) 28 0.015 0.008 15 0.700 MAX 0.580 0.485 0.600 BSC 1 2 0.070 0.030 3 14 0.100 4 1.565 1.380 BSC 0.005 MIN 0.250 MAX 0.200 0.115 0.015 MIN 0.022 0.014 Dwg. MA-003-28 in Dimensions in Millimeters (for reference only) 28 0.381 0.204 15 17.78 MAX 14.73 12.32 15.24 BSC 1 2 1.77 0.77 3 14 2.54 4 39.7 35.1 BSC 0.13 MIN 6.35 MAX 0.39 5.08 2.93 MIN 0.558 0.356 NOTES: 1. 2. 3. 4. Exact body and lead configuration at vendor’s option within limits shown. Lead spacing tolerance is non-cumulative. Lead thickness is measured at seating plane or below. Supplied in standard sticks/tubes of 12 devices. www.allegromicro.com Dwg. MA-003-28 mm 5812-F 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40°C TO +85°C OPERATION UCN5812EPF Dimensions in Inches (controlling dimensions) 18 0.013 0.021 12 19 0.219 0.191 11 0.026 0.032 0.456 0.450 INDEX AREA 0.495 0.485 0.050 BSC 0.219 0.191 25 5 26 0.020 28 1 4 0.456 0.450 0.495 0.485 MIN 0.165 0.180 Dwg. MA-005-28A in Dimensions in Millimeters (for reference only) 18 0.331 0.533 12 19 5.56 4.85 11 0.812 0.661 11.58 11.43 12.57 12.32 1.27 INDEX AREA BSC 5.56 4.85 25 5 26 0.51 MIN 4.57 4.20 28 1 4 11.582 11.430 12.57 12.32 Dwg. MA-005-28A mm NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown. 2. Lead spacing tolerance is non-cumulative. 3. Supplied in standard sticks/tubes of 38 devices or add “TR” to part number for tape and reel. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000 5812-F 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40°C TO +85°C OPERATION The products described here are manufactured under one or more U.S. patents or U.S. patents pending. Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that the information being relied upon is current. Allegro products are not authorized for use as critical components in life-support devices or systems without express written approval. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringement of patents or other rights of third parties which may result from its use. www.allegromicro.com 5812-F 20-BIT SERIAL-INPUT, LATCHED SOURCE DRIVERS FOR -40°C TO +85°C OPERATION POWER INTERFACE DRIVERS Function Output Ratings* Part Number† SERIAL-INPUT LATCHED DRIVERS 8-Bit (saturated drivers) 8-Bit 8-Bit 8-Bit 8-Bit 8-Bit (constant-current LED driver) 8-Bit (constant-current LED driver) 8-Bit (DMOS drivers) 8-Bit (DMOS drivers) 8-Bit (DMOS drivers) -120 mA 350 mA 350 mA 350 mA 350 mA 75 mA 120 mA 250 mA 350 mA 100 mA 50 V‡ 50 V 80 V 50 V‡ 80 V‡ 17 V 24 V 50 V 50 V‡ 50 V 5895 5821 5822 5841 5842 6275 6277 6595 6A595 6B595 10-Bit (active pull-downs) -25 mA 60 V 5810-F and 6810 12-Bit (active pull-downs) -25 mA 60 V 5811 75 mA 17 V 6276 20-Bit (active pull-downs) -25 mA 60 V 5812-F and 6812 32-Bit (active pull-downs) 32-Bit 32-Bit (saturated drivers) -25 mA 100 mA 100 mA 60 V 30 V 40 V 5818-F and 6818 5833 5832 16-Bit (constant-current LED driver) PARALLEL-INPUT LATCHED DRIVERS 4-Bit 350 mA 50 V‡ 5800 8-Bit 8-Bit 8-Bit (DMOS drivers) 8-Bit (DMOS drivers) -25 mA 350 mA 100 mA 250 mA 60 V 50 V‡ 50 V 50 V 5815 5801 6B273 6273 SPECIAL-PURPOSE DEVICES Unipolar Stepper Motor Translator/Driver Addressable 8-Bit Decoder/DMOS Driver Addressable 8-Bit Decoder/DMOS Driver Addressable 8-Bit Decoder/DMOS Driver Addressable 28-Line Decoder/Driver 1.25 A 250 mA 350 mA 100 mA 450 mA 50 V‡ 50 V 50 V‡ 50 V 30 V 5804 6259 6A259 6B259 6817 * Current is maximum specified test condition, voltage is maximum rating. See specification for sustaining voltage limits. Negative current is defined as coming out of (sourcing) the output. † Complete part number includes additional characters to indicate operating temperature range and package style. ‡ Internal transient-suppression diodes included for inductive-load protection. 115 Northeast Cutoff, Box 15036 Worcester, Massachusetts 01615-0036 (508) 853-5000