UDN5713: Dual Peripheral and Power Driver -- Transient Protected Outputs

5713
5713
Data Sheet
29307B
DUAL PERIPHERAL AND POWER DRIVER
DUAL PERIPHERAL AND POWER DRIVER
— TRANSIENT PROTECTED OUTPUTS
This “mini-DlP” dual peripheral and power driver is a bipolar
monolithic integrated circuit incorporating NOR logic gates, highcurrent switching transistors, and transient suppression diodes on the
same chip. The two output transistors are capable of simultaneously
sinking 300 mA continuously at ambient temperatures of up to +70°C.
In the OFF state, this driver will withstand at least 80 V.
T
C
U Y
D L
O
N
R
P EO
D
C
E
N
U
E
N ER
I
T
N EF
O
R
C
IS OR
D F
—
The UDN5713M dual driver is ideally suited for interface between
low-level or high-level logic and high-current/high-voltage loads.
Typical applications include driving peripheral loads such as incandescent lamps, light-emitting diodes, memories, and heaters with a load
current of up to 600 mA.
Dwg. No. A-9789
The integral transient suppression diodes allow the use of these
drivers with inductive loads such as relays, solenoids, or stepping
motors without the need for discrete diodes. Similar devices with four
drivers per package are the 5703 and 5706.
FEATURES
ABSOLUTE MAXIMUM RATINGS
Supply Voltage, VCC . . . . . . . . . . . . . . 7.0 V
Input Voltage, VIN . . . . . . . . . . . . . . . . . 30 V
Output Off-State Voltage,
VOFF . . . . . . . . . . . . . . . . . . . . . . . . 80 V
Output On-State Sink Current,
ION . . . . . . . . . . . . . . . . . . . . . . 600 mA
Suppression Diode Off-State Voltage,
VOFF . . . . . . . . . . . . . . . . . . . . . . . . 80 V
Suppression Diode On-State Current,
ION . . . . . . . . . . . . . . . . . . . . . . 600 mA
Power Dissipation at TA = 25°C, PD
Package . . . . . . . . . . . . . . . . . . . 1.5 W*
Each Driver . . . . . . . . . . . . . . . . . 0.8 W
Operating Free-Air Temperature Range,
TA . . . . . . . . . . . . . . . . . -20°C to +85°C
Storage Temperature Range,
TS . . . . . . . . . . . . . . . . -55°C to +150°C
■
■
■
■
DTL/TTL/PMOS/CMOS Compatible Inputs
Low Input Current
300 mA Continuous Output Current
Stand-off Voltage of 80 V
*Derate at the rate of 12.5 mW/°C above
TA = 25°C.
Always order by complete part number, e.g.,
UDN5713M .
5713
DUAL PERIPHERAL AND POWER DRIVER
RECOMMENDED OPERATING CONDITIONS
Min.
Nom.
Max.
Units
4.75
5.0
5.25
V
Operating Temperature Range
0
+25
+85
°C
Current into any output (ON state)
—
—
300
mA
Supply Voltage (VCC)
ELECTRICAL CHARACTERISTICS over operating temperature range
(unless otherwise noted).
Test Conditions
Limits
Characteristic
Symbol
Temp.
VCC
Driven
Input
Other
Input
Output
Min.
Typ.
“1” Input Voltage
VIN(1)
—
MIN
—
—
—
2.0
—
—
V
—
“0” Input Voltage
VIN(0)
—
MIN
—
—
—
—
—
0.8
V
—
“0” Input Current at all
Inputs except Strobe
IIN(0)
—
MAX
0.4 V
30 V
—
—
-50
-100
µA
2
“0” Input Current at Strobe
IIN(0)
—
MAX
0.4 V
30 V
—
—
-100
-200
µA
—
“1” Input Current at all
Inputs except Strobe
IIN(1)
—
MAX
30 V
0V
—
—
—
10
µA
2
“1” Input Current at Strobe
IIN(1)
—
MAX
30 V
0V
—
—
—
20
µA
—
Input Clamp Voltage
VIK
—
MIN
-12 mA
—
—
—
—
-1.5
V
—
Max. Units
Notes
SWITCHING CHARACTERISTICS at VCC = 5.0 V, TA = 25°C
Limits
Characteristic
Turn-on Delay Time
Symbol
Test Conditions
VS = 70 V, RL = 465 Ω (10 Watts),
tpd0
Min.
Typ.
Max. Units
Notes
—
200
500
ns
3
—
300
750
ns
3
CL = 15 pF
Turn-off Delay Time
VS = 70 V, RL = 465 Ω (10 Watts),
tpd1
CL = 15 pF
NOTES: 1. Typical values are at VCC = 5.0 V, TA = 25°C.
2. Each input tested separately.
3. Voltage values shown in the test circuit waveforms are with respect to network ground terminal.
4. Capacitance values specified include probe and test fixture capacitance.
INPUT PULSE CHARACTERISTICS
VIN(0) = 0 V
tf = 7 ns
VIN(1) = 3.5 V
tr = 14 ns
tp = 1 µs
PRR = 500 kHz
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
W
Copyright © 1976, 1997, Allegro MicroSystems, Inc.
5713
DUAL PERIPHERAL AND POWER DRIVER
ELECTRICAL CHARACTERISTICS over operating temperature range
(unless otherwise noted).
Test Conditions
Characteristic
Symbol
“1” Output Reverse Current
lOFF
“0” Output Voltage
VON
Limits
Temp.
VCC
Driven
Input
Other
Input
Output
Min.
Typ.
—
MIN
2.0 V
0V
80 V
—
—
100
µA
—
—
OPEN
2.0 V
0V
80 V
—
—
100
µA
—
—
MIN
0.8 V
0.8 V
150 mA
—
0.35
0.5
V
—
—
MIN
0.8 V
0.8 V
300 mA
—
0.5
0.7
V
—
0V
0V
OPEN
—
—
200
µA
3
Max. Units
Notes
Diode Leakage Current
ILK
NOM
NOM
Diode Forward Voltage Drop
VD
NOM
NOM
VCC
VCC
—
—
1.5
1.75
V
4
“1” Level Supply Current
lCC(1)
NOM
MAX
5.0 V
5.0 V
—
—
8.0
13
mA
1, 2
“0” Level Supply Current
lCC(0)
NOM
MAX
0V
0V
—
—
36
50
mA
1, 2
NOTES: 1. Typical values are at VCC = 5.0 V, TA = 25°C.
2. Per package.
3. Diode leakage current measured at VR = 80 V.
4. Diode forward voltage drop measured at IF = 300 mA.
5. Capacitance values specified include probe and test fixture capacitance.
Dwg. No. A-9123A
Dwg. No. A-7628C
5713
DUAL PERIPHERAL AND POWER DRIVER
Dimensions in Inches
8
0.014
0.008
5
0.430
MAX
0.280
0.240
0.300
BSC
1
0.070
0.045
4
0.005
MIN
0.400
0.355
0.210
MAX
0.015
0.150
0.115
MIN
0.022
0.014
0.100
Dwg. MA-001-8A in
BSC
Dimensions in Millimeters
(Based on 1” = 25.4 mm)
0.355
0.204
5
8
10.92
MAX
7.11
6.10
7.62
BSC
4
1
1.77
1.15
0.13
MIN
10.16
9.02
5.33
MAX
0.39
3.81
2.93
MIN
0.558
0.356
2.54
BSC
Dwg. MA-001-8A mm
Allegro MicroSystems, Inc. reserves the right to make, from time to time,
such departures from the detail specifications as may be required to permit
improvements in the design of its products.
NOTES: 1. Lead thickness is measured at seating plane or below.
The information included herein is believed to be accurate and reliable.
2. Lead spacing tolerance is non-cumulative.
However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor
3. Exact body and lead configuration at vendor’s option for any infringements of patents or other rights of third parties which may result
within limits shown.
from its use.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000