Datasheet

Photomicrosensor (Transmissive)
EE-SX3070/-SX4070
Be sure to read Precautions on page 25.
■ Dimensions
■ Features
Note: All units are in millimeters unless otherwise indicated.
• Incorporates an IC chip with a built-in detector element and amplifier.
• Incorporates a detector element with a built-in temperature compensation circuit.
• A wide supply voltage range: 4.5 to 16 VDC
• Directly connects with C-MOS and TTL.
• High resolution with a 0.5-mm-wide sensing aperture.
• Dark ON model (EE-SX3070)
• Light ON model (EE-SX4070)
Two, C1
Optical
axis
■ Absolute Maximum Ratings (Ta = 25°C)
Two, 0.7
Item
Emitter
Five, 0.25
(13.8)
Five, 0.5
(1.25)
Detector
Two, 0.7±0.1 dia.
K
O
A
G
Terminal No.
50 mA
(see note 1)
Reverse voltage
VR
4V
Power supply voltage
VCC
16 V
Output voltage
VOUT
28 V
Output current
IOUT
16 mA
Permissible output POUT
dissipation
V
Unless otherwise specified, the
tolerances are as shown below.
Name
Dimensions
Ambient temperature
A
K
Anode
Cathode
3 mm max.
±0.3
3 < mm ≤ 6
±0.375
V
Power supply
(Vcc)
6 < mm ≤ 10
±0.45
O
G
Output (OUT)
Ground (GND)
10 < mm ≤ 18
±0.55
18 < mm ≤ 30
±0.65
250 mW (see
note 1)
Operating
Topr
–40°C to 75°C
Storage
Tstg
–40°C to 85°C
Tsol
260°C
(see note 2)
Soldering temperature
Tolerance
Rated value
IF
(1.25)
2.35±0.1
Internal Circuit
Symbol
Forward current
Note: 1. Refer to the temperature rating chart if the ambient temperature exceeds 25°C.
2. Complete soldering within 10 seconds.
■ Electrical and Optical Characteristics (Ta = 25°C)
Item
Emitter
Detector
Symbol
Value
Condition
VF
1.2 V typ., 1.5 V max.
Reverse current
IR
0.01 μA typ., 10 μA max.
VR = 4 V
Peak emission wavelength
λP
940 nm typ.
IF = 20 mA
0.12 V typ., 0.4 V max.
VCC = 4.5 to 16 V, IOL = 16 mA, IF = 0 mA (EE-SX3070),
IF = 10 mA (EE-SX4070)
VCC = 16 V, RL = 1 kΩ, IF = 10 mA (EE-SX3070),
IF = 0 mA (EE-SX4070)
Forward voltage
Low-level output voltage VOL
High-level output voltage
VOH
15 V min.
Current consumption
ICC
IF = 20 mA
3.2 mA typ., 10 mA max.
VCC = 16 V
Peak spectral sensitivity λP
wavelength
870 nm typ.
VCC = 4.5 to 16 V
IFT
10 mA max.
VCC = 4.5 to 16 V
ΔH
15% typ.
VCC = 4.5 to 16 V (see note 1)
VCC = 4.5 to 16 V, IF = 20 mA, IOL = 16 mA (see note 2)
LED current when output is OFF
LED current when output is ON
Hysteresis
Response frequency
f
3 kHz min.
Response delay time
tPLH (tPHL)
3 μs typ.
VCC = 4.5 to 16 V, IF = 20 mA, IOL = 16 mA (see note 3)
Response delay time
tPHL (tPLH)
20 μs typ.
VCC = 4.5 to 16 V, IF = 20 mA, IOL = 16 mA (see note 3)
120
EE-SX3070/-SX4070 Photomicrosensor (Transmissive)
3. The following illustrations show the definition of response
delay time. The value in the parentheses applies to the EESX4070.
Note: 1. Hysteresis denotes the difference in forward LED
current value, expressed in percentage, calculated
from the respective forward LED currents when the
photo IC in turned from ON to OFF and when the
photo IC in turned from OFF to ON.
Input
2. The value of the response frequency is measured
by rotating the disk as shown below.
Output
2.1 mm
0.5 mm
Input
Output
EE-SX3070
EE-SX4070
Disk
0.5 mm
■ Engineering Data
Note: The values in the parentheses apply to the EE-SX4070.
IFT OFF (IFT ON)
IFT ON (IFT OFF)
Supply voltage VCC (V)
LED current IFT (mA)
Forward current IF (mA)
Ta = 70°C
Low-level Output Voltage vs.
Output Current (Typical)
VCC = 5 V
RL = 330 Ω
Ta = 25°C
VOUT
(EE-SX3@@)
VOUT
(EE-SX4@@)
Forward current IF (mA)
IFT OFF (IFT ON)
IFT ON (IFT OFF)
Low-level Output Voltage vs. Ambient Temperature Characteristics
(Typical)
Ta = 25°C
VCC = 5 V
IF = 0 mA (15 mA)
Response Delay Time vs. Forward
Current (Typical)
Ta = 25°C
RL = 1 kΩ
Supply voltage VCC (V)
VCC = 5 V
IF = 0 mA (15 mA)
IOL = 16 mA
IOL = 5 mA
Ambient temperature Ta (°C)
Output current IC (mA)
Response delay time tPHL, tPLH (μs)
Current consumption Icc (mA)
Ta = 25°C
IF = 0 mA (15 mA)
Ta = 25°C
Forward voltage VF (V)
Ambient temperature Ta (°C)
Current Consumption vs. Supply
Voltage (Typical)
Ta = −30°C
Low level output voltage VOL (V)
LED current IFT (mA)
VCC = 5 V
RL = 330 Ω
LED Current vs. Supply Voltage
(Typical)
Repeat Sensing Position
Characteristics (Typical)
Output transistor
LED Current vs. Ambient Temperature Characteristics (Typical)
Forward Current vs. Forward
Voltage Characteristics (Typical)
Low level output voltage VOL (V)
Ambient temperature Ta (°C)
Output allowable dissipation PC (mW)
Forward current IF (mA)
Forward Current vs. Collector
Dissipation Temperature Rating
Ta = 25°C
IF = 15 mA
VCC = 5 V
RL = 330 Ω
n = repeat 20 times
d1 = 0.01 mm
Center of optical axis
Distance d (mm)
EE-SX3070/-SX4070 Photomicrosensor (Transmissive)
121