Photomicrosensor (Transmissive) EE-SX3081/-SX4081 Be sure to read Precautions on page 25. ■ Dimensions ■ Features Note: All units are in millimeters unless otherwise indicated. • Incorporates an IC chip with a built-in detector element and amplifier. • Incorporates a detector element with a built-in temperature compensation circuit. • A wide supply voltage range: 4.5 to 16 VDC • Directly connects with C-MOS and TTL. • High resolution with a 0.5-mm-wide sensing aperture. • Dark ON model (EE-SX3081) • Light ON model (EE-SX4081) Four, C0.3 5±0.1 13.7+0.3 Two, C1±0.3 2.5±0.2 7.5±0.2 10±0.2 8.5±0.1 Optical axis ■ Absolute Maximum Ratings (Ta = 25°C) 6.5±0.1 2.5+0.1 Item 6.2±0.5 8.2±0.5 Emitter Cross section AA (10.5) (2.5) Detector Cross section BB Internal Circuit V O A G Unless otherwise specified, the tolerances are as shown below. Ambient temperature Reverse voltage VR 4V Power supply voltage VCC 16 V Output voltage VOUT 28 V Output current IOUT 16 mA Permissible output dissipation POUT 250 mW (see note 1) Operating Topr –40°C to 75°C Storage Tstg –40°C to 85°C Tsol 260°C (see note 2) Soldering temperature Dimensions Tolerance Terminal No. A Name Anode 3 mm max. ±0.3 K Cathode 3 < mm ≤ 6 ±0.375 V Power supply (Vcc) 6 < mm ≤ 10 ±0.45 O G Output (OUT) Ground (GND) 10 < mm ≤ 18 ±0.55 18 < mm ≤ 30 ±0.65 Rated value 50 mA (see note 1) Five, 0.25±0.1 (Five, 0.5±0.1) K Symbol IF Forward current Note: 1. Refer to the temperature rating chart if the ambient temperature exceeds 25°C. 2. Complete soldering within 10 seconds. ■ Electrical and Optical Characteristics (Ta = 25°C) Item Symbol Value Condition Forward voltage VF 1.2 V typ., 1.5 V max. IF = 20 mA Reverse current IR 0.01 μA typ., 10 μA max. VR = 4 V Peak emission wavelength λP 940 nm typ. IF = 20 mA Low-level output voltage VOL 0.12 V typ., 0.4 V max. VCC = 4.5 to 16 V, IOL = 16 mA, IF = 0 mA (EE-SX3081), IF = 8 mA (EE-SX4081) High-level output voltage VOH 15 V min. VCC = 16 V, RL = 1 kΩ, IF = 8 mA (EE-SX3081), IF = 0 mA (EE-SX4081) Current consumption ICC 3.2 mA typ., 10 mA max. VCC = 16 V 870 nm typ. VCC = 4.5 to 16 V IFT 8 mA max. VCC = 4.5 to 16 V Hysteresis ΔH 15% typ. VCC = 4.5 to 16 V (see note 1) Response frequency f 3 kHz min. VCC = 4.5 to 16 V, IF = 20 mA, IOL = 16 mA (see note 2) Response delay time tPLH (tPHL) 3 μs typ. VCC = 4.5 to 16 V, IF = 20 mA, IOL = 16 mA (see note 3) Response delay time tPHL (tPLH) 20 μs typ. VCC = 4.5 to 16 V, IF = 20 mA, IOL = 16 mA (see note 3) Emitter Detector Peak spectral sensitivi- λP ty wavelength LED current when output is OFF LED current when output is ON 122 EE-SX3081/-SX4081 Photomicrosensor (Transmissive) 3. The following illustrations show the definition of response delay time. The value in the parentheses applies to the EESX4081. Note: 1. Hysteresis denotes the difference in forward LED current value, expressed in percentage, calculated from the respective forward LED currents when the photo IC in turned from ON to OFF and when the photo IC in turned from OFF to ON. Input 2. The value of the response frequency is measured by rotating the disk as shown below. Output 2.1 mm 0.5 mm Input Output EE-SX3081 EE-SX4081 Disk 0.5 mm ■ Engineering Data Note: The values in the parentheses apply to the EE-SX4081. IFT OFF (IFT ON) IFT ON (IFT OFF) Supply voltage VCC (V) LED current IFT (mA) Forward current IF (mA) Low-level Output Voltage vs. Output Current (Typical) VCC = 5 V RL = 330 Ω Ta = 25°C VOUT (EE-SX3@@) VOUT (EE-SX4@@) Forward current IF (mA) IFT OFF (IFT ON) IFT ON (IFT OFF) Low-level Output Voltage vs. Ambient Temperature Characteristics (Typical) Ta = 25°C VCC = 5 V IF = 0 mA (15 mA) Response Delay Time vs. Forward Current (Typical) Ta = 25°C RL = 1 kΩ Supply voltage VCC (V) VCC = 5 V IF = 0 mA (15 mA) IOL = 16 mA IOL = 5 mA Ambient temperature Ta (°C) Output current IC (mA) Response delay time tPHL, tPLH (μs) Current consumption Icc (mA) Ta = 25°C IF = 0 mA (15 mA) Ta = 70°C Forward voltage VF (V) Ambient temperature Ta (°C) Current Consumption vs. Supply Voltage (Typical) Ta = −30°C Ta = 25°C Low level output voltage VOL (V) LED current IFT (mA) VCC = 5 V RL = 330 Ω LED Current vs. Supply Voltage (Typical) Repeat Sensing Position Characteristics (Typical) Output transistor LED Current vs. Ambient Temperature Characteristics (Typical) Forward Current vs. Forward Voltage Characteristics (Typical) Low level output voltage VOL (V) Ambient temperature Ta (°C) Output allowable dissipation PC (mW) Forward current IF (mA) Forward Current vs. Collector Dissipation Temperature Rating Ta = 25°C IF = 15 mA VCC = 5 V RL = 330 Ω n = repeat 20 times d1 = 0.01 mm Center of optical axis Distance d (mm) EE-SX3081/-SX4081 Photomicrosensor (Transmissive) 123