81302Dxx

GS81302D08/09/18/36E-375/350/333/300/250
375 MHz–250 MHz
1.8 V VDD
1.8 V and 1.5 V I/O
144Mb SigmaQuadTM-II
Burst of 4 SRAM
165-Bump BGA
Commercial Temp
Industrial Temp
Features
Clocking and Addressing Schemes
• Simultaneous Read and Write SigmaQuad™ Interface
• JEDEC-standard pinout and package
• Dual Double Data Rate interface
• Byte Write controls sampled at data-in time
• Burst of 4 Read and Write
• 1.8 V +100/–100 mV core power supply
• 1.5 V or 1.8 V HSTL Interface
• Pipelined read operation
• Fully coherent read and write pipelines
• ZQ pin for programmable output drive strength
• IEEE 1149.1 JTAG-compliant Boundary Scan
• Pin-compatible with present 144 Mb devices
• 165-bump, 15 mm x 17 mm, 1 mm bump pitch BGA package
• RoHS-compliant 165-bump BGA package available
The GS81302D08/09/18/36E SigmaQuad-II SRAMs are
synchronous devices. They employ two input register clock
inputs, K and K. K and K are independent single-ended clock
inputs, not differential inputs to a single differential clock input
buffer. The device also allows the user to manipulate the
output register clock inputs quasi independently with the C and
C clock inputs. C and C are also independent single-ended
clock inputs, not differential inputs. If the C clocks are tied
high, the K clocks are routed internally to fire the output
registers instead.
SigmaQuad™ Family Overview
The GS81302D08/09/18/36E are built in compliance with the
SigmaQuad-II SRAM pinout standard for Separate I/O
synchronous SRAMs. They are 150,994,944-bit (144Mb)
SRAMs. The GS81302D08/09/18/36E SigmaQuad SRAMs
are just one element in a family of low power, low voltage
HSTL I/O SRAMs designed to operate at the speeds needed to
implement economical high performance networking systems.
Each internal read and write operation in a SigmaQuad-II B4
RAM is four times wider than the device I/O bus. An input
data bus de-multiplexer is used to accumulate incoming data
before it is simultaneously written to the memory array. An
output data multiplexer is used to capture the data produced
from a single memory array read and then route it to the
appropriate output drivers as needed. Therefore the address
field of a SigmaQuad-II B4 RAM is always two address pins
less than the advertised index depth (e.g., the 16M x 8 has a
4M addressable index).
Parameter Synopsis
Rev: 1.04b 12/2011
-375
-350
-333
-300
-250
tKHKH
2.66 ns
2.86 ns
3.0 ns
3.3 ns
4.0 ns
tKHQV
0.45 ns
0.45 ns
0.45 ns
0.45 ns
0.45 ns
1/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
4M x 36 SigmaQuad-II SRAM—Top View
1
2
3
4
5
6
7
8
9
10
11
A
CQ
NA/SA
(288Mb)
SA
W
BW2
K
BW1
R
SA
SA
CQ
B
Q27
Q18
D18
SA
BW3
K
BW0
SA
D17
Q17
Q8
C
D27
Q28
D19
VSS
SA
NC
SA
VSS
D16
Q7
D8
D
D28
D20
Q19
VSS
VSS
VSS
VSS
VSS
Q16
D15
D7
E
Q29
D29
Q20
VDDQ
VSS
VSS
VSS
VDDQ
Q15
D6
Q6
F
Q30
Q21
D21
VDDQ
VDD
VSS
VDD
VDDQ
D14
Q14
Q5
G
D30
D22
Q22
VDDQ
VDD
VSS
VDD
VDDQ
Q13
D13
D5
H
Doff
VREF
VDDQ
VDDQ
VDD
VSS
VDD
VDDQ
VDDQ
VREF
ZQ
J
D31
Q31
D23
VDDQ
VDD
VSS
VDD
VDDQ
D12
Q4
D4
K
Q32
D32
Q23
VDDQ
VDD
VSS
VDD
VDDQ
Q12
D3
Q3
L
Q33
Q24
D24
VDDQ
VSS
VSS
VSS
VDDQ
D11
Q11
Q2
M
D33
Q34
D25
VSS
VSS
VSS
VSS
VSS
D10
Q1
D2
N
D34
D26
Q25
VSS
SA
SA
SA
VSS
Q10
D9
D1
P
Q35
D35
Q26
SA
SA
C
SA
SA
Q9
D0
Q0
R
TDO
TCK
SA
SA
SA
C
SA
SA
SA
TMS
TDI
11 x 15 Bump BGA—15 x 17 mm2 Body—1 mm Bump Pitch
Notes:
1. BW0 controls writes to D0:D8; BW1 controls writes to D9:D17; BW2 controls writes to D18:D26; BW3 controls writes to D27:D35.
2. A2 is the expansion address.
Rev: 1.04b 12/2011
2/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
8M x 18 SigmaQuad-II SRAM—Top View
1
2
3
4
5
6
7
8
9
10
11
A
CQ
SA
SA
W
BW1
K
NC/SA
(288Mb)
R
SA
SA
CQ
B
NC
Q9
D9
SA
NC
K
BW0
SA
NC
NC
Q8
C
NC
NC
D10
VSS
SA
NC
SA
VSS
NC
Q7
D8
D
NC
D11
Q10
VSS
VSS
VSS
VSS
VSS
NC
NC
D7
E
NC
NC
Q11
VDDQ
VSS
VSS
VSS
VDDQ
NC
D6
Q6
F
NC
Q12
D12
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
Q5
G
NC
D13
Q13
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
D5
H
Doff
VREF
VDDQ
VDDQ
VDD
VSS
VDD
VDDQ
VDDQ
VREF
ZQ
J
NC
NC
D14
VDDQ
VDD
VSS
VDD
VDDQ
NC
Q4
D4
K
NC
NC
Q14
VDDQ
VDD
VSS
VDD
VDDQ
NC
D3
Q3
L
NC
Q15
D15
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
Q2
M
NC
NC
D16
VSS
VSS
VSS
VSS
VSS
NC
Q1
D2
N
NC
D17
Q16
VSS
SA
SA
SA
VSS
NC
NC
D1
P
NC
NC
Q17
SA
SA
C
SA
SA
NC
D0
Q0
R
TDO
TCK
SA
SA
SA
C
SA
SA
SA
TMS
TDI
11 x 15 Bump BGA—15 x 17 mm2 Body—1 mm Bump Pitch
Notes:
1. BW0 controls writes to D0:D8. BW1 controls writes to D9:D17.
2. A7 is the expansion address.
Rev: 1.04b 12/2011
3/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
16M x 9 SigmaQuad-II SRAM—Top View
1
2
3
4
5
6
7
8
9
10
11
A
CQ
SA
SA
W
NC
K
SA
R
SA
SA
CQ
B
NC
NC
NC
SA
NC/SA
(288Mb)
K
BW0
SA
NC
NC
Q4
C
NC
NC
NC
VSS
SA
NC
SA
VSS
NC
NC
D4
D
NC
D5
NC
VSS
VSS
VSS
VSS
VSS
NC
NC
NC
E
NC
NC
Q5
VDDQ
VSS
VSS
VSS
VDDQ
NC
D3
Q3
F
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
G
NC
D6
Q6
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
H
Doff
VREF
VDDQ
VDDQ
VDD
VSS
VDD
VDDQ
VDDQ
VREF
ZQ
J
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
Q2
D2
K
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
L
NC
Q7
D7
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
Q1
M
NC
NC
NC
VSS
VSS
VSS
VSS
VSS
NC
NC
D1
N
NC
D8
NC
VSS
SA
SA
SA
VSS
NC
NC
NC
P
NC
NC
Q8
SA
SA
C
SA
SA
NC
D0
Q0
R
TDO
TCK
SA
SA
SA
C
SA
SA
SA
TMS
TDI
11 x 15 Bump BGA—13 x 15 mm2 Body—1 mm Bump Pitch
Notes:
1. BW0 controls writes to D0:D8.
2. B5 is the expansion address.
Rev: 1.04b 12/2011
4/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
16M x 8 SigmaQuad-II SRAM—Top View
1
2
3
4
5
6
7
8
9
10
11
A
CQ
SA
SA
W
NW1
K
SA
R
SA
SA
CQ
B
NC
NC
NC
SA
NC/SA
(288Mb)
K
NW0
SA
NC
NC
Q3
C
NC
NC
NC
VSS
SA
NC
SA
VSS
NC
NC
D3
D
NC
D4
NC
VSS
VSS
VSS
VSS
VSS
NC
NC
NC
E
NC
NC
Q4
VDDQ
VSS
VSS
VSS
VDDQ
NC
D2
Q2
F
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
G
NC
D5
Q5
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
H
Doff
VREF
VDDQ
VDDQ
VDD
VSS
VDD
VDDQ
VDDQ
VREF
ZQ
J
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
Q1
D1
K
NC
NC
NC
VDDQ
VDD
VSS
VDD
VDDQ
NC
NC
NC
L
NC
Q6
D6
VDDQ
VSS
VSS
VSS
VDDQ
NC
NC
Q0
M
NC
NC
NC
VSS
VSS
VSS
VSS
VSS
NC
NC
D0
N
NC
D7
NC
VSS
SA
SA
SA
VSS
NC
NC
NC
P
NC
NC
Q7
SA
SA
C
SA
SA
NC
NC
NC
R
TDO
TCK
SA
SA
SA
C
SA
SA
SA
TMS
TDI
11 x 15 Bump BGA—15 x 17 mm2 Body—1 mm Bump Pitch
Notes:
1. NW0 controls writes to D0:D3. NW1 controls writes to D4:D7.
2. B5 is the expansion address.
Rev: 1.04b 12/2011
5/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Pin Description Table
Symbol
Description
Type
Comments
SA
Synchronous Address Inputs
Input
—
R
Synchronous Read
Input
Active Low
W
Synchronous Write
Input
Active Low
BW0–BW3
Synchronous Byte Writes
Input
Active Low
x9/x18/x36 only
NW0–NW1
Nybble Write Control Pin
Input
Active Low
x8 only
K
Input Clock
Input
Active High
K
Input Clock
Input
Active Low
C
Output Clock
Input
Active High
C
Output Clock
Input
Active Low
TMS
Test Mode Select
Input
—
TDI
Test Data Input
Input
—
TCK
Test Clock Input
Input
—
TDO
Test Data Output
Output
—
VREF
HSTL Input Reference Voltage
Input
—
ZQ
Output Impedance Matching Input
Input
—
Qn
Synchronous Data Outputs
Output
—
Dn
Synchronous Data Inputs
Input
—
Doff
Disable DLL when low
Input
Active Low
CQ
Output Echo Clock
Output
—
CQ
Output Echo Clock
Output
—
VDD
Power Supply
Supply
1.8 V Nominal
VDDQ
Isolated Output Buffer Supply
Supply
1.5 or 1.8 V Nominal
VSS
Power Supply: Ground
Supply
—
NC
No Connect
—
—
Notes:
1. NC = Not Connected to die or any other pin
2. When ZQ pin is directly connected to VDDQ, output impedance is set to minimum value and it cannot be connected to ground or left
unconnected.
3. C, C, K, K cannot be set to VREF voltage.
Rev: 1.04b 12/2011
6/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Background
Separate I/O SRAMs, from a system architecture point of view, are attractive in applications where alternating reads and writes are
needed. Therefore, the SigmaQuad-II SRAM interface and truth table are optimized for alternating reads and writes. Separate I/O
SRAMs are unpopular in applications where multiple reads or multiple writes are needed because burst read or write transfers from
Separate I/O SRAMs can cut the RAM’s bandwidth in half.
SigmaQuad-II B4 SRAM DDR Read
The status of the Address Input, W, and R pins are sampled by the rising edges of K. W and R high causes chip disable. A low on
the Read Enable-bar pin, R, begins a read cycle. R is always ignored if the previous command loaded was a read command. Data
can be clocked out after the next rising edge of K with a rising edge of C (or by K if C and C are tied high), after the following
rising edge of K with a rising edge of C (or by K if C and C are tied high), after the next rising edge of K with a rising edge of C,
and after the following rising edge of K with a rising edge of C. Clocking in a high on the Read Enable-bar pin, R, begins a read
port deselect cycle.
Read A
NOP
Read B
Write C
Read D
Write E
NOP
K
K
Address
A
B
C
D
E
R
W
BWx
C
C+1
C+2
C+3
E
E+1
D
C
C+1
C+2
C+3
E
E+1
C
C
Q
A
A+1
A+2
A+3
B
B+1
B+2
B+3
D
D+1
D+2
CQ
CQ
Rev: 1.04b 12/2011
7/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
SigmaQuad-II B4 SRAM DDR Write
The status of the Address Input, W, and R pins are sampled by the rising edges of K. W and R high causes chip disable. A low on
the Write Enable-bar pin, W, and a high on the Read Enable-bar pin, R, begins a write cycle. W is always ignored if the previous
command was a write command. Data is clocked in by the next rising edge of K, the rising edge of K after that, the next rising edge
of K, and finally by the next rising edge of K.
Write A
NOP
Read B
Write C
Read D
Write E
NOP
K
K
Address
A
B
C
D
E
R
W
BWx
A
A+1
A+2
A+3
C
C+1
C+2
C+3
E
E+1
E+
D
A
A+1
A+2
A+3
C
C+1
C+2
C+3
E
E+1
E+
C
C
B
Q
B+1
B+2
B+3
D
D+1
D+2
CQ
CQ
Rev: 1.04b 12/2011
8/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Special Functions
Byte Write and Nybble Write Control
Byte Write Enable pins are sampled at the same time that Data In is sampled. A high on the Byte Write Enable pin associated with
a particular byte (e.g., BW0 controls D0–D8 inputs) will inhibit the storage of that particular byte, leaving whatever data may be
stored at the current address at that byte location undisturbed. Any or all of the Byte Write Enable pins may be driven high or low
during the data in sample times in a write sequence.
Each write enable command and write address loaded into the RAM provides the base address for a 4 beat data transfer. The x18
version of the RAM, for example, may write 72 bits in association with each address loaded. Any 9-bit byte may be masked in any
write sequence.
Nybble Write (4-bit) control is implemented on the 8-bit-wide version of the device. For the x8 version of the device, “Nybble
Write Enable” and “NBx” may be substituted in all the discussion above.
Example x18 RAM Write Sequence using Byte Write Enables
Data In Sample Time
BW0
BW1
D0–D8
D9–D17
Beat 1
0
1
Data In
Don’t Care
Beat 2
1
0
Don’t Care
Data In
Beat 3
0
0
Data In
Data In
Beat 4
1
0
Don’t Care
Data In
Resulting Write Operation
Byte 1
D0–D8
Byte 2
D9–D17
Byte 1
D0–D8
Byte 2
D9–D17
Byte 1
D0–D8
Byte 2
D9–D17
Byte 1
D0–D8
Byte 2
D9–D17
Written
Unchanged
Unchanged
Written
Written
Written
Unchanged
Written
Beat 1
Beat 2
Beat 3
Beat 4
Output Register Control
SigmaQuad-II SRAMs offer two mechanisms for controlling the output data registers. Typically, control is handled by the Output
Register Clock inputs, C and C. The Output Register Clock inputs can be used to make small phase adjustments in the firing of the
output registers by allowing the user to delay driving data out as much as a few nanoseconds beyond the next rising edges of the K
and K clocks. If the C and C clock inputs are tied high, the RAM reverts to K and K control of the outputs, allowing the RAM to
function as a conventional pipelined read SRAM.
Rev: 1.04b 12/2011
9/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Example Four Bank Depth Expansion Schematic
R3
W3
R2
W2
R1
W1
R0
W0
A0–An
K
D1–Dn
Bank 0
Bank 1
Bank 2
Bank 3
A
A
A
A
W
W
W
W
R
R
R
R
K
D
CQ
Q
C
K
D
CQ
Q
C
K
D
CQ
K
CQ
Q
D
Q
C
C
C
Q1–Qn
CQ0
CQ1
CQ2
CQ3
Note:
For simplicity BWn, NWn, K, and C are not shown.
Rev: 1.04b 12/2011
10/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
Rev: 1.04b 12/2011
A
A+1
A+2
B+2
D
A+3
B+3
C
E
B+1
B
D(2)
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
11/34
CQ[2]
CQ[2]
Q(2)
C[2]
C[2]
CQ[1]
CQ(1)
Q(1)
C[1]
C[1]
B+1
B
BWx(2)
B+2
B+3
D
C
Write D
D(1)
B
Read C
D
A
Write B
BWx(1)
W(2)
W(1)
R(2)
R(1)
Address
K
K
Read A
C+1
Read E
D+1
D+1
Burst of 4 SigmaQuad-II SRAM Depth Expansion
C+2
D+2
D+2
F
Write F
C+3
D+3
D+3
E
F
F
NOP
E+1
F+1
F+1
E+2
F
F
GS81302D08/09/18/36E-375/350/333/300/250
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
FLXDrive-II Output Driver Impedance Control
HSTL I/O SigmaQuad-II SRAMs are supplied with programmable impedance output drivers. The ZQ pin must be connected to
VSS via an external resistor, RQ, to allow the SRAM to monitor and adjust its output driver impedance. The value of RQ must be
5X the value of the desired RAM output impedance. The allowable range of RQ to guarantee impedance matching continuously is
between 175Ω and 350Ω. Periodic readjustment of the output driver impedance is necessary as the impedance is affected by drifts
in supply voltage and temperature. The SRAM’s output impedance circuitry compensates for drifts in supply voltage and
temperature. A clock cycle counter periodically triggers an impedance evaluation, resets and counts again. Each impedance
evaluation may move the output driver impedance level one step at a time towards the optimum level. The output driver is
implemented with discrete binary weighted impedance steps.
x36 Byte Write Enable (BWn) Truth Table
BW0
BW1
BW2
BW3
D0–D8
D9–D17
D18–D26
D27–D35
1
1
1
1
Don’t Care
Don’t Care
Don’t Care
Don’t Care
0
1
1
1
Data In
Don’t Care
Don’t Care
Don’t Care
1
0
1
1
Don’t Care
Data In
Don’t Care
Don’t Care
0
0
1
1
Data In
Data In
Don’t Care
Don’t Care
1
1
0
1
Don’t Care
Don’t Care
Data In
Don’t Care
0
1
0
1
Data In
Don’t Care
Data In
Don’t Care
1
0
0
1
Don’t Care
Data In
Data In
Don’t Care
0
0
0
1
Data In
Data In
Data In
Don’t Care
1
1
1
0
Don’t Care
Don’t Care
Don’t Care
Data In
0
1
1
0
Data In
Don’t Care
Don’t Care
Data In
1
0
1
0
Don’t Care
Data In
Don’t Care
Data In
0
0
1
0
Data In
Data In
Don’t Care
Data In
1
1
0
0
Don’t Care
Don’t Care
Data In
Data In
0
1
0
0
Data In
Don’t Care
Data In
Data In
1
0
0
0
Don’t Care
Data In
Data In
Data In
0
0
0
0
Data In
Data In
Data In
Data In
x18 Byte Write Enable (BWn) Truth Table
BW0
BW1
D0–D8
D9–D17
1
1
Don’t Care
Don’t Care
0
1
Data In
Don’t Care
1
0
Don’t Care
Data In
0
0
Data In
Data In
Rev: 1.04b 12/2011
12/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
x09 Byte Write Enable (BWn) Truth Table
BW0
D0–D8
1
Don’t Care
0
Data In
1
Don’t Care
0
Data In
x8 Nybble Write Enable (NWn) Truth Table
NW0
NW1
D0–D3
D4–D7
1
1
Don’t Care
Don’t Care
0
1
Data In
Don’t Care
1
0
Don’t Care
Data In
0
0
Data In
Data In
Rev: 1.04b 12/2011
13/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Absolute Maximum Ratings
(All voltages reference to VSS)
Symbol
Description
Value
Unit
VDD
Voltage on VDD Pins
–0.5 to 2.9
V
VDDQ
Voltage in VDDQ Pins
–0.5 to VDD
V
VREF
Voltage in VREF Pins
–0.5 to VDDQ
V
VI/O
Voltage on I/O Pins
–0.5 to VDDQ +0.5 (≤ 2.9 V max.)
V
VIN
Voltage on Other Input Pins
–0.5 to VDDQ +0.5 (≤ 2.9 V max.)
V
IIN
Input Current on Any Pin
+/–100
mA dc
IOUT
Output Current on Any I/O Pin
+/–100
mA dc
TJ
Maximum Junction Temperature
125
oC
TSTG
Storage Temperature
–55 to 125
oC
Note:
Permanent damage to the device may occur if the Absolute Maximum Ratings are exceeded. Operation should be restricted to Recommended
Operating Conditions. Exposure to conditions exceeding the Recommended Operating Conditions, for an extended period of time, may affect
reliability of this component.
Recommended Operating Conditions
Power Supplies
Parameter
Symbol
Min.
Typ.
Max.
Unit
Supply Voltage
VDD
1.7
1.8
1.9
V
I/O Supply Voltage
VDDQ
1.4
—
VDD
V
Reference Voltage
VREF
0.68
—
0.95
V
Note:
The power supplies need to be powered up simultaneously or in the following sequence: VDD, VDDQ, VREF, followed by signal inputs. The power
down sequence must be the reverse. VDDQ must not exceed VDD. For more information, read AN1021 SigmaQuad and SigmaDDR Power-Up.
Operating Temperature
Parameter
Symbol
Min.
Typ.
Max.
Unit
Junction Temperature
(Commercial Range Versions)
TJ
0
25
85
°C
Junction Temperature
(Industrial Range Versions)*
TJ
–40
25
100
°C
Note:
* The part numbers of Industrial Temperature Range versions end with the character “I”. Unless otherwise noted, all performance specifications
quoted are evaluated for worst case in the temperature range marked on the device.
Rev: 1.04b 12/2011
14/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Thermal Impedance
Package
Test PCB
Substrate
θ JA (C°/W)
Airflow = 0 m/s
θ JA (C°/W)
Airflow = 1 m/s
θ JA (C°/W)
Airflow = 2 m/s
θ JB (C°/W)
θ JC (C°/W)
165 BGA
4-layer
16.4
13.4
12.4
8.6
1.2
Notes:
1. Thermal Impedance data is based on a number of of samples from mulitple lots and should be viewed as a typical number.
2. Please refer to JEDEC standard JESD51-6.
3. The characteristics of the test fixture PCB influence reported thermal characteristics of the device. Be advised that a good thermal path to
the PCB can result in cooling or heating of the RAM depending on PCB temperature.
HSTL I/O DC Input Characteristics
Parameter
Symbol
Min
Max
Units
Notes
DC Input Logic High
VIH (dc)
VREF + 0.1
VDDQ + 0.3
V
1
DC Input Logic Low
VIL (dc)
–0.3
VREF – 0.1
V
1
Notes:
1. Compatible with both 1.8 V and 1.5 V I/O drivers.
2. These are DC test criteria. DC design criteria is VREF ± 50 mV. The AC VIH/VIL levels are defined separately for measuring timing
parameters.
3. VIL (Min)DC = –0.3 V, VIL(Min)AC = –1.5 V (pulse width ≤ 3 ns).
4. VIH (Max)DC = VDDQ + 0.3 V, VIH(Max)AC = VDDQ + 0.85 V (pulse width ≤ 3 ns).
HSTL I/O AC Input Characteristics
Parameter
Symbol
Min
Max
Units
Notes
AC Input Logic High
VIH (ac)
VREF + 200
—
mV
2,3
AC Input Logic Low
VIL (ac)
—
VREF – 200
mV
2,3
VREF (ac)
—
5% VREF (DC)
mV
1
VREF Peak-to-Peak AC Voltage
Notes:
1. The peak-to-peak AC component superimposed on VREF may not exceed 5% of the DC component of VREF.
2. To guarantee AC characteristics, VIH,VIL, Trise, and Tfall of inputs and clocks must be within 10% of each other.
3. For devices supplied with HSTL I/O input buffers. Compatible with both 1.8 V and 1.5 V I/O drivers.
Rev: 1.04b 12/2011
15/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Undershoot Measurement and Timing
Overshoot Measurement and Timing
VIH
20% tKHKH
VDD + 1.0 V
VSS
50%
50%
VDD
VSS – 1.0 V
20% tKHKH
VIL
Capacitance
(TA = 25oC, f = 1 MHZ, VDD = 1.8 V)
Parameter
Symbol
Test conditions
Typ.
Max.
Unit
Input Capacitance
CIN
VIN = 0 V
4
5
pF
Output Capacitance
COUT
VOUT = 0 V
6
7
pF
Clock Capacitance
CCLK
VIN = 0 V
5
6
pF
Note:
This parameter is sample tested.
AC Test Conditions
Parameter
Conditions
Input high level
1.25 V
Input low level
0.25 V
Max. input slew rate
2 V/ns
Input reference level
0.75 V
Output reference level
VDDQ/2
Note:
Test conditions as specified with output loading as shown unless otherwise noted.
AC Test Load Diagram
DQ
50Ω
RQ = 250 Ω (HSTL I/O)
VREF = 0.75 V
VT = VDDQ/2
Rev: 1.04b 12/2011
16/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Input and Output Leakage Characteristics
Parameter
Symbol
Test Conditions
Min.
Max
Input Leakage Current
(except mode pins)
IIL
VIN = 0 to VDD
–2 uA
2 uA
Doff
IILDOFF
VIN = 0 to VDD
–20 uA
2 uA
Output Leakage Current
IOL
Output Disable,
VOUT = 0 to VDDQ
–2 uA
2 uA
Programmable Impedance HSTL Output Driver DC Electrical Characteristics
Parameter
Symbol
Min.
Max.
Units
Notes
Output High Voltage
VOH1
VDDQ/2 – 0.12
VDDQ/2 + 0.12
V
1, 3
Output Low Voltage
VOL1
VDDQ/2 – 0.12
VDDQ/2 + 0.12
V
2, 3
Output High Voltage
VOH2
VDDQ – 0.2
VDDQ
V
4, 5
Output Low Voltage
VOL2
Vss
0.2
V
4, 6
Notes:
1. IOH = (VDDQ/2) / (RQ/5) +/– 15% @ VOH = VDDQ/2 (for: 175Ω ≤ RQ ≤ 350Ω).
2. IOL = (VDDQ/2) / (RQ/5) +/– 15% @ VOL = VDDQ/2 (for: 175Ω ≤ RQ ≤ 350Ω).
3. Parameter tested with RQ = 250Ω and VDDQ = 1.5 V or 1.8 V
4. 0Ω ≤ RQ ≤ ∞Ω
5. IOH = –1.0 mA
6. IOL = 1.0 mA
Rev: 1.04b 12/2011
17/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Operating Currents
-375
Parameter
Symbol
Test Conditions
Operating Current
(x36): DDR
IDD
Operating Current
(x18): DDR
-350
-333
-300
-250
Notes
0
to
70°C
–40
to
85°C
0
to
70°C
–40
to
85°C
0
to
70°C
–40
to
85°C
0
to
70°C
–40
to
85°C
0
to
70°C
–40
to
85°C
VDD = Max, IOUT = 0 mA
Cycle Time ≥ tKHKH Min
1105
mA
1115
mA
1055
mA
1065
mA
1000
mA
1010
mA
915
mA
925
mA
790
mA
800
mA
2, 3
IDD
VDD = Max, IOUT = 0 mA
Cycle Time ≥ tKHKH Min
995
mA
1005
mA
940
mA
950
mA
890
mA
900
mA
815
mA
825
mA
700
mA
710
mA
2, 3
Operating Current
(x9): DDR
IDD
VDD = Max, IOUT = 0 mA
Cycle Time ≥ tKHKH Min
995
mA
1005
mA
940
mA
950
mA
890
mA
900
mA
815
mA
825
mA
700
mA
710
mA
2, 3
Operating Current
(x8): DDR
IDD
VDD = Max, IOUT = 0 mA
Cycle Time ≥ tKHKH Min
995
mA
1005
mA
940
mA
950
mA
890
mA
900
mA
815
mA
825
mA
700
mA
710
mA
2, 3
Standby Current
(NOP): DDR
ISB1
310
mA
320
mA
295
mA
305
mA
275
mA
285
mA
265
mA
275
mA
250
mA
260
mA
2, 4
Device deselected,
IOUT = 0 mA, f = Max,
All Inputs ≤ 0.2 V or ≥ VDD – 0.2 V
Notes:
1.
2.
3.
4.
Power measured with output pins floating.
Minimum cycle, IOUT = 0 mA
Operating current is calculated with 50% read cycles and 50% write cycles.
Standby Current is only after all pending read and write burst operations are completed.
Rev: 1.04b 12/2011
18/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
AC Electrical Characteristics
Parameter
Symbol
-375
-350
-333
-300
-250
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Units
Notes
Clock
K, K Clock Cycle Time
C, C Clock Cycle Time
tKHKH
tCHCH
2.66
8.4
2.86
8.4
3.0
8.4
3.3
8.4
4.0
8.4
ns
tKC Variable
tKCVar
—
0.2
—
0.2
—
0.2
—
0.2
—
0.2
ns
K, K Clock High Pulse Width
C, C Clock High Pulse Width
tKHKL
tCHCL
1.06
—
1.14
—
1.2
—
1.32
—
1.6
—
ns
K, K Clock Low Pulse Width
C, C Clock Low Pulse Width
tKLKH
tCLCH
1.06
—
1.14
—
1.2
—
1.32
—
1.6
—
ns
K to K High
C to C High
tKHKH
tCHCH
1.13
—
1.23
—
1.35
—
1.49
—
1.8
—
ns
K to K High
C to C High
tKHKH
tCHCH
1.13
—
1.23
—
1.35
—
1.49
—
1.8
—
ns
K, K Clock High to C, C Clock High
tKHCH
0
1.21
0
1.29
0
1.35
0
1.49
0
1.8
ns
DLL Lock Time
tKCLock
1024
—
1024
—
1024
—
1024
—
1024
—
cycle
K Static to DLL reset
tKCReset
30
—
30
—
30
—
30
—
30
—
ns
K, K Clock High to Data Output Valid
C, C Clock High to Data Output Valid
tKHQV
tCHQV
—
0.45
—
0.45
—
0.45
—
0.45
—
0.45
ns
4
K, K Clock High to Data Output Hold
C, C Clock High to Data Output Hold
tKHQX
tCHQX
–0.45
—
–0.45
—
–0.45
—
–0.45
—
–0.45
—
ns
4
K, K Clock High to Echo Clock Valid
C, C Clock High to Echo Clock Valid
tKHCQV
tCHCQV
—
0.45
—
0.45
—
0.45
—
0.45
—
0.45
ns
K, K Clock High to Echo Clock Hold
C, C Clock High to Echo Clock Hold
tKHCQX
tCHCQX
–0.45
—
–0.45
—
–0.45
—
–0.45
—
–0.45
—
ns
CQ, CQ High Output Valid
tCQHQV
—
0.2
—
0.23
—
0.25
—
0.27
—
0.30
ns
8
CQ, CQ High Output Hold
tCQHQX
–0.2
—
–0.23
—
–0.25
—
–0.27
—
–0.30
—
ns
8
CQ Phase Distortion
tCQHCQH
tCQHCQH
0.9
—
1.0
—
1.10
—
1.24
—
1.55
—
ns
K Clock High to Data Output High-Z
C Clock High to Data Output High-Z
tKHQZ
tCHQZ
—
0.45
—
0.45
—
0.45
—
0.45
—
0.45
ns
4
K Clock High to Data Output Low-Z
C Clock High to Data Output Low-Z
tKHQX1
tCHQX1
–0.45
—
–0.45
—
–0.45
—
–0.45
—
–0.45
—
ns
4
Address Input Setup Time
tAVKH
0.4
—
0.4
—
0.4
—
0.4
—
0.5
—
ns
1
Control Input Setup Time (R, W)
tIVKH
0.4
—
0.4
—
0.4
—
0.4
—
0.5
—
ns
2
Control Input Setup Time (BWX), (BWX)
tIVKH
0.28
—
0.28
—
0.28
—
0.3
—
0.35
—
ns
3
Data Input Setup Time
tDVKH
0.28
—
0.28
—
0.28
—
0.3
—
0.35
—
ns
6
7
Output Times
Setup Times
Rev: 1.04b 12/2011
19/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
AC Electrical Characteristics (Continued)
Parameter
Symbol
-375
-350
-333
-300
-250
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Units
Notes
Hold Times
Address Input Hold Time
tKHAX
0.4
—
0.4
—
0.4
—
0.4
—
0.5
—
ns
1
Control Input Hold Time (R, W)
tKHIX
0.4
—
0.4
—
0.4
—
0.4
—
0.5
—
ns
2
Control Input Hold Time (BWX), (BWX)
tKHIX
0.28
—
0.28
—
0.28
—
0.3
—
0.35
—
ns
3
Data Input Hold Time
tKHDX
0.28
—
0.28
—
0.28
—
0.3
—
0.35
—
ns
Notes:
1.
2.
3.
4.
5.
6.
7.
8.
All Address inputs must meet the specified setup and hold times for all latching clock edges.
Control signals are R, W
Control signals are BW0, BW1, and (NW0, NW1 for x8) and (BW2, BW3 for x36).
If C, C are tied high, K, K become the references for C, C timing parameters
To avoid bus contention, at a given voltage and temperature tCHQX1 is bigger than tCHQZ. The specs as shown do not imply bus contention because tCHQX1 is a MIN
parameter that is worst case at totally different test conditions (0°C, 1.9 V) than tCHQZ, which is a MAX parameter (worst case at 70°C, 1.7 V). It is not possible for two
SRAMs on the same board to be at such different voltages and temperatures.
Clock phase jitter is the variance from clock rising edge to the next expected clock rising edge.
VDD slew rate must be less than 0.1 V DC per 50 ns for DLL lock retention. DLL lock time begins once VDD and input clock are stable.
Echo clock is very tightly controlled to data valid/data hold. By design, there is a ±0.1 ns variation from echo clock to data. The datasheet parameters reflect tester guard
bands and test setup variations.
Rev: 1.04b 12/2011
20/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
Rev: 1.04b 12/2011
KHIX
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
21/34
CQ
CQ
Q
KHCQV
KHCQX
KHCQV
A
KHQX1
B
KLKH
D
KHCQX
IVKH
B
KHKL
B
A
AVKH
KHKH
Write B
BWx
W
R
Address
K
K
Read A
KHIX
CQHQX
A+1
KHQV
DVKH
IVKH
IVKH
NOP
B+1
B+1
C
CQHQV
A+2
B+2
KHDX
B+2
KHIX
KHKHbar
A+3
KHQX
Write C
B+3
B+3
KHQZ
C
C
D
Read D
C+1
C+1
C+2
C+2
E
Write E
K and K Controlled Read-Write-Read Timing Diagram
C+3
C+3
D
E
E
D+1
NOP
E+1
E+1
D+2
GS81302D08/09/18/36E-375/350/333/300/250
© 2011, GSI Technology
Rev: 1.04b 12/2011
CHCQX
B
CHQV
KHKHbar
C
A+3
KHIX
IVKH
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
22/34
CQ
CQ
Q
C
C
CHCQX
CHCQX
CQHQX
CQHQV
A+2
A
A+1
CHQX
CHQX1
B
C
KLKH
Write C
D
KHIX
IVKH
KHAX
KHKL
Read B
C
CHCQV
A
AVKH
KHKH
NOP
BWx
W
R
Address
K
K
Read A
C+1
B+1
C+1
KHDX
IVKH
NOP
B+2
C+2
C+2
D
B+3
DVKH
KHIX
Write D
C and C Controlled Read-Write-Read Timing Diagram
C+3
C+3
CHQZ
D
D
NOP
D+1
D+1
D
D
GS81302D08/09/18/36E-375/350/333/300/250
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
JTAG Port Operation
Overview
The JTAG Port on this RAM operates in a manner that is compliant with IEEE Standard 1149.1-1990, a serial boundary scan
interface standard (commonly referred to as JTAG). The JTAG Port input interface levels scale with VDD. The JTAG output
drivers are powered by VDD.
Disabling the JTAG Port
It is possible to use this device without utilizing the JTAG port. The port is reset at power-up and will remain inactive unless
clocked. TCK, TDI, and TMS are designed with internal pull-up circuits.To assure normal operation of the RAM with the JTAG
Port unused, TCK, TDI, and TMS may be left floating or tied to either VDD or VSS. TDO should be left unconnected.
JTAG Pin Descriptions
Pin
Pin Name
I/O
Description
TCK
Test Clock
In
Clocks all TAP events. All inputs are captured on the rising edge of TCK and all outputs propagate
from the falling edge of TCK.
TMS
Test Mode Select
In
The TMS input is sampled on the rising edge of TCK. This is the command input for the TAP
controller state machine. An undriven TMS input will produce the same result as a logic one input
level.
In
The TDI input is sampled on the rising edge of TCK. This is the input side of the serial registers
placed between TDI and TDO. The register placed between TDI and TDO is determined by the
state of the TAP Controller state machine and the instruction that is currently loaded in the TAP
Instruction Register (refer to the TAP Controller State Diagram). An undriven TDI pin will produce
the same result as a logic one input level.
TDI
Test Data In
TDO
Test Data Out
Output that is active depending on the state of the TAP state machine. Output changes in
Out response to the falling edge of TCK. This is the output side of the serial registers placed between
TDI and TDO.
Note:
This device does not have a TRST (TAP Reset) pin. TRST is optional in IEEE 1149.1. The Test-Logic-Reset state is entered while TMS is
held high for five rising edges of TCK. The TAP Controller is also reset automaticly at power-up.
JTAG Port Registers
Overview
The various JTAG registers, refered to as Test Access Port or TAP Registers, are selected (one at a time) via the sequences of 1s
and 0s applied to TMS as TCK is strobed. Each of the TAP Registers is a serial shift register that captures serial input data on the
rising edge of TCK and pushes serial data out on the next falling edge of TCK. When a register is selected, it is placed between the
TDI and TDO pins.
Instruction Register
The Instruction Register holds the instructions that are executed by the TAP controller when it is moved into the Run, Test/Idle, or
the various data register states. Instructions are 3 bits long. The Instruction Register can be loaded when it is placed between the
TDI and TDO pins. The Instruction Register is automatically preloaded with the IDCODE instruction at power-up or whenever the
controller is placed in Test-Logic-Reset state.
Bypass Register
The Bypass Register is a single bit register that can be placed between TDI and TDO. It allows serial test data to be passed through
the RAM’s JTAG Port to another device in the scan chain with as little delay as possible.
Rev: 1.04b 12/2011
23/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Boundary Scan Register
The Boundary Scan Register is a collection of flip flops that can be preset by the logic level found on the RAM’s input or I/O pins.
The flip flops are then daisy chained together so the levels found can be shifted serially out of the JTAG Port’s TDO pin. The
Boundary Scan Register also includes a number of place holder flip flops (always set to a logic 1). The relationship between the
device pins and the bits in the Boundary Scan Register is described in the Scan Order Table following. The Boundary Scan
Register, under the control of the TAP Controller, is loaded with the contents of the RAMs I/O ring when the controller is in
Capture-DR state and then is placed between the TDI and TDO pins when the controller is moved to Shift-DR state. SAMPLE-Z,
SAMPLE/PRELOAD and EXTEST instructions can be used to activate the Boundary Scan Register.
JTAG TAP Block Diagram
·
·
·
·
·
·
·
·
Boundary Scan Register
·
·
0
Bypass Register
0
108
1
·
2 1 0
Instruction Register
TDI
TDO
ID Code Register
31 30 29
·
· ··
2 1 0
Control Signals
TMS
TCK
Test Access Port (TAP) Controller
Identification (ID) Register
The ID Register is a 32-bit register that is loaded with a device and vendor specific 32-bit code when the controller is put in
Capture-DR state with the IDCODE command loaded in the Instruction Register. The code is loaded from a 32-bit on-chip ROM.
It describes various attributes of the RAM as indicated below. The register is then placed between the TDI and TDO pins when the
controller is moved into Shift-DR state. Bit 0 in the register is the LSB and the first to reach TDO when shifting begins.
Rev: 1.04b 12/2011
24/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
GSI Technology
JEDEC Vendor
ID Code
See BSDL Model
Bit #
Presence Register
ID Register Contents
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
0
X
1
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
0
0 0 1 1 0 1 1 0 0 1
Tap Controller Instruction Set
Overview
There are two classes of instructions defined in the Standard 1149.1-1990; the standard (Public) instructions, and device specific
(Private) instructions. Some Public instructions are mandatory for 1149.1 compliance. Optional Public instructions must be
implemented in prescribed ways. The TAP on this device may be used to monitor all input and I/O pads, and can be used to load
address, data or control signals into the RAM or to preload the I/O buffers.
When the TAP controller is placed in Capture-IR state the two least significant bits of the instruction register are loaded with 01.
When the controller is moved to the Shift-IR state the Instruction Register is placed between TDI and TDO. In this state the desired
instruction is serially loaded through the TDI input (while the previous contents are shifted out at TDO). For all instructions, the
TAP executes newly loaded instructions only when the controller is moved to Update-IR state. The TAP instruction set for this
device is listed in the following table.
Rev: 1.04b 12/2011
25/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
JTAG Tap Controller State Diagram
1
0
Test Logic Reset
0
Run Test Idle
1
Select DR
1
Select IR
0
0
1
1
Capture DR
Capture IR
0
0
Shift DR
1
1
Shift IR
0
1
1
Exit1 DR
0
Exit1 IR
0
0
Pause DR
1
Exit2 DR
1
Update DR
1
1
0
0
Pause IR
1
Exit2 IR
0
1
0
0
Update IR
1
0
Instruction Descriptions
BYPASS
When the BYPASS instruction is loaded in the Instruction Register the Bypass Register is placed between TDI and TDO. This
occurs when the TAP controller is moved to the Shift-DR state. This allows the board level scan path to be shortened to facilitate testing of other devices in the scan path.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a Standard 1149.1 mandatory public instruction. When the SAMPLE / PRELOAD instruction is
loaded in the Instruction Register, moving the TAP controller into the Capture-DR state loads the data in the RAMs input and
I/O buffers into the Boundary Scan Register. Boundary Scan Register locations are not associated with an input or I/O pin, and
are loaded with the default state identified in the Boundary Scan Chain table at the end of this section of the datasheet. Because
the RAM clock is independent from the TAP Clock (TCK) it is possible for the TAP to attempt to capture the I/O ring contents
while the input buffers are in transition (i.e. in a metastable state). Although allowing the TAP to sample metastable inputs will
not harm the device, repeatable results cannot be expected. RAM input signals must be stabilized for long enough to meet the
TAPs input data capture set-up plus hold time (tTS plus tTH). The RAMs clock inputs need not be paused for any other TAP
operation except capturing the I/O ring contents into the Boundary Scan Register. Moving the controller to Shift-DR state then
places the boundary scan register between the TDI and TDO pins.
EXTEST
EXTEST is an IEEE 1149.1 mandatory public instruction. It is to be executed whenever the instruction register is loaded with
all logic 0s. The EXTEST command does not block or override the RAM’s input pins; therefore, the RAM’s internal state is
still determined by its input pins.
Rev: 1.04b 12/2011
26/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Typically, the Boundary Scan Register is loaded with the desired pattern of data with the SAMPLE/PRELOAD command.
Then the EXTEST command is used to output the Boundary Scan Register’s contents, in parallel, on the RAM’s data output
drivers on the falling edge of TCK when the controller is in the Update-IR state.
Alternately, the Boundary Scan Register may be loaded in parallel using the EXTEST command. When the EXTEST instruction is selected, the sate of all the RAM’s input and I/O pins, as well as the default values at Scan Register locations not associated with a pin, are transferred in parallel into the Boundary Scan Register on the rising edge of TCK in the Capture-DR
state, the RAM’s output pins drive out the value of the Boundary Scan Register location with which each output pin is associated.
IDCODE
The IDCODE instruction causes the ID ROM to be loaded into the ID register when the controller is in Capture-DR mode and
places the ID register between the TDI and TDO pins in Shift-DR mode. The IDCODE instruction is the default instruction
loaded in at power up and any time the controller is placed in the Test-Logic-Reset state.
SAMPLE-Z
If the SAMPLE-Z instruction is loaded in the instruction register, all RAM outputs are forced to an inactive drive state (highZ) and the Boundary Scan Register is connected between TDI and TDO when the TAP controller is moved to the Shift-DR
state.
JTAG TAP Instruction Set Summary
Instruction
Code
Description
Notes
EXTEST
000
Places the Boundary Scan Register between TDI and TDO.
1
IDCODE
001
Preloads ID Register and places it between TDI and TDO.
1, 2
SAMPLE-Z
010
Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO.
Forces all RAM output drivers to High-Z.
1
GSI
011
GSI private instruction.
1
SAMPLE/PRELOAD
100
Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO.
1
GSI
101
GSI private instruction.
1
GSI
110
GSI private instruction.
1
BYPASS
111
Places Bypass Register between TDI and TDO.
1
Notes:
1. Instruction codes expressed in binary, MSB on left, LSB on right.
2. Default instruction automatically loaded at power-up and in test-logic-reset state.
Rev: 1.04b 12/2011
27/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
JTAG Port Recommended Operating Conditions and DC Characteristics
Parameter
Symbol
Min.
Max.
Unit Notes
Test Port Input Low Voltage
VILJ
–0.3
0.3 * VDD
V
1
Test Port Input High Voltage
VIHJ
0.7 * VDD
VDD +0.3
V
1
TMS, TCK and TDI Input Leakage Current
IINHJ
–300
1
uA
2
TMS, TCK and TDI Input Leakage Current
IINLJ
–1
100
uA
3
TDO Output Leakage Current
IOLJ
–1
1
uA
4
Test Port Output High Voltage
VOHJ
VDD – 0.2
—
V
5, 6
Test Port Output Low Voltage
VOLJ
—
0.2
V
5, 7
Test Port Output CMOS High
VOHJC
VDD – 0.1
—
V
5, 8
Test Port Output CMOS Low
VOLJC
—
0.1
V
5, 9
Notes:
1. Input Under/overshoot voltage must be –1 V < Vi < VDDn +1 V not to exceed 2.9 V maximum, with a pulse width not to exceed 20% tTKC.
2. VILJ ≤ VIN ≤ VDDn
3. 0 V ≤ VIN ≤ VILJn
4. Output Disable, VOUT = 0 to VDDn
5. The TDO output driver is served by the VDD supply.
6. IOHJ = –2 mA
7. IOLJ = + 2 mA
8. IOHJC = –100 uA
9. IOLJC = +100 uA
JTAG Port AC Test Conditions
Parameter
Conditions
Input high level
VDD – 0.2 V
Input low level
0.2 V
Input slew rate
1 V/ns
Input reference level
VDD/2
Output reference level
VDD/2
JTAG Port AC Test Load
TDO
50Ω
30pF*
VDD/2
* Distributed Test Jig Capacitance
Notes:
1. Include scope and jig capacitance.
2. Test conditions as shown unless otherwise noted.
Rev: 1.04b 12/2011
28/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
JTAG Port Timing Diagram
tTKC
tTKH
tTKL
TCK
tTH
tTS
TDI
tTH
tTS
TMS
tTKQ
TDO
tTH
tTS
Parallel SRAM input
JTAG Port AC Electrical Characteristics
Parameter
Symbol
Min
Max
Unit
TCK Cycle Time
tTKC
50
—
ns
TCK Low to TDO Valid
tTKQ
—
20
ns
TCK High Pulse Width
tTKH
20
—
ns
TCK Low Pulse Width
tTKL
20
—
ns
TDI & TMS Set Up Time
tTS
10
—
ns
TDI & TMS Hold Time
tTH
10
—
ns
Rev: 1.04b 12/2011
29/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Package Dimensions—165-Bump FPBGA (Package E)
A1 CORNER
TOP VIEW
BOTTOM VIEW
Ø0.10 M C
Ø0.25 M C A B
Ø0.40~0.60 (165x)
1 2 3 4 5 6 7 8 9 10 11
A1 CORNER
11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
1.0
14.0
17±0.05
1.0
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
A
1.0
1.0
10.0
0.15 C
B
Rev: 1.04b 12/2011
0.20(4x)
0.36~0.46
1.50 MAX.
SEATING PLANE
C
15±0.05
30/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Ordering Information—GSI SigmaQuad-II SRAM
Org
Part Number1
Type
Package
Speed
(MHz)
TJ2
16M x 8
GS81302D08E-375
SigmaQuad-II SRAM
165-bump BGA
375
C
16M x 8
GS81302D08E-350
SigmaQuad-II SRAM
165-bump BGA
350
C
16M x 8
GS81302D08E-333
SigmaQuad-II SRAM
165-bump BGA
333
C
16M x 8
GS81302D08E-300
SigmaQuad-II SRAM
165-bump BGA
300
C
16M x 8
GS81302D08E-250
SigmaQuad-II SRAM
165-bump BGA
250
C
16M x 8
GS81302D08E-375I
SigmaQuad-II SRAM
165-bump BGA
375
I
16M x 8
GS81302D08E-350I
SigmaQuad-II SRAM
165-bump BGA
350
I
16M x 8
GS81302D08E-333I
SigmaQuad-II SRAM
165-bump BGA
333
I
16M x 8
GS81302D08E-300I
SigmaQuad-II SRAM
165-bump BGA
300
I
16M x 8
GS81302D08E-250I
SigmaQuad-II SRAM
165-bump BGA
250
I
16M x 9
GS81302D09E-375
SigmaQuad-II SRAM
165-bump BGA
375
C
16M x 9
GS81302D09E-350
SigmaQuad-II SRAM
165-bump BGA
350
C
16M x 9
GS81302D09E-333
SigmaQuad-II SRAM
165-bump BGA
333
C
16M x 9
GS81302D09E-300
SigmaQuad-II SRAM
165-bump BGA
300
C
16M x 9
GS81302D09E-250
SigmaQuad-II SRAM
165-bump BGA
250
C
16M x 9
GS81302D09E-375I
SigmaQuad-II SRAM
165-bump BGA
375
I
16M x 9
GS81302D09E-350I
SigmaQuad-II SRAM
165-bump BGA
350
I
16M x 9
GS81302D09E-333I
SigmaQuad-II SRAM
165-bump BGA
333
I
16M x 9
GS81302D09E-300I
SigmaQuad-II SRAM
165-bump BGA
300
I
16M x 9
GS81302D09E-250I
SigmaQuad-II SRAM
165-bump BGA
250
I
8M x 18
GS81302D18E-375
SigmaQuad-II SRAM
165-bump BGA
375
C
8M x 18
GS81302D18E-350
SigmaQuad-II SRAM
165-bump BGA
350
C
8M x 18
GS81302D18E-333
SigmaQuad-II SRAM
165-bump BGA
333
C
8M x 18
GS81302D18E-300
SigmaQuad-II SRAM
165-bump BGA
300
C
8M x 18
GS81302D18E-250
SigmaQuad-II SRAM
165-bump BGA
250
C
8M x 18
GS81302D18E-375I
SigmaQuad-II SRAM
165-bump BGA
375
I
8M x 18
GS81302D18E-350I
SigmaQuad-II SRAM
165-bump BGA
350
I
8M x 18
GS81302D18E-333I
SigmaQuad-II SRAM
165-bump BGA
333
I
8M x 18
GS81302D18E-300I
SigmaQuad-II SRAM
165-bump BGA
300
I
8M x 18
GS81302D18E-250I
SigmaQuad-II SRAM
165-bump BGA
250
I
4M x 36
GS81302D36E-375
SigmaQuad-II SRAM
165-bump BGA
375
C
Notes:
1. Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. Example: GS81302D36E-300T.
2. C = Commercial Temperature Range. I = Industrial Temperature Range.
Rev: 1.04b 12/2011
31/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Ordering Information—GSI SigmaQuad-II SRAM
Org
Part Number1
Type
Package
Speed
(MHz)
TJ2
4M x 36
GS81302D36E-350
SigmaQuad-II SRAM
165-bump BGA
350
C
4M x 36
GS81302D36E-333
SigmaQuad-II SRAM
165-bump BGA
333
C
4M x 36
GS81302D36E-300
SigmaQuad-II SRAM
165-bump BGA
300
C
4M x 36
GS81302D36E-250
SigmaQuad-II SRAM
165-bump BGA
250
C
4M x 36
GS81302D36E-375I
SigmaQuad-II SRAM
165-bump BGA
375
I
4M x 36
GS81302D36E-350I
SigmaQuad-II SRAM
165-bump BGA
350
I
4M x 36
GS81302D36E-333I
SigmaQuad-II SRAM
165-bump BGA
333
I
4M x 36
GS81302D36E-300I
SigmaQuad-II SRAM
165-bump BGA
300
I
4M x 36
GS81302D36E-250I
SigmaQuad-II SRAM
165-bump BGA
250
I
16M x 8
GS81302D08GE-375
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
375
C
16M x 8
GS81302D08GE-350
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
350
C
16M x 8
GS81302D08GE-333
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
333
C
16M x 8
GS81302D08GE-300
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
300
C
16M x 8
GS81302D08GE-250
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
250
C
16M x 8
GS81302D08GE-375I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
375
I
16M x 8
GS81302D08GE-350I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
350
I
16M x 8
GS81302D08GE-333I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
333
I
16M x 8
GS81302D08GE-300I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
300
I
16M x 8
GS81302D08GE-250I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
250
I
16M x 9
GS81302D09GE-375
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
375
C
16M x 9
GS81302D09GE-350
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
350
C
16M x 9
GS81302D09GE-333
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
333
C
16M x 9
GS81302D09GE-300
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
300
C
16M x 9
GS81302D09GE-250
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
250
C
16M x 9
GS81302D09GE-375I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
375
I
16M x 9
GS81302D09GE-350I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
350
I
16M x 9
GS81302D09GE-333I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
333
I
16M x 9
GS81302D09GE-300I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
300
I
16M x 9
GS81302D09GE-250I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
250
I
8M x 18
GS81302D18GE-375
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
375
C
8M x 18
GS81302D18GE-350
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
350
C
8M x 18
GS81302D18GE-333
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
333
C
Notes:
1. Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. Example: GS81302D36E-300T.
2. C = Commercial Temperature Range. I = Industrial Temperature Range.
Rev: 1.04b 12/2011
32/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
Ordering Information—GSI SigmaQuad-II SRAM
Org
Part Number1
Type
Package
Speed
(MHz)
TJ2
8M x 18
GS81302D18GE-300
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
300
C
8M x 18
GS81302D18GE-250
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
250
C
8M x 18
GS81302D18GE-375I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
375
I
8M x 18
GS81302D18GE-350I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
350
I
8M x 18
GS81302D18GE-333I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
333
I
8M x 18
GS81302D18GE-300I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
300
I
8M x 18
GS81302D18GE-250I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
250
I
4M x 36
GS81302D36GE-375
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
375
C
4M x 36
GS81302D36GE-350
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
350
C
4M x 36
GS81302D36GE-333
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
333
C
4M x 36
GS81302D36GE-300
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
300
C
4M x 36
GS81302D36GE-250
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
250
C
4M x 36
GS81302D36GE-375I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
375
I
4M x 36
GS81302D36GE-350I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
350
I
4M x 36
GS81302D36GE-333I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
333
I
4M x 36
GS81302D36GE-300I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
300
I
4M x 36
GS81302D36GE-250I
SigmaQuad-II SRAM
RoHS-compliant 165-bump BGA
250
I
Notes:
1. Customers requiring delivery in Tape and Reel should add the character “T” to the end of the part number. Example: GS81302D36E-300T.
2. C = Commercial Temperature Range. I = Industrial Temperature Range.
SigmaQuad-II Revision History
File Name
Format/Content
Creation of datasheet
81302Dxx_r1
Rev: 1.04b 12/2011
Description of changes
33/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology
GS81302D08/09/18/36E-375/350/333/300/250
SigmaQuad-II Revision History
File Name
Format/Content
81302Dxx_r1.00a
Editorial
Corrected Ordering Information Table
81302Dxx_r1.01
Content
Updated AC Characteristics Table
Updated 165 BGA Package Drawing
Updated JTAG Port Operation Section
81302Dxx_r1.02
Content
Added 300 MHz speed bin to Q
(Rev1.02a: removed CQ reference from SAMPLE-Z section in
JTAG Tap Instruction Set Summary)
(Rev1.02b: Updated DLL Lock time to 2048 cycles)
81302Dxx_r1.03
Content
Added 350 & 375 MHz speed bins
Removed 200 & 167 speed bins
(Rev1.03a: fixed erroneous data in AC Char table)
Content
Added Op Currents
Removed Preliminary banner due to MP status
(Rev1.04a: Editorial updates)
(Rev.104b: Updated DLL lock time in AC Char table)
81302Dxx_r1.04
Rev: 1.04b 12/2011
Description of changes
34/34
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2011, GSI Technology