da2303t

Document 550T
Isolation Transformers
For Texas Instruments RS-485
and Profibus Interfaces
• Developed to work with Texas Instruments ISO3086T and
ISO35T RS­‑485 Interfaces and ISO1176T Profibus Interface.
• Mounted on the Texas Instruments SN6501xEVM Evaluation
Modules used to analyze the SN6501 oscillator/power driver
• Center tapped primary and secondary windings
• 2500 Vrms, one minute interwinding isolation.
Core material Ferrite
Terminations RoHS tin-silver over tin over nickel over phos bronze.
Other terminations available at additional cost.
Weight 0.94 – 1.0 g
Ambient temperature –40°C to +125°C
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 600/13″ reel Plastic tape: 24 mm wide, 0.37 mm thick,
16 mm pocket spacing, 6.1 mm pocket depth
PCB washing Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf
LeakageVolt-time
Inductance2 DCR max (Ohms)3 inductance4 product5 Power6 Turns ratio
Pri / sec
Part number1
voltage
min (µH)
pri sec
max (µH)
(V-µsec)
(W)
pri : sec
DA2303-AL_
5 V to 5 V
45.6
0.130
0.260
1.0
34.4
7.2
1 : 1.5
or 3.3 V to 3.3 V
DA2304-AL_
3.3 V to 5 V
17.8
0.086
1. When ordering, please specify termination and packaging codes:
0.43
21.5
7.2
Parts manufactured prior
to November 2011 may
be marked differently.
Dot indicates pin 1
0.394 max
10,00
4
DA230x-AL
1
XXXXY
DA2303-ALD
Termination:L=RoHS compliant tin-silver over tin over nickel over
phos bronze.
Special order: T = RoHS tin-silver-copper
(95.5/4/0.5) or S = non-RoHS tin-lead (63/37).
Packaging:D=13″ machine ready reel. EIA-481 embossed plastic
tape (600 per full reel).
B
=Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge),
use code letter D instead.
2. Inductance is tested between pins 4 and 3 at 500 kHz, 0.5 Vrms, 0 Adc.
3. DCR is per winding.
4. Leakage inductance is for the primary with both windings connected in
series and with the secondary windings shorted.
5. Based on Bsat of the core at 25°C and number of turns on winding 4-3.
6. Calculated output power based on 150 kHz operating frequency.
Power varies depending on application.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
0.232
Pri
8
1 : 2.2
4
8
3
2
7
1
5
6
Sec
Primary windings and secondary
windings to be connected
in series on the PC board.
5
0.475 max
12,07
0.235 max
5,97
0.028
0,70
0.004 / 0,10
0.319 ±0.004
8,1 ±0,1
4
0.358
9,10
5
0.079
2,00
8
1
0.079
2,00
Dimensions are in
US +1-847-639-6400 [email protected]
UK +44-1236-730595 [email protected]
Taiwan +886-2-2264 3646 [email protected]
China +86-21-6218 8074 [email protected]
Singapore + 65-6484 8412 [email protected]
inches
mm
0.063
1,60
0.067
1,70
1
Recommended
Land Pattern
Document 550T Revised 11/29/11
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.