LED Protector PLEDxSW Datasheet

PLED Open LED Protectors
PLEDxSW Series
PLEDxSW Series - White Body
RoHS
Description
PLEDxSW Series open LED protectors provide a switching
electronic shunt path when an LED in an LED string fails as
an open circuit. This ensures that the remaining string of
LEDs will continue to function if a single LED does not.
PLEDxSW Series devices were designed to enable higher
reliability in indoor LED lighting applications such as
advertisement lighting and other applications. Additionally,
they are molded from white material to make them less
visible in the LED fixture and the white molding also reflects
more light to improve overall light engine efficiency.
Compatible with one, two and three watt LEDs that have
a nominal 3V forward characteristic, PLEDxSW Series
devices are available in SMB surface mount package. The
DO-214AA (SMB) low profile package is ideal for dense
board applications.
Agency Approvals
Agency
Agency File Number
E133083
Schematic Symbol
Features & Benefits
• Fast switching
• Automatically resets after
power cycle
•Low profile, small foot
print standard DO-214AA
package
Control
Circuit
• Compatible with industrial
lighting environments
• Compatible with PWM
frequencies up to 30 kHz
• RoHS compliant and
halogen-free
Electrical Characteristics (All parameters are measured at T=25°C unless otherwise noted)
Part Number
VBR
breakdown
VDRM
breakdown
IH
IS
IT@VT
VT @ IT = 1
Amp
Critical rate of
rise dV/dt
Volts
Volts
mAmps
mAmps
Amps
Volts
Volts
Min
Max
Max
Max
Max
5
100
1.0
1.2
250V/µs
Marking
Min
Max
Min
PLED6SW
PL6
6
16
6
PLED9SW
PL9
9
18
9
PLED13SW
PL13
13
26
13
PLED18SW
PL18
18
33
18
©2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 09/25/15
PLEDxSW Series
PLED Open LED Protectors
PLEDxSW Series
Thermal Considerations
Package
DO-214AA in White
Symbol
Parameter
Value
Unit
TJ
Operating Junction Temperature Range
-40 to +150
°C
TS
Storage Temperature Range
-65 to +150
°C
RθJA
Thermal Resistance: Junction to Ambient
DO-214AA: 901
DO-214AA: 402
°C/W
Notes:
1) Standard FR-4 PCB with Copper Pads (Recommended Size)
2) Aluminum PCB
Thickness: 1.6mm
Grade: 1-2 W/mK Thermal Conductivity
Trace thickness: 2 oz
Insulation layer thickness: 215 um
Solder Pad Dimensions: 2.0mm x 2.8mm (Recommended Size)
V-I Characteristics
VBR vs. Junction Temperature
+I
IT
IS
IH
-V
+V
VT
VDRM
VBR
P e rc e n t o f VBR C h a n g e – %
14
12
10
8
6
25 ˚C
4
2
0
-4
-6
-8
-40 -20
iH (T C = 2 5 ˚C )
R a tio o f
iH
Normalized DC Holding Current vs. Case Temperature
20
40
60
80
100 120 140 160
LED Interference Test Circuit
Q1
2.0
1.8
LED
Driver
2.0 Ω, 1/4 W
1.6
1.4
110 kΩ, 1/4 W
25 ˚C
1.2
1.0
+
0.8
-
0.6
0.4
-40 -20
0
Junction Temperature (TJ ) – ˚C
-I
Vbat
12 Vdc
Q2
2N2222
PWM
0
20
40 60
80 100 120 140 160
Case Temperature (T C ) – ˚C
©2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 09/25/15
Control
Circuit
ON/OFF
Switch
PLED
PLEDxSW Series
PLED Open LED Protectors
PLEDxSW Series
6 LEDs in Series 50% Duty Cycle 10kHz
5 LEDs and 1 PLED in Series 50% Duty Cycle 10kHz
Note:These two graphs show the current magnitude through the LED string with and without the PLED included. There is no noticeable effect on the LED current magnitude when the
PLED is included in the circuit as compared to the LED current magnitude when the PLED is not in the circuit. (The conversion factor for the test measurement in the graphs above is
10mA/mV for the Pearson coil measurement, therefore, the current magnitude in the first figure is 10mA*8.9 = 89mA, while the second figure is 91mA.)
PLED in the Off-State 10kHz
Channel 1: current through LEDs (318 mA)
Channel 2: voltage across PLED device (4.5 V)
©2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 09/25/15
PLED device zeners and then turns fully on 10kHz
Channel 1: current through LEDs (346 mA) and PLED device once it is fully turned on 2.5 μsec later
Channel 2: voltage across PLED device (21.3 V before PLED crowbars with 2 V drop)
PLEDxSW Series
PLED Open LED Protectors
PLEDxSW Series
Soldering Parameters
Pb – Free assembly
Reflow Condition
Pre Heat
- Temperature Min (Ts(min))
150°C
- Temperature Max (Ts(max))
200°C
- Time (min to max) (ts)
60 – 180 secs
Average ramp up rate (Liquidus Temp
(TL) to peak
3°C/second max
3°C/second max
TS(max) to TL - Ramp-up Rate
Reflow
217°C
- Temperature (TL) (Liquidus)
60 – 150 seconds
- Temperature (tL)
Peak Temperature (TP)
260+0/-5 °C
Time within 5°C of actual peak
Temperature (tp)
30 seconds
Ramp-down Rate
6°C/second max
Time 25°C to peak Temperature (TP)
8 minutes max
Do not exceed
260°C
Physical Specifications
Copper Alloy
Terminal Material
Terminal Finish
100% Matte Tin Plated
Body Material
UL recognized epoxy meeting flammability
classification 94V-0
Part Numbering System
PLED
Environmental Specifications
High Temperature
Voltage Blocking
MIL-STD-750: Method 1040, Condition A
80% min VDRM (VAC-peak), 150°C,
504 hours
Temperature Cycling
MIL-STD-750: Method 1051
-65°C to 150°C, 15-minute dwell,
100 cycles
Biased Temperature &
Humidity
EIA/JEDEC: JESD22-A101
80%VDRM, 85°C, 85%RH, 1008 hours
High Temperature
Storage
MIL-STD-750: Method 1031
150°C, 1008 hours
Low Temperature
Storage
-65°C, 1008 hours
Thermal Shock
MIL-STD-750: Method 1056
0°C to 100°C, 5-minute dwell,
10-second transfer, 10 cycles
Resistance to
Solder Heat
MIL-STD-750: Method 2031
260°C, 10 seconds
Part Marking System
X
TYPE
SW
DO-214AA
White Body
PLx
LED Protector
V DRM
6 Volts
9 Volts
13 Volts
18 Volts
XXXXX
PACKAGE TYPE
S: DO-214AA
Packaging
Package
Description
Packaging Quantity
Industry Standard
S
D O - 2 1 4 AA
2500
EIA-481-1
©2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 09/25/15
PLEDxSW Series
PLED Open LED Protectors
PLEDxSW Series
Dimensions - DO-214 AA Package
B
CASE TEMPERATURE
MEASURING POINT
D
A
C
K
Dimensions
H
F
E
G
0.079"
(2.0mm)
Inches
Millimeters
Min
Max
Min
Max
A
0.130
0.156
3.30
3.95
B
0.201
0.220
5.10
5.60
C
0.077
0.087
1.95
2.20
D
0.159
0.181
4.05
4.60
E
0.030
0.063
0.75
1.60
F
0.075
0.096
1.90
2.45
G
0.002
0.008
0.05
0.20
H
0.077
0.104
1.95
2.65
K
0.006
0.016
0.15
0.41
0.110"
(2.8mm)
0.079"
(2.0mm)
Recommended solder pad layout
(Reference Only)
DO-214AA Embossed Carrier Reel Pack (RP)
Meets all EIA-481-1 Standards
0.157
(4.0)
0.472
(12.0)
Cathode bar on this side
0.36
(9.2)
0.315
(8.0)
0.512 (13.0) Arbor
Hole Dia.
0.059 DIA
(1.5)
Cover tape
12.99
(330.0)
Dimensions
are in inches
(and millimeters).
0.49
(12.4)
Direction of Feed
©2015 Littelfuse, Inc.
Specifications are subject to change without notice.
Revision: 09/25/15
PLEDxSW Series