MKT1813 Datasheet

MKT1813
www.vishay.com
Vishay Roederstein
DC Film Capacitors
MKT Axial Type
FEATURES
• Supplied loose in box, taped on ammopack or
reel
• Material categorization:
For definitions of compliance please see
www.vishay.com/doc?99912
APPLICATIONS
Blocking, bypassing, filtering, timing, coupling and
decoupling, interference suppression in low voltage
applications.
QUICK REFERENCE DATA
Capacitance range (E12 series)
470 pF to 22 μF
Capacitance tolerance
± 20 %, ± 10 %, ± 5 %
Climatic testing class according to IEC 60068-1
55/100/56
Maximum application temperature
100 °C
Reference specifications
IEC 60384-2
Dielectric
Polyester film
Electrodes
Metallized
Construction
Mono and internal series construction
Encapsulation
Plastic-wrapped, epoxy resin sealed, flame retardant
Leads
Tinned wire
C-value; tolerance; rated voltage; manufacturer’s type; code for dielectric material;
manufacturer location; manufacturer's logo; year and week
Marking
Rated DC voltage
63 VDC, 100 VDC, 250 VDC, 400 VDC, 630 VDC, 1000 VDC
Rated AC voltage
40 VAC, 63 VAC, 160 VAC, 200 VAC, 220 VAC
Pull test on leads
Minimum 20 N in direction of leads according to IEC 60068-2-21
Bent test on leads
2 bends through 90° combined with 10 N tensile strength
Operational life > 300 000 h (40 °C/0.5 UR)
Failure rate < 2 FIT (40 °C/0.5 UR)
Reliability
Note
• For more detailed data and test requirements, contact [email protected]
DIMENSIONS in millimeters
Ød
40.0 ± 5.0
LEAD DIAMETER
d
Revision: 04-Jul-13
L
Max.
40.0 ± 5.0
D
Max.
D
0.6
 5.0
0.7
> 5.0  7.0
0.8
> 7.0 < 16.5
1.0
 16.5
Document Number: 26013
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKT1813
www.vishay.com
Vishay Roederstein
COMPOSITION OF CATALOG NUMBER
CAPACITANCE
(numerically)
MULTIPLIER
(nF)
0.1
2
1
3
10
4
100
5
MKT 1813
X
Example:
468 = 680 nF
XX
25
X
X
SPECIAL LETTER FOR TAPED
Bulk
TYPE
TOLERANCE
Un = 06 = 63 V
4
±5%
Un = 01 = 100 V
5
± 10 %
Un = 25 = 250 V
6
± 20 %
R
Reel
G
Ammopack
Un = 40 = 400 V
Un = 63 = 630 V
Un = 10 = 1000 V
Note
• For detailed tape specifications refer to “Packaging Information” www.vishay.com/doc?28139 or end of catalog
SPECIFIC REFERENCE DATA
DESCRIPTION
VALUE
Tangent of loss angle:
at 1 kHz
at 10 kHz
at 100 kHz
C = 0.1 μF
80 x 10-4
150 x 10-4
250 x 10-4
0.1 μF  C = 1.0 μF
80 x 10-4
150 x 10-4
-
C  1.0 μF
100 x 10-4
-
-
1000 VDC
CAPACITOR
LENGTH
(mm)
63 VDC
100 VDC
MAXIMUM PULSE RISE TIME (dU/dt)R [V/μs]
250 VDC
400 VDC
630 VDC
11
12
18
32
56
84
-
14
11
13
22
37
66
175
19
7
8
13
21
33
65
26.5
4
5
8
13
19
34
31.5
3
4
6
10
15
25
41.5
2
3
5
7
10
17
If the maximum pulse voltage is less than the rated voltage higher dU/dt values can be permitted.
R between leads, for C  0.33 μF and UR  100 V
> 15 000 M
R between leads, for C  0.33 μF and UR > 100 V
> 30 000 M
RC between leads, for C > 0.33 μF and UR  100 V
> 5000 s
RC between leads, for C > 0.33 μF and UR > 100 V
> 10 000 s
R between leads and case, 100 V; (foil method)
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s
Maximum application temperature
Revision: 04-Jul-13
> 30 000 M
1.6 x URDC, 1 min
100 °C
Document Number: 26013
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKT1813
www.vishay.com
Vishay Roederstein
ELECTRICAL DATA
URDC
(V)
CAP.
(μF)
CAPACITANCE
CODE
0.15
415
0.22
0.33
0.47
63
447
1.0
510
1.5
515
06
40
522
3.3
533
4.7
547
6.8
568
10.0
610
15.0
DIMENSIONS
D
L
5.0
11.0
5.0
11.0
-
-
6.0
14.0
-
-
7.0
14.0
-
-
6.5
19.0
-
-
7.5
19.0
8.5
19.0
-
-
8.5
26.5
7.5
19.0 (2)
10.0
26.5
8.5
19.0 (2)
11.5
26.5
-
-
12.0
31.5
14.5
31.5
-
-
615
18.0
31.5
22.0
622
17.5
41.5
0.068
368
5.0
11.0
0.10
410
5.0
11.0
0.15
415
0.22
422
0.47
Revision: 04-Jul-13
433
468
0.33
100
VAC
422
0.68
2.2
VOLTAGE
CODE
433
447
0.68
468
1.0
510
1.5
515
2.2
522
3.3
533
4.7
547
6.8
568
10.0
610
15.0
615
01
63
-
-
5.5
11.0
6.0
14.0
-
-
6.0
19.0
-
-
6.5
19.0
-
-
7.0
19.0
-
-
8.5
19.0
8.0
26.5
8.0
19.0 (2)
9.5
26.5
9.5
19.0 (2)
11.5
26.5
-
-
12.0
31.5
-
-
14.0
31.5
16.5
31.5
13.5
31.5 (2)
20.5
31.5
Document Number: 26013
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKT1813
www.vishay.com
Vishay Roederstein
ELECTRICAL DATA
URDC
(V)
CAP.
(μF)
CAPACITANCE
CODE
0.015
0.022
0.033
0.047
0.068
315
322
333
347
368
0.10
410
0.15
415
0.22
422
0.33
433
0.47
447
0.68
468
1.0
510
1.5
515
2.2
522
3.3
533
4.7
547
6.8
568
10.0
610
0.0068
0.010
0.015
0.022
0.033
0.047
0.068
268
310
315
322
333
347
368
0.10
410
0.15
415
0.22
422
0.33
433
0.47
447
0.68
468
1.0
510
1.5
515
2.2
522
250
400
Revision: 04-Jul-13
VOLTAGE
CODE
VAC
25
160
40
200
DIMENSIONS
D
L
5.0
5.0
5.0
6.0
6.0
6.0
7.0
7.0
8.0
9.0
8.5
9.0
10.0
11.0
13.0
15.5
14.0
15.5
14.5
17.5
21.0
5.0
5.0
6.0
6.0
6.0
7.0
8.0
7.0
8.5
8.0
8.0
9.5
9.5
11.0
11.5
13.5
14.0
13.0
16.5
-
11.0
11.0
11.0
14.0
14.0
14.0
14.0
19.0
19.0
19.0
26.5
19.0 (2)
26.5
31.5
31.5
31.5
26.5 (2)
41.5
31.5 (2)
41.5
41.5
11.0
11.0
14.0
14.0
14.0
14.0
14.0
19.0
19.0
26.5
19.0 (2)
26.5
19.0 (2)
26.5
31.5
31.5
41.5
31.5 (2)
41.5
-
Document Number: 26013
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKT1813
www.vishay.com
Vishay Roederstein
ELECTRICAL DATA
URDC
(V)
630
1000
CAP.
(μF)
CAPACITANCE
CODE
0.00047
0.00068
0.0010
0.0015
0.0022
0.0033
0.0047
0.0068
0.010
0.015
0.022
0.033
0.047
0.068
147
168
210
215
222
233
247
268
310
315
322
333
347
368
0.10
410
0.15
415
0.22
422
0.33
433
0.47
447
0.68
468
1.0
0.0010
0.0015
0.0022
0.0033
0.0047
0.0068
0.010
0.015
0.022
0.033
0.047
0.068
510
210
215
222
233
247
268
310
315
322
333
347
368
0.10
410
0.15
415
0.22
422
0.33
433
0.47
447
VOLTAGE
CODE
VAC
63 (1)
220
10 (1)
220
DIMENSIONS
D
L
5.0
5.0
5.0
5.0
5.0
5.0
5.0
6.0
6.0
6.5
7.5
6.5
7.5
8.5
10.5
9.5
10.0
11.5
13.5
14.5
14.0
14.5
16.5
5.5
6.0
6.0
7.0
6.0
6.0
6.5
7.5
9.0
10.5
12.0
11.0
13.0
13.5
16.0
16.0
19.0
-
11.0
11.0
11.0
11.0
11.0
11.0
11.0
14.0
14.0
14.0
14.0
19.0
19.0
19.0
19.0
19.0 (2)
26.5
26.5
26.5
31.5
26.5 (2)
41.5
41.5
14.0
14.0
14.0
14.0
19.0
19.0
19.0
19.0
19.0
19.0
19.0
26.5
26.5
31.5
31.5
41.5
41.5
-
Notes
• Pitch = L + 3.5
(1) Not suitable for mains applications
(2) For the smaller size please add “-M” at the end of the type designation (e.g. MKT1813-510/255-M)
Revision: 04-Jul-13
Document Number: 26013
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKT1813
www.vishay.com
Vishay Roederstein
RECOMMENDED PACKAGING
PACKAGING CODE
TYPE OF PACKAGING
REEL DIAMETER (mm)
ORDERING CODE EXAMPLES
G
Ammo
-
MKT1813-422-014-G
R
Reel
350
MKT1813-422-014-R
x
-
Bulk
-
MKT1813-422-014
x
x
Note
• Attention: Capacitors with L > 31.5 mm only as bulk available
EXAMPLE OF ORDERING CODE
TYPE
CAPACITANCE CODE
VOLTAGE CODE
TOLERANCE CODE (1)
PACKAGING CODE
MKT1813
410
06
5
G
Note
(1) Tolerance codes: 4 = 5 % (J); 5 = 10 % (K); 6 = 20 % (M)
MOUNTING
Normal Use
The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for
mounting in printed-circuit boards by means of automatic insertion machines.
For detailed tape specifications refer to packaging information: www.vishay.com/doc?28139 or end of catalog.
Specific Method of Mounting to Withstand Vibration and Shock
In order to withstand vibration and shock tests, it must be ensured that the capacitor body is in good contact with the
printed-circuit board:
• For L  19 mm capacitors shall be mechanically fixed by the leads.
• For larger pitches the capacitors shall be mounted in the same way and the body clamped.
• The maximum diameter and length of the capacitors are specified in the “Dimensions” table.
• Eccentricity as shown in the drawing below.
Space Requirements on Printed-Circuit Board
The maximum length and width of film capacitors is shown in the drawing:
• Eccentricity as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product concerned.
• Product height with seating plane as given by “IEC 60717” as reference: hmax.  h + 0.4 mm or hmax.  h' + 0.4 mm
1 mm
Storage Temperature
Tstg = - 25 °C to + 35 °C with RH maximum 75 % without condensation
Ratings and Characteristics Reference Conditions
Unless otherwise specified, all electrical values apply to an ambient temperature of 23 °C ± 1 °C, an atmospheric pressure of
86 kPa to 106 kPa and a relative humidity of 50 % ± 2 %.
For reference testing, a conditioning period shall be applied over 96 h ± 4 h by heating the products in a circulating air oven at
the rated temperature and a relative humidity not exceeding 20 %.
Revision: 04-Jul-13
Document Number: 26013
6
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKT1813
www.vishay.com
Vishay Roederstein
CHARACTERISTICS
PERMISSIBLE AC VOLTAGE VS. FREQUENCY
1000
Capacitance in μF
7
5
VRMS
VRMS
100
0.
15
3
3
0.
2
2
33
0.
47
10
22
7
5
15
10
4.
7
0.0
22
7
5
2.
2
0.0
47
0.4
7 0.2 0
2 .1
2.2 1
.0
3
2
2
400 VDC
63 VDC
1
102
2
3
5 7 103
2
5 7 104
3
2
5 7 105
f [Hz]
3
10
102
2
3
5 7 103
2
5 7 104
3
2
3
5 7 105
f [Hz]
1000
Capacitance in μF
7
5
0.0
68
VRMS
100
VRMS
0.0
06
8
100
1.
0
3
0.1
3
2
0.2
2
0.4
10
7
5
3
2
3
5 7 103
2
5 7 104
3
2
3
630 VDC
5 7 105
f [Hz]
1000
10
102
0.
00
1
0.
22
1.
0
2
15
100 VDC
0.
00
22
0.
1
3
4.7
47
0
0.
00
47
0.
03
3
7
5
1.0
2.2
2
0.
01
100
7
1
102
Capacitance in pF and μF
7
5
3
5
2
2
3
5 7 103
2
3
5 7 104
2
3
5 7 105
f [Hz]
1000
Capacitance in μF
7
5
VRMS
VRMS
Capacitance in μF
7
5
3
Capacitance in pF and μF
7
5
3
2
2
0.
01
100
7
5
5
3
2. 1
2 .0
2
0.
33
7
0.
15
2
3
04
22
7
0.
20
00
02
2
0.
01
0.
47
3
47
00
2
1000 VDC
250 VDC
10
102
0.
0.
7
5
04
4.
7
0.
1
100
0.
10
10
00
5 7 103
Revision: 04-Jul-13
2
3
5 7 104
2
3
5 7 105
f [Hz]
10
102
2
3
5 7 103
2
3
5 7 104
2
3
5 7 105
f [Hz]
Document Number: 26013
7
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKT1813
www.vishay.com
Vishay Roederstein
CHARACTERISTICS
1.2
Factor
ΔC = (%)
C
12
10
1.0
8
6
0.8
4
0.6
2
0
0.4
-2
-4
0.2
-6
0.0
- 60
- 20
20
-8
- 60
60 Tamb (°C) 100
- 40
- 20
0
20
40
60
80
100
Capacitance vs. Temperature ΔC/C = f (ϑ)
Nominal voltage (AC and DC) as a function of temperature
U = f(TA), TLL  TA  TUL
ΔC = (%)
C
2
140
Capacitance as a function of temperature
C/C = f(TA), TLL  TA  TUL
tan δ = 10-3
16
1
14
0
12
-1
10
-2
8
-3
6
-4
4
-5
-6
120
Tamb (°C)
2
102
2 3 5 7 104
Capacitance Change vs. Frequency ΔC = f (f)
C
2
3
5 7 103
2
3
0
- 60
5 7 105
f (Hz)
- 40
- 20
0
20
40
60
80
100
Dissipation Factor (1 kHz) vs. Temperature tan δ = f (ϑ)
Capacitance as function of frequency
C/C = f(f), 100 Hz  f  1 MHz
120
140
Tamb (°C)
Dissipation factor as function of temperature
tan /tan  = f(TA), TLL  TA  TUL
105
tan δ x 104
RC (s)
100
7
5
3
2
104
10
7
5
103
3
2
102
1
7
5
101
3
2
100
20
40
60
80
100
125
Tamb (°C)
Insulation resistance as a function of temperature
Ris = f(TA), TLL  TA  TUL
Revision: 04-Jul-13
0.1
102
2
3
5 7 103
2
3
5
7 104
2
3
Dissipation Factor vs. Frequency tan δ = f (f)
5 7 105
f (Hz)
Dissipation factor as a function of frequency
tan /tan  = f(f), 100 Hz  f  1 MHzL
Document Number: 26013
8
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKT1813
www.vishay.com
Vishay Roederstein
CHARACTERISTICS
ΔT (°C)
16
12
8
4
0
- 60
- 20
20
60 T
100
amb (°C)
Maximum allowed component temperature rise (T) as a function of the ambient temperature (Tamb)
HEAT CONDUCTIVITY (G) AS A FUNCTION OF (ORIGINAL) PITCH AND CAPACITOR BODY
THICKNESS IN mW/°C
Dmax.
(mm)
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10.0
10.5
11.0
11.5
12.0
12.5
13.0
13.5
14.0
14.5
15.0
15.5
16.0
16.5
17.0
17.5
18.0
18.5
19.0
20.0
20.5
21.0
Revision: 04-Jul-13
L = 11 mm
2
2
-
L = 14 mm
3
3
3
4
4
-
HEAT CONDUCTIVITY (mW/°C)
L = 19 mm
L = 26.5 mm
4
5
5
6
8
6
9
7
10
11
8
12
13
9
14
15
16
-
L = 31.5 mm
14
15
16
17
18
19
19
21
22
24
28
-
L = 41.5 mm
29
30
31
34
38
Document Number: 26013
9
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKT1813
www.vishay.com
Vishay Roederstein
POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function
of the free ambient temperature.
The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical Information Film
Capacitors”.
The component temperature rise (T) can be measured (see section “Measuring the component temperature” for more details)
or calculated by T = P/G:
• T = Component temperature rise (°C)
• P = Power dissipation of the component (mW)
• G = Heat conductivity of the component (mW/°C)
MEASURING THE COMPONENT TEMPERATURE
A thermocouple must be attached to the capacitor body as in:
Thermocouple
The temperature is measured in unloaded (Tamb) and maximum loaded condition (TC).
The temperature rise is given by T = TC - Tamb.
To avoid radiation or convection, the capacitor should be tested in a wind-free box.
APPLICATION NOTE AND LIMITING CONDITIONS
These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as
described hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic
interference suppression capacitors conforming the standards must be used.
To select the capacitor for a certain application, the following conditions must be checked:
1. The peak voltage (UP) shall not be greater than the rated DC voltage (URDC)
2. The peak-to-peak voltage (UP-P) shall not be greater than 22 x URAC to avoid the ionization inception level
3. The voltage peak slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by URdc and
divided by the applied voltage.
For all other pulses following equation must be fulfilled:
 T
dU 2
dU

2 x   ------- x dt  U RDC x  -------
 dt 
 dt  rated

0

T is the pulse duration.
The rated voltage pulse slope is valid for ambient temperatures up to 85 °C. For higher temperatures a derating factor of
3 % per K shall be applied.
4. The maximum component surface temperature rise must be lower than the limits (see figure “Max. allowed component
temperature rise”).
5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values
mentioned in the table “Heat Conductivity”.
6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected
with an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes
and surge voltages from the mains included).
Revision: 04-Jul-13
Document Number: 26013
10
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKT1813
www.vishay.com
Vishay Roederstein
VOLTAGE CONDITIONS FOR 6 ABOVE
Tamb  85 °C
85 °C < Tamb  100 °C
URAC
0.8 x URAC
Maximum temperature RMS-overvoltage (< 24 h)
1.25 x URAC
URAC
Maximum peak voltage (VO-P) (< 2 s)
1.6 x URDC
1.3 x URDC
ALLOWED VOLTAGES
Maximum continuous RMS voltage
Example
C = 3300 nF - 100 V used for the voltage signal shown in next figure.
UP-P = 80 V; UP = 70 V; T1 = 0.5 ms; T2 = 1 ms
The ambient temperature is 35 °C
Checking conditions:
1. The peak voltage UP = 70 V is lower than 100 VDC
2. The peak-to-peak voltage 80 V is lower than 22 x 63 VAC = 178 UP-P
3. The voltage pulse slope (dU/dt) = 80 V/500 μs = 0.16 V/μs
This is lower than 8 V/μs (see “Specific Reference Data” for each version)
4. The dissipated power is 60 mW as calculated with fourier terms
The temperature rise for Wmax. = 11.5 mm and pitch = 26.5 mm will be 60 mW/13 mW/°C = 4.6 °C
This is lower than 15 °C temperature rise at 35 °C, according figure “Maximum allowed component temperature rise”
5. Not applicable
6. Not applicable
Voltage Signal
Voltage
UP
UP-P
Time
T1
T2
Revision: 04-Jul-13
Document Number: 26013
11
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKT1813
www.vishay.com
Vishay Roederstein
INSPECTION REQUIREMENTS
General Notes
Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-2 and
Specific Reference Data”.
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C1A PART OF SAMPLE 
OF SUB-GROUP C1
4.1
Dimensions (detail)
As specified in Chapters “General data” of
this specification
4.3.1 Initial measurements
Capacitance
Tangent of loss angle:
For C  470 nF at 100 kHz or
for C > 470 nF at 10 kHz
4.3
Robustness of terminations
Tensile: Load 10 N; 10 s
Bending: Load 5 N; 4 x 90°
4.4
Resistance to soldering heat
Method: 1A
Solder bath: 280 °C ± 5 °C
Duration: 10 s
No visible damage
4.14 Component solvent resistance
Isopropylalcohol at room temperature
Method: 2
Immersion time: 5 min ± 0.5 min
Recovery time: Min. 1 h, max. 2 h
4.4.2 Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
|C/C|  2 % of the value measured initially
Tangent of loss angle
Increase of tan 
 0.005 for: C  100 nF or
 0.010 for: 100 nF < C  220 nF or
 0.015 for: 220 nF < C  470 nF and
 0.003 for: C > 470 nF
Compared to values measured in 4.3.1
SUB-GROUP C1B PART OF SAMPLE 
OF SUB-GROUP C1
4.6.1 Initial measurements
Capacitance
Tangent of loss angle:
For C  470 nF at 100 kHz or
for C > 470 nF at 10 kHz
4.6
A = - 55 °C
B = + 100 °C
5 cycles
Duration t = 30 min
Rapid change of temperature
Visual examination
4.7
Vibration
4.7.2 Final inspection
Revision: 04-Jul-13
No visible damage
Mounting: 
See section “Mounting” of this specification
Procedure B4
Frequency range: 10 Hz to 55 Hz
Amplitude: 0.75 mm or
Acceleration 98 m/s2
(whichever is less severe)
Total duration 6 h
Visual examination
No visible damage
Document Number: 26013
12
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKT1813
www.vishay.com
Vishay Roederstein
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C1B PART OF SAMPLE 
OF SUB-GROUP C1
4.9
Shock
Mounting:
See section “Mounting” of this specification
Pulse shape: Half sine
Acceleration: 490 m/s2
Duration of pulse: 11 ms
4.9.3
Final measurements
Visual examination
No visible damage
Capacitance
|C/C|  3 % of the value measured in 4.6.1
Tangent of loss angle
Increase of tan  
 0.005 for: C  100 nF or
 0.010 for: 100 nF < C  220 nF or
 0.015 for: 220 nF < C  470 nF and
 0.003 for: C > 470 nF
Compared to values measured in 4.6.1
Insulation resistance
As specified in section “Insulation
Resistance” of this specification
SUB-GROUP C1 COMBINED SAMPLE 
OF SPECIMENS OF SUB-GROUPS 
C1A AND C1B
4.10
Climatic sequence
4.10.2
Dry heat
4.10.3
Damp heat cyclic
Test Db, first cycle
4.10.4
Cold
4.10.6
Damp heat cyclic
Test Db, remaining cycles
4.10.6.2 Final measurements
Temperature: + 100 °C
Duration: 16 h
Temperature: - 55 °C
Duration: 2 h
Voltage proof = URDC for 1 min within 15 min
after removal from testchamber
No breakdown of flash-over
Visual examination
No visible damage
Legible marking
Capacitance
|C/C|  5 % of the value measured in 
4.4.2 or 4.9.3
Tangent of loss angle
Increase of tan 
 0.007 for: C  100 nF or
 0.010 for: 100 nF < C  220 nF or
 0.015 for: 220 nF < C  470 nF and
 0.005 for: C > 470 nF
Compared to values measured in
4.3.1 or 4.6.1
Insulation resistance
 50 % of values specified in section
“Insulation resistance” of this specification
SUB-GROUP C2
4.11
Damp heat steady state
56 days, 40 °C, 90 % to 95 % RH
4.11.1
Initial measurements
Capacitance
Tangent of loss angle at 1 kHz
Revision: 04-Jul-13
Document Number: 26013
13
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKT1813
www.vishay.com
Vishay Roederstein
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C2
4.11.3 Final measurements
Voltage proof = URDC for 1 min within 15 min
after removal from testchamber
No breakdown of flash-over
Visual examination
No visible damage
Legible marking
Capacitance
|C/C|  5 % of the value measured in 4.11.1
Tangent of loss angle
Increase of tan  0.005
Compared to values measured in 4.11.1
Insulation resistance
 50 % of values specified in section
“Insulation resistance” of this specification
SUB-GROUP C3
4.12
Endurance
Duration: 2000 h
1.25 x URDC at 85 °C
1.0 x URDC at 100 °C
4.12.1 Initial measurements
Capacitance
Tangent of loss angle:
For C  470 nF at 100 kHz or
for C > 470 nF at 10 kHz
4.12.5 Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
|C/C|  5 % compared to values measured
in 4.12.1
Tangent of loss angle
Increase of tan 
 0.005 for: C  100 nF or
 0.010 for: 100 nF < C  220 nF or
 0.015 for: 220 nF < C  470 nF and
 0.003 for: C > 470 nF
Compared to values measured in 4.12.1
Insulation resistance
 50 % of values specified in section
“Insulation resistance” of this specification
SUB-GROUP C4
4.13
Charge and discharge
10 000 cycles
Charged to URDC
Discharge resistance:

UR
R = ---------------------------------------------------C x 2.5 x  dU  dt  R


4.13.1 Initial measurements
Capacitance
Tangent of loss angle:
For C  470 nF at 100 kHz or
for C > 470 nF at 10 kHz
4.13.3 Final measurements
Capacitance
|C/C|  3 % compared to values measured
in 4.13.1
Tangent of loss angle
Increase of tan 
 0.005 for: C  100 nF or
 0.010 for: 100 nF < C  220 nF or
 0.015 for: 220 nF < C  470 nF and
 0.003 for: C > 470 nF
Compared to values measured in 4.13.1
Insulation resistance
 50 % of values specified in section
“Insulation resistance” of this specification
Revision: 04-Jul-13
Document Number: 26013
14
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000