MKP1839 HQ www.vishay.com Vishay Roederstein AC and Pulse Metallized Polypropylene Film Capacitors MKP Axial Type FEATURES • Supplied loose in box, taped on ammopack or reel available on request • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS High current and high pulse operations QUICK REFERENCE DATA Capacitance range (E12 series) 0.1 μF to 3.3 μF Capacitance tolerance ±5% Rated DC voltage 630 VDC, 850 VDC, 1250 VDC, 1600 VDC Rated AC voltage 300 VAC, 400 VAC, 425 VAC, 450 VAC Climatic testing class according to IEC 60068-1 55/110/56 Rated temperature 85 °C At 85 °C: UC = 1.0 UR At 110 °C: UC = 0.7 UR Maximum application temperature Reference standards IEC 60384-17 Dielectric Polypropylene film Electrodes Metallized Construction Series construction Encapsulation Plastic-wrapped, epoxy resin sealed. Flame retardant Leads Tinned wire Pull test on leads 20 N in direction of leads according to IEC 60068-2-21 Bent test on leads 2 bends through 90° with half of the force used in pull test Operation life > 300 000 h Failure rate < 5 FIT (40 °C and 0.5 x UR) Reliability Manufacturer’s logo; code for dielectric material; manufacturer’s type designation; C-code; rated voltage-code; tolerance-code; special n °C-value; tolerance; rated voltage; year and week; manufacturer’s location Marking Note • For more detailed data and test requirements, contact [email protected] DIMENSIONS in millimeters Ø dt Lmax. + 2.0 40.0 ± 5.0 Revision: 21-Dec-15 Lmax. 40.0 ± 5.0 Dmax. Document Number: 28162 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MKP1839 HQ www.vishay.com Vishay Roederstein COMPOSITION OF CATALOG NUMBER MULTIPLIER (nF) 0.1 2 1 3 10 4 100 SPECIAL LETTER FOR TAPED CAPACITANCE (numerically) Bulk Example: 468 = 680 nF 5 R Reel G Ammopack (1) Special HIGH QUALITY CAPACITOR TYPE MKP 1839 X XX 08 X VOLTAGE (VDC) HQ X TOLERANCE 63 = 630 V 4 ±5% 08 = 850 V 12 = 1250 V 13 = 1600 V Note (1) For detailed tape specifications refer to packaging information: www.vishay.com/doc?28139 or end of catalog SPECIFIC REFERENCE DATA DESCRIPTION Tangent of loss angle: VALUE 1 kHz 10 kHz 100 kHz 0.1 μF < C 0.47 μF 3 x 10-4 5 x 10-4 40 x 10-4 0.47 μF < C 1 μF 3 x 10-4 8 x 10-4 60 x 10-4 1 μF < C 3.3 μF 3x 15 x 10-4 10-4 - Rated voltage pulse slope (dU/dt)R at URDC 630 VDC 850 VDC 1250 VDC 1600 VDC 500 V/μs 1000 V/μs 1000 V/μs 1000 V/μs UP-P peak-to-peak voltage 700 V 1130 V 1400 V 1600 V 2000 V 2560 V R between leads, for C 0.33 μF at 500 V, 1 min > 100 G RC between leads, for C > 0.33 μF at 500 V, 1 min > 30 000 s R between interconnecting and wrapped film at 500 V, 1 min > 100 G Withstanding (DC) voltage (cut off current 10 mA), rise time 100 V/s Withstanding (DC) voltage between leads and wrapped film (1.4 x URAC + 2000) Maximum application temperature Revision: 21-Dec-15 1008 V 1360 V 1 min 2840 V, 1 min 110 °C Document Number: 28162 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MKP1839 HQ www.vishay.com Vishay Roederstein ELECTRICAL DATA AND ORDERING INFORMATION URDC (V) 630 850 1250 1600 CAP. (μF) VOLTAGE CODE 0.10 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.00 1.50 2.20 3.30 0.10 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.00 1.50 0.10 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 0.82 1.00 0.10 0.15 0.18 0.22 0.27 0.33 0.39 0.47 0.56 0.68 63 08 12 13 VAC 300 400 425 450 DIMENSIONS (mm) Lmax. Dmax. 7 26.5 8 26.5 8.5 26.5 9.5 26.5 10 26.5 11 26.5 10.5 31.5 11 31.5 12 31.5 13 31.5 14 31.5 16 31.5 19 31.5 23 31.5 28 31.5 8.5 31.5 10 31.5 11 31.5 11.5 31.5 13 31.5 14 31.5 15 31.5 16.5 31.5 15 31.5 16.5 31.5 18 31.5 19.5 31.5 24 31.5 8.5 31.5 10 31.5 11 31.5 11.5 31.5 13 31.5 14 31.5 15 31.5 16.5 31.5 18 31.5 20 31.5 21.5 31.5 23.5 31.5 12 31.5 14 31.5 15 31.5 16.5 31.5 17.5 31.5 20 31.5 21.5 31.5 23.5 31.5 25.5 31.5 28 31.5 dt ± 0.08 mm (mm) 0.8 1.0 0.8 1.0 0.8 1.0 0.8 1.0 MASS (g) SPQ (1) (pieces) 0.9 1.2 1.4 1.6 1.9 2.3 2.6 3.0 3.5 4.2 5.1 6.1 9.0 13.1 19.5 1.6 2.3 2.7 3.2 3.9 4.6 5.4 6.5 5.4 6.5 7.8 9.4 13.9 1.6 2.3 2.7 3.2 3.9 4.6 5.4 6.5 7.7 9.2 11.1 13.4 2.7 3.9 4.6 5.5 6.7 8.1 9.5 11.3 13.4 16.2 2000 1750 1500 1250 1000 900 900 750 650 500 1000 900 600 450 300 1500 1000 850 750 1000 1000 1000 1000 1000 1000 750 600 400 1500 1000 1000 800 650 500 1000 900 750 600 500 400 1000 600 500 500 900 750 600 500 400 350 Note (1) SPQ = Standard Packing Quantity Revision: 21-Dec-15 Document Number: 28162 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MKP1839 HQ www.vishay.com Vishay Roederstein MOUNTING Normal Use The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for mounting in printed-circuit boards by means of automatic insertion machines. Specific Method of Mounting to Withstand Vibration and Shock In order to withstand vibration and shock tests, it must be ensured that the capacitor body is in good contact with the printed-circuit board. • For L 19 mm capacitors shall be mechanically fixed by the leads • For larger pitches the capacitors shall be mounted in the same way and the body clamped • The maximum diameter and length of the capacitors are specified in the dimensions table • Eccentricity as shown in the drawing below: 1 mm Soldering Conditions For general soldering conditions and wave soldering profile, we refer to application note: “Soldering Guidelines for Film Capacitors”: www.vishay.com/doc?28171 Storage Temperature Tstg = -25 °C to +35 °C with RH maximum 75 % without condensation Ratings and Characteristics Reference Conditions Unless otherwise specified, all electrical values apply to an ambient free air temperature of 23 °C ± 1 °C, an atmospheric pressure of 86 kPa to 106 kPa and a relative humidity of 50 % ± 2 %. For reference testing, a conditioning period shall be applied over 96 h ± 4 h by heating the products in a circulating air oven at the rated temperature and a relative humidity not exceeding 20 %. Revision: 21-Dec-15 Document Number: 28162 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MKP1839 HQ www.vishay.com Vishay Roederstein CHARACTERISTICS 4 Dissipation Factor x 1-4 ΔC/C (%) 103 2 102 0 3.3 µF 1.0 µF 0.1 µF -2 101 -4 -6 - 60 - 40 - 20 0 20 40 60 80 100 Tamb (°C) 100 120 102 Capacitance as a function of ambient temperature (typical curve) 103 104 105 f (Hz) 106 Tangent of loss angle as a function of frequency (typical curve) Impedance (Ω) Factor 1.2 103 Capacitance in µF 102 101 100 1 0.1 µF 0.8 0.22 µF 0.47 µF 1.0 µF 0.6 3.3 µF 0.4 10-1 0.2 10-2 10-3 104 10 5 10 6 7 10 f (Hz) 10 0 - 60 8 20 60 100 Tamb (°C) 103 103 VRMS (V) Max. DC and AC voltage as a function of temperature VRMS (V) Impedance as a function of frequency (typical curve) - 20 102 102 0.1 µF 0.22 µF 0.47 µF 0.1 µF 0.22 µF 0.47 µF 1.0 µF 3.3 µF 101 Tamb ≤ 85 °C, 630 VDC 100 102 103 104 85 °C < Tamb ≤ 110 °C, 630 VDC 105 106 f (Hz) Max. RMS voltage (sinewave) as a function of frequency Revision: 21-Dec-15 1.0 µF 3.3 µF 101 107 100 102 103 104 105 106 f (Hz) 107 Max. RMS voltage (sinewave) as a function of frequency Document Number: 28162 5 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MKP1839 HQ www.vishay.com 103 103 VRMS (V) VRMS (V) Vishay Roederstein 102 102 0.1 µF 0.22 µF 0.47 µF 0.1 µF 0.22 µF 0.47 µF 1.0 µF 101 1.0 µF 101 Tamb ≤ 85 °C, 850 VDC 100 102 3 10 85 °C < Tamb ≤ 110 °C, 850 VDC 4 10 5 10 6 10 f (Hz) 10 7 100 102 103 103 VRMS (V) 102 102 0.1 µF 0.22 µF 0.47 µF 1.0 µF 101 3 10 105 106 f (Hz) 107 0.1 µF 0.22 µF 0.47 µF 1.0 µF 101 Tamb ≤ 85 °C, 1250 VDC 100 102 104 Max. RMS voltage (sinewave) as a function of frequency VRMS (V) Max. RMS voltage (sinewave) as a function of frequency 103 85 °C < Tamb ≤ 110 °C, 1250 VDC 4 10 5 10 6 10 f (Hz) 10 7 100 102 104 105 106 f (Hz) 107 103 103 VRMS (V) Max. RMS voltage (sinewave) as a function of frequency VRMS (V) Max. RMS voltage (sinewave) as a function of frequency 103 102 102 0.1 µF 0.22 µF 0.47 µF 0.1 µF 0.22 µF 0.47 µF 101 101 Tamb ≤ 85 °C, 1600 VDC 100 102 103 104 105 106 f (Hz) Max. RMS voltage (sinewave) as a function of frequency Revision: 21-Dec-15 107 100 102 85 °C < Tamb ≤ 110 °C, 1600 VDC 103 104 105 106 f (Hz) 107 Max. RMS voltage (sinewave) as a function of frequency Document Number: 28162 6 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MKP1839 HQ www.vishay.com Vishay Roederstein 106 RC (s) ΔT (°C) 12 10 8 6 105 4 2 104 0 30 60 90 Tamb (°C) 0 - 60 120 Insulation resistance as a function of ambient temperature (typical curve) - 20 20 60 Tamb (°C) 100 Max. allowed component rise (T) as a function of the ambient temperature (Tamb) HEAT CONDUCTIVITY (G) AS A FUNCTION OF CAPACITOR BODY THICKNESS IN mW/°C HEAT CONDUCTIVITY (mW/°C) DIAMETER (mm) PITCH 26.5 mm 7.0 8 - 8.0 10 - 8.5 11 12 9.5 12 - 10.0 13 15 10.5 - 16 11.0 15 17 11.5 - 18 12.0 - 19 12.5 - 20 13.0 - 21 13.5 - 22 14.0 - 23 15.0 - 25 16.0 - 28 16.5 - 29 18.0 - 32 19.0 - 34 19.5 - 36 20.0 - 37 21.5 - 40 23.0 - 44 23.5 - 45 24.0 - 47 25.5 - 51 28.0 - 57 Revision: 21-Dec-15 PITCH 31.5 mm Document Number: 28162 7 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MKP1839 HQ www.vishay.com Vishay Roederstein POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function of the free air ambient temperature. The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical Information Film Capacitors with the typical tgd of the curves”. The component temperature rise (T) can be measured (see section “Measuring the component temperature” for more details) or calculated by T = P/G: • T = Component temperature rise (°C) • P = Power dissipation of the component (mW) • G = Heat conductivity of the component (mW/°C) MEASURING THE COMPONENT TEMPERATURE A thermocouple must be attached to the capacitor body as in: Thermocouple The temperature is measured in unloaded (Tamb) and maximum loaded condition (TC). The temperature rise is given by T = TC - Tamb. To avoid radiation or convection, the capacitor should be tested in a wind-free. APPLICATION NOTE AND LIMITING CONDITIONS These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as described hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic interference suppression capacitors conforming the standards must be used. To select the capacitor for a certain application, the following conditions must be checked: 1. The peak voltage (UP) shall not be greater than the rated DC voltage (URDC). 2. The peak-to-peak voltage (UP-P) shall not be greater than the maximum (UP-P) to avoid the ionization inception level. 3. The voltage pulse slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by URDC and divided by the applied voltage. For all other pulses following equation must be fulfilled: T dU 2 dU 2 x ------- x dt U RDC x ------- dt dt rated 0 T is the pulse duration. 4. The maximum component surface temperature rise must be lower than the limits (see figure Max. Allowed Component Temperature Rise). 5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values mentioned in the table “Heat conductivity”. 6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected with an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes and surge voltages from the mains included). Revision: 21-Dec-15 Document Number: 28162 8 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MKP1839 HQ www.vishay.com Vishay Roederstein VOLTAGE CONDITIONS FOR 6 ABOVE Tamb 85 °C 85 °C < Tamb 110 °C URAC See “Maximum AC voltage as a function of temperature par. characteristics” Maximum temporary RMS-overvoltage (< 24 h) 1.25 x URAC 0.875 x URAC Maximum peak voltage (VO-P) (< 2 s) 1.6 x URDC 1.1 x URDC ALLOWED VOLTAGES Maximum continuous RMS voltage INSPECTION REQUIREMENTS General Notes Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-17 and Specific Reference Data”. GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1A PART OF SAMPLE OF SUB-GROUP C1 4.1 Dimensions (detail) As specified in chapter “General Data” of this specification 4.3.1 Initial measurements Capacitance Tangent of loss angle at 100 kHz 4.3 Robustness of terminations Tensile: load 30 N; 10 s Bending: load 15 N; 90° 4.4 Resistance to soldering heat No pre-drying Method: 1A Solder bath: 280 °C ± 5 °C Duration: 10 s 4.4.2 Final measurements 4.14 Solvent resistance of the marking No visible damage Visual examination No visible damage Legible marking Capacitance |C/C| 2 % of the value measured initially Tangent of loss angle Increase of tan : for C 470 nF 0.001 (10 x 10-4) for C > 470 nF 0.0015 (15 x 10-4) Compared to values measured initially Insulation resistance 50 % of values specified in section “Insulation Resistance” of this specification Isopropylalcohol at room temperature Method: 1 Rubbing material: cotton wool Immersion time: 5 min ± 0.5 min No visible damage Legible marking SUB-GROUP C1B PART OF SAMPLE OF SUB-GROUP C1 4.6.1 Initial measurements Capacitance Tangent of loss angle at 100 kHz 4.6 qA = -55 °C qB = +110 °C 5 cycles Duration t = 30 min Rapid change of temperature Visual examination Revision: 21-Dec-15 No visible damage Document Number: 28162 9 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MKP1839 HQ www.vishay.com Vishay Roederstein GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS SUB-GROUP C1B PART OF SAMPLE OF SUB-GROUP C1 4.7 Vibration Mounting: see section “Mounting” of this specification Procedure B4 Frequency range: 10 Hz to 55 Hz Amplitude: 0.75 mm or Acceleration 98 m/s2 (whichever is less severe) Total duration 6 h 4.7.2 Final inspection Visual examination 4.9 Shock Mounting: see section “Mounting” for more information Pulse shape: half sine Acceleration: 490 m/s2 Duration of pulse: 11 ms 4.9.3 Final measurements Visual examination No visible damage Capacitance |C/C| 2 % of the value measured initally Tangent of loss angle Increase of tan : for C 470 nF 0.001 (10 x 10-4) for C > 470 nF 0.0015 (15 x 10-4) Compared to values measured initially Insulation resistance 50 % of values specified in section “Insulation Resistance” of this specification No visible damage SUB-GROUP C1 COMBINED SAMPLE OF SPECIMENS OF SUB-GROUPS C1A AND C1B 4.10 Climatic sequence 4.10.2 Dry heat 4.10.3 Damp heat cyclic Test Db, first cycle 4.10.4 Cold 4.10.6 Damp heat cyclic Test Db, remaining cycles 4.10.6.2 Final measurements Revision: 21-Dec-15 Temperature: 110 °C Duration: 16 h Temperature: -55 °C Duration: 2 h Voltage proof = URDC for 1 min within 15 min after removal from testchambers No breakdown or flashover Visual examination No visible damage Legible marking Capacitance |C/C| 3 % of the value measured initially Tangent of loss angle Increase of tan : for C 470 nF 0.001 (10 x 10-4) for C > 470 nF 0.0015 (15 x 10-4) Compared to values measured in 4.3.1 or 4.6.1 as applicable Insulation resistance 50 % of values specified in section “Insulation Resistance” of this specification Document Number: 28162 10 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 MKP1839 HQ www.vishay.com Vishay Roederstein GROUP C INSPECTION REQUIREMENTS SUB-CLAUSE NUMBER AND TEST SUB-GROUP C2 4.11 Damp heat steady state Capacitance 4.11.1 Tangent of loss angle at 1 kHz 4.11.3 Initial measurements Final measurements SUB-GROUP C3 A 4.12.1 Endurance test at 50 Hz alternative voltage CONDITIONS PERFORMANCE REQUIREMENTS Visual examination No visible damage Legible marking Voltage proof = URDC for 1 min within 15 min after removal from testchamber No breakdown or flashover Capacitance |C/C| 3 % of the value measured in 4.11.1. Tangent of loss angle Increase of tan : for C 470 nF 0.001 (10 x 10-4) for C > 470 nF 0.0015 (15 x 10-4) Compared to values measured in 4.11.1 Insulation resistance 50 % of values specified in section “Insulation Resistance” of this specification Duration: 2000 h 1.0 x URAC at 85 °C 0.875 x URAC at 110 °C 4.12.1.1 Initial measurements Capacitance Tangent of loss angle at 100 kHz 4.12.1.3 Final measurements Visual examination No visible damage Legible marking Capacitance |C/C| 5 % compared to values measured in 4.12.1.1 Tangent of loss angle Increase of tan : for C 470 nF 0.001 (10 x 10-4) for C > 470 nF 0.0015 (15 x 10-4) Compared to values measured in 4.12.1.1 Insulation resistance 50 % of values specified in section “Insulation Resistance” of this specification Capacitance Capacitance at -55 °C Capacitance at 20 °C Capacitance at 110 °C For -55 °C to 20 °C 0 % |C/C| 2.75 % or for 20 °C to 110 °C: -5.5 % |C/C| 0 % As specified in section “Capacitance” of this specification SUB-GROUP C4 4.2.6 Temperature characteristics Initial measurement Intermediate measurements 4.13 Charge and discharge 10 000 cycles Charged to URDC Discharge resistance: U n V DC R = -----------------------------------------2.5 x C dU dt 4.13.1 Initial measurements Capacitance Tangent of loss angle at 100 kHz 4.13.3 Final measurements Capacitance |C/C| 3 % of the value measured in 4.13.1 Tangent of loss angle Increase of tan : for C 470 nF 0.001 (10 x 10-4) for C > 470 nF 0.0015 (15 x 10-4) Compared to values measured in 4.13.1 Insulation resistance 50 % of values specified in section “Insulation Resistance” of this specification Revision: 21-Dec-15 Document Number: 28162 11 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000