Datasheet

XC7
DIN Sequence Connectors
An improved DIN-standard Sequence
Connector
■ Allows power line to daughter board connection
first and removal last.
■ Used the same way as regular DIN connectors.
Dimensions are those of DIN B-type and C-type
connectors. Mated length is 4 mm. All contacts
are sequential contacts, an improvement on standard connectors.
■ Sockets are equipped with 1-mm long sequential
contacts. Sockets can be stacked up to 2 levels,
and Plugs can be stacked up to 3 levels.
■ Uses a double-sided contact design. Gold/palla-
dium plating has an insertion durability of 5,000
cycles.
Note:
Cannot be mated with XC5 and XC6 Series.
RoHS Compliant
■ Connectors
Model
Appearance
Page
XC7A
XC7B
XC7C
XC7D
Plug with
right-angle
terminals
Socket with
straight terminals
Plug with
right-angle
terminals
Socket with
straight terminals
2
3
4
■ Ratings and Characteristics
5
■ Materials and Finish
Rated current
2A
Item
Plugs
Rated voltage
300 VAC
Housings
Contact resistance
20 mΩ max. (at 20 mV, 100 mA max.)
Fiber-glass reinforced PBT resin (UL94 V0)/gray
Contacts Mating
end
Brass/nickel base, Phosphor-bronze/
gold/palladium plat- nickel base, gold/
ing
palladium plating
Insulation resistance 106 MΩ min. (at 100 VDC)
Dielectric strength
1,000 VAC for 1 min (leakage current:
1 mA max.)
Total insertion force
1 N max. per contact
Removal force
0.2 N min. (with test gauge, t = 0.56 mm)
Insertion durability
5,000 times
Ambient operating
temperature
−55 to 125°C (with no icing at low
temperature)
Terminal
Brass/nickel base,
gold flash plating
Sockets
Phosphor-bronze/
nickel base, gold
flash plating
1
XC7A Double-row Plugs
■ Dimensions
(unit: mm)
XC7A-@@42-@@@@
(With right-angle DIP terminals)
Two, 2.8 dia.
*Sequential contacts
Mounting holes (bottom view)
0.8 +0.1
dia.
0
Two, 2.8 dia.
Dimensions
No. of
contacts
64
Dimensions (mm)
A
B
93.8
88.0
C
78.74
D
E
88.9
83.9
90
126.8
121.0
111.76
121.9
117.0
118.2
100
139.5
133.7
124.46
134.6
129.7
130.9
■ Ordering Information
Appearance
No. of contacts
Terminal type
64
90
100
2
Sequential contact position
None
Right-angle DIP
terminals
F
85.2
Model
XC7A-6442
All
XC7A-6442-N001
None
XC7A-9042
All
XC7A-9042-N001
None
XC7A-0142
All
XC7A-0142-N001
DIN Sequence Connectors XC7
XC7B Double-row Sockets
■ Dimensions
(unit: mm)
XC7B-@@41-@@@@
(With straight DIP terminals)
Two, 2.8 dia.
*Sequential contacts
Mounting holes (bottom view)
0.8 +0.1
dia.
0
Two, 2.8 dia.
Dimensions
No. of
contacts
64
Dimensions (mm)
A
B
94.8
85.0
C
78.74
D
E
90.0
83.0
90
127.8
118.0
111.76
123.0
116.0
100
140.5
130.7
124.46
135.7
128.7
■ Ordering Information
Appearance
No. of contacts
Terminal type
64
90
100
Straight DIP
terminals
Sequential contact position
Model
a, b: 1 to 4
a, b: 26 to 32
XC7B-6441-N003
All
XC7B-6441-N001
a, b: 1 to 4
a, b: 39 to 45
XC7B-9041-N003
All
XC7B-9041-N001
a, b: 1 to 4
a, b: 44 to 50
XC7B-0141-N003
All
XC7B-0141-N001
DIN Sequence Connectors
XC7
3
XC7C Triple-row Plugs
■ Dimensions
(unit: mm)
XC7C-9642-@@@@
(With right-angle DIP terminals)
Two, 2.8 dia.
*Sequential contacts
Mounting holes (bottom view)
96, 0.8 +0.1
dia.
0
Two, 2.8 dia.
■ Ordering Information
Appearance
No. of
contacts
96
4
Terminal type
Sequential contact
position
Right-angle DIP ter- All
minals
None
DIN Sequence Connectors XC7
Model
XC7C-9642-N001
XC7C-9642
XC7D Triple-row Sockets
■ Dimensions
(unit: mm)
XC7D-9641-@@@@
(With straight DIP terminals)
Two, 2.8 dia.
*Sequential contact
Mounting holes (bottom view)
96, 0.8 +0.1
dia.
0
Two, 2.8 dia.
■ Ordering Information
Appearance
No. of
contacts
96
Terminal type
Straight DIP
terminals
Sequential contact
position
Model
All
XC7D-9641-N001
a1, a32
XC7D-9641-N002
DIN Sequence Connectors
XC7
5
■ Mating Diagrams (unit: mm)
Double-row Connectors
Triple-row Connectors
Plug
XC7C
Plug
XC7A
Socket
XC7D
Socket
XC7B
■ Mates with
Standard DIN
Connectors
• Dimensions are the same as those of
standard DIN connectors XC5.
• The sequential contacts on the Socket
and Plug are 1 mm long, so they cannot
be interchanged with DIN Connectors.
Use as a Socket/Plug pair.
■ Precautions
Correct Use
Automated soldering
Dimensions after Mounting
Use masking tape to mask the Right-angle
Connectors before automated soldering.
• Mounting dimensions for all Connectors
should be as shown in the following diagram.
• The allowable margins for mating the Connectors are shown below.
Daughter board
Plug
0.8 mm max.
Masking tape
(Recommended tape: 3M Sumitomo #214)
Automated Soldering
Conditions (Jet Flow)
1. Soldering temperature: 250±5°C
2. Continuous soldering time: Within 5±1 s
Mother board
α: 3.55 mm
The distance between the center line of the
mounting holes on the mother board and
the daughter board. (This center line is
shifted 0.3 mm toward row a from row b.)
β: 2.54 mm
The distance between the mounting holes
on the daughter board and row a.
γ: 5.3 mm
The distance between the edge of the
daughter board and row a.
δ: 12.4 to 14.2 mm
To insure reliability, be sure to keep the
Connectors within these dimensions when
mounting.
6
DIN Sequence Connectors XC7
0.8 mm
max.
Socket
• Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product.
• Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad
systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious
influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or
equipment, and be sure to provide the system or equipment with double safety mechanisms.
Note: Do not use this document to operate the Unit.
OMRON Corporation
Electronic and Mechanical Components Company
Contact: www.omron.com/ecb
Cat. No. G054-E1-02
1014(0412)(O)