Datenblatt

HFXO OSCILLATOR
220 kHz to 100 MHz
High Precision & High Shock, Low Profile Miniature
Surface Mount Crystal Oscillator
DESCRIPTION
Statek’s high shock HFXO oscillators, available in tight
frequency tolerances, consist of a Statek miniature quartz
crystal and a CMOS/TTL compatible hybrid circuit in a
ceramic package. Each crystal used in the HFXO oscillator is
pre-qualified before assembly through electrical tests and
characterization over temperature.
FEATURES
Mechanical shock survivability of 75,000 g up to 50 MHz
Tight frequency tolerance
Low acceleration sensitivity
Low aging (Double Hermetic Seal)
DIMENSIONS
Low jitter
Optional Output Enable/Disable with Tri-State
Low EMI emission
Full military testing to MIL-PRF-55310 available
Low power consumption
APPLICATIONS
Military & Aerospace
Smart Munitions
Cockpit Systems
Navigation
Industrial, Computer & Communications
Industrial Controls
Instrumentation
Down-hole Drilling
SUGGESTED LAND PATTERN
0.070 (1.78)
0.067 (1.70)
0.065 (1.65)
TYPICAL
MAXIMUM
DIM
inches
mm
inches
mm
A
0.256
6.50
0.263
6.68
B
0.197
5.00
0.204
5.18
0.065
C (SM1)
C (SM3/SM5) 0.069
1.65
1.75
0.068
0.075
1.73
1.91
D
0.055
1.40
0.065
1.65
E
0.060
1.52
0.070
1.78
PIN CONNECTIONS
1. Enable/Disable (E or T) or not connected (N)
0.201 (5.11)
0.136 (3.45)
2. Ground
3. Output
4. VDD
0.137 (3.48)
GRID
PLACEMENT
COURTYARD
10189 Rev C
IS O
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
YS
90
01
TEM
C ERT I F I C
AT
N
IO
S
inches (mm)
ABSOLUTE MAXIMUM RATINGS
SPECIFICATIONS
Specifications are typical at 25 C unless otherwise noted.
Specifications are subject to change without notice. Tighter
specifications available. Please contact factory.
Supply Voltage VDD
Storage Temperature
Maximum Process Temperature
Supply Voltages1
Calibration Tolerance
Frequency Stability
Over Temperature2
*The supply voltage range is -0.5 V to +4.0 V for some products. Contact Factory.
O
0.9 V to 5.0 V
± 10 ppm and up
± 10 ppm for Commercial
± 20 ppm for Industrial
± 40 ppm for Military
Total Frequency3
± 15 ppm and up for Commercial
Tolerance
± 20 ppm and up for Industrial
± 50 ppm and up for Military
4
Output Load (CMOS)
15 pF
Start-up Time
5 ms MAX
Rise/Fall Time
10 ns MAX
5
Duty Cycle
40% MIN, 60% MAX
Aging, first year
5 ppm
6
Shock, survival
0.5 ms, 1/2 sine up to 75,000 g
Vibration, survival
20 g, 10-2,000 Hz swept sine
Operating Temp Ranges7 -10OC to +70OC (Commercial)
-40OC to +85OC (Industrial)
-55OC to + 125OC (Military)
ENABLE/DISABLE OPTIONS (E/T/N)
Statek offers three enable/disable options: E, T, and N.
Both the E-version and T-version have Tri-State outputs and
differ in whether the oscillator continues to run internally
when the output is put into the high Z state: it stops in the
E-version and continues to run in the T-version. So, the Eversion offers very low current consumption when the
oscillator is disabled and the T-version offers very fast output
recovery when the oscillator is re-enabled. The N-version
does not have PIN 1 connected internally and so has no
enable/disable capability. The following table summarizes the
three options.
COMPARISON OF
ENABLE/DISABLE OPTIONS E AND T
E
T8
When enabled (PIN 1 is high*)
1. Not all frequencies are available in certain voltages. Contact factory for details.
2. Does not include calibration tolerance
3. Frequency over temperature relative to nominal frequency.
4. Higher CMOS loads available. Contact factory.
5. Tighter Duty Cycles available. Contact factory.
Output
Freq. output
Freq. output
Oscillator
Oscillates
Oscillates
Current consumption
Normal
Normal
Output
High Z state
High Z state
Oscillator
Stops
Oscillates
Current consumption
Very low
Lower than normal
When disabled (PIN 1 is low)
6. 5000 g maximum available for frequencies above 50 MHz.
7. Higher temp available (up to 200 C). Contact factory.
O
8. The T-version is not available for all frequencies. Contact factory.
Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load.
When re-enabled (PIN 1 changes from low to high)
PACKAGING OPTIONS
HFXO
-0.5 V to 7.0 V*
-55OC to +125OC
260OC for 20 seconds
Output recovery
-Tray Pack
-16mm tape, 7” or 13” reels
Delayed
Immediate
* When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
(Reference tape and reel data sheet 10109)
HOW TO ORDER HFXO SURFACE MOUNT CRYSTAL OSCILLATORS
HFXO
3
Supply Voltage
9 = 0.9V
1 = 1.8V
2 = 2.5V
3 = 3.0V
4 = 3.3V
5 = 5.0V
D
Shock Level
A = 5,000 g
B = 10,000 g
C = 20,000 g
D = 30,000 g
F = 50,000 g
G = 75,000 g
S
Blank = Standard
S = Special or
custom
T
Enable/Disable
Option
E, T, or N
SM3
Termination
Blank = SM1
= Gold Plated (Pb Free)
SM3 = Solder Dipped
SM5 = Solder Dipped (Pb Free)
20.0M ,
Frequency
K = kHz
M = MHz
30
/
Calibration
Tolerance
@ 250C
(in ppm)
50
/
Frequency
Stability over
Temp.Range
(in ppm)
OR
/
Note: The HFXO oscillator with SM1 or SM5
termination is Pb free. The HFXO oscillator with
SM3 termination contains Pb.
/
100
Total
Frequency
Tolerance
(in ppm)
/
I
/
Temperature Range:
C = -10OC to +70OC
I = -40OC to +85OC
M = -55OC to +125OC
S = Customer Specified
I
Temperature Range:
C = -10OC to +70OC
I = -40OC to +85OC
M = -55OC to +125OC
S = Customer Specified
IS O
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
90
01
TEM
C ERT I F I C
AT
N
IO
S
10189 Rev C
YS