Data Sheet - Statek Corporation

CXOM OSCILLATOR
200 kHz to 200 MHz
Low Profile Miniature Surface Mount
Crystal Oscillator
DESCRIPTION
Statek’s surface-mount CXOM oscillators consist of a Statek
miniature quartz crystal and a CMOS/TTL compatible hybrid
circuit in a low-profile ceramic package with an extremely
small footprint.
GM
M
4.19
FEATURES
Designed for surface mount applications using infrared,
vapor phase, or epoxy mount techniques
CMOS and TTL compatible
Low power consumption
Optional Output Enable/Disable with Tri-State
Low EMI emission
DIMENSIONS
High shock resistance
Full military testing available
D
Hermetically sealed ceramic package
APPLICATIONS
2
A
TOP
3
BOTTOM
Military & Aerospace
1
4
Smart Munitions
D
Cockpit Systems
B
Navigation
E
C
Industrial, Computer & Communications
Industrial Controls
TYPICAL
Instrumentation
Microprocessor Clocks
Medical
Infusion Pumps
SUGGESTED LAND PATTERN
MAXIMUM
DIM
inches
mm
inches
mm
A
0.256
6.50
0.263
6.68
B
0.197
5.00
0.204
5.18
0.051
C (SM1)
C (SM3/SM5) 0.055
1.30
1.40
0.055
0.063
1.40
1.60
D
0.055
1.40
0.065
1.65
E
0.060
1.52
0.070
1.78
0.070 (1.78)
0.067 (1.70)
0.065 (1.65)
PIN CONNECTIONS
1. Enable/Disable (E or T) or not connected (N)
2. Ground
0.201 (5.11)
0.136 (3.45)
3. Output
4. VDD
0.137 (3.48)
GRID
PLACEMENT
COURTYARD
10116 Rev G
IS O
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
YS
90
01
TEM
C ERT I F I C
AT
N
IO
S
inches (mm)
ABSOLUTE MAXIMUM RATINGS
SPECIFICATIONS
Supply Voltage VDD
Storage Temperature
Maximum Process Temperature
Specifications are typical at 25 C unless otherwise noted.
Specifications are subject to change without notice. Tighter
specifications available. Please contact factory.
O
Supply Voltages1
Frequency Range2
0.9 V to 5.0 V ± 10%
200 kHz to 200 MHz
Calibration Tolerance3
± 100 ppm
Frequency Stability
Over Temperature4
Output Load (CMOS)5
Start-up Time
Rise/Fall Time
± 50 ppm for Commercial
± 100 ppm for Industrial
± 100 ppm for Military
10 MHz
4 mA
24 MHz
8 mA
30 MHz
10 mA
40 MHz
12 mA
50 MHz
14 mA
15 pF
5 ms MAX
6 ns MAX
Duty Cycle
40% MIN, 60% MAX
Supply Current (Typical)
*The supply voltage range is -0.5 V to +4.0 V for some products. Contact Factory.
ENABLE/DISABLE OPTIONS (E/T/N)
Statek offers three enable/disable options: E, T, and N.
Both the E-version and T-version have Tri-State outputs and
differ in whether the oscillator continues to run internally
when the output is put into the high Z state: it stops in the
E-version and continues to run in the T-version. So, the Eversion offers very low current consumption when the
oscillator is disabled and the T-version offers very fast output
recovery when the oscillator is re-enabled. The N-version
does not have PIN 1 connected internally and so has no
enable/disable capability. The following table summarizes
the three options.
COMPARISON OF
ENABLE/DISABLE OPTIONS E AND T
Aging, first year
10 ppm MAX
Shock, survival
3,000 g, 0.3 ms, 1/2 sine
Vibration, survival7
20 g, 10-2,000 Hz swept sine
6
-0.5 V to 7.0 V*
-55OC to +125OC
260OC for 20 seconds
E
T
When enabled (PIN 1 is high*)
Operating Temp Ranges -10OC to +70OC (Commercial)
-40OC to +85OC (Industrial)
-55OC to +125OC (Military)
1. Voltages available: 0.9 V, 1.8 V, 2.5 V, 3.0 V, 3.3 V, 5.0 V. For 3.3 V, see the
CXO3M data sheet (10126). For others, contact factory.
2. Maximum available frequency for the 5V Version of this oscillator is 160 MHz.
Contact Factory
3. Other tolerances available.
4. Does not include calibration tolerance. Other tolerances available.
5. Higher CMOS loads and TTL loads available. Contact factory.
6. Higher shock version available. Contact factory about CXOMHG.
7. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also
available.
Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF
load.
Output
Freq. output
Freq. output
Oscillator
Oscillates
Oscillates
Current consumption
Normal
Normal
Output
High Z state
High Z state
Oscillator
Stops
Oscillates
Current consumption
Very low
Lower than normal
When disabled (PIN 1 is low)
When re-enabled (PIN 1 changes from low to high)
Output recovery
PACKAGING OPTIONS
Delayed
Immediate
* When PIN 1 is allowed to float, it is held high by an internal pull-up resistor.
CXOM - Tray Pack
- 16mm tape, 7˝ or 13˝ reels
Per EIA 418 (see Tape and Reel data sheet 10109)
HOW TO ORDER CXOM SURFACE MOUNT CRYSTAL OSCILLATORS
CXOM
S
Enable/Disable
Option
E, T*, or N
SM3
32.0M
Terminations
Blank = SM1
= Gold Plated
SM3 = Solder Dipped
SM5 = Solder Dipped
(Lead Free)
Frequency
K = kHz
M = MHz
*The T-version is not available in all frequencies
and voltages. Contact factory.
,
100
Calibration
Tolerance
@ 250C
(in ppm)
/
100
/
Frequency
Stability over
Temp.Range
(in ppm)
/
I
Temp. Range:
C = -10OC to +70OC
I = -40OC to +85OC
M = -55OC to +125OC
S = Customer Specified
OR
/
/
200
Total
Frequency
Tolerance
(in ppm)
/
I
Temp. Range:
C = -10OC to +70OC
I = -40OC to +85OC
M = -55OC to +125OC
S = Customer Specified
10116 Rev G
IS O
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com
YS
90
01
TEM
C ERT I F I C
AT
N
IO
S
“S” if special or
custom design,
or if the
operating
voltage is other
than 5.0 V;
otherwise leave
blank.
N