CDM10V Product Brief

Product Brief
CDM10V
0–10 V dimming interface IC
The compact and highly integrated CDM10V allows designers to replace many of the discrete components used in conventional 0–10 V dimming schemes with a single device.
Analog 0–10 V to digital PWM converter for dimming
Infineon’s CDM10V is the industry’s first single-chip lighting interface IC dedicated for
lighting applications capable of transforming an analog 0–10 V input into a PWM or dimming input signal required by a lighting controller IC. The signal is delivered in the form
of a 5 mA optocoupler-ready 0 to 100 percent PWM output. One-time configuration of key
parameters such as minimum duty cycle (1 to 10 percent), PWM output frequency (200 Hz
to 2 kHz), dimmer/resistor bias current (50 µA to 500 µA) and “Dim-to-Off” functionality
allows the CDM10V to be used across a variety of different commercial and industrial LED
lighting applications. Furthermore, with “Dim-to-Off” enabled the IC also provides the
option of accepting PWM input signals.
High level of integration, achieving low BOM cost
Supplied in an ultra-miniature 6-pin SOT package, the CDM10V is ideally
suited for use on small PCBs with high component densities. Beside
the optocoupler, no additional components are needed to realize the
analog to PWM conversion.
Key features
››Small SOT23 package
››Active dimming (0–10 V)
››Passive dimming (resistor)
››PWM input
››Supply voltage 11–25 V
››Configurable PWM frequency
200–2000 Hz
››Configurable minimum duty cycle
1–10 percent
››Configurable R-DIM bias current
50–500 µA
››Configurable Dim-to-Off
››Embedded digital signal processing
maintains minimum variations from
device to device
Key benefits
Supporting wide range of supply power
A supply voltage of 11 V to 25 V ensures compatibility with all common
LED lighting applications including luminaries, troffers, downlights,
sconces, office lighting and signage.
Configurable
To configure CDM10V, eFuses are used which can be one time burned to
set the desired parameters. This allows adaptions to different application
requirements. The device is coming with default settings. The configuration is easy to understand. One byte will be sent to the UART interface.
An optional configuration board is available to perform the configuration.
Product summary
Type
Description
Ordering code
CDM10V
0–10 V dimming interface IC
SP001424754
www.infineon.com/cdm10v
››Single device solution
››One solution for various applications
with one time configuration
possibility
››Transparent PWM mode to transfer
PWM signals from secondary to
primary side
Applications
››0–10 V dimming
››Isolated signal transfer
Product Brief
CDM10V
0–10 V dimming interface IC
Typical application schematic using CDM10V
85–
305 V AC
Linefilter
CDM10V
ICL8105
VCC supply
11–25 V
VCC
LDO
Rdim+
Bandgap
› 0–10 V interface
› Resistor/potentiometer
› PWM-generator
OSC
Current
source
DIM
UVLO
GND
Iout
VFSS
ADC
8-bit
FSM
eFuses
8-bit
Current
source
PWM_out
PWM_gen
UART
Analog
Type
Description
Ordering code
CDM10V configuration
board
Tool to support the one
time configuration of
CDM10V
SP001493166
http://www.hitex.com
CDM10V demo board
Demonstration and
evaluation board
SP001493168
http://www.hitex.com
Published by
Infineon Technologies AG
85579 Neubiberg, Germany
© 2016 Infineon Technologies AG.
All Rights Reserved.
WE RESERVE THE RIGHT TO CHANGE THIS DOCUMENT AND/OR
THE INFORMATION GIVEN HEREIN AT ANY TIME.
Order Number: B121-I0285-V1-7600-EU-EC-P
Date: 04 / 2016
Digital
Configuration board
Please note!
THIS DOCUMENT IS FOR INFORMATION PURPOSES ONLY AND
ANY INFORMATION GIVEN HEREIN SHALL IN NO EVENT BE
REGARDED AS A WARRANTY, GUARANTEE OR DESCRIPTION OF
ANY FUNCTIONALITY, CONDITIONS AND/OR QUALITY OF OUR
PRODUCTS OR ANY SUITABILITY FOR A PARTICULAR PURPOSE.
WITH REGARD TO THE TECHNICAL SPECIFICATIONS OF OUR
PRODUCTS, WE KINDLY ASK YOU TO REFER TO THE RELEVANT
PRODUCT DATA SHEETS PROVIDED BY US. OUR CUSTOMERS AND
THEIR TECHNICAL DEPARTMENTS ARE REQUIRED TO EVALUATE
THE SUITABILITY OF OUR PRODUCTS FOR THE INTENDED
APPLICATION.
RxD
Demo board
Additional information
For further information on technologies, our products, the
application of our products, delivery terms and conditions
and/or prices, please contact your nearest Infineon Technologies
office (www.infineon.com).
Warnings
Due to technical requirements, our products may contain
dangerous substances. For information on the types in question,
please contact your nearest Infineon Technologies office.
Except as otherwise explicitly approved by us in a written
document signed by authorized representatives of Infineon
Technologies, our products may not be used in any lifeendangering applications, including but not limited to medical,
nuclear, military, life-critical or any other applications where a
failure of the product or any consequences of the use thereof
can result in personal injury.