Packing Information

Additional Information, Aug. 2006
www.infineon.com
Packing
Edition 2006-08
Published by
Infineon Technologies AG
81726 Munich, Germany
© Infineon Technologies AG 2006.
All Rights Reserved.
Legal Disclaimer
The information given in this document shall in no event be regarded as a guarantee of conditions or
characteristics (“Beschaffenheitsgarantie”). With respect to any examples or hints given herein, any typical values
stated herein and/or any information regarding the application of the device, Infineon Technologies hereby
disclaims any and all warranties and liabilities of any kind, including without limitation warranties of
non-infringement of intellectual property rights of any third party.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
Packing
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2
2.1
2.2
2.3
2.4
2.5
Sorts of Packing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tape & Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplementary Dry-Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3.1
3.2
3.3
Tape and Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ammopack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Radial Tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4
Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5
5.1
5.2
Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Bakable Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Blister Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6
Bulk Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7
Supplementary Dry-Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Additional Information
3
4
4
5
6
7
7
2006-08
Packing
Introduction
1
Introduction
Infineon packing methods and materials are designed based on the following considerations
•
Protection against mechanical damage caused by handling and arising during shipment to the customer
•
Protection against environmental influences such as moisture
•
Protection against electrical damage caused by charging or discharging (ESD = Electro-Static Discharge)
•
Sensible handling on the part of the customer (such as, for example, processing using pick-and-place
machines)
2
Sorts of Packing
2.1
Tape & Reel
•
DIN IEC 60 286-3
The components are placed on a plastic tape (carrier tape) made of polystyrene or polycarbonate, with
correspondingly shaped recesses in its surface, which is then sealed with a cover tape (transparent foil). The tape
is wound on to a reel, and supplied in a cardboard box (resembling a pizza box). There are now also larger boxes,
including the so-called "Big-Box", which can accommodate up to 10 reels.
Removable cover tape
ø330
12
11
10
Direction of unreeling
9
8
7
6
5
4
ø180
3
Upper side
2
Sd
1
Removable
cover tape
93
07
Sd
Infi
neo
8
Additional customer label
(optional)
n
Infi
neo
n
Barcode label
(readable in this position)
CTPG5610
Figure 1
Tape & Reel
ø Reel 180 mm and 330 mm
Additional Information
4
2006-08
Packing
Sorts of Packing
2.2
•
Tube
DIN IEC 60 286-4
In this case, the components are inserted into a PVC tube of appropriate cross sectional shape and standard
length (528 mm-2). It is open on both sides and after filling is sealed using stoppers or pins. A number of tubes in
one box form a packing unit.
CPDS9071
Figure 2
Tube
Additional Information
5
2006-08
Packing
Sorts of Packing
2.3
•
Tray
DIN IEC 60 286-5
Here, the components are placed in rows in special compartmentalized plastic trays. One or more such trays laid
one on top of the other here make up a packing unit.
n Trays + 1 Top Tray
Bakable Tray
CPDS9076
Blister Tray
CPDS5918
Figure 3
Tray’s
Additional Information
6
2006-08
Packing
Sorts of Packing
2.4
•
Supplementary Dry-Pack
JEDEC-STD-033B
Prior to packing, the components are heated to 125° C, for example, over a period of 24 hours, and then vacuumsealed in a bag made of composite aluminum-plastic material. A desiccant is included in the packaging to remove
residual moisture and soak up moisture penetrating the packaging during storage. An accompanying moisture
indicator card shows the relative humidity level as a means of control.
2.5
Boxes
For each type of packing, there is an appropriate, correctly proportioned box or outer pack.
O
V RIG
E
PA R IN
C PA AL
K C
IN K
G T
Each outer pack also receives a product label, on which all the important data is printed, in the form of a barcode
and plain text (BPL = Barcode Product Label). After undergoing quality control, the boxes are sealed with an
Infineon packing label.
Infineon packing label
Inf
ine
on
Barcode label
Figure 4
Box
Please consult your nearest Infineon semiconductor solder offices (see list of addresses) if you have any queries
regarding the packging units or multiple use.
Subject to change in the light of the new Packaging Act.
Additional Information
7
2006-08
Packing
Tape and Reel
3
Tape and Reel
3.1
Tape
•
DIN IEC 60 286-3
CPDG9074
e.g.
e.g
.3
45
*)
345
*) Carrier tape width + 14 mm
Figure 5
CPDC9073
Packing for Tape & Reel1)
1) All dimensions in mm
Additional Information
8
2006-08
Packing
Tape and Reel
Removable cover tape
ø330
12
11
10
Direction of unreeling
9
8
7
6
5
4
ø180
3
Upper side
2
Sd
1
Removable
cover tape
93
07
Sd
Infi
neo
8
Additional customer label
(optional)
n
Infi
neo
n
Barcode label
(readable in this position)
CTPG5610
Figure 6
ø Reel 180 mm and 330 mm
Carrier tape width: 8, 12, 16 [mm]
Direction of unreeling
ø330
Upper side
Removable
cover tape
12
11
10
9
8
7
6
5
4
3
Sd
Additional customer label
(optional)
2
1
93
07
8
Infi
neo
Barcode label
(readable in this position)
n
CTPG5611
Figure 7
ø Reel 330 mm
Carrier tape width: 16, 24, 32, 44 [mm]
Additional Information
9
2006-08
Packing
Tape and Reel
Direction of unreeling
Upper side
ø180
Upper side
Bottom side
Sd
Infi
neo
Additional customer label
(optional)
n
Barcode label
(readable in this position)
CPCG1161
Figure 8
ø Reel 180 mm
Embossed Carrier tape width: 8 [mm]
Carrier tape width > 12 mm
13 ±0.2
13 ±0.2
30 ±10
Carrier tape width w 12 mm
on
CTPC5912
CTPC5911
Figure 9
Fixing on the Tape1)
1) All dimensions in mm
Additional Information
10
2006-08
Packing
Tape and Reel
Direction of unreeling
1.5 +0.1
4 ±0.1
Trailer (empty)
Leader (empty)
(1 x Circumference / Hub)
min. 160 mm
(1 x Circumference / Reel)
min. 400 mm
CPTG5915
Figure 10
Direction of Unreeling1)
There shall be a leader of 400 mm minimum of cover tape, which includes at least 100 mm of carrier tape with
empty compartments. All the leader may consist of the carrier tape with empty compartments, sealed by cover tape.
For 1 Tape (resembling a pizza box)
S
d
ine
on
O
V R IG
E
PA R IN
C PA AL
K C
IN K
G T
Inf
Infineon packing label
Up to 10 Tapes
S
d
ine
on
O
V R IG
E
PA R IN
C PA AL
K C
IN K
G T
Inf
Infineon packing label
Inf
ine
Inf
on
ine
on
Barcode label
CTPC5914
Figure 11
CTPC5913
Labels and Boxes
1) All dimensions in mm
Additional Information
11
2006-08
Packing
Tape and Reel
3.2
•
Ammopack
Placed in Zigzag (DIN IEC 60 286-2)
e.g
.
34
5
.
e.g 35
3
/
5
8
e.g.
4
6
CPOC9068
Up to 8.000 Components, Ammopack1)
e.g
.
34
5
Figure 12
CPOC5890
.
e.g
46
e.g.
8
5
CPOC5891
CPOC9069
Figure 13
Up to 2.000 Components, Ammopack1)
1) All dimensions in mm
Additional Information
12
2006-08
Packing
Tape and Reel
EG1
EG2
CPOC5910
Figure 14
CPOC5907
Supplementary Code for Ammopack
Additional Information
13
2006-08
Packing
Tape and Reel
3.3
Radial Tape
18
ø355
45 MAX. (internal size)
CTPG9115
2 Tapes per Box
e.g
.
37
5
e.g.
115
e.g.
3
75
CTPC9078
Figure 15
Packing for Radial Tape1)
1) All dimensions in mm
Additional Information
14
2006-08
Packing
Tape and Reel
EG1
EG2
CPOC5910
Figure 16
CPOC5907
Supplementary Code for Radial Tape
Additional Information
15
2006-08
Packing
Tube
4
•
•
Tube
DIN IEC 60 286-4
Standard Length: 528-2 mm; coated (unless stated to the contrary)
e.g
.
56
5
CPDS9071-1
.
e.g m a x .
85
e.g.
1
30
CPDC9072
Figure 17
Packing for Tube1)
1) All dimensions in mm
Additional Information
16
2006-08
Packing
Trays
5
Trays
5.1
Bakable Tray
•
Temperature max. 150°C (DIN IEC 60 286-5)
n Trays + 1 Top Tray
e.g. 315
e.g. 136
e.g. 7.6 / 12.2
CPDS9076
Mark for Pin 1
Figure 18
CCQB5888
Bakable Tray1)
1) All dimensions in mm
Additional Information
17
2006-08
Packing
Trays
.
e.g
35
e.g
.
36
5
For 1 Tray
e.g.
150
CPDS9079
For 7 Trays
e.g
.
38
0
.
e.g
90
e.g.
180
CPDS9080
For 10 Trays
e.g
.
38
0
.
e.g
5
11
e.g.
1
80
CPDS9081
Figure 19
Type of Boxes for Bakable Tray1)
1) All dimensions in mm
Additional Information
18
2006-08
Packing
Trays
5.2
Blister Tray
e.g. 21.5 / 24
Upper Part
e.g. 135 / 203.2
e.g. 245 / 279.4
e.g. 15.5 / 21
Lower Part
e.g. 135 / 203.2
e.g. 245 / 279.4
Figure 20
Blister Tray1)
1) All dimensions in mm
Additional Information
19
2006-08
Packing
Trays
CPDS5918
e.g
.
27
5
.
e.g
0
10
e.g.
1
43
CCGC9067
e.g
.
30
5
.
e.g
55
e.g.
2
20
CPDS9080
Figure 21
Packing for Blister Tray1)
1) All dimensions in mm
Additional Information
20
2006-08
Packing
Bulk Material
Bulk Material
.
e.g
29
e.g
.1
40
6
e.g.
9
2
CMTC9070
Figure 22
Bulk Material1)
1) All dimensions in mm
Additional Information
21
2006-08
Packing
Supplementary Dry-Pack
7
•
Supplementary Dry-Pack
JEDEC-STD-033B
Stopper
Device
Stopper
Moisture Indicator
Desiccant
Inner Container
Barrier Bag
COOS5895
Figure 23
Example Dry-Pack e.g. for Tubes
Additional Information
22
2006-08
www.infineon.com
Published by Infineon Technologies AG