CH-516TXAS PC/CV Scaler over CAT5e/6/7 Transmitter with LAN/ RS-232/IR/Bidirectional PoE Operation Manual DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document. Cypress Technology reserves the right to make improvements to this document and/or product at any time and without notice. COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from Cypress Technology. © Copyright 2011 by Cypress Technology. All Rights Reserved. Version 1.0 September 2011 TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated. SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product. • Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. • Do not attach the power supply cabling to building surfaces. • Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. • Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. • To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. REVISION HISTORY VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE VR0 01/11/13 Preliminary release VS1 09/10/13 Updated text/diagrams CONTENTS 1. Introduction�������������������������������������������� 1 2. Applications������������������������������������������� 1 3. Package Contents�������������������������������� 1 4. System Requirements���������������������������� 1 5. Features�������������������������������������������������� 2 6. Operation Controls and Functions������� 3 6.1 Front Panel�����������������������������������������3 6.2 Rear Panel�����������������������������������������4 6.3 Remote Control���������������������������������5 6.4 IR Cable Pin Assignment������������������5 6.5 RS-232 Pin Definitions������������������������6 6.6 RS-232 Commands���������������������������7 6.7 OSD Menu������������������������������������������9 6.8 Input Resolutions Support���������������11 7. Connection Diagram�������������������������� 12 8. Specifications�������������������������������������� 13 8.1 Technical Specifications����������������13 8.2 CAT5e/6/7 Cable Specification����14 9. Acronyms��������������������������������������������� 14 1. INTRODUCTION The CH-516TXAS is an HDBaseT™ Transmitter Scaler supporting PC or Composite Video (CV) input. It can scale and switch the video sources, and send the digitalized signal over a single run of CAT5e/6/7 cable to the Receiver at a distance up to 100 meters, along with an external audio input, 2-way IR, RS-232 and bidirectional LAN serving. Control is via on-panel buttons or IR remote control and there is an On-screen Display (OSD) providing selection and system information. The device provides a full range of output resolutions, up to 1080p and WUXGA (RB). The bidirectional Power over Ethernet (PoE) function provides greater flexibility in installations. 2. APPLICATIONS • Analog to Digital video signal conversion • Up scale standard definition video to High-Definition TVs/displays • Extend the operating distance of a CV/PC video signal • Lecture room/Showroom/Meeting room/Classroom display and control 3. PACKAGE CONTENTS • CV/PC to CAT5e/6/7 with LAN/IR/RS-232/Bidirectional PoE Transmitter • 1×IR Extender • 1×IR Blaster • 24 V/2.7 A DC Power Adaptor • Remote Control (CR-128) • Operation Manual 4. SYSTEM REQUIREMENTS CV/PC source equipment such as a DVD/Video player or PC/Laptop and output to HDBaseT compatible Receiver. 1 5. FEATURES • Supports PC/CV scaling to a full range of HDTV or PC resolutions up to 1080p and WUXGA (RB) • Transmission of uncompressed data over a single CAT5e/6/7 cable up to 100m/328ft • 5Play™ convergence: Video and Audio, LAN serving, bidirectional Power over Ethernet (PoE) and Control (IR/RS-232 bypass) • Supports IR, Remote control, RS-232 (bypass) and on-panel controls • Provides bidirectional 24V DC power to or receive from compatible PoE Receiver through CAT5e/6/7 cable • Supports Ethernet transmission rates up to 100 Mbps • Supports NTSC and PAL formats for Composite Video input Note: 1. This system was tested with CAT6/23AWG cables, results may vary with cables of different specifications. 2. The PoE function is designed for powering compatible Receiver units only—non-PoE Receivers will need their own power supply. Receivers from other brands may not be compatible. 3. DO NOT connect the LAN connection to the CAT5e/6/7 port. Doing so may cause a power shutdown and may damage the device. 2 6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel 7 SERVICE PC INPUT CV/PC CV INPUT AUDIO MENU XGA - + ENTER 720P 1 2 3 4 5 6 8 9 1 SERVICE: Reserved for manufacturer use only. 2 IR RECEIVER WINDOW: Receives only the IR signal from the supplied remote control for this device only. 3 PC: Connect to a PC/Laptop source device with a D-Sub 15pin cable. 4 CV: Connect to a composite video source such as a DVD/Video player. 5 AUDIO: Connect to an analog stereo (L/R) audio source with a 3.5mm mini-jack cable. 6 MENU: Press this button to enter the On-Screen Display (OSD) menu. 7 INPUT (–) Button & CV/PC LED: Press the INPUT (−) button to toggle between CV or PC inputs. When in CV mode the LED will be lit, off when in PC mode. 8 −/+: Use these buttons to navigate down and up in the on-screen menu. 9 ENTER: Press this button to confirm the selection. Note: Pressing '−' (MINUS) and ENTER simultaneously will immediately switch the output resolution of the device to 720p60. Pressing '+' (PLUS) and ENTER simultaneously will immediately switch the output resolution of the device to XGA (1024×768). 3 6.2 Rear Panel DC 24V RS232 IN LAN IR Blaster IR Extender CAT5e/6 OUT POWER MODE 1 2 3 4 5 6 LINK 7 1 POWER LED: This LED will illuminate when the device is connected to an active power supply. 2 DC 24V: Connect the 24 V DC power supply to the unit and plug the adaptor into an AC outlet. Only one unit requires powering if both the Transmitter and Receiver are both PoE compatible. 3 RS-232 IN: Connect to a PC or RS-232 control system with a D-Sub 9 pin male cable for the transmission of RS-232 commands. 4 LAN: Connect to an active network for LAN serving. When any compatible LAN equipped receivers are connected, this allows the network access (including internet access if available) to be shared between any connected LAN equipped receivers. Connect any Ethernet equipped device e.g. a Smart TV or games console to the LAN port of a receiver for that device to share the network/internet access. Warning: DO NOT connect the LAN connection to the CAT5e/6/7 port. Doing so may cause a power shutdown and may damage the device. 5 IR Blaster: Connect the supplied IR Blaster cable for IR signal transmission. Place the IR Blaster in direct line-of-sight of the equipment to be controlled. 6 IR Extender: Connect the supplied IR Receiver cables for IR signal reception. Ensure that remote being used is within the direct lineof-sight of the IR Extender. 7 CAT5e/6/7 OUT: Connect to the Receiver unit with a single CAT5e/6/7 cable for transmission of all data signals. MODE LED: This LED will illuminate when the power is connected. LINK LED: This LED will illuminate when connected to a Receiver unit that is connected with a TV/monitor that is displaying the signal. 4 6.3 Remote Control 1 INPUT: Press this button to toggle between the CV or PC input. 2 EXIT:Press this button to exit the menu or the current selection in the on-screen 1 menu. 3 MENU: Press this button to enter into the 2 INPUT EXIT OSD menu. MENU OK 4 RESET: Press this button to return the device to the factory default settings. 5 AUTO ADJUST: Press this button to 5 4 RESET AUTO ADJUST 6 optimize the positioning of the picture (picture centering) on the screen. 6 OK & ▲▼◄►: Press 'OK' to confirm the selection or use the directional buttons to navigate the on-screen menus. CR-128 6.4 IR Cable Pin Assignment IR Blaster 1 Power 2 IR Blaster Signal 3 NC IR Extender 1 IR Signal 2 Power 3 Ground 5 3 6.5 RS-232 Pin Definitions PIN DEFINE TX / RX 1 N/C 2 TxD/RxD 3 RxD/TxD 4 NC 5 GND 6 NC 7 NC 8 NC 9 NC Baud Rate: 9600bps Data bit: 8 bits Parity: None Flow Control: None Stop Bit: 1 6 6.6 RS-232 Commands COMMAND DESCRIPTION S SOURCE 1~2 1=VIDEO 2=PC R SOURCE Reports the numerical equivalent for the SOURCE setting (as listed above) S OUTPUT 0~25 0=Native 12=1600×1200 1=640×480 13=1920×1080 2=800×600 16=1920×1200 3=1024×768 17=480p 5=1360×768 18=720p@60 6=1280×720 19=1080p@60 7=1280×800 20=1080i@60 8=1280×1024 22=576p 9=1440×900 23=720p@50 10=1400×1050 24=1080p@50 11=1680×1050 25=1080i@50 R OUTPUT Reports the numerical equivalent for the OUTPUT setting (as listed above) S SIZE 0~6 0=OVERSCAN 4=LETTER BOX 1=FULL 5=UNDER 2 2=BEST FIT 6=UNDER 1 3=PAN SCAN R SIZE Reports the numerical equivalent for the SIZE setting (as listed above) S CONTRAST 0~60 Sets the numerical value for the CONTRAST setting (0~60) R CONTRAST Reports the numerical value for the CONTRAST setting (0~60) S BRIGHTNESS 0~60 Sets the numerical value for the BRIGHTNESS setting (0~60) R BRIGHTNESS Reports the numerical value for the BRIGHTNESS setting (0~60) 7 COMMAND DESCRIPTION S HUE 0~60 Sets the numerical value for the HUE setting ((0~60) R HUE Reports the numerical value for the HUE setting (0~60) S SATURATION 0~60 Sets the numerical value for the SATURATION setting (0~60) R SATURATION Reports the numerical value for the SATURATION setting (0~60) S SHARPNESS 0~30 Sets the numerical value for SHARPNESS setting (0~30) R SHARPNESS Reports the numerical value for the SHARPNESS setting (0~30) S NR 0~3 0=OFF 2=MIDDLE 1=LOW 3=HIGH R NR Reports the numerical equivalent for the NOISE REDUCTION setting (as listed above) S AUDIO DELAY 0~3 0=OFF 2=110ms 1=40ms 3=150ms R AUDIO DELAY Reports the numerical equivalent for the AUDIO DELAY setting (as listed above) S AUDIO MUTE 0/1 0=ON R AUDIO MUTE Reports the numerical equivalent for the AUDIO MUTE setting (as above) S KEY LOCK 0/1 0=ENABLE R KEY LOCK Reports the numeric equivalent for the KEY LOCK setting (as listed above) FW Checks the FIRMWARE version S RESET 1 Sets the numerical equivalent for the RESET setting (as left) 1=MUTE 1=DISABLE Note: 1. RS-232 commands will not execute unless followed by a carriage return and LF (Line Feed). 2. Commands are not case-sensitive. 3. Resolutions 1~16 are RGB encoded and 17~25 are YUV encoded. 8 6.7 OSD Menu 1ST LAYER 2ND LAYER 3RD LAYER DISPLAY OUTPUT Native 640x480 60 800x600 60 1024x768 60 1360x768 60 1280x720 60 1280x800 60 1280x1024 60 1440x900 60 1400x1050 60 1680x1050 60 1600x1200 60 1920x1080 60 1920x1200 60 720x480P 60 1280x720P 60 1920x1080I 60 1920x1080P 60 720x576P 50 1280x720P 50 1920x1080I 50 1920x1080P 50 SIZE SIZE OVER SCAN FULL ASPECT RATIO PAN SCAN LETTER BOX UNDER 2 UNDER 1 9 4TH LAYER 1ST LAYER 2ND LAYER 3RD LAYER SIZE MODE INFO INFO 4TH LAYER ON OFF PC (PC mode only) AUTO SETUP NO YES H_POSITION 0~60 (30) V_POSITION 0~60 (30) PHASE CLOCK WXGA/XGA XGA WXGA RESET NO YES COLOR COLOR R G B R OFFSET G OFFSET B OFFSET CONTRAST 0~60 BRIGHTNESS 0~60 HUE 0~600~60 SATURATION 0~60 SHARPNESS 0~60 NR. OFF LOW MIDDLE HIGH 10 1ST LAYER 2ND LAYER 3RD LAYER AUDIO VOLUME 0~100 DELAY OFF 4TH LAYER 40ms 110ms 150ms SOUND ON MUTE SETUP FACTORY RESET NO YES KEY LOCK OFF ON INFORMATION INPUT OUTPUT REVISION Note: Items in Bold are the default settings. 6.8 Input Resolutions Support INPUT RESOLUTION CV PC NTSC/PAL - VGA@60/72/75 Hz - SVGA@56/60/72/75 Hz - XGA@60/70/75 Hz - SXGA@60/75 Hz - UXGA@60 Hz - 1280×800@60 Hz - 1680×1050@60 Hz (RB) - 1920×1080@60 Hz - 11 7. CONNECTION DIAGRAM PC/Laptop Video/DVD Player VGA Input Composite Video Input 1.5m 60° Analog Stereo Input Power Supply 3m m 7m m 3m m 60° SERVICE PC INPUT CV/PC CV XGA INPUT AUDIO MENU - + ENTER 720P DC 24V RS-232 Control System RS232 IN LAN IR Blaster IR Extender CAT5e/6 OUT POWER MODE LINK IR Extender RS-232 IR Blaster CAT5e/6/7 Cabe (100m) LAN RS-232 Out HDMI Out LAN Compatible PoE Receiver unit Receiver CAT5e/6 to HDMI with LAN/IR/RS232 Router with Internet Connection IR Extender IR Blaster HDMI Output LAN 60° 1.5m 60° 3m m 7m m 3m Smart TV 12 8. SPECIFICATIONS 8.1 Technical Specifications Ethernet Speed 100 Mbps Output Video Bandwidth 300MHz / 10.2Gbps Input Ports 1×Composite Video, 1×VGA, 1×3.5mm Mini-jack (L/R), 1×RS-232, 1×LAN, 1×IR Extender Output Ports 1×CAT5e/6/7, 1×IR Blaster CAT5e/6/7 Out Cable Up to 100 Meters Distance CV Resolutions Support NTSC/PAL VGA Resolutions Support VGA~WUXGA (RB) CAT5e/6/7 Resolutions HD: Up to 1080p@60 Hz Support PC: Up to WUXGA (RB) IR Frequency 30~50 kHz ESD Protection Human body model: ±8kV (air-gap discharge) ±4kV (contact discharge) Dimensions 145 mm (W)×192 mm (D)×30 mm (H)/Jacks Excluded 145 mm (W)×202 mm (D)×30 mm (H)/Jacks Included Weight 606 g Chassis Material Aluminum Color Black Operating Temperature 0 ˚C~40 ˚C / 32 ˚F~104 ˚F Storage Temperature −20 ˚C ~ 60˚C / −4 ˚F ~ 140 ˚F Relative Humidity 20 ~ 90 % RH (non-condensing) Power Consumption 16 W 13 8.2 CAT5e/6/7 Cable Specification Cable Type Range CAT5e/6/7 100 m Pixel Clock Video Data Supported Video Rate Rate ≤225 MHz ≤5.3 Gbps Up to 1080p, 60 Hz, (HD Video) 36 bits, 3D (data rates lower than 5.3 Gbps or below 225 MHz TMDS clock). 9. ACRONYMS ACRONYM COMPLETE TERM CAT5e Category 5 Cable CAT6 Category 6 Cable CAT7 Category 7 Cable CV Composite Video DVI Digital Visual Interface HDMI High-Definition Multimedia Interface IR Infrared WUXGA (RB) Widescreen Ultra Extended Graphics Array (Reduced blanking) 14 CYPRESS TECHNOLOGY CO., LTD Home page: http://www.cypress.com.tw 20130624 MPM-CH516TXAS