CH-507TXBD & RXBD DR A FT HDMI to CAT5e/6 with LAN/IR/RS-232/ Bidirectional PoE Operation Manual FT A DR DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document. Cypress also makes no commitment to update or to keep current the information contained in this document. FT Cypress Technology reserves the right to make improvements to this document and/or product at any time and without notice. COPYRIGHT NOTICE A No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means— electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from Cypress Technology. © Copyright 2012 by Cypress Technology. All Rights Reserved. DR Version 1.0 December 2012 TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated. SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. • To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product. • Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. • Do not attach the power supply cabling to building surfaces. • Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. • Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. • To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. DR A FT • REVISION HISTORY VERSION NO. DATE DD/MM/YY SUMMARY OF CHANGE RDV1 07/12/12 Preliminary Released CONTENTS 1. Introduction�������������������������������������������� 1 2. Applications������������������������������������������� 1 3. Package Contents�������������������������������� 1 4. System Requirements���������������������������� 1 5. Features�������������������������������������������������� 2 6. Operation Controls and Functions������� 3 6.1 Transmitter Front and Rear Panels��3 FT 6.2 Receiver Front and Rear Panels�����4 6.3. IR Cable Pin Assignment����������������5 6.4. D-Sub 9 Pin Definitions��������������������5 7. Connection Diagram���������������������������� 6 8. Specifications���������������������������������������� 7 DR A 9. Acronyms����������������������������������������������� 8 1. INTRODUCTION The HDMI with RS-232 over Single CAT5e/6 transmitter and receiver set can send uncompressed audio/video over a single run of CAT5e/6 cable up to 100 m with PoE feature and the added benefit of control through the built-in RS-232 and IR ports and a bi-directional LAN connection. 2. APPLICATIONS • Household entertainment sharing and control • Lecture room display and control FT • Showroom display and control • Meeting room presentation and control • Classroom display and control 3. PACKAGE CONTENTS A • 1×HDMI to CAT5e/6 (with LAN/IR/RS-232/Bidirectionlal PoE) Transmitter • 1×CAT5e/6 to HDMI (with LAN/IR/RS-232/Bidirectionlal PoE) Reciever • 1×IR Blaster DR • 1×IR Receiver • 1×24 V/1.25 A DC Power Adaptor • Operation Manual 4. SYSTEM REQUIREMENTS Input HDMI source equipment such as DVD/Blu-ray player and HDMI equipped output display (TV or monitor). 1 5. FEATURES • HDMI 1.4 with 3D, 4k×2k support, HDCP & DVI Compliant • Supports CEC bypass • Simultaneous transmission of uncompressed data over a single 100 m/328 ft CAT5e/6 cable • Uncompressed video 1080p, 60 Hz, 36-bit • Audio support up to 7.1CH & Dolby TrueHD, DTS-HD • 5Play™ convergence: HDMI, LAN, Bidirectionlal PoE & Control (IR & RS-232) • Installation Friendly Note: FT 1. This system was tested with CAT6/23AWG cables, results may vary with cables of a different specification. DR A 2. The PoE function is designed for powering compatible receiver units only—non-PoE receivers will need their own power supply. Receivers of another brand may not be compatible. 2 6. OPERATION CONTROLS AND FUNCTIONS 6.1 Transmitter Front and Rear Panels Front Rear RS-232 In HDMI In IR1 Blaster Transmitter Link Power LAN 1 2 DC 24V IR2 Extender HDMI to CAT5e/6 with LAN/IR/RS232 3 4 5 6 7 CAT5e/6 Out 8 9 ray player. FT 1 HDMI In: Connect to HDMI source equipment such as a DVD or Blu2 LAN: Connect to an internet or network connection. 3 RS-232 In: Connect to a PC or laptop with D-Sub 9 pin male cable for the transmission of RS-232 commands. A 4 Power LED: This blue LED will illuminate when the device is connected to a power supply. 5 DC 24V: Plug the 24 V DC power supply into the unit and connect the adaptor to an AC outlet. Only one side of power needs to be DR connected to activate both transmitter and receiver. 6 IR 1 Blaster: Connect to the supplied IR blaster cable for IR signal transmission. Place the IR blaster in direct line-of-sight of the equipment to be controlled. 7 IR 2 Extender: Connect to the supplied IR receiver cables for IR signal reception. Ensure that remote being used is within the direct line-of-sight of the IR extender. 8 Link LED: The yellow LED will illuminate when both the input and output signals are connected. 9 CAT5e/6 Out: Connect to the reciever unit with a Single CAT5e/6 cable for tranmission of all data signals. 3 6.2 Receiver Front and Rear Panels Front HDMI Out IR2 Blaster Receiver Link Power LAN 1 Rear RS-232 Out 2 DC 24V IR1 Extender CAT5e/6 to HDMI with LAN/IR/RS232 3 4 5 6 7 CAT5e/6 In 8 9 1 HDMI Out: Connect to a HDMI equipped TV/monitor for display of the HDMI input source signal. connection. FT 2 LAN: Connect to a PC or Laptop to the Internet or network 3 RS-232 Out: Connect to the device that is to be controlled (via D-Sub 9 pin female cable) by RS-232 commands. 4 Power LED: This blue LED will illuminate when the device is A connected to a power supply. 5 DC 24V: Plug the 24 V DC power supply into the unit and connect the adaptor to an AC outlet. Only one side of power needs to be connected to activate both transmitter and receiver. DR 6 IR 2 Blaster: Connect to the supplied IR blaster cable for IR signal transmission. Place the IR blaster in direct line of sight of the equipment to be controlled. 7 IR 1 Extender: Connect to the supplied IR receiver cables for IR signal reception. Ensure that remote being used is within the direct line-of-sight of the IR extender. 8 Link LED: The yellow LED will illuminate when both the input and output signals are connected. 9 CAT5e/6 In: Connect to the transmitter unit with a Single CAT5e/6 cable for tranmission of all data signals. 4 6.3. IR Cable Pin Assignment IR Blaster 1 Power 5 V 2 IR Blaster Signal FT 3 NC IR Receiver 1 2 A 3 DR 6.4. D-Sub 9 Pin Definitions 5 Pin Define TX / RX 1 N/C 2 TxD / RxD 3 RxD / TxD 4 N/C 5 GND 6 N/C 7 N/C 8 N/C 9 N/C IR Signal Power 5 V Grounding 7. CONNECTION DIAGRAM DVD or Blu-ray Player Internet Modem or Router 1.5m HDMI CAT5e/6 60° RS-232 IR Blaster Power Supply 3m LAN 3m 60° Transmitter HDMI to CAT5e/6 with LAN/IR/RS232 IR1 Blaster Link Power DC 24V IR2 Extender TX CAT5e/6 Out RS-232 Equipped PC or Notebook IR Extender A IR Extender 3m RS-232 In HDMI In FT 7m 7m 60° 3m IR2 Blaster Link Power DC 24V IR1 Extender IR Blaster CAT5e/6 In RS-232 Out HDMI Out LAN Receiver RX CAT5e/6 to HDMI with LAN/IR/RS232 DR 60° 1.5m HDMI TV or Monitor RS-232 RS-232 Equipped HDMI Switcher CAT5e/6 Notebook Note:Only one side of power needs to be connected to activate both transmitter and receiver. 6 8. SPECIFICATIONS Video Bandwidth 300MHz / 9Gbps Ethernet Speed 100 Mbps Transmitter Input 1×HDMI, 1×IR Extender,1×RS-232, 1×LAN Output 1×CAT5e/6, 1×IR Blaster Receiver 1×CAT5e/6, 1×IR Extender Output 1×HDMI, 1×RS-232, 1× IR Blaster, 1× LAN HDMI In/Out Cable Distance CAT6 In/Out Cable Distance FT Input HDMI In/Out Supports Up to 100 Meters 480i~1080p@50/60, 1080p@24, VGA~WUXGA A Resolution Up to 10 Meters IR Frequency 30~50 kHz ESD Protection Human Body Model: DR ±8 kV (air-gap discharge) ±4 kV (contact discharge) Power Supply 24 V/1.25 A DC (US/EU Standards, CE/FCC/ UL certified) Dimensions 102 mm (W)×113 mm (D)×25 mm (H)/each Weight 252 g (TX), 256 g (RX) Chassis Material Aluminum Silkscreen Color Silver Power Consumption 13 W Operating Temperature 0 °C~40 °C/32 °F ~104 °F Storage Temperature −20 °C~60 °C/−4 °F~140 °F Relative Humidity 20~90 % RH (non-condensing) 7 9. ACRONYMS COMPLETE TERM CAT5e Category 5 Cable CAT6 Category 6 Cable CEC Consumer Electronics Control DVI Digital Visual Interface HDCP High-bandwidth Digital Content Protection HDMI High Definition Multimedia Interface IR Infrared DR A FT ACRONYM 8 FT A DR FT A DR FT A DR CYPRESS TECHNOLOGY CO., LTD Home page: http://www.cypress.com.tw