2016 Products Catalog Conductive Polymer Aluminum Solid Capacitors 2016.06 http://industrial.panasonic.com/ww/products/capacitors/polymer-capacitors/os-con ——— Notices ——— ■ Applicable Laws and Regulations ● This product complies with the RoHS Directive (Restriction of the use of certain Hazardous substances in electrical and electronic equipment (DIRECTIVE 2011/65/EU). ● No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in producing this product. ● We do not PBBs or PBDEs as brominated flame retardants. ● Export procedure which followed export related regulations, such as foreign exchange and a foreign trade method, on the occasion of export of this product Thank you for your consideration. ■ Limited applications ● This capacitor is designed to be used for electronics circuits such as audio/visual equipment, home appliances, computers and other office equipment, optical equipment, measuring equipment. ● High reliability and safety are required [ be / a possibility that incorrect operation of this product may do harm to a human life or property ] more. When use is considered by the use, the delivery specifications which suited the use separately need to be exchanged. ——— Items to be observed ——— ● This specification guarantees the quality and performance of the product as individual components. Before use, check and evaluate their compatibility with installed in your products. ● Do not use the products beyond the specifications described in this document. ■ For specifications ● Install the following systems for a failsafe design to ensure safety if these products are to be used in equipment where a defect in these products may cause the loss of human life or other signification damage, such as damage to vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment, electric heating appliances, combustion/ gas equipment, rotating rotating equipment, and disaster/crime prevention equipment. · The system is equipped with a protection circuit and protection device. · The system is equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault. ■ Conditions of use ● Before using the products, carefully check the effects on their quality and performance, and determined whether or not they can be used. These products are designed and manufactured for general-purpose and standard use in general electronic equipment. These products are not intended for use in the following special conditions. (1) In liquid, such as Water, Oil, Chemicals, or Organic solvent. (2) In direct sunlight, outdoors, or in dust. (3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a high concentration corrosive gas, such as Cl2, H2S, NH3, SO2, or NOx. (4) In an environment where strong static electricity or electromagnetic waves exist. (5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near these products. (6) Sealing or coating of these products or a printed circuit board on which these products are mounted, with resin and other material. (7) Using resolvent, water or water-soluble cleaner for flux cleaning agent after soldering. (In particular, when using water or a water-soluble cleaning agent, be careful not to leave water residues) (8) Using in the atmosphere which strays Acid or alkaline. (9) Using in the atmosphere which there are excessive vibration and shock. ● Please arrange circuit design for preventing impulse or transitional voltage. Do not apply voltage, which exceeds the full rated voltage when the capacitors receive impulse voltage, instantaneous high voltage, high pulse voltage etc. ● Our products there is a product are using an electrolyte solution. Therefore, misuse can result in rapid deterioration of characteristics and functions of each product. Electrolyte leakage damages printed circuit and affects performance, characteristics, and functions of customer system. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 00 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Guidelines and precautions (OS-CON) 1. Circuit design 1.1 Prohibited circuits (a) Leakage current of the OS-CON may increase in the following conditions. (1) Soldering (2) When voltage is not applied : high temperature no-load test, high temperature and high humiditynoload test, rapidly changing temperature test, etc. (b) Avoid the use of the OS-CON in the following type of circuits because leakage current may increase. (1) High-impedance circuits (2) Coupling circuits (3) Time constant circuits (4) Other circuits that are significantly affected by leakage current ✽ If you plan to use 2 or more OS-CONs in a series connection, please contact us before use 1.2 Failure and life-span The failure rate is 0.5 % /1000 h (Confidence level : 60 %) based on JIS C 5003. The prospective failure is not zero. The mainly failure modes are as follows. 1.2-1 Contingency failure The most common failure mode is a short circuit. Mainly caused by the soldering or operating temperature environment, along with heat stresses, electrical stresses or mechanical stressesas follows. (1) Applying voltage over the rated voltage. (2) Applying reverse voltage (3) Excessive mechanical stress (4) Applying rush current by sudden charge or discharge out of the specification. (a) The following phenomenon is seen when short-current is applied to the OS-CON. (1) When current is relatively low (f10 : approx 1 A or less, f8 : approx 0.5 A or less, f6.3 : approx 0.2 A or less) The OS-CON becomes heated, but no effects are visible even when the current is continously carried. (2) When the short circuit currents exceed the mentioned value above. After internal temperature increase, sealing rubber may be turned over. In some cases, odorous gas may be produced. (b) In case a short circuit occurs, ensure safety by fully considering the followings. (1) If odorous gas is released, turn off the main power of the equipment. In this case, keep your face and hands away from the area. (2) Though it depends on the conditions, it takes seconds to minutes before odorant gas generates. Protective circuit should operate in this period. (3) If the gas comes into eyes, rinse immediately. If the gas is inhaled, gargle immediately. (4) Do not lick the electrolyte. If the electrolyte touches skin, wash it off with soap immediately. (5) The OS-CON contains combustible substances. In case a large current continues to flow after a short circuit, in the worst case, the shorted-out section may ignite. For safety, install a redundant circuit or a protective circuit, etc. 1.2-2 Wear-out failure (life time) When lifetime span exceeded the specified guarantee time of endurance and damp heat, electrolyte might insulate and cause electric characteristic changed. This is called an open circuit. The electric characteristics of capacitance and ESR may possibly change within the specified range in specifications even if it is used under the condition of the rated voltage, electric and mechanical performance. Please note it when designing. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors 1.3 Leakage current Mechanical stress may cause OS-CON’s leakage current increased. In such a case, leakage current will gradually decrease by applying voltage (withinthe category voltage and the upper limit of category temperature). Then, self-healing speed of leakage current is faster when it is near to the upper limit of category temperature and the category voltage. OS-CON leakage current restoration characteristics 16 V.DC/10 μF (16 V.DC applied) OS-CON leakage current restoration characteristics 10 V.DC/33 μF (Ambient temperature : 65 °C) (Measured voltage : 10 V) 1000 Leakage current (μA) Leakage current (μA) 1000 100 10 60 °C 20 °C 1 100 5 V applied 10 8 V applied 1 10 V applied 105 °C 0.1 1 10 Time (h) 100 1000 0.1 1 10 Time (h) 100 1000 ✽ To make the recovery of LC values easy to show, samples that LC values have been increased on purpose are used in the test. 1.4 Rapid charge and discharge limitation Allowance of a large rush current to flow due to rapid charge and discharge may result in short circuit or large leakage current. The protection circuit, to maintain high reliability, is recommended when rush current to flow to the OS-CON is in the following cases. (a) Products which 10 times of allowable ripple current is less than 10 A : It is when 10 A or over of rush current is applied. (b) Products which 10 times of allowable ripple current is 10 A or over : It is when rush current, which the figure is over 10 times of allowable ripple current, is applied. 2. Mounting 2.1 Soldering with a soldering iron (a) When lead terminals for radial lead type must be processed because the lead pitch and the PCB holes do not match, process them without any stresses to the OS-CON before soldering. (b) Solder without any excessive stresses to the OS-CON itself. (c) When the OS-CON has been soldered once and needs to be removed, remove it after the solder has been completely melted. (d) Do not let the tip of the soldering iron touch the OS-CON itself. 2.2 Flow soldering (a) (b) (c) (d) (e) Do not apply flow soldering to OS-CON SMD type. Do not solder the OS-CON itself by submerging it in melted solder. Solder the opposite side that the OS-CON is mounted on. Note that flux does not adhere to anywhere expect the lead terminal. Note that other components do not fall over and touch the OS-CON when soldering. 2.3 Reflow soldering (a) Do not apply reflow soldering to OS-CON Radial Lead type. (b) Please contact us for setting VPS conditions. 2.4 Capacitor handling after soldering Do (a) (b) (c) (d) not subject the OS-CON to excessive stress as follows. Do not tilt, bend or twist the OS-CON. Do not move the PCB with holding the OS-CON itself. Do not hit the OS-CON with objects. When stacking PCBs, make sure that the OS-CON does not touch other PCBs or components. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors 2.5 Circuit board cleaning Check the following items before washing PC board with these detergents: high quality alcohol-based cleaning fluid such as Pine-a ST-100S, clean thru 750H, 750L, 710M, 750K or Techno Care FRW 14 through 17 or detergents including substitute freon as AK-225AES or IPA. (a) Use immersion or ultrasonic waves to clean within 2 minutes. (b) The temperature of the cleaning fluid should be less than 60 °C. (c) Watch the contamination of the detergent such as conductivity, pH, specific gravity, water content, etc. (d) Do not store the OS-CON in a location subject to gases from the cleaning fluid or in an airtight container after cleaning. (e) Dry the PCB or OS-CON with hot air that should be less than the upper category temperature. (f) Please note that indication may disappear when rubbing print side after washing depending on a cleaner. (g) Please contact us for details about detergents, cleaning methods and detergents other than those listed above. 2.6 Fixatives and coating materials (a) Select the appropriate covering and sealant materials for the OS-CON. In particular, don’t use acetone in the fixative, coating agent and diluent. (b) Before applying the fixative or coating, completely remove any flux residue and foreign matter from the area where the board and the OS-CON will be jointed together. (c) Allow any detergent to dry before applying the fixative or coating. (d) Please contact us for the fixative and coating heat curing conditions. 2.7 Capacitor insulation Be sure to completely separate the case, negative lead terminal, positive lead terminal and PC board patterns with each other due to the following reasons. (a) Insulation is not guaranteed at a part of resin on the surface of a case. (b) It offers inconstant resistance between a case and a negative lead terminal and it isn’t insulated. 3. Storage Open the bags just before mounting and use up all products once opened, For keeping a good solderability, store the OS-CON as follows. ✽ Due to the feature of the plating material of the lead terminal, it may rarely become dull color during the specified period as follow, but it will not affect the solderability. Before unsealing SMD type ✽1 Bag packing product Radial lead type Taping product Within 24 months after shipment Within 30 months after shipment Within 24 months after shipment After unsealing Within 30 days from opening (packaged with carrier tape) Within 7 days from opening ✽1 The JEDEC J-STD-020 standard is not applicable ◇ Intellectual property right We, Panasonic Group are providing the product and service that customers can use without anxiety, and are working positively on the protection of our products underintellectual property rights. Representative patents relating to OS-CON are as follows: US Patent Nos. 6310765, 6508846 and 7158367 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Line up A5 B6 SVPS Long life SVPB Low profile C6 C5 C55 B6 SVPA Low ESR High ripple SVQP Guaranteed at 125℃ C6 C6 Conductive Polymer Aluminum Solid Capacitors Line up A5 B6 C6 SVP Standard B9 C6 SEPC Super low ESR Large capacitance Small size Low profile 105℃5,000h C9 C6 SEQP 105℃5,000h Guaranteed at 125℃ Rated 32V max. C6 SEP Standard Conductive Polymer Aluminum Solid Capacitors Diagram SVP Standard F12 Low ESR High ripple F8 Size 4.0 to 20 V.DC 56 to 680 μF E7 Size 4.0 to 20 V.DC 33 to 330 μF F8 Size E7 Size 2.5 to 16 V.DC 180 to 820 μF 4.0 to 16 V.DC 100 to 680 μF 6.3 to 20 V.DC 47 to 220 μF E7 Size E7 Size C6 Size 2.5 to 20 V.DC 47 to 330 μF 4.0 to 25 V.DC 10 to 270 μF 4.0 to 20 V.DC 22 to 150 μF C6 Size C6 Size 2.5 to 20 V.DC 22 to 180 μF 4.0 to 20 V.DC 22 to 150 μF B6 Size B6 2.5 to 20 V.DC 10 to 82 μF 4.0 to 16 V.DC 22 to 68 μF Size Size A5 Size 2.5 to 20 V.DC 22 to 220 μF B6 SVQP Guaranteed at 125℃ F8 Size Size 2.5 to 20 V.DC 100 to 680 μF C6 Long life Size 2.5 to 20 V.DC 150 to 1,500 μF E12 SVPS SVPA Size 4.0 to 20 V.DC 10 to 68 μF A5 Size 4.0 to 16 V.DC 3.3 to 33 μF 4.0 to 10 V.DC 10 to 33 μF SVPB Low profile C55 Size 20 V.DC 22 μF C5 Size 2.5 to 20 V.DC 15 to 120 μF SEP Standard E12 Size 2.5 to 20 V.DC 100 to 680 μF E7 Size 4.0 to 20 V.DC 33 to 330 μF F13 Size 2.5 to 20 V.DC 150 to 1,500 μF F8 Size 4.0 to 20 V.DC 56 to 680 μF C6 Size 4.0 to 20 V.DC 22 to 150 μF SEPC 105℃ 5,000h Super low ESR Large capacitance F13 Size 2.5 to 16 V.DC 470 to 2,700 μF SEQP F13 Size 105℃ 5,000h 4.0 to 20 V.DC High voltage 150 to 1,200 μF Guaranteed at 125℃ E13 Size E12 Size E12 Size F8 Size 2.5 to 6.3 V.DC 470 to 820 μF 16 V.DC 180, 270 μF 4.0 to 32 V.DC 18 to 560 μF 4.0 to 32 V.DC 15 to 680 μF E9 Size E7 Size E7 Size C6 Size 2.5 to 16 V.DC 180 to 1,000 μF 6.3 to 16 V.DC 150 to 1,000 μF 4.0 to 32 V.DC 6.8 to 330 μF 4.0 to 20 V.DC 22 to 150 μF C9 Size C6 Size 2.5 to 16 V.DC 100 to 820 μF 2.5, 16 V.DC 100 to 560 μF C55 Size B9 Size 6.3 V.DC 220 μF 2.5 V.DC 100 to 560 μF Conductive Polymer Aluminum Solid Capacitors Mounting specifications ● Recommendable reflow soldering Temperature on the surface of capacitor <Peak temperature 250 °C lead free reflow soldering profile> 250 °C 230 °C 220 °C 200 °C 180 °C 40 s max 50 s max 150 °C 120 s max 60 s max Time (sec.) Reflow cycle : 2 max. Temperature on the surface of capacitor <Peak temperature 260 °C lead free reflow soldering profile> 260 °C 230 °C 220 °C 200 °C 180 °C 40 s max 50 s max 150 °C 120 s max 60 s max Time (sec.) Reflow cycle : 1 max. <Soldering with a soldering iron> Tip of a soldering iron : 400±10 °C Working time : 5 sec. max <Flow soldering> Temperature 120 °C or less (ambient temperature) Preheating Soldering condition 260 °C+5 °C or less Time Flow number 120 sec. or less 1 time 10+1 sec. or less 2 times or less ✽1 ✽1 When soldering 2 times, total immersion time should be 10+1 sec. or less. ● Land pattern c Unit : mm a b Size code A5 B45 B6 C5 C55 C6 C10 E7 E12 F8 F12 a 1.0 1.4 1.4 2.1 2.1 2.1 2.1 2.8 2.8 4.3 4.3 b 6.2 7.4 7.4 9.1 9.1 9.1 9.1 11.1 11.1 13.1 13.1 c 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.9 1.9 1.9 1.9 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Explanation of part numbers Part number system ・Surface mount type SVPK ・Radial lead type Conductive Polymer Aluminum Solid Capacitors Packing specifications ● SMD type (Taping) <Carrier tape> 4.0±0.1 2.0±0.1 +0.1 f1.5−0 E t W F (Polarity) B (−) (+) Mounting parts T Direction of unreeling A P Unit : mm Dimension Size code A5 B45 B6 C5 C55 C6 C10 E7 E12 F8 F12 A±0.2 B±0.2 W±0.3 F±0.1 E±0.1 P±0.1 t±0.1 T±0.2 4.7 5.6 5.6 6.9 6.9 6.9 7.0 8.6 8.6 10.7 10.7 4.7 5.6 5.6 6.9 6.9 6.9 7.0 8.6 8.6 10.7 10.7 12.0 16.0 16.0 16.0 16.0 16.0 24.0 24.0 24.0 24.0 24.0 5.5 7.5 7.5 7.5 7.5 7.5 11.5 11.5 11.5 11.5 11.5 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 1.75 8.0 8.0 8.0 12.0 12.0 12.0 16.0 12.0 16.0 16.0 16.0 0.4 0.4 0.4 0.4 0.4 0.4 0.5 0.4 0.5 0.4 0.4 5.8 4.8 6.2 5.3 6.2 6.2 10.5 7.2 12.3 8.2 13.0 ● Minimum packing quantity and weight <Reel> Direction of unreeling W2 W1 2.0±0.5 f80.0±1.0 f13.0±0.2 f21.0±0.8 R1.0 W1 W2 f380±2.0 Size code A5 B45 B6 C5 C55 C6 C10 E7 E12 F8 F12 Quantity (pcs./Reel, f380) Typical weight (g) 2000 700 2500 900 1500 800 1300 800 1000 800 1000 800 500 700 1000 1100 400 800 500 1000 400 1000 Unit : mm Size code A5, B45 B6, C5, C55, C6 C10, E7, F8, E12, F12 W1±0.5 13.0 17.0 25.0 W2±1.0 17.5 21.5 29.5 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors ● Radial lead type <Applicationsl> ✽ The following table is a standard specification. Please contact us separately concerming specifications except for that mentioned below. Because of a limit on the length of a model name, the part of process name changes to +S from +TSS, +D from +TS, +3 from +C3, Please contact us for details. Series Size code SEP, SEQP SEPC, SEPF SXE B9, C55, C6, C9, E7, E9, E12 E13 F8, F13 Bag-packed product (lead terminal cutting) Not processed Straight cut ◯ +C3 ◯ +C3 ◯ +C3 Taping +TSS (+S) +TS (+D) +T <Lead terminal cutting> Lead terminal cutting code Process names Size code (fD) Dimensions +C3 (+3) Straight cut B9 (f5) C55, C6, C9 (f6.3) E7, E9, E12, E13 (f8) F8, F13 (f10) F±1.0 Unit : mm C3 3.5 L L±0.5 Size code F B9 2.0 Unit : mm C55, C6, C9 E7, E9, E12, E13 2.5 3.5 F8, F13 5.0 <Lead terminal taping> Size code (fD) Taping P2 H W1 W2 P1 F P0 P2 W0 F8, F13 (f10) L F=5.0 mm k +T Δh P fD0 W F Hold-down tape t Taping code Carrier tape Δh P2 t Hold-down tape Carrier tape Δh fD0 P0 W H W1 W0 W2 F t P1 k B9 (f5) C55, C6, C9 (f6.3) E7, E9, E12 (f8) fD0 P L F=2.0 mm F=2.5 mm F=3.5 mm +TSS (+S) W0 F P0 W P1 E13 (f8) k F=3.5 mm L +TS (+D) W1 W2 H P Hold-down tape Carrier tape Unit : mm +0.8 −0.2 Code F 5.0 +T f10 3.5 +TS (+D) f8 2.0 f5 +TSS f6.3 2.5 (+S) 3.5 f8 P±1.0 12.7 12.7 12.7 12.7 12.7 P0±0.2 12.7 12.7 12.7 12.7 12.7 P1±0.5 3.85 4.60 5.35 5.10 4.60 P2±1.0 Δh±1.0 W±0.5 W0 (min.) W1±0.5 W2 (max.) 6.35 0 18.0 9.5 9.0 2.5 6.35 0 18.0 9.5 9.0 2.5 6.35 0 18.0 9.5 9.0 2.5 6.35 0 18.0 9.5 9.0 2.5 6.35 0 18.0 9.5 9.0 2.5 H±0.75 fD0±0.2 t±0.3 k (max.) 18.5 4.0 0.6 0 17.5 4.0 0.6 0 17.5 4.0 0.6 0 17.5 4.0 0.6 0 17.5 4.0 0.6 0 L (max.) 11.0 11.0 11.0 11.0 11.0 Minimum packing quantity and weight Size code Case size B9 C55 C6 C9 E7 f5 f6.3 f6.3 f6.3 f8 Processed type discrete lead terminals Zig-zag pack taping type Quantity Typical weight Quantity Typical weight (pcs./Bag) (g) (pcs./Bag) (g) 500 180 2000 1000 500 150 1500 650 500 160 1500 700 500 240 1500 1000 200 110 1000 820 Size code Case size E9 E12 E13 F8 F13 f8 f8 f8 f10 f10 Processed type discrete lead terminals Zig-zag pack taping type Quantity Typical weight Quantity Typical weight (pcs./Bag) (g) (pcs./Bag) (g) 200 130 1000 900 200 200 1000 980 200 160 1000 1060 200 180 500 890 200 280 500 940 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 NEW Conductive Polymer Aluminum Solid Capacitors Surface Mount Type Series : SXV Features ● Super ● RoHS high voltage (100 V.DC max.) compliance, Halogen free Specifications Size code Category temperature range Rated voltage range Rated capacitance range Capacitance tolerance Leakage current Dissipation factor (tan d) Endurance Damp heat (Steady State) E12 –55 °C to +105 °C 63 V.DC to 100 V.DC 15 µF to 33 µF ±20 % (120 Hz / + 20 °C) Please see the attached characteristics list Please see the attached characteristics list +105 °C, 5000 h, rated voltage applied Capacitance change Within ±20 % of the initial value tan d < 150 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Marking Dimensions (not to scale) 0.2 max. W – C H fD P Polarity marking (−) Lot. No. Series + L R R. Capacitance Unit : mm R. Voltage Size code fD±0.5 E12 8.0 L +0.1 −0.4 11.9 W±0.2 H±0.2 C±0.2 8.3 8.3 9.0 R P±0.2 0.8 to 1.1 3.2 ✽ Externals of figure are the reference. Characteristics list Rated Rated Series voltage capacitance (V.DC) (µF) SXV 63 100 33 15 Case size (mm) fD L 8.0 8.0 11.9 11.9 Size code E12 Specifications Ripple ✽1 ESR ✽2 current tan d ✽3 (mΩ max.) (mAr.m.s.) 2950 25 0.12 2350 40 0.12 LC ✽4 (µA) 104 75 Standard (Reel size : f380) Min. Packaging Q'ty Part number (pcs) 63SXV33M 400 100SXV15M 400 ✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency 120 Hz < f < 1 kHz 1 kHz < f < 10 kHz 10 kHz < f < 100 kHz 100 kHz < f < 500 kHz Coefficient 0.05 0.3 0.7 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Surface Mount Type Series : SVPG Features ● Low profile (Height 4.5 mm max.) ESR (8 mΩ to 30 mΩ) ● RoHS compliance, Halogen free ● Low Specifications Size code Category temperature range Rated voltage range Rated capacitance range Capacitance tolerance Leakage current Dissipation factor (tan d) Endurance Damp heat (Steady State) B45 C10 –55 °C to +105 °C 16 V.DC to 25 V.DC 15 µF to 47 µF 16 V.DC 270 µF ±20 % (120 Hz / + 20 °C) Please see the attached characteristics list Please see the attached characteristics list +105 °C, 5000 h, rated voltage applied Capacitance change Within ±20 % of the initial value tan d < 150 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Marking Dimensions (not to scale) 0.2 max. W – Series + L R. Capacitance R. Voltage Size code fD±0.5 B45 C10 5.0 6.3 C H fD P Polarity marking (−) Lot. No. L +0.1 −0.4 R W±0.2 H±0.2 C±0.2 4.4 9.9 5.3 6.6 5.3 6.6 6.0 7.3 Unit : mm R P±0.2 0.6 to 0.8 0.6 to 0.8 1.4 2.1 ✽ Externals of figure are the reference. Characteristics list Rated Rated Series voltage capacitance (V.DC) (µF) 16 SVPG 20 25 47 270 33 15 Case size (mm) fD L 5.0 6.3 5.0 5.0 4.4 9.9 4.4 4.4 Specifications Size code B45 C10 B45 ✽1 Ripple ESR ✽2 current tan d ✽3 (mΩ max.) (mAr.m.s.) 3200 25 0.12 5800 8 0.12 3000 27 0.12 2800 30 0.12 LC ✽4 (µA) 150 864 132 75 Standard (Reel size : f380) Min. Packaging Q'ty Part number (pcs) 16SVPG47M 2500 16SVPG270M 500 20SVPG33M 2500 25SVPG15M 2500 ✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency Coefficient 120 Hz < f < 1 kHz 0.05 1 kHz < f < 10 kHz 0.3 10 kHz < f < 100 kHz 0.7 100 kHz < f < 500 kHz 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Surface Mount Type Series : SVPF Features ● High voltage (50 V.DC max.) capacitance (1000 μF max.) ● 105 °C 5000 h ● RoHS compliance, Halogen free ● Large Specifications Size code B6 C6 E7 E12 Category temperature range –55 °C to +105 °C Rated voltage range 16 V.DC to 25 V.DC 16 V.DC to 50 V.DC Rated capacitance range 27 μF to 82 μF 10 μF to 180 μF 18 μF to 270 μF 39 μF to 560 μF Capacitance tolerance ±20 % (120 Hz / + 20 °C) Leakage current Please see the attached characteristics list Dissipation factor (tan d) Please see the attached characteristics list +105 °C, 5000 h, rated voltage applied Capacitance change Within ±20 % of the initial value Endurance tan d < 150 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value Damp heat (Steady State) tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Marking F12 68 μF to 1000 μF Dimensions (not to scale) 0.2 max. W C H fD P – Polarity marking (−) Lot. No. + L R Unit : mm Series R. Capacitance R. Voltage Size code fD±0.5 B6 C6 E7 E12 F12 5.0 6.3 8.0 8.0 10.0 L +0.1 −0.4 5.9 5.9 6.9 11.9 12.6 W±0.2 H±0.2 C±0.2 5.3 6.6 8.3 8.3 10.3 5.3 6.6 8.3 8.3 10.3 6.0 7.3 9.0 9.0 11.0 R P±0.2 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 0.8 to 1.1 0.8 to 1.1 1.4 2.1 3.2 3.2 4.6 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Characteristics list Rated Rated Series voltage capacitance (V.DC) (μF) 16 20 SVPF 25 35 50 82 180 270 560 1000 56 120 180 390 560 27 47 56 82 100 180 330 22 39 82 120 10 18 39 68 Case size (mm) fD L 5.0 6.3 8.0 8.0 10.0 5.0 6.3 8.0 8.0 10.0 5.0 6.3 6.3 8.0 8.0 8.0 10.0 6.3 8.0 8.0 10.0 6.3 8.0 8.0 10.0 5.9 5.9 6.9 11.9 12.6 5.9 5.9 6.9 11.9 12.6 5.9 5.9 5.9 6.9 6.9 11.9 12.6 5.9 6.9 11.9 12.6 5.9 6.9 11.9 12.6 Size code B6 C6 E7 E12 F12 B6 C6 E7 E12 F12 B6 C6 E7 E12 F12 C6 E7 E12 F12 C6 E7 E12 F12 Specifications Ripple ✽1 ESR ✽2 current tan d ✽3 (mΩ max.) (mAr.m.s.) 3000 27 0.12 3300 22 0.12 3300 22 0.12 4950 14 0.12 5400 12 0.12 2800 30 0.12 3200 25 0.12 3200 25 0.12 4950 14 0.12 5400 12 0.12 2450 40 0.12 2800 30 0.12 2800 30 0.12 3000 28 0.12 3200 24 0.12 4650 16 0.12 5000 14 0.12 2600 35 0.12 2800 30 0.12 4000 20 0.12 4400 18 0.12 2500 40 0.12 2700 35 0.12 3800 25 0.12 4300 20 0.12 LC ✽4 (μA) 262 576 864 1792 3200 224 480 720 1560 2240 135 235 280 410 500 900 1650 154 273 574 840 100 180 390 680 Standard (Reel size : f380) Min. Packaging Q'ty Part number (pcs) 16SVPF82M 1500 16SVPF180M 1000 16SVPF270M 1000 16SVPF560M 400 16SVPF1000M 400 20SVPF56MX 1500 20SVPF120M 1000 20SVPF180M 1000 20SVPF390M 400 20SVPF560M 400 25SVPF27MX 1500 25SVPF47M 1000 25SVPF56M 1000 25SVPF82M 1000 25SVPF100M 1000 25SVPF180M 400 25SVPF330M 400 35SVPF22M 1000 35SVPF39M 1000 35SVPF82M 400 35SVPF120M 400 50SVPF10M 1000 50SVPF18M 1000 50SVPF39M 400 50SVPF68M 400 ✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency 120 Hz < f < 1 kHz 1 kHz < f < 10 kHz 10 kHz < f < 100 kHz 100 kHz < f < 500 kHz Coefficient 0.05 0.3 0.7 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Surface Mount Type Series : SVPE Features ● Super low ESR (8 mΩ to 18 mΩ) capacitance (1200 μF max.) ● RoHS compliance, Halogen free ● Large Specifications Size code B6 C6 C10 Category temperature range –55 °C to +105 °C Rated voltage range 2.5 V.DC to 6.3 V.DC 2.5 V.DC to 10 V.DC 2 V.DC to 16 V.DC Rated capacitance range 150 μF to 390 μF 220 μF to 390 μF 180 μF to 1200 μF Capacitance tolerance ±20 % (120 Hz / + 20 °C) Leakage current Please see the attached characteristics list Dissipation factor (tan d) Please see the attached characteristics list +105 °C, 2000 h, rated voltage applied Capacitance change Within ±20 % of the initial value Endurance tan d < 150 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value Damp heat (Steady State) tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Marking F12 16 V.DC 470 μF Dimensions (not to scale) 0.2 max. W H fD Polarity marking (−) Lot. No. + L Series Size code R. Capacitance B6 C6 C10 F12 R. Voltage fD±0.5 5.0 6.3 6.3 10.0 C P – L +0.1 −0.4 5.9 5.9 9.9 12.6 R Unit : mm W±0.2 H±0.2 C±0.2 R P±0.2 5.3 5.3 6.0 0.6 to 0.8 1.4 6.6 6.6 7.3 0.6 to 0.8 2.1 6.6 6.6 7.3 0.6 to 0.8 2.1 10.3 10.3 11.0 0.8 to 1.1 4.6 ✽ Externals of figure are the reference. Characteristics list Rated Rated Series voltage capacitance (V.DC) (μF) 2 2.5 1200 270 330 390 SVPE 6.3 150 180 220 10 16 220 180 470 Case size (mm) fD L 6.3 5.0 5.0 5.0 5.0 6.3 5.0 5.0 5.0 6.3 6.3 6.3 10.0 9.9 5.9 5.9 5.9 5.9 5.9 5.9 5.9 5.9 5.9 5.9 9.9 12.6 Specifications Size Ripple ✽1 ESR code current 100 kHz/20 °C 300 kHz/20 °C tan d ✽2 (mAr.m.s.) (mΩ max.) (mΩ max.) C10 5230 8 8 0.12 3860 10 9 0.12 3150 15 13 0.12 B6 3860 10 9 0.12 3860 10 9 0.12 C6 3900 10 9 0.12 3520 12 10 0.12 3150 15 13 0.12 B6 3150 15 13 0.12 3900 10 9 0.12 C6 2700 20 18 0.12 C10 4460 11 10 0.12 F12 6100 10 9 0.12 ✽3 LC (μA) 500 500 500 500 700 500 500 500 500 500 500 576 1504 Standard (Reel size : f380) Min. Packaging Q'ty Part number (pcs) 2SVPE1200M 500 2R5SVPE270M 1500 2R5SVPE330M 1500 2R5SVPE330MY 1500 2R5SVPE390MX 1500 2R5SVPE390M 1000 6SVPE150M 1500 6SVPE180M 1500 6SVPE220MW 1500 6SVPE220M 1000 10SVPE220M 1000 16SVPE180M 500 16SVPE470M 400 ✽1 Ripple current (100 kHz/ +105 °C ), ✽2 tan d (120 Hz/+20 °C) ✽3 After 2 minutes ◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency Coefficient 120 Hz < f < 1 kHz 0.05 1 kHz < f < 10 kHz 0.3 10 kHz < f < 100 kHz 0.7 100 kHz < f < 500 kHz 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Surface Mount Type Series : SVPD Features ● 125 °C 2000 h ● Guaranteed at 85 °C 85 % ● RoHS compliance, Halogen free Specifications Size code C6 E7 F8 E12 Category temperature range –55 °C to +125 °C Rated voltage range 10 V.DC to 25 V.DC 16 V.DC to 35 V.DC 25 V.DC to 35 V.DC Rated capacitance range 10 µF to 56 µF 8.2 µF to 82 µF 18 µF to 39 µF 22 µF to 47 µF Capacitance tolerance ±20 % (120 Hz / + 20 °C) Leakage current Please see the attached characteristics list Dissipation factor (tan d) Please see the attached characteristics list +125 °C, 2000 h, rated voltage applied Capacitance change Within ±20 % of the initial value Endurance tan d < 200 % of the initial limit DC leakage current Within the initial limit +85 °C, 85 % to 90 %, 1000 h, rated voltage applied Capacitance change Within ±20 % of the initial value Damp heat (Steady State) tan d < 200 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Marking F12 47 µF to 82 µF Dimensions (not to scale) 0.2 max. W H fD Polarity marking (−) Lot. No. + L Series Size code R. Capacitance C6 E7 F8 E12 F12 R. Voltage fD±0.5 6.3 8.0 10.0 8.0 10.0 C P – L +0.1 −0.4 5.9 6.9 7.9 11.9 12.6 R Unit : mm W±0.2 H±0.2 C±0.2 R P±0.2 6.6 6.6 7.3 0.6 to 0.8 2.1 8.3 8.3 9.0 0.6 to 0.8 3.2 10.3 10.3 11.0 0.6 to 0.8 4.6 8.3 8.3 9.0 0.8 to 1.1 3.2 10.3 10.3 11.0 0.8 to 1.1 4.6 ✽ Externals of figure are the reference. Characteristics list Rated Rated Series voltage capacitance (V.DC) (µF) 10 16 25 SVPD 35 56 82 10 22 39 47 82 8.2 18 22 47 Case size (mm) fD L 6.3 8.0 6.3 8.0 10.0 8.0 10.0 8.0 10.0 8.0 10.0 5.9 6.9 5.9 6.9 7.9 11.9 12.6 6.9 7.9 11.9 12.6 Specifications Size Ripple ✽1 Allowable ✽1 ✽2 code current ripple current ESR tan d ✽3 (mΩ max.) (mAr.m.s.) (mAr.m.s.) C6 538 1700 45 0.12 E7 670 2120 40 0.12 C6 474 1500 65 0.10 E7 580 1835 48 0.10 F8 664 2100 45 0.10 E12 943 2980 30 0.12 F12 1202 3800 28 0.12 E7 400 1300 70 0.10 F8 550 1800 60 0.10 E12 700 2300 50 0.12 F12 1150 3650 30 0.12 ✽4 LC (µA) 112 262 50 110 195 235 410 57 126 154 329 Standard (Reel size : f380) Min. Part number Packaging Q'ty (pcs) 10SVPD56M 1000 16SVPD82M 1000 25SVPD10M 1000 25SVPD22M 1000 25SVPD39M 500 25SVPD47M 400 25SVPD82M 400 35SVPD8R2M 1000 35SVPD18M 500 35SVPD22M 400 35SVPD47M 400 ✽1 Ripple current (100 kHz/ +105 °C < Tx < 125 °C), Allowable ripple current (100 kHz / Tx < 105 °C) ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency Coefficient 120 Hz < f < 1 kHz 0.05 1 kHz < f < 10 kHz 0.3 10 kHz < f < 100 kHz 0.7 100 kHz < f < 500 kHz 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Surface Mount Type Series : SVPC Features ● Low ESR (9 mΩ to 30 mΩ) capacitance (2700 μF max.) ● RoHS compliance, Halogen free ● Large Specifications Size code B6 C6 E7 E12 Category temperature range –55 °C to +105 °C Rated voltage range 2.5 V.DC to 16 V.DC Rated capacitance range 39 μF to 180 μF 68 μF to 560 μF 120 μF to 680 μF 270 μF to 1500 μF Capacitance tolerance ±20 % (120 Hz / + 20 °C) Leakage current Please see the attached characteristics list Dissipation factor (tan d) Please see the attached characteristics list +105 °C, 2000 h, rated voltage applied Capacitance change Within ±20 % of the initial value Endurance tan d < 150 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value Damp heat (Steady State) tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Marking F12 2.5 V.DC 2700 μF Dimensions (not to scale) 0.2 max. W Polarity marking (−) Lot. No. C H fD P – + L R Series R. Capacitance R. Voltage Unit : mm Size code fD±0.5 B6 C6 E7 E12 F12 5.0 6.3 8.0 8.0 10.0 L +0.1 −0.4 5.9 5.9 6.9 11.9 12.6 W±0.2 H±0.2 C±0.2 5.3 6.6 6.9 11.9 10.3 5.3 6.6 6.9 11.9 10.3 6.0 7.3 9.0 9.0 11.0 R P±0.2 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 0.8 to 1.1 0.8 to 1.1 1.4 2.1 3.2 3.2 4.6 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Characteristics list Rated Rated Series voltage capacitance (V.DC) (μF) 180 390 2.5 560 680 820 1500 2700 150 4.0 330 560 1200 1500 100 SVPC 120 6.3 220 330 390 820 68 10 120 270 330 39 68 16 100 120 150 270 Case size (mm) fD L 5.0 5.0 5.0 6.3 6.3 6.3 8.0 8.0 8.0 10.0 5.0 5.0 5.0 6.3 6.3 6.3 8.0 8.0 8.0 8.0 5.0 5.0 5.0 6.3 6.3 6.3 8.0 8.0 5.0 5.0 6.3 6.3 8.0 8.0 5.0 5.0 6.3 6.3 6.3 8.0 8.0 8.0 5.9 5.9 5.9 5.9 5.9 5.9 6.9 11.9 11.9 12.6 5.9 5.9 5.9 5.9 5.9 5.9 6.9 11.9 11.9 11.9 5.9 5.9 5.9 5.9 5.9 5.9 6.9 11.9 5.9 5.9 5.9 5.9 6.9 6.9 5.9 5.9 5.9 5.9 5.9 6.9 6.9 11.9 Specifications Size Ripple ✽1 ESR code current 100 kHz/20 °C 300 kHz/20 °C tan d ✽2 (mAr.m.s.) (mΩ max.) (mΩ max.) 1970 30 26 0.12 B6 2200 24 20 0.12 2800 19 16 0.12 2410 25 22 0.12 C6 3160 15 13 0.12 3500 16 14 0.12 E7 3370 20 17 0.12 5380 9 8 0.15 E12 5150 10 9 0.15 F12 5070 12 10 0.15 1970 30 26 0.12 B6 2240 23 20 0.12 2730 20 17 0.12 2320 27 23 0.12 C6 2630 21 18 0.12 3160 15 13 0.12 E7 3220 22 19 0.12 5380 9 8 0.15 E12 4700 12 10 0.15 4700 12 10 0.15 1970 21 18 0.12 B6 2150 30 26 0.12 2660 25 21 0.12 2320 27 23 0.12 C6 3160 15 13 0.12 3390 17 15 0.12 E7 3220 22 19 0.12 E12 4700 12 10 0.15 1970 30 26 0.12 B6 2540 23 20 0.12 2320 27 23 0.12 C6 2600 22 19 0.12 3220 22 19 0.12 E7 3460 19 17 0.12 1820 35 30 0.12 B6 2350 27 23 0.12 2200 30 26 0.12 C6 2440 25 22 0.12 2490 24 23 0.12 2900 27 23 0.12 E7 3220 22 21 0.12 E12 4070 16 14 0.15 LC ✽3 (μA) 300 300 300 300 300 300 500 500 750 1350 300 300 300 300 300 300 500 500 960 1200 300 300 300 300 300 415 491 1033 300 300 300 300 500 660 300 300 300 300 300 500 500 864 Standard (Reel size : f380) Min. Packaging Q'ty Part number (pcs) 2R5SVPC180M 1500 2R5SVPC180MY 1500 2R5SVPC180MV 1500 2R5SVPC390M 1000 2R5SVPC390MV 1000 2R5SVPC560M 1000 2R5SVPC680M 1000 2R5SVPC820M 400 2R5SVPC1500M 400 2R5SVPC2700M 400 4SVPC150M 1500 4SVPC150MY 1500 4SVPC150MV 1500 4SVPC330M 1000 4SVPC330MY 1000 4SVPC330MV 1000 4SVPC560M 1000 4SVPC560MX 400 4SVPC1200M 400 4SVPC1500M 400 6SVPC100M 1500 6SVPC100MY 1500 6SVPC120MV 1500 6SVPC220M 1000 6SVPC220MV 1000 6SVPC330M 1000 6SVPC390M 1000 6SVPC820M 400 10SVPC68M 1500 10SVPC68MV 1500 10SVPC120M 1000 10SVPC120MV 1000 10SVPC270M 1000 10SVPC330M 1000 16SVPC39M 1500 16SVPC39MV 1500 16SVPC68M 1000 16SVPC68MV 1000 16SVPC100M 1000 16SVPC120M 1000 16SVPC150M 1000 16SVPC270M 400 ✽1 Ripple current (100 kHz/ +105 °C ), ✽2 tan d (120 Hz/+20 °C) ✽3 After 2 minutes ◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency Coefficient 120 Hz < f < 1 kHz 0.05 1 kHz < f < 10 kHz 0.3 10 kHz < f < 100 kHz 0.7 100 kHz < f < 500 kHz 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 02 Jun. 2016 Conductive Polymer Aluminum Solid Capacitors Surface Mount Type Series : SVPA Features ● Low ESR (18 mΩ max.) ripple (4240 mA.r.m.s.) ● RoHS compliance, Halogen free ● High Specifications Size code Category temperature range Rated voltage range Rated capacitance range Capacitance tolerance Leakage current Dissipation factor (tan d) Endurance Damp heat (Steady State) B6 C6 E7 F8 –55 °C to +105 °C 2.5 V.DC to 20 V.DC 10 µF to 82 µF 22 µF to 180 µF 47 µF to 330 µF ±20 % (120 Hz / + 20 °C) Please see the attached characteristics list Please see the attached characteristics list +105 °C, 2000 h, rated voltage applied Capacitance change Within ±20 % of the initial value tan d < 150 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Marking 2.5 V.DC to 16 V.DC 180 µF to 820 µF Dimensions (not to scale) 0.2 max. W Polarity marking (−) Lot. No. C H fD P – + L R Series R. Capacitance R. Voltage Unit : mm Size code fD±0.5 B6 C6 E7 F8 5.0 6.3 8.0 10.0 L +0.1 −0.4 5.9 5.9 6.9 7.9 W±0.2 H±0.2 C±0.2 5.3 6.6 8.3 10.3 5.3 6.6 8.3 10.3 6.0 7.3 9.0 11.0 R P±0.2 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 1.4 2.1 3.2 4.6 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Characteristics list Rated Rated Series voltage capacitance (V.DC) (µF) 2.5 4.0 6.3 SVPA 10 82 180 330 820 68 150 270 680 47 120 220 470 68 150 330 39 16 20 82 180 10 22 47 Case size (mm) fD L 5.0 6.3 8.0 10.0 5.0 6.3 8.0 10.0 5.0 6.3 8.0 10.0 6.3 8.0 10.0 6.3 6.3 8.0 10.0 5.0 6.3 8.0 5.9 5.9 6.9 7.9 5.9 5.9 6.9 7.9 5.9 5.9 6.9 7.9 5.9 6.9 7.9 5.9 5.9 6.9 7.9 5.9 5.9 6.9 Size code B6 C6 E7 F8 B6 C6 E7 F8 B6 C6 E7 F8 C6 E7 F8 C6 E7 F8 B6 C6 E7 Specifications Ripple ✽1 ESR ✽2 current tan d ✽3 (mΩ max.) (mAr.m.s.) 1970 30 0.12 2690 20 0.12 3370 20 0.12 4240 19 0.12 1970 30 0.12 2570 22 0.12 3220 22 0.12 4130 20 0.12 1970 30 0.12 2570 22 0.12 3220 22 0.12 4130 20 0.12 2200 30 0.12 2760 30 0.12 3770 24 0.12 2040 35 0.12 2460 24 0.12 2760 30 0.12 3430 29 0.12 1700 40 0.12 2040 35 0.12 2630 33 0.12 LC ✽4 (µA) 300 300 500 500 300 300 500 544 300 300 500 592 300 500 660 300 300 262 576 80 88 188 Standard (Reel size : f380) Min. Packaging Q'ty Part number (pcs) 2R5SVPA82MAA 1500 2R5SVPA180MAA 1000 2R5SVPA330MAA 1000 2R5SVPA820M 500 4SVPA68MAA 1500 4SVPA150MAA 1000 4SVPA270MAA 1000 4SVPA680M 500 6SVPA47MAA 1500 6SVPA120MAA 1000 6SVPA220MAA 1000 6SVPA470M 500 10SVPA68MAA 1000 10SVPA150MAA 1000 10SVPA330M 500 16SVPA39MAA 1000 16SVPA39MAAY 1000 16SVPA82MAA 1000 16SVPA180M 500 20SVPA10M 1500 20SVPA22M 1000 20SVPA47M 1000 ✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency 120 Hz < f < 1 kHz 1 kHz < f < 10 kHz 10 kHz < f < 100 kHz 100 kHz < f < 500 kHz Coefficient 0.05 0.3 0.7 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Surface Mount Type Series : SVPB Features ● Low profile (Height 5 mm max.) compliance, Halogen free ● RoHS Specifications Size code Category temperature range Rated voltage range Rated capacitance range Capacitance tolerance Leakage current Dissipation factor (tan d) Endurance Damp heat (Steady State) C5 C55 –55 °C to +105 °C 2.5 V.DC to 20 V.DC 15 µF to 120 µF 20 V.DC 22 µF ±20 % (120 Hz / + 20 °C) Please see the attached characteristics list Please see the attached characteristics list +105 °C, 1000 h, rated voltage applied Capacitance change Within ±20 % of the initial value (±30 % for C5 size) tan d < 150 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Marking Dimensions (not to scale) 0.2 max. W – Series + L R. Capacitance R. Voltage Size code fD±0.5 C5 C55 6.3 6.3 C H fD P Polarity marking (−) Lot. No. L +0.1 −0.4 R W±0.2 H±0.2 C±0.2 4.9 5.4 6.6 6.6 6.6 6.6 7.3 7.3 Unit : mm R P±0.2 0.6 to 0.8 0.6 to 0.8 2.1 2.1 ✽ Externals of figure are the reference. Characteristics list Rated Rated Series voltage capacitance (V.DC) (µF) SVPB 2.5 4.0 6.3 10 16 20 120 100 82 56 33 15 22 Case size (mm) fD L 6.3 6.3 6.3 6.3 6.3 6.3 6.3 4.9 4.9 4.9 4.9 4.9 4.9 5.4 Size code C5 C55 Specifications Ripple ✽1 ESR ✽2 current tan d ✽3 (mΩ max.) (mAr.m.s.) 1670 40 0.12 1670 40 0.12 1670 40 0.12 1670 40 0.12 1670 40 0.12 2000 45 0.12 2000 35 0.12 LC ✽4 (µA) 120 160 207 224 211 120 88 Standard (Reel size : f380) Min. Packaging Q'ty Part number (pcs) 2R5SVPB120M 1300 4SVPB100M 1300 6SVPB82M 1300 10SVPB56M 1300 16SVPB33M 1300 20SVPB15M 1300 20SVPB22M 1000 ✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency 120 Hz < f < 1 kHz 1 kHz < f < 10 kHz 10 kHz < f < 100 kHz 100 kHz < f < 500 kHz Coefficient 0.05 0.3 0.7 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Surface Mount Type Series : SVPS Features ● 105 °C 5000 h compliance, Halogen free ● RoHS Specifications Size code A5 B6 C6 E7 F8 Category temperature range –55 °C to +105 °C Rated capacitance range 4 V.DC to 10 V.DC 4 V.DC to 16 V.DC 4 V.DC to 20 V.DC 4 V.DC to 25 V.DC 4 V.DC to 16 V.DC Rated capacitance range 10 µF to 33 µF 22 µF to 68 µF 22 µF to 150 µF 10 µF to 270 µF 100 µF to 680 µF Capacitance tolerance ±20 % (120 Hz / + 20 °C) Leakage current Please see the attached characteristics list Dissipation factor (tan d) Please see the attached characteristics list +105 °C, 5000 h, rated voltage applied (25 V.DC → 20 V.DC applied) Capacitance change Within ±20 % of the initial value Endurance tan d < 150 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value Damp heat (Steady State) tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Marking Dimensions (not to scale) 0.2 max. W Polarity marking (−) Lot. No. C H fD P – + L R Series R. Capacitance R. Voltage Unit : mm Size code fD±0.5 +0.1 L −0.4 A5 B6 C6 E7 F8 4.0 5.0 6.3 8.0 10.0 5.4 5.9 5.9 6.9 7.9 W±0.2 H±0.2 C±0.2 4.3 5.3 6.6 8.3 10.3 4.3 5.3 6.6 8.3 10.3 5.0 6.0 7.3 9.0 11.0 R P±0.2 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 1.0 1.4 2.1 3.2 4.6 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Characteristics list Rated Rated Series voltage capacitance (V.DC) (µF) 4.0 6.3 SVPS 10 33 68 150 270 680 22 47 120 220 470 10 15 33 68 150 16 20 25 330 22 39 82 100 180 22 47 10 Case size (mm) fD L 4.0 5.0 6.3 8.0 10.0 4.0 5.0 6.3 8.0 10.0 4.0 4.0 5.0 6.3 8.0 10.0 10.0 5.0 6.3 8.0 10.0 10.0 6.3 8.0 8.0 5.4 5.9 5.9 6.9 7.9 5.4 5.9 5.9 6.9 7.9 5.4 5.4 5.9 5.9 6.9 7.9 7.9 5.9 5.9 6.9 7.9 7.9 5.9 6.9 6.9 Size code A5 B6 C6 E7 F8 A5 B6 C6 E7 F8 A5 B6 C6 E7 F8 B6 C6 E7 F8 C6 E7 Specifications Ripple ✽1 ESR ✽2 current tan d ✽3 (mΩ max.) (mAr.m.s.) 740 200 0.15 1970 30 0.12 2570 22 0.12 3220 22 0.12 4130 20 0.12 740 200 0.12 1970 30 0.12 2570 22 0.12 3220 22 0.12 4130 20 0.12 700 220 0.10 740 200 0.10 1100 70 0.12 2200 30 0.12 2760 30 0.12 3020 30 0.12 3770 24 0.12 1060 90 0.10 2460 24 0.12 2760 30 0.12 2670 35 0.12 3430 29 0.12 1450 60 0.10 1890 45 0.12 1500 60 0.10 LC ✽4 (µA) 66 300 300 500 544 69.3 300 300 500 592 50 75 165 300 500 300 660 176 300 262 320 576 88 188 125 Standard (Reel size : f380) Min. Packaging Q'ty Part number (pcs) 4SVPS33M 2000 4SVPS68M 1500 4SVPS150M 1000 4SVPS270M 1000 4SVPS680M 500 6SVPS22M 2000 6SVPS47M 1500 6SVPS120M 1000 6SVPS220M 1000 6SVPS470M 500 10SVPS10M 2000 10SVPS15M 2000 10SVPS33M 1500 10SVPS68M 1000 10SVPS150MX 1000 10SVPS150M 500 10SVPS330M 500 16SVPS22M 1500 16SVPS39M 1000 16SVPS82M 1000 16SVPS100M 500 16SVPS180M 500 20SVPS22M 1000 20SVPS47M 1000 25SVPS10M 1000 ✽1 Ripple current (100 kHz/ +105 °C ), : The surface temperature of aluminum case top must not exceed 105 °C. A rise in temperature due to self-heating by ripple current should be factored in. ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency 120 Hz < f < 1 kHz 1 kHz < f < 10 kHz 10 kHz < f < 100 kHz 100 kHz < f < 500 kHz Coefficient 0.05 0.3 0.7 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Surface Mount Type Series : SVQP Features ● 125 °C 1000 h compliance, Halogen free ● RoHS Specifications Size code Category temperature range Rated voltage range Rated capacitance range Capacitance tolerance Leakage current Dissipation factor (tan d) Endurance Damp heat (Steady State) C6 E7 –55 °C to +125 °C 4 V.DC to 20 V.DC 22 µF to 150 µF 6.3 V.DC to 20 V.DC 47 µF to 220 µF ±20 % (120 Hz / + 20 °C) Please see the attached characteristics list Please see the attached characteristics list +125 °C, 1000 h, rated voltage applied Capacitance change Within ±20 % of the initial value tan d < 200 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Marking Dimensions (not to scale) 0.2 max. Series + L R. Capacitance Size code fD±0.5 R. Voltage C6 E7 6.3 8.0 C H fD P Polarity marking (−) Lot. No. W – L +0.1 −0.4 5.9 6.9 R W±0.2 H±0.2 C±0.2 6.6 8.3 6.6 8.3 7.3 9.0 Unit : mm R P±0.2 0.6 to 0.8 0.6 to 0.8 2.1 3.2 ✽ Externals of figure are the reference. Characteristics list Rated Rated Series voltage capacitance (V.DC) (µF) 4.0 6.3 SVQP 10 16 20 150 82 100 220 56 120 150 39 82 22 47 Case size (mm) fD L 6.3 6.3 6.3 8.0 6.3 8.0 8.0 6.3 8.0 6.3 8.3 5.9 5.9 5.9 6.9 5.9 6.9 6.9 5.9 6.9 5.9 6.9 Specifications Size Ripple ✽1 Allowable ✽1 ✽2 code current ripple current ESR tan d ✽3 (mΩ max.) (mAr.m.s.) (mAr.m.s.) 572 1810 40 0.12 C6 538 1700 45 0.12 572 1810 40 0.12 E7 810 2560 35 0.12 C6 538 1700 45 0.12 810 2560 35 0.12 E7 810 2560 35 0.12 C6 512 1620 50 0.10 E7 670 2120 40 0.12 C6 459 1450 60 0.10 E7 598 1890 45 0.12 ✽4 LC (µA) 300 258 315 693 280 600 750 312 656 220 470 Standard (Reel size : f380) Min. Part number Packaging Q'ty (pcs) 4SVQP150M 1000 6SVQP82M 1000 6SVQP100M 1000 6SVQP220M 1000 10SVQP56M 1000 10SVQP120M 1000 10SVQP150M 1000 16SVQP39M 1000 16SVQP82M 1000 20SVQP22M 1000 20SVQP47M 1000 ✽1 Ripple current (100 kHz/ +105 °C < Tx < 125 °C), Allowable ripple current (100 kHz / Tx < 105 °C) ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency Coefficient 120 Hz < f < 1 kHz 0.05 1 kHz < f < 10 kHz 0.3 10 kHz < f < 100 kHz 0.7 100 kHz < f < 500 kHz 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Surface Mount Type Series : SVP Features ● Standard ● Wealth ● RoHS models compliance, Halogen free Specifications Size code A5 B6 C6 E7 F8 E12 F12 Category temperature range –55 °C to +105 °C Rated voltage range 4 V.DC to 16 V.DC 4 V.DC to 20 V.DC 2.5 V.DC to 20 V.DC 4 V.DC to 20 V.DC 2.5 V.DC to 20 V.DC Rated capacitance range 3.3 µF to 33 µF 10 µF to 68 µF 22 µF to 220 µF 33 µF to 330 µF 56 µF to 680 µF 100 µF to 680 µF 150 µF to 1500 µF Capacitance tolerance ±20 % (120 Hz / + 20 °C) Leakage current Please see the attached characteristics list Dissipation factor (tan d) Please see the attached characteristics list +105 °C, 2000 h, rated voltage applied Capacitance change Within ±20 % of the initial value Endurance tan d < 150 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value Damp heat (Steady State) tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Marking Dimensions (not to scale) 0.2 max. W Polarity marking (−) Lot. No. Series R. Capacitance R. Voltage + L Size code fD±0.5 A5 B6 C6 E7 F8 E12 F12 4.0 5.0 6.3 8.0 10.0 8.0 10.0 C H fD P – L +0.1 −0.4 5.4 5.9 5.9 6.9 7.9 11.9 12.6 R W±0.2 H±0.2 C±0.2 4.3 5.3 6.6 8.3 10.3 8.3 10.3 4.3 5.3 6.6 8.3 10.3 8.3 10.3 5.0 6.0 7.3 9.0 11.0 9.0 11.0 Unit : mm R P±0.2 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 0.6 to 0.8 0.8 to 1.1 0.8 to 1.1 1.0 1.4 2.1 3.2 4.6 3.2 4.6 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Characteristics list Rated Rated Series voltage capacitance (V.DC) (µF) 2.5 4.0 6.3 220 680 1500 33 39 68 150 330 560 680 1200 22 47 82 100 120 220 330 470 SVP 10 820 4.7 6.8 10 15 33 47 56 120 150 270 330 16 560 3.3 15 22 39 56 82 100 150 180 20 330 10 22 27 33 47 56 68 100 150 Case size (mm) fD L 6.3 8.0 10.0 4.0 5.0 5.0 6.3 8.0 8.0 10.0 10.0 4.0 5.0 6.3 6.3 6.3 8.0 10.0 10.0 10.0 8.0 10.0 4.0 4.0 4.0 4.0 5.0 6.3 6.3 8.0 8.0 10.0 10.0 10.0 8.0 10.0 4.0 5.0 5.0 6.3 8.0 8.0 10.0 10.0 10.0 8.0 10.0 5.0 6.3 6.3 8.0 8.0 10.0 10.0 8.0 10.0 5.9 11.9 12.6 5.4 5.9 5.9 5.9 6.9 11.9 7.9 12.6 5.4 5.9 5.9 5.9 5.9 6.9 7.9 7.9 7.9 11.9 12.6 5.4 5.4 5.4 5.4 5.9 5.9 5.9 6.9 6.9 7.9 7.9 7.9 11.9 12.6 5.4 5.9 5.9 5.9 6.9 6.9 7.9 7.9 7.9 11.9 12.6 5.9 5.9 5.9 6.9 6.9 7.9 7.9 11.9 12.6 Size code C6 E12 F12 A5 B6 C6 E7 E12 F8 F12 A5 B6 C6 E7 F8 E12 F12 A5 B6 C6 E7 F8 E12 F12 A5 B6 C6 E7 F8 E12 F12 B6 C6 E7 F8 E12 F12 Specifications Ripple ✽1 ESR ✽2 current tan d ✽3 (mΩ max.) (mAr.m.s.) 2390 23 0.12 4520 13 0.15 5440 12 0.18 740 200 0.15 1100 70 0.12 1400 60 0.12 1810 40 0.12 2560 35 0.12 4520 13 0.15 3700 25 0.12 5440 12 0.18 740 200 0.12 1100 70 0.12 1700 45 0.12 1810 40 0.12 2780 17 0.12 2560 35 0.12 3700 25 0.12 3700 25 0.12 3700 25 0.12 4210 15 0.15 5440 12 0.15 670 240 0.08 670 240 0.09 700 220 0.10 740 200 0.10 1100 70 0.12 1620 50 0.12 1700 45 0.12 2560 35 0.12 2560 35 0.12 3020 30 0.12 3700 25 0.12 3700 25 0.12 3950 17 0.15 5230 13 0.15 660 260 0.07 1020 120 0.10 1060 90 0.10 1620 50 0.10 1890 45 0.12 2120 40 0.12 2670 35 0.12 3020 30 0.12 3020 30 0.12 3640 20 0.15 4720 16 0.15 1020 120 0.10 1450 60 0.10 1450 60 0.10 1890 45 0.12 1890 45 0.12 2400 40 0.12 2400 40 0.12 3320 24 0.15 4320 20 0.15 LC ✽4 (µA) 110 340 750 66 78 136 120 264 448 544 960 69.3 148 103 126 151 277 277 416 592 592 775 23.5 34 50 75 165 94 112 240 300 300 540 660 660 840 26.4 120 176 125 179 262 320 480 576 576 792 100 88 108 132 188 224 272 400 600 Standard (Reel size : f380) Min. Packaging Q'ty Part number (pcs) 2R5SVP220M 1000 2R5SVP680M 400 2R5SVP1500M 400 4SVP33M 2000 4SVP39M 1500 4SVP68M 1500 4SVP150MX 1000 4SVP330M 1000 4SVP560M 400 4SVP680M 500 4SVP1200M 400 6SVP22M 2000 6SVP47M 1500 6SVP82M 1000 6SVP100M 1000 6SVP120MV 1000 6SVP220MX 1000 6SVP220M 500 6SVP330M 500 6SVP470MX 500 6SVP470M 400 6SVP820M 400 10SVP4R7M 2000 10SVP6R8M 2000 10SVP10M 2000 10SVP15M 2000 10SVP33M 1500 1000 10SVP47M 10SVP56M 1000 10SVP120M 1000 10SVP150MX 1000 10SVP150M 500 10SVP270M 500 10SVP330MX 500 10SVP330M 400 10SVP560M 400 16SVP3R3M 2000 16SVP15M 1500 16SVP22M 1500 16SVP39M 1000 16SVP56M 1000 16SVP82M 1000 16SVP100M 500 16SVP150M 500 16SVP180MX 500 16SVP180M 400 16SVP330M 400 20SVP10M 1500 20SVP22M 1000 20SVP27M 1000 20SVP33M 1000 20SVP47M 1000 20SVP56M 500 20SVP68M 500 20SVP100M 400 20SVP150M 400 ✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Reflow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency Coefficient 120 Hz < f < 1 kHz 0.05 1 kHz < f < 10 kHz 0.3 10 kHz < f < 100 kHz 0.7 100 kHz < f < 500 kHz 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Radial Lead Type Series : SXE Features ● Super ● RoHS high voltage (100 V.DC max.) compliance, Halogen free Specifications Size code Category temperature range Rated voltage range Rated capacitance range Capacitance tolerance Leakage current Dissipation factor (tan d) Endurance Damp heat (Steady State) E12 –55 °C to +105 °C 63 V.DC to 100 V.DC 15 µF to 33 µF ±20 % (120 Hz / + 20 °C) Please see the attached characteristics list Please see the attached characteristics list +105 °C, 5000 h, rated voltage applied Capacitance change Within ±20 % of the initial value tan d < 150 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Dimensions (not to scale) fd±0.05 fD±0.5 Polarity marking (−) Lot. No. + F Marking – Series L max. 15 min. 4 min. 19 min. Unit : mm R. Capacitance Size code R. Voltage E12 fD±0.5 8.0 L max. 12.0 F±0.5 3.5 fd±0.05 0.6 ✽ Externals of figure are the reference. Characteristics list Series SXE Rated Rated voltage capacitance (V.DC) (µF) 63 100 33 15 Case size (mm) fD L 8.0 8.0 12.0 12.0 Size code E12 Specifications Ripple ✽1 ESR ✽2 current tan d ✽3 (mΩ max.) (mAr.m.s.) 2950 25 0.12 2350 40 0.12 LC ✽4 (µA) 104 75 Part number 63SXE33M 100SXE15M ✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Flow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency Coefficient 120 Hz < f < 1 kHz 0.05 1 kHz < f < 10 kHz 0.3 10 kHz < f < 100 kHz 0.7 100 kHz < f < 500 kHz 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Radial Lead Type Series : SEPF Features ● High voltage (35 V.DC max.) ● Large capacitance (1000 μF max.) ● RoHS compliance, Halogen free Specifications Size code C55 C6 E7 E12 F13 Category temperature range –55 °C to +105 °C Rated voltage range 16 V.DC to 32 V.DC 16 V.DC to 35 V.DC Rated capacitance range 22 μF to 150 μF 22 μF to 180 μF 39 μF to 270 μF 82 μF to 560 μF 120 μF to 1000 μF Capacitance tolerance ±20 % (120 Hz / + 20 °C) Leakage current Please see the attached characteristics list Dissipation factor (tan d) Please see the attached characteristics list +105 °C, 5000 h, rated voltage applied Capacitance change Within ±20 % of the initial value Endurance tan d < 150 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value Damp heat (Steady State) tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Marking Dimensions (not to scale) Unit : mm fD±0.5 fd±0.05 Series R. Voltage + – L max. R. Capacitance Size code C55 C6 E7 E12 F13 F Polarity marking (−) Lot. No. 15 min. 4 min. 19 min. ✽ Externals of figure are the reference. fD±0.5 L max. F±0.5 fd±0.05 6.3 5.5 2.5 0.45 6.3 6.0 2.5 0.5 8.0 7.0 3.5 0.5 ✽ 8.0 12.0 3.5 0.6 10.0 13.0 5.0 0.6 ✽ 32SEPF68M : 0.6±0.05 Characteristics list Series Rated Rated voltage capacitance (V.DC) (μF) 16 20 SEPF 25 32 35 150 180 270 560 1000 120 180 390 560 56 82 180 330 22 68 22 39 82 120 Case size (mm) fD L Size code 6.3 6.3 8.0 8.0 10.0 6.3 8.0 8.0 10.0 6.3 8.0 8.0 10.0 6.3 8.0 6.3 8.0 8.0 10.0 5.5 6.0 7.0 12.0 13.0 6.0 7.0 12.0 13.0 6.0 7.0 12.0 13.0 5.5 7.0 6.0 7.0 12.0 13.0 C55 C6 E7 E12 F13 C6 E7 E12 F13 C6 E7 E12 F13 C55 E7 C6 E7 E12 F13 Specifications Ripple ✽1 ESR ✽2 current tan d ✽3 (mΩ max.) (mAr.m.s.) 2590 3300 3300 4950 5400 3200 3200 4950 5400 2800 3000 4650 5000 2400 3200 2600 2800 4000 4400 30 22 22 14 12 25 25 14 12 30 28 16 14 35 25 35 30 20 18 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.10 0.12 0.12 0.12 0.12 LC ✽4 (μA) Part number 480 576 864 1792 3200 480 720 1560 2240 280 410 900 1650 140 435 154 273 574 840 16SEPF150M 16SEPF180M 16SEPF270M 16SEPF560M 16SEPF1000M 20SEPF120M 20SEPF180M 20SEPF390M 20SEPF560M 25SEPF56M 25SEPF82M 25SEPF180M 25SEPF330M 32SEPF22M 32SEPF68M 35SEPF22M 35SEPF39M 35SEPF82M 35SEPF120M ✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Flow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency Coefficient 120 Hz < f < 1 kHz 0.05 1 kHz < f < 10 kHz 0.3 10 kHz < f < 100 kHz 0.7 100 kHz < f < 500 kHz 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Radial Lead Type Series : SEPC Features ● Super low ESR (5 mΩ to 24 mΩ) capacitance (2700 μF max.) ● RoHS compliance, Halogen free ● Large Specifications Size code B9 C55 C6 C9 E7 E9 E12 E13 F13 Category temperature range –55 °C to +105 °C Rated voltage range (V.DC) 2.5 6.3 2.5 to 16 6.3 to 16 2.5 to 16 16 2.5 to 6.3 2.5 to 16 Rated capacitance range (μF) 100 to 560 220 100 to 560 100 to 820 150 to 1000 180 to 1000 180 to 270 470 to 820 470 to 2700 Capacitance tolerance ±20 % (120 Hz / + 20 °C) Leakage current Please see the attached characteristics list Dissipation factor (tan d) Please see the attached characteristics list +105 °C, 5000 h, rated voltage applied Capacitance change Within ±20 % of the initial value Endurance tan d < 150 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value Damp heat (Steady State) tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Marking Dimensions (not to scale) E12, E13, F13 Size Unit : mm Polarity marking (−) Lot. No. – L 15 min. 4 min. 19 min. B9, C55, C6, C9, E7, E9 Size fd + R. Voltage fD R. Capacitance – L 15 min. 4 min. 19 min. B9, C55, C6, C9, E7, E9 size flat rubber is used. F Series + F fD fd Size code fD±0.5 L max. F±0.5 fd±0.05 B9 5.0 9.0 2.0 0.6 C55 6.3 5.5 2.5 0.45 C6 6.3 6.0 2.5 0.45 ✽1 C9 6.3 9.0 2.5 0.6 E7 8.0 7.0 3.5 0.6 ✽2 E9 8.0 9.0 3.5 0.6 E12 8.0 12.0 3.5 0.6 E13 8.0 13.0 3.5 0.6 F13 10.0 13.0 5.0 0.6 ✽1 2SEPC390M, 2SEPC560M : 0.5±0.05 ✽2 16SEPC150MD, 10SEPC270M : 0.45±0.05 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Characteristics list Series Rated Rated voltage capacitance (V.DC) (μF) 100 300 390 470 560 2.5 820 1000 2700 560 4.0 680 820 220 SEPC 470 6.3 10 560 680 1000 1500 270 100 150 16 180 220 270 470 Case size (mm) fD L 5.0 5.0 6.3 5.0 5.0 6.3 6.3 8.0 6.3 8.0 8.0 8.0 8.0 8.0 10.0 6.3 8.0 8.0 8.0 10.0 6.3 6.3 8.0 8.0 6.3 8.0 10.0 8.0 10.0 8.0 6.3 6.3 8.0 8.0 8.0 8.0 8.0 8.0 10.0 9.0 9.0 6.0 9.0 9.0 6.0 9.0 9.0 9.0 7.0 9.0 9.0 13.0 9.0 13.0 9.0 9.0 13.0 13.0 13.0 5.5 9.0 9.0 13.0 9.0 9.0 13.0 7.0 13.0 7.0 6.0 9.0 7.0 9.0 12.0 7.0 9.0 12.0 13.0 Size code B9 C6 B9 C6 C9 E9 C9 E7 E9 E13 E9 F13 C9 E9 E13 F13 C55 C9 E9 E13 C9 E9 E13 E7 F13 E7 C6 C9 E7 E9 E12 E7 E9 E12 F13 Specifications Ripple ✽1 ESR ✽2 current tan d ✽3 (mΩ max.) (mAr.m.s.) 4180 7 0.10 4180 7 0.10 3900 10 0.12 4180 7 0.10 4180 7 0.10 3900 10 0.12 5600 7 0.10 4700 8 0.10 5600 7 0.10 5300 8 0.10 6100 7 0.10 7200 5 0.10 6100 7 0.10 6100 7 0.10 5560 10 0.10 5600 7 0.10 6100 7 0.10 6100 7 0.10 6100 7 0.10 6640 7 0.10 2980 18 0.12 5600 7 0.10 5700 8 0.10 5700 8 0.10 5600 7 0.10 6100 7 0.10 6640 7 0.10 3530 18 0.10 5560 10 0.10 3220 22 0.12 2490 24 0.10 4680 10 0.10 3220 22 0.12 5000 10 0.10 4360 16 0.10 4150 13 0.10 5000 10 0.10 5000 11 0.10 6100 10 0.10 LC ✽4 (μA) Part number 500 500 500 500 500 500 500 280 500 500 500 500 500 500 1350 500 500 500 544 656 280 592 592 592 705 705 857 1260 1890 500 320 500 500 576 576 500 864 864 1504 2SEPC100MZ 2SEPC330MZ 2SEPC390M 2SEPC470MZ 2SEPC560MZ 2SEPC560M 2SEPC560MW 2SEPC560MX 2SEPC820MW 2SEPC820MD 2SEPC820MX 2SEPC820MY 2R5SEPC820M 2SEPC1000MX 2SEPC2700M 4SEPC560MW 4SEPC560MX 4SEPC560M 4SEPC680M 4SEPC820M 6SEPC220M 6SEPC470MW 6SEPC470MX 6SEPC470M 6SEPC560MW 6SEPC560MX 6SEPC680M 6SEPC1000MD 6SEPC1500M 10SEPC270MD 16SEPC100M 16SEPC100MW 16SEPC150MD 16SEPC180MX 16SEPC180M 16SEPC220MD 16SEPC270MX 16SEPC270M 16SEPC470M ✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Flow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency Coefficient 120 Hz < f < 1 kHz 0.05 1 kHz < f < 10 kHz 0.3 10 kHz < f < 100 kHz 0.7 100 kHz < f < 500 kHz 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Radial Lead Type Series : SEQP Features ● High voltage (32 V.DC max.) °C 1000 h ● RoHS compliance, Halogen free ● 125 Specifications Size code C6 E7 F8 E12 F13 Category temperature range –55 °C to +125 °C Rated voltage range 4 V.DC to 20 V.DC 4 V.DC to 32 V.DC 4 V.DC to 20 V.DC Rated capacitance range 22 µF to 150 µF 6.8 µF to 330 µF 15 µF to 680 µF 18 µF to 560 µF 150 µF to 1200 µF Capacitance tolerance ±20 % (120 Hz / + 20 °C) Leakage current Please see the attached characteristics list Dissipation factor (tan d) Please see the attached characteristics list +125 °C, 1000 h/+105 °C, 5000 h, rated voltage applied Capacitance change Within ±20 % of the initial value Endurance tan d < 200 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value Damp heat (Steady State) tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Dimensions (not to scale) fD fd Polarity marking (−) Lot. No. + F Marking – L 15 min. 4 min. 19 min. Series Unit : mm Size code R. Capacitance R. Voltage C6 E7 F8 E12 F13 fD±0.5 6.3 8.0 10.0 8.0 10.0 L max. 6.0 7.0 8.0 12.0 13.0 F±0.5 2.5 3.5 5.0 3.5 5.0 fd±0.05 0.45 0.45 0.50 0.60 0.60 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Characteristics list Rated Rated Series voltage capacitance (V.DC) (µF) 4.0 6.3 10 SEQP 16 20 32 150 330 560 680 1200 82 150 330 470 820 56 120 270 330 560 39 82 150 180 330 22 47 68 100 150 6.8 15 18 Case size (mm) fD L Size code 6.3 8.0 8.0 10.0 10.0 6.3 8.0 10.0 8.0 10.0 6.3 8.0 10.0 8.0 10.0 6.3 8.0 10.0 8.0 10.0 6.3 8.0 10.0 8.0 10.0 8.0 10.0 8.0 6.0 7.0 12.0 8.0 13.0 6.0 7.0 8.0 12.0 13.0 6.0 7.0 8.0 12.0 13.0 6.0 7.0 8.0 12.0 13.0 6.0 7.0 8.0 12.0 13.0 7.0 8.0 12.0 C6 E7 E12 F8 F13 C6 E7 F8 E12 F13 C6 E7 F8 E12 F13 C6 E7 F8 E12 F13 C6 E7 F8 E12 F13 E7 F8 E12 Specifications Ripple ✽1 Allowable ✽1 ESR ✽2 current ripple current tan d ✽3 (mΩ max.) (mAr.m.s.) (mAr.m.s.) 572 1810 40 0.12 810 2560 35 0.12 1430 4520 13 0.15 1170 3700 25 0.12 1721 5440 12 0.18 537 1700 45 0.12 810 2560 35 0.12 1170 3700 25 0.12 1332 4210 15 0.15 1721 5440 12 0.15 537 1700 45 0.12 810 2560 35 0.12 1170 3700 25 0.12 1250 3950 17 0.15 1655 5230 13 0.15 512 1620 50 0.10 670 2120 40 0.12 955 3020 30 0.12 1151 3640 20 0.15 1493 4720 16 0.15 458 1450 60 0.10 598 1890 45 0.12 759 2400 40 0.12 1050 3320 24 0.15 1367 4320 20 0.15 440 1400 100 0.10 560 1800 80 0.10 790 2500 50 0.12 LC ✽4 (µA) Part number 300 660 448 544 960 258 472 416 592 775 280 600 540 660 840 312 656 480 576 792 220 470 272 400 600 44 96 115 4SEQP150M 4SEQP330M 4SEQP560M 4SEQP680M 4SEQP1200M 6SEQP82M 6SEQP150M 6SEQP330M 6SEQP470M 6SEQP820M 10SEQP56M 10SEQP120M 10SEQP270M 10SEQP330M 10SEQP560M 16SEQP39M 16SEQP82M 16SEQP150M 16SEQP180M 16SEQP330M 20SEQP22M 20SEQP47M 20SEQP68M 20SEQP100M 20SEQP150M 32SEQP6R8M 32SEQP15M 32SEQP18M ✽1 Ripple current (100 kHz/ +105 °C < Tx < 125 °C), Allowable ripple current (100 kHz / Tx < 105 °C) ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Flow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency Coefficient 120 Hz < f < 1 kHz 0.05 1 kHz < f < 10 kHz 0.3 10 kHz < f < 100 kHz 0.7 100 kHz < f < 500 kHz 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Radial Lead Type Series : SEP Features ● Standard ● 105 °C 3000 h compliance, Halogen free ● RoHS Specifications Size code C6 E7 F8 E12 F13 Category temperature range –55 °C to +105 °C Rated voltage range 4 V.DC to 20 V.DC 2.5 V.DC to 20 V.DC Rated capacitance range 22 µF to 150 µF 33 µF to 330 µF 56 µF to 680 µF 100 µF to 680 µF 150 µF to 1500 µF Capacitance tolerance ±20 % (120 Hz / + 20 °C) Leakage current Please see the attached characteristics list Dissipation factor (tan d) Please see the attached characteristics list +105 °C, 3000 h, rated voltage applied (2.5 V.DC 2000 h applied) Capacitance change Within ±20 % of the initial value Endurance tan d < 150 % of the initial limit DC leakage current Within the initial limit +60 °C, 90 % to 95 %, 1000 h, No-applied voltage Capacitance change Within ±20 % of the initial value Damp heat (Steady State) tan d < 150 % of the initial limit DC leakage current Within the initial limit (after voltage processing) Dimensions (not to scale) fD fd Polarity marking (−) Lot. No. + F Marking – L 15 min. 4 min. 19 min. Series Unit : mm Size code R. Capacitance R. Voltage C6 E7 F8 E12 F13 fD±0.5 6.3 8.0 10.0 8.0 10.0 L max. 6.0 7.0 8.0 12.0 13.0 F±0.5 2.5 3.5 5.0 3.5 5.0 fd±0.05 0.45 0.45 0.50 0.60 0.60 ✽ Externals of figure are the reference. Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 Conductive Polymer Aluminum Solid Capacitors Characteristics list Series Rated Rated voltage capacitance (V.DC) (µF) 2.5 4.0 6.3 SEP 10 16 20 680 1500 100 150 220 330 470 560 680 1200 82 150 330 470 820 56 120 270 330 560 39 82 150 180 330 22 33 47 56 68 100 150 Case size (mm) fD L 8.0 10.0 6.3 6.3 8.0 8.0 10.0 8.0 10.0 10.0 6.3 8.0 10.0 8.0 10.0 6.3 8.0 10.0 8.0 10.0 6.3 8.0 10.0 8.0 10.0 6.3 8.0 8.0 10.0 10.0 10.0 8.0 10.0 12.0 13.0 6.0 6.0 7.0 7.0 8.0 12.0 8.0 13.0 6.0 7.0 8.0 12.0 13.0 6.0 7.0 8.0 12.0 13.0 6.0 7.0 8.0 12.0 13.0 6.0 7.0 7.0 8.0 8.0 8.0 12.0 13.0 Size code E12 F13 C6 E7 F8 E12 F8 F13 C6 E7 F8 E12 F13 C6 E7 F8 E12 F13 C6 E7 F8 E12 F13 C6 E7 F8 E12 F13 Specifications Ripple ✽1 ESR ✽2 current tan d ✽3 (mΩ max.) (mAr.m.s.) 4520 13 0.15 5440 12 0.18 1810 40 0.12 1810 40 0.12 2560 35 0.12 2560 35 0.12 3700 25 0.12 4520 13 0.15 3700 25 0.12 5440 12 0.18 1700 45 0.12 2560 35 0.12 3700 25 0.12 4210 15 0.15 5440 12 0.15 1700 45 0.12 2560 35 0.12 3700 25 0.12 3950 17 0.15 5230 13 0.15 1620 50 0.10 2120 40 0.12 3020 30 0.12 3640 20 0.15 4720 16 0.15 1450 60 0.10 1890 45 0.12 1890 45 0.12 2400 40 0.12 2400 40 0.12 2570 35 0.12 3320 24 0.15 4320 20 0.15 LC ✽4 (µA) Part number 340 750 200 300 440 660 376 448 544 960 258 472 416 592 775 280 600 540 660 840 312 656 480 576 792 220 330 470 224 272 400 400 600 2R5SEP680M 2R5SEP1500M 4SEP100M 4SEP150M 4SEP220M 4SEP330M 4SEP470M 4SEP560M 4SEP680M 4SEP1200M 6SEP82M 6SEP150M 6SEP330M 6SEP470M 6SEP820M 10SEP56M 10SEP120M 10SEP270M 10SEP330M 10SEP560M 16SEP39M 16SEP82M 16SEP150M 16SEP180M 16SEP330M 20SEP22M 20SEP33M 20SEP47M 20SEP56M 20SEP68M 20SEP100MX 20SEP100M 20SEP150M ✽1 Ripple current (100 kHz/ +105 °C ), ✽2 ESR (100 kHz to 300 kHz/+20 °C) ✽3 tan d (120 Hz/+20 °C) ✽4 After 2 minutes ◆ Please refer to each page in this catarog for “Flow conditions” and “Taping specifications”. Frequency correction factor for ripple current Frequency Coefficient 120 Hz < f < 1 kHz 0.05 1 kHz < f < 10 kHz 0.3 10 kHz < f < 100 kHz 0.7 100 kHz < f < 500 kHz 1 Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use. Should a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015 CAUTION AND WARNING 1. The electronic components contained in this catalog are designed and produced for use in home electric appliances, office eq uipment, information equipment, communications equipment, and other general purpose electronic devices. Before use of any of these components for equipment that requires a high degree of safety, such as medical instruments, aeros pace equipment, disaster-prevention equipment, security equipment, vehicles (automobile, train, vessel), please be sure to contact our sales representative. 2. When applying one of these components for equipment requiring a high degree of safety, no matter what sort of application it might be, be sure to install a protective circuit or redundancy arrangement to enhance the safety of your equipment. In addition, please carry out the safety test on your own responsibility. 3. When using our products, no matter what sort of equipment they might be used for, be sure to make a written agreement on thespecifications with us in advance. 4. Technical information contained in this catalog is intended to convey examples of typical performances and/or applications a nd is not intended to make any warranty with respect to the intellectual property rights or any other related rights of our company or any third parties nor grant any license under such rights. 5. In order to export products in this catalog, the exporter may be subject to the export license requirement under the Foreign Exchange and Foreign Trade Law of Japan. 6. No ozone-depleting substances (ODSs) under the Montreal Protocol are used in the manufacturing processes of Automotive & Ind ustrial Systems Company, Panasonic Corporation. Please contact Factory The information in this catalog is valid as of December 2015.