SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER CURRENT FEATURES GBJ Plastic package has UL Flammability Glassification 94V-0 Glass passivated chip junctions High case dielectric strength of 1500 VRMS High surge current capability Ideal for printed circuit boards High temperature soldering guaranteed 260℃/10 seconds, 0.375”(9.5mm) lead length 29.7-30.3 • • • 3.4-3.8 O .1 - 3 .4 2.5±0.2 2.0-2.4 Case: molded plastic body Terminal: Plated leads solderable per MIL-STD-750 Method 2026 Mounting position: Any (Note 3) Mounting Torque: 6 in – 1bs max. Weight: 0.15 ounce,4.0 gram 10.8-11.2 φ3 MECHANICAL DATA • • 4.4-4.8 O 19.7-20.3 3.0×45 2.7-3.1 3.8-4.2 17.0-18.0 • • • • • 10.0 Amperes 5.0 • 50 to 1000 Volts VOLTAGE RANGE GBJ10005 THRU GBJ1010 0.6-0.8 0.9-1.1 9.8-10.2 7.3-7.7 7.3-7.7 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% GBJ SYMBOLS GBJ VRRM VRMS VDC Maximum Reverse Peak Repetitive Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward At T C=100℃(Note Rectified Current, At TA=40℃(Note 1) 2) Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC Method) Rating for Fusing (t＜8.3ms) Maximum Instantaneous Forward Voltage drop Per bridge element 5.0A Maximum DC Reverse Current at rated DC blocking voltage per element TA=25℃ TA=125℃ Typical Junction Capacitance, per let (Measured at 1.0MHz and applied reverse voltage of 4.0V) Typical Thermal Resistance (Note 2 and 3) Operating Junction Temperature Range Storage Temperature Range GBJ GBJ GBJ GBJ GBJ 10005 1001 1002 1004 1006 1008 1010 50 35 50 100 70 100 200 140 200 400 280 400 10 5.0 600 420 600 800 560 800 1000 700 100 I(AV) UNIT Volts Volts Volts Amps IFSM 170 Amps I2 t 142 A2s VF 1.0 Volts IR 5.0 250 μA CJ 60 pF RJC TJ TSTG 2.2 (-55 to +150) (-55 to +150) ℃/W Notes: 1. Unit mounted on 150mm×150mm×1.6mm A1. Plate heatsink 2. Unit mounted on P.C.B. With 0.5×0.5”(1.2×1.2mm) copper pads and 0.375”(9.5mm) lead length 3. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum Heat transfer with #6 screw Web Site: www.hkmic.com ℃ ℃ SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER 50 to 1000Volts VOLTAGE RANGE GBJ10005 THRU GBJ1010 CURRENT 10.0 Amperes RATINGS AND CHARACTERISTIC CURVES GBJ10005 THRU GBJ1010 FIG. 1- DERATING CURVE OUTPUT RECTIFIED CURRENT FIG. 2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG PEAK FORWARD SURGE, CURRENT,(A) AVERAGE FORWARD OUTPUT CURRENT (A) 15 Heat-Sink Mounting. Tc 10 P.C.B. Mounting 5 200 100 1.0 Cycle 0 0 25 50 75 100 125 150 0 175 1 2 TEMPERATURE, ℃ FIG. 3- TYPICAL FORWORD CHARACTERISTICS PER LGE 8 10 20 40 60 100 100 TA=125℃ INSTANTANEOUS REVERSE CURRENT, (A) INSTANTANEOUS FORWARD CURRENT, (A ) 6 FIG. 4- TYPICAL REVERSE CHARACTERISTICS PER LEG 100 10 1 0.1 0.01 0.6 0.8 1.0 1.2 10 1 0.1 T A=25℃ 0.01 1.4 0 20 40 60 80 100 INSTANTANEOUS FORWARD VOLTAGE,(V) PERCENT OF RATED PEAK REVERSE VOLTAGE,(V ) FIG. 5- TYPICAL JUNCTION CAPACITANCE PER LEG FIG. 6- TYPICAL TRANSIENT THERMAL IMPEDANCE 100 TRANSIENT THERMAL IMPEDANCE (℃/W) 1000 JUNCTION CAPACITANCE, (pF) 4 NUMBER OF CYCLES AT 60 Hz 100 10 1 1 10 100 REVRESE VOLTAGE,( V) Web Site: www.hkmic.com 1 0.1 0.01 0.1 1 T, HEATING TIME (SEC.) 10