ABD0000C199

Plastic Film Capacitors
DC-Link Film Capacitor
Type : TYPE1
Features
● High
safety, Self-healing and Self-protecting function built in.
catastrophic failure upon natural end of life due to inbuilt fuse function.
● Open circuit failure mode by fuse function patterned electrode
● Can replace Electrolytic Capacitor
● Low ESR, High Ripple Current capability
● Low ESL
● RoHS directive compliant
● No
Recommended applications
● Any
automotive and/or other application requiring DC Linkage
✽ Verify the usage and fitting environments, and make sure to observe the rated performance specified in the
corresponding specifications.
Construction
● Dielectric
: Polypropylene
: Metallized dielectric with Segment pattern
● Plastic Case : PPS. equivalent to UL94 V-0
● Sealing
: Epoxy Resin equivalent to UL94 HB
● Terminal
: Copper with Tin plating
● Electrode
Explanation of part number
1
2
3
4
5
6
7
8
9
10
11
12
E
Z
T
V
K
C
T
Y
P
1
H
A
Specifications
Operating temperature
on the surface of the case
Capacitance
– 40 °C to +105 °C
including self heat generation
%
581 μF +10
−5 % at 1 kHz, 25 ºC
Rated voltage
450 V.DC
Maximum voltage
600 V.DC for 60 sec in life time
Rated ripple current
Continuous 80 Arms at 10 kHz
Current derating
Refer Fig.1
ESR
0.8 mΩ or less at 10KHz
ESL
Insulation Resistance
between Terminals and Case
Dimensions L × W × H (Typical data)
20 nH or less at 1MHz
1 GΩ or more
Measure after applying 500 +500 V.DC for 2 +20 seconds.
164 × 115 × 43.1 mm : Excluding terminals
Weight (Typical data)
980 g
Note:
1) Voltage includes ripple voltage
2) Derate the current when the maximum surface temperature exceeds 95 degC, as shown in Fig. 1.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Feb. 2016
Plastic Film Capacitors
Current Derating
100
90
95 °C
Ripple current (Arms @ 10k Hz)
80
70
60
50
40
30
20
10
0
−40
60
65
70
75
80
85
90
95
100
105
110
Temperature on the surface of the capacitor housing (°C)
Fig.1 Current derating curve
Dimensions
Unit : mm
N
f6
.9 +
8±0.3
149±0.4
80
STAMPING AREA
(34.5)
4-
33
STAMPING AREA
(7.5)
P
(40)
(6.5)
17±0.4
1
43.1±1
164±1
136±1
70±0.4
(51.5)
HATCHED AREA : LABEL
22.5
18±1
2-12
6
34.5±0.7
92.5
(20)
0
0 .3
f6
(22)
2-
63.5±0.4
.3
+0 0
.5
85.5±0.4
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Feb. 2016
Plastic Film Capacitors
Characteristics <Reference>
<Temperature characteristics (Typical curve)>
● Change
ΔC/C
10
ESR (mΩ) at 10 kHz
ΔC/C (%) at 1 kHz
10
● Equivalent
of capacitance
5
0
−5
series resistance
ESR
0.8
0.6
0.4
0.2
0.0
−10
−40
−20
0
60
20
40
Temperature (°C)
80
100
−40
−20
0
20
40
60
Temperature (°C)
80
100
<Frequency characteristics (Typical curve)>
● Equivalent
1.0
series resistance
ESR
ESR (mΩ)
0.8
0.6
0.4
0.2
0.0
10
15
20
Frequency (kHz)
25
<Lifetime Expectancy (Reference)>
✽ Expected life : 15,000 hours
✽ Failure in Time : 300 Fits
The above values are reference calculated under an pre-assumed average operating condition.
Design and specifications are each subject to change without notice. Ask factory for the current technical specifications before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
01 Feb. 2016