GLASS PASSIVATED SINGLE-OHASE BPIDGE RECTIFIER GBPC25005/W THRU GBPC2510/W VOLTAGE RANGE 50 to 1000 Volts CURRENT 25.0 Ampere GBPC35 GBPC35W FEATURES • • • • • • • Plastic package has UL flammability classification 94V-0 Integrally molded heatsink provides very low thermal resistance for maximum heat dissipation High forward surge capacity Glass passivated chip junction High isolation voltage from case to lugs High temperature soldering guaranteed: 260℃/10 seconds, A vailable in either lug package (GBPC25005) or wire lead package (GBPC25005W) 1.135(28.8) • • • 1.115(28.3) 0.72(17.1) .470(11.0) .632(16.1) .430(10.9) AC AC + 1.135(28.8) .672(17.1) .582(14.8) 1.115(28.3) .632(16.1) .542(13.8) + 1.135(28.8) .732(18.6) 1.115(28.3) .592(17.6) AC AC - .732(18.6) .732(18.6) .692(17.6) .692(17.6) 0.094(2.4)DIA. .042(1.07) .25(6.35) 0.034(.86) 0.030(.76) .038(.97) 1.25 (31.8) MIN. .840(21.3) MECHANICAL DATA • • 1.135(28.8) 1.115(28.3) 0.310(7.87) .740(18.8) .310(7.87) 0.290(7.36) .290(7.36) Case:Epoxy, Molded Plastic with integrally mounted heatsink Terminals: Plated 0.25”(6.35mm) lug or plated 0.040” (1.02mm) diameter lead Polarity: Polarity symbols market on case Mounting: Thru hole for #10 screw, 20 in-lbs Torque max. See Note 3 Weight: 0.53 ounce, 15.0 gram-GBPC35 and GBPC35-W .220(5.59) .220(5.59) .100(5.08) 0.200(5.08) HOLE FOR #10 SCREW METAL HEAT SINK HOLE FOR #10 SCREW METAL HEAT SINK Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% SYMBOLS GBPC GBPC Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current (SEE FIG.1) at TC=55℃ Peak Forward Surge Current 8.3mS single half sine wave superimposed on rated load (JEDEC method) Rating for Fusing (t＜8.3ms) Maximum Instantaneous Forward Voltage drop Per Bridge element 12.5A TA = 25℃ Maximum DC Reverse Current at rated DC blocking Voltage per element T = 125℃ A Isolation Voltage from case to lug or lead Typical Junction Capacitance per leg (NOTE 1) Typical Thermal Resistance per leg (NOTE 2) Operating Junction Temperature Storage Temperature Range VRRM VRMS VDC GBPC GBPC GBPC GBPC GBPC 25005/W 2501/W 2502/W 2504/W 2506/W 2508/W 2510/W 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 Volts Volts Volts I(AV) 25 Amps IFSM 300 Amps I2 t 375 A2s VF 1.1 Volts 5.0 500 2500 300 1.9 (-55 to +150) (-55 to +150) µA IR VISO Cj RΘJC TJ TSTG Notes: 1. 2. 3. UNIT Measured at 1.0MHz and applied reverse voltage of 4.0V Thermal resistance from junction to case per leg Bolt down on heat-sink with silicon thermal compound between bridge and mounting surface for maximum heat transfer efficiency with #10 screw. Web Site: www.hkmic.com nS pF ℃/W ℃ ℃ GLASS PASSIVATED SINGLE-OHASE BPIDGE RECTIFIER GBPC25005/W THRU GBPC2510/W VOLTAGE RANGE 50 to 1000 Volts CURRENT 25.0 Ampere FIG. 6 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG 100 10 INSTANTANEOUS REVERSE LEAKAGE CURRENT(μ A) INSTANTANEOUS FORWARD CURRENT (A) FIG. 5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG TJ =25℃ PULSE WIDTH=300 μs 1% DUTY CYCLE 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 T J =125 ℃ 100 T J =150℃ 10 1 50-400V 600-1000V TJ =25℃ 0.1 0.01 1.6 0 80 100 FIG .8 - TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG FIG. 7 - TYPICAL JUNCTION CAPACITANCE PER LEG 1000 600 TRANSIENT THERMAL IMPEDANCE, (℃ /W) TJ =25℃ f=1.0 MHz Vsig=50mVp-p JUNCTION CAPACITANCE, (pF) 60 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) INSTANTANEOUS FORWARD VOLTAGE, (V) 100 50 40 20 TJ =25℃ f=1.0 MHz Vsig=50mVp-p 100 10 1 1 100 10 REVERSE VOLTAGE,(V) Web Site: www.hkmic.com 0.01 0.1 1 t, HEATING TIME, sec. 10 100 GLASS PASSIVATED SINGLE-OHASE BPIDGE RECTIFIER GBPC25005/W THRU GBPC2510/W VOLTAGE RANGE 50 to 1000 Volts CURRENT 25.0 Ampere FIG. 6 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG 100 10 INSTANTANEOUS REVERSE LEAKAGE CURRENT(μ A) INSTANTANEOUS FORWARD CURRENT (A) FIG. 5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG TJ =25℃ PULSE WIDTH=300 μs 1% DUTY CYCLE 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 T J =125 ℃ 100 T J =150℃ 10 1 50-400V 600-1000V TJ =25℃ 0.1 0.01 1.6 0 80 100 FIG .8 - TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG FIG. 7 - TYPICAL JUNCTION CAPACITANCE PER LEG 1000 600 TRANSIENT THERMAL IMPEDANCE, (℃ /W) TJ =25℃ f=1.0 MHz Vsig=50mVp-p JUNCTION CAPACITANCE, (pF) 60 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) INSTANTANEOUS FORWARD VOLTAGE, (V) 100 50 40 20 TJ =25℃ f=1.0 MHz Vsig=50mVp-p 100 10 1 1 100 10 REVERSE VOLTAGE,(V) Web Site: www.hkmic.com 0.01 0.1 1 t, HEATING TIME, sec. 10 100