HIGH EFFICIENCY GLASS PASSIVATED RECTIFIER HERF1601C THRU HERF1607C VOLTAGE RANGE 50 to 1000 Volts CURRENT 16.0 Ampere FEATURES • • • • • • • • • ITO-220AB High speed switching Glass passivated chip junction Low power loss, high efficiency Low leakage High surge capacity High temperature soldering guaranteed 250℃/10 second, 0.16″(4.06mm) lead length Also available with common Anode, add an “A” suffix, i.e. HERF1601CA, add as a doubler, add a “D” suffix, i.e. HERF1601CD Also available in an isolated package, HER1601C Also available in the single chip version, HERF1601 MECHANICAL DATA • • • • • • Dimensions in inches and (millimeters) Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Lead: solderable per MIL-STD-202E method 208C Polarity: as Marked Mounting position: Any, 5 in-lbs Torque Max Weight: 0.08ounce, 2.24 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% HERF HERF SYMBOLS 1601C 1602C Maximum Repetitive Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 Maximum Average Forward Rectified Current At Tc=100℃ Peak Forward Surge Current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) HERF 1606C 600 420 600 HERF 1607C 800 560 800 UNIT Volts Volts Volts Amps IFSM 125 Amps Maximum DC Reverse Current at rated TA = 25℃ DC Blocking Voltage at TA = 125℃ IR Storage Temperature Range HERF 1605C 400 280 400 16.0 VF Operating Junction Temperature HERF 1604C 300 210 300 I(AV) Maximum Instantaneous Forward Voltage per at 8.0A Maximum Reverse Recovery Time Test conditions lF=0.5A, lR=1.0A, lRR=0.25A Typical Junction Capacitance (Measured at 1.0MHz and applied reverse voltage of 4.0V) Typical Thermal Resistance (NOTE 1) HERF 1603C 200 140 200 1.0 trr 1.3 1.5 1.7 10 500 70 Volts µA 100 nS CJ 40 pF RθJC TJ TSTG 2.5 (-55 to +150) (-55 to +150) ℃/W Notes: 1. Unit mounted on heatsink Web Site: www.hkmic.com ℃ ℃ HIGH EFFICIENCY GLASS PASSIVATED RECTIFIER HERF1601C THRU HERF1607C VOLTAGE RANGE 50 to 1000 Volts CURRENT 16.0 Ampere RATING AND CHRACTERISTIC CURVES HERF1601C THRU HERF1607C FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 20 16 12 8.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375″(9.5mm) Lead Length 4.0 150 CURRENT, (A) PEAK FORWARD SURGE 24 (A) AVERAGE FORWARD CURRENT, FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE 8.3ms Single Half Sine-Wave (JEDEC Method) T= Tjmax 100 50 1 Cycle 0 25 0 50 75 100 175 150 125 0 1 2 AMBIENT TEMPERATURE, (° C) 4 6 10 8 40 20 60 100 NUMBER OF CYCLES AT 60 Hz FIG.4-TYPICAL REVERSE CHARACTERISTICS PER LEG FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 0V 50 1.0 TJ =25° C Pulse Width=300us 1% Duty Cycle 0.1 0.4 0.8 1.6 1.2 INSTANTANEOUS FORWARD VOLTAGE,(V) 10 (μA) 80 0/ INSTANTANEOUS REVERSE CURRENT, /4 V 00 0/ 2 60 /10 30 0 10 00 V TJ=125° C (A) INSTANTANEOUS FORWARD CURRENT, 100 100 1.0 TJ =25° C 0.1 0.01 FIG.5-TYPICAL JUNCTION CAPACITANCE PER LEG 0 20 40 100 80 120 140 PERCENT OF RATED PEAK 100 JUNCTION CAPACITANCE,(pF) 60 REVERSE VOLTAGE,(%) F1G.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC Trr 50Ω 10Ω NONINDUCTIVE NONINDUCTIVE +0.5A (-) 10 (+) 25 Vdc (approx.) (-) T J =25° C f=1MHz Vsig=50mVp-p 1.0 1Ω NON INDUCTIVE PULSE GENERATIOR (NOTE 2) 0 -0.25A (+) OSCILLOSCOPE (NOTE 1) -1.0A 1 0.1 D.U.T. 10 REVERSE VOLTAGE,(V) 100 NOTES : 1.Rise Time=7ns mas. Input Impedance= 1 magohm. 22pF 2.Rise time=10ns max. Source Impedance= 50 ohms Web Site: www.hkmic.com 1cm SET TIME BASE FOR 50/100ns/cm