HIGH EFFICIENCY GLASS PASSIVATED RECTIFIER HER1601 THRU HER1607 VOLTAGE RANGE 50 to 1000 Volts CURRENT 16.0 Ampere FEATURES • • • • • • • • • TO-220AC High speed switching Glass passivated chip junction Low power loss for high efficiency Low leakage High surge capacity High temperature soldering guaranteed 250℃/10 second, 0.16″(4.06mm) lead length Also available in reverse polarity, add the “R” Suffix, i.e. HER1601R Also available in an isolated package, HERF1601 MECHANICAL DATA • • • • • • Case: Transfer molded plastic Epoxy: UL94V-0 rate flame retardant Lead: Solderable per MIL-STD-202E method 208C Polarity: as marked Mounting position: Any, 5 in-lbs Torque Max Weight: 0.08ounce, 2.24 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% HER HER SYMBOLS 1601 1602 Maximum Repetitive Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 Maximum Average Forward Rectified Current At Tc=100℃ Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage per at 16.0A Maximum DC Reverse Current at rated TA = 25℃ DC Blocking Voltage at T = 125℃ HER 1603 200 140 200 Typical Thermal Resistance (Note 1) Operating Junction Temperature Storage Temperature Range HER 1605 400 280 400 HER 1606 600 420 600 HER 1607 800 560 800 UNIT Volts Volts Volts I(AV) 16.0 Amps IFSM 225 Amps VF 1.0 1.3 IR trr 1.5 1.7 10 500 A Maximum Reverse Recovery Time Test conditions IF =0.5A, IR =1.0A, IRR =0.25A Typical Junction Capacitance (Measured at 1.0MHz and applied reverse voltage of 4.0V) HER 1604 300 210 300 70 Volts µA 100 nS CJ 40 pF RθJC TJ TSTG 2.5 (-55 to +150) (-55 to +150) ℃/W Notes: 1. Unit mounted on heatsink Web Site: www.hkmic.com ℃ ℃ HIGH EFFICIENCY GLASS PASSIVATED RECTIFIER HER1601 THRU HER1607 VOLTAGE RANGE 50 to 1000 Volts CURRENT 16.0 Ampere RATING AND CHRACTERISTIC CURVES HER1601 THRU HER1607 FIG.2-MAXIMUM NON-REPETITIVE PEAK FIG.1-TYPICAL FORWARD CURRENT DERATING CURVE FORWARD SURGE CURRENT 16 12 8.0 4.0 300 CURRENT, (A) Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375″(9.5mm) Lead Length 20 (A) PEAK FORWARD SURGE AVERAGE FORWARD CURRENT, 24 8.3ms Single Half Sine-Wave (JEDEC Method) T= T jmax 200 100 1 Cycle 0 0 50 25 100 75 125 150 175 0 2 1 AMBIENT TEMPERATURE, (° C) 4 6 8 10 40 20 60 100 NUMBER OF CYCLES AT 60 Hz FIG.4-TYPICAL REVERSE CHARACTERISTICS PER LEG FIG.3-TYPICAL INSTANTANEOUS 100 FORWARD CHARACTERISTICS PER LEG 30 0 /4 00 V V 0/ 2 00 80 0/ 0V / 10 60 50 (A) INSTANTANEOUS FORWARD CURRENT, 10 1.0 TJ =25° C Pulse Width=300us 1% Duty Cycle 0.1 0.4 0.8 10 (μA) INSTANTANEOUS REVERSE CURRENT, TJ=125° C 100 1.0 TJ =25° C 0.1 1.6 1.2 INSTANTANEOUS FORWARD VOLTAGE,(V) 0.01 0 20 FIG.5-TYPICAL JUNCTION CAPACITANCE PER LEG 40 60 100 80 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) JUNCTION CAPACITANCE,(pF) 100 F1G.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC Trr 50Ω 10Ω NONINDUCTIVE NONINDUCTIVE +0.5A (-) 10 (+) 25 Vdc (approx.) (-) T J =25° C f=1MHz Vsig=50mVp-p 1.0 1Ω NON INDUCTIVE PULSE GENERATIOR (NOTE 2) 0 -0.25A (+) OSCILLOSCOPE (NOTE 1) -1.0A 1 0.1 D.U.T. 10 REVERSE VOLTAGE,(V) 100 NOTES : 1.Rise Time=7ns mas. Input Impedance= 1 magohm. 22pF 2.Rise time=10ns max. Source Impedance= 50 ohms Web Site: www.hkmic.com 1cm SET TIME BASE FOR 50/100ns/cm