ET Vishay ESTA DC Filter Capacitors RIPPLE The sum of the peak ripple voltage and the DC voltage should not exceed the rated voltage. Refer to graph fig.1 for permissible peak-to-peak ripple voltage as a percentage of rated voltage for various frequencies. % RIPPLE 30 20 10 0 10 100 1000 10 000 Hz Fig. 1 POWER FACTOR TYPE ET These capacitors are manufactured using a mixed dielectric material that consists of polyester/polypropylene film and capacitor tissue. They are impregnated and filled with a mineral oil. The container is a Synthetic Resin Bonded Paper tube sealed at both ends with resin assuring hermetic sealing. The capacitors are terminated with M5 *12 mm studs or tinned copper wire. The power factor is variable, and is a function of temperature and frequency see fig. 2. Nominal value < 0.5 % at 20 °C at 20 °C 2% Power Factor vs. Temperature 1 kHz 1% Note • The impregnant used is a non toxic highly refined, purified and inhibited mineral oil. 50 Hz 0% - 20 40 65 80 Fig. 2 DIELECTRIC RESISTANCE APPLICATIONS The ET range is specifically designed for high voltage filters and can be successfully used in the following applications: (Parallel resistance) is indicated by the graph of insulance (MΩ x μF) vs temperature fig. 3. The insulance (MÉ1 x μF) is nominally 10 000 s at + 20 °C. (Measurements taken after 1 minute with an applied voltage of 500 V) MΩ x MF • By-pass • Coupling • Filter applications • X-ray power supplies 105 104 103 • Electrostatic air deaners 102 Insulance vs. Temperature Typical Values - 40 TEMPERATURE RANGE 0 40 80 Fig. 3 TEMPERATURE COEFFICIENT Capacitance will increase by 2 % per 100 °C temperature rise. CAPACITANCE RANGE LIFE EXPECTANCY ET type capacitors are designed for a life exceptancy of 5000 h at 65 °C. To achieve the same life expectancy at 85 °C derate to 60 % of rated voltage fig. 4. Hours Temperature range is - 55 °C to + 85 °C. Derating is required for operation at higher temperatures. 105 104 0.0005 μF to 2 μF. The tolerance is ± 10 %. Other tolerances are available on request. Nominal values measured at 1 kHz. 103 VOLTAGE RANGE 102 1000 VDC to 70 000 VDC Document Number: 13014 Revision: 11-Aug-10 0 50 100 150 °C Rated Voltage Fig. 4 For technical questions, contact: [email protected] www.vishay.com 1 ET DC Filter Capacitors Vishay ESTA TEST VOLTAGE TYPE DESCRIPTION Terminal/terminal (Vt/t) CAP. [μF] L [mm] D [mm] ET10-103 0.01 (1) 42 17 ET10-203 0.02 (1) 42 17 ET10-503 0.05 48 17 WEIGHT ET10-254 0.25 60 22 The approximate weight in grams may be calculated by multiplying the volume of the capacitor container by 1.2 x 10-3. ET10-504 0.5 70 30 ET10-205 2.0 110 35 17 For DC rating < 20 kV PART NUMBER Vt/t = 2.0 x rated voltage 60 s 1000 VDC WKG For DC rating > 20 kV Vt/t = 1.5 x rated voltage 60 s 1500 VDC WKG TERMINATIONS ET15-103 0.01 (1) 42 ET15-203 0.02 (1) 42 20 Add suffix W to part No. To indicate wire terminations. ET15-254 0.25 60 30 ET15-504 0.5 110 25 ET15-105 1.0 110 35 Capacitance tolerance of 20 % is standard with those marked. ET15-205 2.0 110 42 DIMENSIONS in millimeters ET20-103 0.01 (1) 48 17 ET20-503 0.05 60 17 CAPACITANCE L 12 D 12 2000 VDC WKG ET20-104 0.1 60 22 ET20-254 0.25 60 30 ET20-504 0.5 75 35 ET30-502 0.005 (1) 42 17 ET30-103 0.01 (1) 42 20 ET30-203 0.02 48 20 ET30-503 0.05 55 25 ET30-104 0.1 55 30 ET30-254 0.25 60 35 3000 VDC WKG 5 ET30-504 0.5 75 42 ET30-105 1.0 110 42 17 4000 VDC WKG ET40-102 0.001 (1) 42 ET40-502 0.005 (1) 42 17 ET40-503 0.05 60 22 ET40-103 0.01 42 20 ET40-104 0.1 60 30 ET40-504 0.5 95 42 5000 VDC WKG ET50-102 0.001 (1) 42 17 ET50-202 0.002 (1) 42 17 ET50-502 0.005 (1) 42 20 ET50-103 0.01 48 20 ET50-203 0.02 48 22 ET50-503 0.05 60 25 ET50-104 0.1 75 30 ET50-254 0.25 95 35 ET50-504 0.5 110 42 Notes (1) Capacitance tolerance of 20 % is standard • Non standard size containers can be supplied on request www.vishay.com 2 For technical questions, contact: [email protected] Document Number: 13014 Revision: 11-Aug-10 ET DC Filter Capacitors TYPE DESCRIPTION TYPE DESCRIPTION CAP. [μF] L [mm] D [mm] 6000 VDC WKG ET60-102 0.001 (1) 55 17 ET60-202 0.002 (1) 55 17 ET60-502 0.005 (1) 65 ET60-103 0.01 ET60-203 0.02 ET60-503 ET60-104 ET60-254 8000 VDC WKG ET80-502 PART NUMBER CAP. [μF] L [mm] D [mm] ET250-501 0.0005 (1) 145 17 ET250-102 0.001 (1) 145 20 17 ET250-502 0.005 175 30 65 20 ET250-103 0.010 175 35 80 20 ET250-503 0.05 300 42 0.05 100 25 30 000 VDC WKG 0.10 100 35 ET300-501 170 17 0.25 135 42 PART NUMBER 25 000 VDC WKG ET300-102 170 20 170 25 ET300-502 0.005 205 30 ET300-103 0.010 205 35 ET300-203 0.02 280 35 0.03 280 42 ET400-102 0.001 (1) 210 20 ET400-202 0.002 275 20 ET400-103 0.010 275 42 ET500-501 0.0005 (1) 275 22 ET500-102 0.001 (1) 275 22 ET500-202 0.002 340 22 ET500-502 0.005 340 35 ET500-103 0.010 340 42 65 20 0.01 80 20 ET80-503 0.05 105 35 ET80-104 0.10 105 42 ET300-303 ET80-254 10 000 VDC WKG ET100-102 0.25 170 42 40 000 VDC WKG 0.001 (1) 65 17 ET100-502 0.005 (1) 65 22 ET100-103 0.01 80 22 ET100-203 0.02 80 30 ET100-503 0.05 105 35 ET100-104 0.10 170 35 ET100-254 12 000 VDC WKG ET120-202 0.25 205 42 0.002 (1) 95 20 ET120-502 0.005 (1) 95 30 ET120-103 0.01 115 30 0.02 115 35 ET120-503 0.05 180 35 ET120-104 15 000 VDC WKG ET150-102 0.10 180 42 0.001 (1) 95 17 ET150-202 0.002 (1) 95 20 ET150-502 0.005 (1) 110 20 ET150-103 0.01 110 30 ET150-203 0.02 110 35 ET150-503 0.05 150 42 ET150-104 20 000 VDC WKG 0.10 245 42 ET200-102 0.001 (1) 115 22 ET200-502 0.005 (1) 145 25 ET200-103 0.01 145 30 ET200-203 0.02 195 30 ET200-503 0.05 245 42 ET200-104 0.10 320 42 0.001 (1) 0.002 ET80-103 ET120-203 0.0005 (1) ET300-202 0.005 (1) Document Number: 13014 Revision: 11-Aug-10 Vishay ESTA 50 000 VDC WKG 60 000 VDC WKG ET600-102 0.001 (1) 330 25 ET600-152 0.0015 330 30 Notes (1) Capacitance tolerance of 20 % is standard • Non standard size containers can be supplied on request For technical questions, contact: [email protected] www.vishay.com 3 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000