MKP385 Datasheet

MKP385
www.vishay.com
Vishay BCcomponents
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Radial Potted Type
FEATURES
• 5 mm to 52.5 mm lead pitch; 7.5 mm bent
back pitch
• Low contact resistance
• Low loss dielectric
• Small dimensions for high density packaging
• Supplied loose in box and taped on reel or
ammopack
• Material categorization: for definitions of
compliance please see www.vishay.com/doc?99912
APPLICATIONS
• Where steep pulses occur e.g. SMPS (switch mode power
supplies)
• Electronic lighting e.g. ballast
• Motor control circuits
• High frequency and pulse operations
• Deflection circuits in TV-sets (S-correction)
• Loudspeaker crossover networks, storage, filter, timing
and sample and hold circuits
QUICK REFERENCE DATA
Capacitance range (E24 series)
0.00047 μF to 82 μF
Capacitance tolerance
±5%
Climatic testing class according to IEC 60068-1
55/110/56
Rated DC temperature
85 °C
Rated AC temperature
85 °C
Maximum application temperature
110 °C
Maximum operating temperature for limited time
125 °C
Reference specifications
IEC 60384-17
Dielectric
Polypropylene film
Electrodes
Metallized
Construction
Mono and internal serial construction
Encapsulation
Flame retardant plastic case and epoxy resin
UL-class 94 V-0
Leads
Tinned wire
C-value; tolerance; rated voltage; manufacturer's type; code for dielectric material;
manufacturer location; manufacturer's logo; year and week
Marking
Note
• For more detailed data and test requirements, contact [email protected]
VOLTAGE RATINGS
Rated DC voltage
160
250
400
630
850
1000
1250
1600
2000
2500
Rated AC voltage
110
160
200
220
300
350
450
550
700 (1)
900 (2)
Rated peak to peak voltage
310
450
560
620
850
1000
1250
1600
2000
2500
Notes
(1) Rated AC voltage is 600 V
AC for pitch  37.5 mm
(2) Rated AC voltage is 800 V
AC for pitch  37.5 mm
Revision: 03-Jun-15
Document Number: 28174
1
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
COMPOSITION OF CATALOG NUMBER
Voltage (VDC)
016 = 160
Example
Multiplier (nF)
0.01
1
0.1
2
1
3
P1 (mm)
Pitch Code
025 = 250
5
B
C
040 = 400
7.5
147
470 pF
0.00047 μF
063 = 630
10
D
210
1 nF
0.001 μF
085 = 850
15
F
310
10 nF
0.01 μF
100 = 1000
22.5
I
410
100 nF
0.1 μF
125 = 1250
27.5
K
160 = 1600
37.5
P
200 = 2000
52.5
Y
510
1000 nF
1.0 μF
610
10 000 nF
10.0 μF
250 = 2500
Capacitance Code
(numerically)
Special Code for Terminal
10
4
2
2 pins
100
5
4
4 pins P2 = 10.2 mm
1000
6
5
4 pins P2 = 20.3 mm
(#)
Customized
1 2 3456
7
89
MKP385
1
47
10 11 12
2
5
0
13
14
15
16
17
18
J
F
P
2
T
0
Special
0 = Standard
Type
Tolerance
J
Other = Special
± 5%
A Special tolerance
It (mm)
Lead Length Code
Pitch (mm)
Packing Code
Packing Style
Remark
3.5 + 1.0/- 0.5
A
≤ 10
B/T
Bulk/loose (1)
Excluding bent back
3.5 ± 0.3
P
≥ 15
R
Tape and reel; (H: 16 mm; 500 mm)
For bent back only
5±1
M
All
Z
Tape and reel; (H: 16 mm; 356 mm)
For bent back only
25 ± 2
I
0: Space holder
All
H
W
Ammo (H: 16 mm)
Tape and reel (H: 18.5 mm; 500 mm)
For bent back only
Pitch 5 mm to 22.5 mm
G
Ammo (H: 18.5 mm)
Pitch ≤ 10 mm
Notes
• For detailed tape specifications refer to packaging information www.vishay.com/doc?28139
(1)
Packaging will be bulk for all capacitors with pitch  15 mm and such with long leads (> 5 mm).
Capacitors with short leads up to 5 mm and pitch > 15 mm will be in tray and asking code will be “T”.
Revision: 03-Jun-15
Document Number: 28174
2
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
ELECTRICAL DATA (For Detailed Ratings go to www.vishay.com/doc?28182)
URDC
(V)
CAP.
(μF)
0.011 min.
82 max.
0.010 min.
62 max.
0.0043 min.
27 max.
0.0015 min.
15 max.
0.001 min.
10 max.
0.00047 min.
6.8 max.
0.00047 min.
5.1 max.
0.00047 min.
2.7 max.
0.00047 min.
1.6 max.
0.00047 min.
0.68 max.
160
250
400
630
850
1000
1250
1600
2000
2500
DIMENSIONS in millimeters
l
w
h
lt
Ø dt
P
l
w
h h'
F'
(1)
F
H
Ø dt
10
15
I
w
Marking
h
Ø dt
CBB511
P1 ± 0.5
6 -2
P2 ± 0.5
Note
• | F-F' | < 0.3 mm
F = 7.5 mm + 0.6 mm / - 0.1 mm
Ø dt ± 10 % of standard diameter specified
Revision: 03-Jun-15
Document Number: 28174
3
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
MOUNTING
Normal Use
The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for
mounting on printed-circuit boards by means of automatic insertion machines.
For detailed tape specifications refer to “Packaging Information” www.vishay.com/doc?28139
Specific Method of Mounting to Withstand Vibration and Shock
In order to withstand vibration and shock tests, it must be ensured that the stand-off pips are in good contact with the
printed-circuit board:
• For original pitch = 15 mm the capacitors shall be mechanically fixed by the leads
• For larger pitches the capacitors shall be mounted in the same way and the body clamped
Space Requirements on Printed-Circuit Board
The maximum length and width of film capacitors is shown in the drawing:
For products with pitch  15 mm, w = l = 0.3 mm and h = 0.1 mm
For products with 15 mm < pitch  27.5 mm, w =l = 0.5 mm and h = 0.1
For products with pitch = 37.5 mm w = l = 0.7 mm and h = 0.5 mm
For products with pitch = 52.5 mm, w = l = 1 mm and h = 0.5 mm
Eccentricity as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product concerned.
wmax. = w + Δ
Eccentricity
Imax. = I + Δ
hmax. = h + Δ
Seating plane
SOLDERING CONDITIONS
For general soldering conditions and wave soldering provile we refer to the document “Soldering Conditions Vishay Film
Capacitors”: www.vishay.com/doc?28171
STORAGE TEMPERATURE
Storage temperature: Tstg = -25 °C to +35 °C with RH maximum 75 % without condensation.
RATINGS AND CHARACTERISTICS REFERENCE CONDITIONS
Unless otherwise specified, all electrical values apply to an ambient free temperature of 23 °C ± 1 °C, an atmospheric pressure
of 86 kPa to 106 kPa and a relative humidity of 50 % ± 2 %.
For reference testing, a conditioning period shall be applied over 96 h ± 4 h by heating the products in a circulating air oven at
the rated temperature and a relative humidity not exceeding 20 %.
Revision: 03-Jun-15
Document Number: 28174
4
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
CHARACTERISTICS
103
Impedance (Ω)
ΔC/C (%)
4
2
0
0.47 nF
102
101
-2
100
-4
10-1
100 nF
10 μF
82 μF
-6
10-2
-8
- 60
- 20
0
20
50
Tamb (°C)
100
10-3
104
130
106
107
f (Hz) 108
Impedance as a function of frequency (typical curve)
Capacitance as a function of ambient temperature (typical curve)
(1 kHz)
1.2
12
ΔT (°C)
factor
105
1.0
0.8
8
0.6
0.4
4
0.2
0.0
- 60
0
- 20
20
100 Tamb (°C)
60
0
Max. DC and AC voltage as function of temperature
30
60
90
Tamb (°C) 130
Maximum allowed component temperature rise (T)
as a function of ambient temperature (Tamb)
RC (s)
106
105
104
0
30
60
90
Tamb (°C) 120
Insulation resistance as a function of ambient temperature
(typical curve)
Revision: 03-Jun-15
Document Number: 28174
5
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
103
Tamb ≤ 85 °C, 160 VDC
85 °C < Tamb ≤ 110°C, 160 VDC
AC voltage
(V)
AC voltage
(V)
103
102
102
105
f (Hz) 106
101
102
Max. RMS voltage as function of frequency (160 V)
103
103
nF
22 F
0n
10
104
F
1μ
μF
2.2 F
μ
10
μF
47
103
nF
22 0 nF
10
F
1μ
μF
2.2
μF
10
μF
47
101
102
104
105
f (Hz) 106
Max. RMS voltage as function of frequency (160 V)
103
Tamb ≤ 85 °C, 250 VDC
AC voltage
(V)
102
102
103
104
105
106
f (Hz) 107
101
102
Max. RMS voltage as function of frequency (250 V)
103
nF
22 nF
0
10
101
102
F
1μ F
μ
2.2 μF
4.7 μF
22 7 μF
4
nF
22
F
0n
10
F
μF 1 μ
2.2
μF
4.7
μF
22 μF
47
AC voltage
(V)
85 °C < Tamb ≤ 110 °C, 250 VDC
104
105
106
f (Hz) 107
Max. RMS voltage as function of frequency (250 V)
103
103
AC voltage
(V)
102
102
101
102
103
104
105
106
f (Hz) 107
Max. RMS voltage as function of frequency (400 V)
Revision: 03-Jun-15
85 °C < Tamb ≤ 110 °C, 400 VDC
nF
10
F
0n
10 F
0n
47 F
1 μ μF
2.2 F
μ
10 2 μF
2
nF
10
F
0n
10 F
0n
47 F
F
1 μ .2 μ
2
μF
10 F
μ
22
AC voltage
(V)
Tamb ≤ 85 °C, 400 VDC
101
102
103
104
105
106
f (Hz) 107
Max. RMS voltage as function of frequency (400 V)
Document Number: 28174
6
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
103
AC voltage
(V)
Tamb ≤ 85 °C, 630 VDC
101
103
104
102
105
106
f (Hz) 107
101
102
Max. RMS voltage as function of frequency (630 V)
103
104
105
106
f (Hz) 107
Max. RMS voltage as function of frequency (630 V)
103
Tamb ≤ 85 °C, 850 VDC
104
105
nF
4.7
F
0n
10 nF
0
22 F
1 μ μF
4.7 μF
10
101
103
nF
4.7
F
0n
10 nF
0
22 F
1 μ μF
4.7 μF
10
102
85 °C < Tamb ≤ 110 °C, 850 VDC
AC voltage
(V)
AC voltage
(V)
103
nF
10 nF
47 nF
0
10 nF
0
47 F
μ
2.2.7 μF
4 μF
10
nF
10 nF
47 F
0n
10 nF
0
47
μF
2.2 μF
4.7 0 μF
1
102
85 °C < Tamb ≤ 110 °C, 630 VDC
AC voltage
(V)
103
102
106
f (Hz) 107
101
102
Max RMS voltage as function of frequency (850 V)
103
104
104
105
AC voltage
(V)
AC voltage
(V)
102
106
f (Hz) 107
Max. RMS voltage as function of frequency (1000 V)
Revision: 03-Jun-15
nF nF
4.7 10 F
n
47 0 nF
22 nF
0
47 μF
F
2.2 .7 μ
4
nF
4.7 nF
10 nF
47 nF
0
22 nF
0
47 F
μ
2.2 .7 μF
4
101
103
f (Hz) 107
85 °C < Tamb ≤ 110 °C, 1000 VDC
Tamb ≤ 85 °C, 1000 VDC
102
106
Max. RMS voltage as function of frequency (850 V)
103
103
105
101
102
103
104
105
106
f (Hz) 107
Max. RMS voltage as function of frequency (1000 V)
Document Number: 28174
7
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
103
Tamb ≤ 85 °C, 1250 VDC
101
103
104
105
μF
2.2 μF
10 F F
μ
47 00 n
F
1
0n
47 μF
2.2 μF
4.7
nF
2.2 F
n
10 nF
47 F
0n
10 nF
0
47 μF
2.2 μF
4.7
102
85 °C < Tamb ≤ 110 °C, 1250 VDC
AC voltage
(V)
AC voltage
(V)
103
102
106
f (Hz) 107
101
102
Max. RMS voltage as function of frequency (1250 V)
104
105
106
f (Hz) 107
Max. RMS voltage as function of frequency (1250 V)
103
AC voltage
(V)
Tamb ≤ 85 °C, 1600 VDC
101
103
104
105
nF
4.7
F
nF 47 n
22
F
0n
22 μF
1 2 μF
2.
nF
4.7 nF
22 nF F
47 0 n
22 F
1 μ μF
2.2
102
85 °C < Tamb ≤ 110 °C, 1600 VDC
AC voltage
(V)
103
103
102
106
f (Hz) 107
101
102
Max. RMS voltage as function of frequency (1600 V)
104
105
106
f (Hz) 107
Max. RMS voltage as function of frequency (1600 V)
103
102
AC voltage
(V)
85 °C < Tamb ≤ 110 °C, 2000 VDC
nF
2.2 nF
F
10 nF
0n
47 0 nF 47
22
F
1μ
nF
2.2 nF
10 nF F F
n n
47
0
0
22 47 F
1μ
AC voltage
(V)
103
103
102
Tamb ≤ 85 °C, 2000 VDC
101
103
104
105
106
f (Hz) 107
Max. RMS voltage as function of frequency (2000 V)
Revision: 03-Jun-15
101
102
103
104
105
106
f (Hz) 107
Max. RMS voltage as function of frequency (2000 V)
Document Number: 28174
8
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
103
103
102
101
103
104
AC voltage
(V)
102
105
f (Hz) 107
106
Max. RMS voltage as function of frequency (2500 V)
IRMS operational/IRMS max.
85 °C < Tamb ≤ 110 °C, 2500 VDC
nF
4.7
nF
47 nF
F
0
22 70 n
4
nF
4.7 nF
F
47
0n F
22 0 n
47
AC voltage
(V)
Tamb ≤ 85 °C, 2500 VDC
101
102
103
104
105
106
f (Hz) 107
Max. RMS voltage as function of frequency (2500 V)
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
50
60
70
80
90
100
110
Maximum ambient temperature (°C)
Maximum IRMS current in function of the ambient temperature
Revision: 03-Jun-15
Document Number: 28174
9
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
Dissipation factor (x 10-4)
www.vishay.com
Vishay BCcomponents
1000
100
20
11
10
9
8
7
6
5
4
3
15
14
13
12
19
18
2
17
16
1
10
1
100
1000
10 000
100 000
1 000 000
f (Hz)
Tangent of loss angle as a function of frequency (typical curve)
160 V:
C  0.018 μF, curve 1
0.018 < C  0.12 μF, curve 2
0.12 < C  0.16 μF, curve 5
0.16 < C  0.33 μF, curve 6
0.33 < C  0.47 μF, curve 7
0.47 < C  0.91 μF, curve 10
0.91 < C  1.1 μF, curve 11
1.1 < C  1.6 μF, curve 12
1.6 < C  2.4 μF, curve 13
2.4 < C  3 μF, curve 14
3 < C  5.6 μF, curve 15
5.6 < C  43 μF, curve 18
43 < C  82 μF, curve 20
250 V:
C  0.043 μF, curve 2
0.043 < C  0.091 μF, curve 3
0.091 < C  0.11 μF, curve 5
0.11 < C  0.43 μF, curve 6
0.33 < C  0.47 μF, curve 7
0.43 < C  0.91 μF, curve 10
0.91 < C  3.3 μF, curve 12
3.3 < C  5.6 μF, curve 13
5.6 < C  33 μF, curve 18
33 < C  62 μF, curve 20
400 V:
C  0.010 μF, curve 1
0.010 < C  0.036 μF, curve 2
0.036 < C  0.043 μF, curve 3
0.043 < C  0.18 μF, curve 4
0.18 < C  0.43 μF, curve 8
0.43 < C  0.75 μF, curve 10
0.75 < C  3.0 μF, curve 11
3.3 < C  15 μF, curve 17
15 < C  27 μF, curve 19
630 V:
C  0.018 μF, curve 1
0.018 < C  0.024 μF, curve 2
0.024 < C  0.043 μF, curve 3
0.043 < C  0.11 μF, curve 4
0.11 < C  0.24 μF, curve 7
0.24 < C  2.4 μF, curve 9
2.4 < C  8.2 μF, curve 16
8.2 < C  15 μF, curve 19
850 V:
C  0.0091 μF, curve 1
0.0091 < C  0.051 μF, curve 2
0.051 < C  0.12 μF, curve 3
0.12 < C  0.68 μF, curve 4
0.68 < C  1.3 μF, curve 6
1000 V:
C  0.015 μF, curve 1
0.015 < C  0.056 μF, curve 2
0.056 < C 0.10 μF, curve 3
0.1 < C  0.91 μF, curve 4
1250 V:
C  0.033 μF, curve 1
0.033 < C 0.091 μF, curve 2
0.091 < C  0.68 μF, curve 3
1600 V:
C  0.0091 μF, curve 1
0.0091 < C  0.27 μF, curve 2
0.27 < C  0.36 μF, curve 3
0.36 < C  1 μF, curve 5
2000 V:
C  0.018 μF, curve1
0.018 < C  0.22 μF, curve 2
0.22 < C  1 μF, curve 4
2500 V:
C  0.082 μF, curve1
0.082 < C  0.39 μF, curve 2
0.39 < C  0.68 μF, curve 4
Revision: 03-Jun-15
Document Number: 28174
10
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
HEAT CONDUCTIVITY (G) AS A FUNCTION OF (ORIGINAL) PITCH AND CAPACITOR BODY
THICKNESS IN mW/°C
Wmax
(mm)
3
3.5
4
4.5
5
6
7
8.5
9
10
11
12
13
14.5
15
18
18.5
21
21.5
24
25
30
35
HEAT CONDUCTIVITY (mW/°C)
PITCH
5 mm
3
4
5.5
-
PITCH
7.5 mm
4
5
6
7
-
PITCH
10 mm
6.5
7.5
9
-
PITCH
15 mm
10
11
12
16
18
-
PITCH
22.5 mm
19
21
25
28
34
-
PITCH
27.5 mm
31
36
42
48
57
68
-
PITCH
37.5 mm
89
102
116
134
-
PITCH
52.5 mm
152
181
197
POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function
of the free air ambient temperature.
The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical information film
capacitors with the typical tgd of the curves.”.
The component temperature rise (T) can be measured (see section “Measuring the component temperature” for more details)
or calculated by T = P/G:
• T = component temperature rise (°C)
• P = power dissipation of the component (mW)
• G = heat conductivity of the component (mW/°C)
MEASURING THE COMPONENT TEMPERATURE
A thermocouple must be attached to the capacitor body as in:
Thermocouple
CBA758
The temperature is measured in unloaded (Tamb) and maximum loaded condition (TC).
The temperature rise is given by T = TC - Tamb.
To avoid radiation or convection, the capacitor should be tested in a wind-free box.
Revision: 03-Jun-15
Document Number: 28174
11
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
APPLICATION NOTE AND LIMITING CONDITIONS
For capacitors connected in parallel, normally the proof voltage and possibly the rated voltage must be reduced. For information
depending of the capacitance value and the number of parallel connections contact: [email protected]
These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as
described hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic
interference suppression capacitors conforming the standards must be used.
To select the capacitor for a certain application, the following conditions must be checked:
1. The peak voltage (Up) shall not be greater than the rated DC voltage (URDC)
2. The peak-to-peak voltage (Up-p) shall not be greater thanthe maximum (Up-p) to avoid the ionization inception level
3. The voltage peak slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by URDC and
divided by the applied voltage.
For all other pulses following equation must be fulfilled:

T

dU 2
dU

2    --------  dt  U RDC   --------
 dt 
 dt  rated

0
T is the pulse duration
4. The maximum component surface temperature rise must be lower than the limits (see graph “Max. allowed component
temperature rise”).
5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values
mentioned in the table: “Heat Conductivity”
6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected
with an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes
and surge voltages from the mains included).
VOLTAGE CONDITIONS FOR 6 ABOVE
ALLOWED VOLTAGES
Maximum continuous RMS voltage
Maximum temporary RMS-over voltage (< 24 h)
Maximum peak voltage (Vo-p) (< 2 s)
Tamb ≤ 85 °C
URAC
1.25 x URAC
1.6 x URDC
85 °C < Tamb ≤ 110 °C
0.7 x URAC
0.875 x URAC
1.1 x URDC
110 °C < Tamb ≤ 125 °C
0.5 x URAC
0.625 x URAC
0.8 x URDC
EXAMPLE
C = 4n7 - 1600 V used for the voltage signal shown in next drawing.
Up-p = 1000 V; Up = 900 V; T1 = 12 μs; T2 = 64 μs; T3 = 4 μs
The ambient temperature is 80 °C. In case of failure, the oscillation is blocked.
Checking the conditions:
1. The peak voltage Up = 900 V is lower than 1600 VDC
2. The peak-to-peak voltage 1000 V is lower than 22 x 550 VAC = 1600 Up-p
3. The voltage pulse slope (dU/dt) = 1000 V/4 μs = 250 V/μs
This is lower than 4000 V/μs (see specific reference data for each version)
4. The dissipated power is 35 mW as calculated with fourier terms and typical tgd.
The temperature rise for Wmax. = 6 mm and pitch = 15 mm will be 35 mW/9 mW/°C = 3.9 °C
This is lower than 10 °C temperature rise at 80 °C, according graph.
5. Oscillation is blocked
6. Not applicable
VOLTAGE SIGNAL
Voltage
Up
Up-p
Time
T3
T1
T2
Revision: 03-Jun-15
Document Number: 28174
12
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
INSPECTION REQUIREMENTS
General Notes
Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-17 and
Specific Reference Data”.
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C1A PART OF SAMPLE OF
SUB-GROUP C1
4.1
Dimensions (detail)
As specified in Chapters “General data” of
this specification
4.3.1 Initial measurements
Capacitance
Tangent of loss angle:
C ≤ 1 μF at 100 kHz
1 μF < C ≤ 10 μF at 10 kHz
C > 10 μF at 1 kHz
4.3
Robustness of terminations
Tensile: load 10 N; 10 s
Bending: load 5 N; 4 x 90°
4.4
Resistance to soldering heat
Method: 1 A
Solder bath: 280 °C ± 5 °C
Duration: 10 s
No visible damage
4.14 Component solvent resistance
Isopropylalcohol at room temperature
Method: 2
Immersion time: 5 min ± 0.5 min
Recovery time:
min. 1 h, max. 2 h
4.4.2 Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
lC/Cl  1 % of the value measured initially.
Tangent of loss angle
Increase of tan :
 0.0005 for: C  100 nF at 100 kHz
 0.0010 for: 100 nF < C  470 nF at 100 kHz
 0.0015 for: 470 nF < C  1 μF at 100 kHz
 0.0015 for: 1 μF < C  10 μF at 10 kHz
 0.0015 for: C > 10 μF at 1 kHz
Compared to values measured in 4.3.1
4.6.1 Initial measurements
Capacitance
Tangent of loss angle:
C  1 μF at 100 kHz
1 μF < C  10 μF at 10 kHz
C >10 μF at 1 kHz
4.15 Solvent resistance of the marking
Isopropylalcohol at room temperature
Method: 1
Rubbing material: cotton wool
Immersion time: 5 min ± 0.5 min
4.6
 A = -55 °C
 B = +110 °C
5 cycles
Duration t = 30 min
Rapid change of temperature
Revision: 03-Jun-15
No visible damage
Legible marking
Document Number: 28174
13
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
SUB-GROUP C1A PART OF SAMPLE OF
SUB-GROUP C1
4.7.
Vibration
CONDITIONS
Visual examination
Mounting: see section “Mounting” for
more information
Procedure B4
Frequency range: 10 Hz to 55 Hz.
Amplitude: 0.75 mm or
Acceleration 98 m/s2
(whichever is less severe)
Total duration 6 h.
PERFORMANCE REQUIREMENTS
No visible damage
4.7.2
Final inspection
Visual examination
4.9
Shock
Mounting: see section “Mounting” for
more information
Pulse shape: half sine
Acceleration: 490 m/s2
Duration of pulse: 11 ms
4.9.3
Final measurements
Visual examination
No visible damage
Capacitance
lC/Cl ≤ 2 % of the value measured in 4.6.1.
Tangent of loss angle
Increase of tan :
 0.0005 for: C  100 nF at 100 kHz 
 0.0010 for: 100 nF < C  470 nF at 100 kHz
 0.0015 for: 470 nF < C  1 μF at 100 kHz
 0.0015 for: 1 μF < C  10 μF at 10 kHz
 0.0015 for: C > 10 μF at 1 kHz
Compared to values measured in 4.6.1
Insulation resistance
As specified in section “Insulation
Resistance” of this specification.
SUB-GROUP C1
COMBINED SAMPLE OF SPECIMENS OF
SUB-GROUPS C1A AND C1B
4.10
Climatic sequence
4.10.2
Dry heat
4.10.3
Damp heat cyclic
Test Db, first cycle
4.10.4
Cold
4.10.6
Damp heat cyclic
Test Db remaining cycles
4.10.6.2 Final measurements
Revision: 03-Jun-15
Temperature +110 °C
Duration: 16 h
Temperature: -55 °C
Duration: 2 h
Voltage proof = URDC for 1 min within
15 min after removal from test chamber
No breakdown or flashover
Visual examination
No visible damage
Legible marking
Capacitance
lC/Cl  2 % of the value measured in 4.4.2
or 4.9.3
Tangent of loss angle
Increase of tan :
 0.0005 for: C  100 nF at 100 kHz
 0.0010 for: 100 nF < C  470 nF at 100 kHz
 0.0015 for: 470 nF < C  1 μF at 100 kHz
 0.0015 for: 1 μF <C  10 μF at 10 kHz
 0.0015 for: C >10 μF at 1 kHz
Compared to values measured in 4.3.1
or 4.6.1
Insulation resistance
 50 % of values specified in section
“Insulation Resistance” of this specification.
Document Number: 28174
14
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C2
4.11
Damp heat steady state
56 days; 40 °C; 90 % to 95 % RH
no load
4.11.1
Initial measurements
Capacitance
Tangent of loss angle at 1 kHz
4.11.3
Final measurements
Voltage proof = URDC for 1 min within
15 min after removal from test chamber
No breakdown or flashover
Visual examination
No visible damage
Legible marking
Capacitance
lC/Cl  2 % of the value measured in
4.11.1.
Tangent of loss angle
Increase of tan 
 0.0005 for: C  100 nF at 100 kHz
 0.0010 for: 100 nF < C 470 nF at 100 kHz
 0.0015 for: 470 nF < C  1 μF at 100 kHz
 0.0015 for: 1 μF < C  10 μF at 10 kHz
 0.0015 for: C >10 μF at 1 kHz
Compared to values measured in 4.11.1.
Insulation resistance
 50 % of values specified in section
“Insulation resistance” of this specification
SUB-GROUP C3A
4.12.1
Endurance
Duration: 2000 h
Temperature: 85 °C
Voltage: 1.25 x URAC VRMS, 50 Hz or
Duration: 2000 h
Temperature: 110 °C
Voltage: 0.875 x URAC VRMS, 50 Hz
4.12.1.1 Initial measurements
Capacitance
Tangent of loss angle
C  1 μF at 100 kHz
1 μF < C  10 μF at 10 kHz
C > 10 μF at 1 kHz
4.12.1.3 Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
lC/Cl  5 % for C > 10 nF
lC/Cl  8 % for C  10 nF
Compared to values measured in 4.12.1.1
Tangent of loss angle
Increase of tan :
 0.0005 for: C  100 nF at 100 kHz
 0.0010 for: 100 nF < C  470 nF at 100 kHz
 0.0015 for: 470 nF < C  1 μF at 100 kHz
 0.0015 for 1 μF < C  10 μF at 10 kHz
 0.0015 for: C > 10 μF at 1 kHz
Compared to values measured in 4.12.1.1
Insulation resistance
 50 % of values specified in section
“Insulation resistance” of this specification.
Revision: 03-Jun-15
Document Number: 28174
15
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C3B
4.12.2
Endurance test at 50 Hz
alternating voltage
Duration: 500 h
Voltage: 1.25 x URDC 110 °C
4.12.2.1 Initial measurements
0.625 x URAC at 125 °C
Capacitance
Tangent of loss angle:
C  1 μF at 100 kHz
1 μF < C  10 μF at 10 kHz
C > 10 μF at 1 kHz
4.12.2.3 Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
lC/Cl ≤ 10 % + 100 pF compared to values
measured in 4.12.2.1
Tangent of loss angle
Increase of tan :
 0.0005 for: C  100 nF at 100 kHz
 0.0010 for: 100 nF < C  470 nF at 100 kHz
 0.0015 for: 470 nF < C  1 μF at 100 kHz
 0.0015 for: 1 μF < C  10 μF at 10 kHz
 0.0015 for: C >10 μF at 1 kHz
Compared to values measured in 4.12.2.1
Insulation resistance
 50 % of values specified in section
“Insulation Resistance” of this
specification.
Capacitance
Capacitance at -55 °C
Capacitance at 20 °C
Capacitance at +125 °C
For -55 °C to +20 °C:
+1 %  lC/Cl  3.75 % or
for 20 °C to 105 °C:
-7.5 %  lC/Cl  0 %
Capacitance
As specified in section “Capacitance” of
this specification
Insulation resistance
As specified in section “Insulation
Resistance” of this specification
SUB-GROUP C4
4.2.6
Temperature characteristics
Initial measurements
Intermediate measurements
Final measurements
4.13
Charge and discharge
10 000 cycles
Charged to URDC discharge resistance:
U RDC
R = --------------------------------------2.5 x C (dU/dt)

4.13.1
Initial measurements
4.13.3
Final measurements
Revision: 03-Jun-15

Capacitance
Tangent of loss angle:
C ≤ 1 μF at 100 kHz
1 μF < C  1 μF at 10 kHz
C  10 μF at 1 kHz
Capacitance
lC/Cl  1 % compared to values measured
in 4.13.1.
Tangent of loss angle
Increase of tan :
 0.0005 for: C  100 nF or
 0.001 for: 100 nF < C  470 nF or
 0.0015 for: C > 470 nF
Compared to values measured in 4.13.1
Insulation resistance
 50 % of values specified in section
“Insulation Resistance” of this
specification.
Document Number: 28174
16
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MKP385
www.vishay.com
Vishay BCcomponents
GROUP C INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP ADD1
A.1
Ignition of lamp test
Only for 1600 V and 2000 V series
(Cap. value < 33 nF)
Capacitance
A.1.1 Initial measurements
Tangent of loss angle at 100 kHz
Temperature: 85 °C
A.1.2 Ignition of lamp test
10 000 cycles: 1 s ON 29 s OFF:
Frequency: 60 kHz
Voltage:
1600 V type: 2800 Vpp2000 V type: 3000
Vpp
A.1.3 Final measurements
Visual examination
Capacitance
Revision: 03-Jun-15
No visible damage
lC/Cl ≤ 5 % of the value measured in A.1.1
Tangent of loss angle
Increase of tan :
 0.0005 for: C  100 nF at 100 kHz
 0.0010 for: 100 nF < C  470 nF at 100 kHz
 0.0015 for: 470 nF < C  1 μF at 100 kHz
 0.0015 for: 1 μF < C  10 μF at 10 kHz
 0.0015 for: C >10 μF at 1 kHz
Compared to values measured in A.1.1
Insulation resistance
 50 % of values specified in section
“Insulation Resistance” of this specification
Document Number: 28174
17
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000