INDEX GENERALS AND EXTRAS Title of Page Index-Generals and Extras General Price Data Special Tolerances Special Tolerances, Continued Marking and Tape Charges Cores, Separators, Interleaving and Oiling Packing Charges Page Number 1 2 3 4 5 6 7 Date of Page 1990 June 1 2007 August 9 1988 August 22 1988 August 22 1989 January 10 1990 April 18 2005 December 21 ♦indicates change from or addition to previous issue Tables do not indicate availability. Refer to Product Data for thickness, width, length and temper limitations. Republished Date 2007 November 20 2007 August 9 2007 November 20 2007 November 20 2007 November 20 2007 November 20 2007 November 20 A L C O A 1988 August 22 P R I C E 3 D A T A Section S&P 101 North American Rolled Products Reprinted 2007 November 20 NO CHANGE Alcoa Inc. SPECIAL TOLERANCES (INQUIRY is required on all tolerances CLOSER THAN COMMERCIAL) TOLERANCES – THICKNESS – Price Per Pound PLATE FLAT SHEET COILED SHEET PLATE CIRCLES Thickness Tolerance Closer 1/2 2/3 Com1/2 ComCommercial mercial mercial Alloys Thickness Range, Inches Width Range, Inches All Heat Treatable Alloys 6.0000-.1610 .1609-.0060 Thru 90 $.05 $.07 $.07 $.09 $.08 $.11 All Other Alloys 6.0000-.1610 .1609-.0060 Thru 90 $.04 $.05 $.05 $.07 $.07 $.09 The higher extra applies for tolerances between the fractional tolerances shown. TOLERANCES – WIDTH – Extra Per Pound PLATE FLAT SHEET Width Tolerances Thickness Range, Inches Width Range, Inches 2/3 Commercial 1/2 Commercial 1/3 Commercial 1/4 Commercial or closer 6.0000-.0060 12-144 $0.01 $0.02 $0.03 $0.04 COILED SHEET Width Tolerance, Plus and Minus Inches Thickness Range, Inches Width Range, Inches 0.032 0.016 0.01 0.007 0.005 0.003 .1260-.0060 1.00-12.00 12.01-60.00 ___ $.01 $.01 $.01 $.01 $.02 $.02 $.04 $.03 $.06 $.04 --- The higher extra applies for tolearnces between the fractional tolerances shown. TOLERANCES – LENGTH – Extra Per Pound PLATE FLAT SHEET Length Tolerances Thickness 2/3 Commercial 1/2 Commercial 1/3 Commercial 1/4 Commercial 1/5 Commercial 6.0000-.0060 $0.01 $0.02 $0.03 $0.04 $0.06 The higher extra applies for tolerances between the fractional tolerances shown. ♦indicates change from or addition to previous issue Tables do not indicate availability. Refer to Product Data for thickness, width, length and temper limitations. A L C O A 1988 August 22 Reprinted 2007 November 20 NO CHANGE P R I C E 4 D A T A North American Rolled Products Section S&P 101 Alcoa Inc. SPECIAL TOLERANCES (INQUIRY is required on all tolerances CLOSER THAN COMMERCIAL) TOLERANCES – RESQUARED – Extra Per Pound FLAT SHEET Tolerances Thickness Range, Inches .2499-.0230 Width Range, Inches Length Range, Inches Squareness Width Length Extra 25-100 60-180 1/2 Commercial 1/2 Commercial 1/2 Commercial $0.05 Not applicable to O temper. TOLERANCE – FLATNESS – Extra Per Pound PLATE-LONGITUDINAL FLATNESS Thickness, In. Tempers H 3.0000.2500 T351, T451 T651, T851 Tolerance-Inches Allowable Extra 1/4 in. in any 6 ft. or less (Standard) 3/16 in. in any 6 ft. (Special) NO CHARGE $.01 3/16 in. in any 6 ft. or less (Standard) 1/8 in. in any 6 ft. (Special) NO CHARGE $.01 TOLERANCE – TRANSVERSE FLATNESS – Extra Per Pound PLATE H Temper T351, T451, T651 and T851 Tempers Tolerances-Inchesº Allowable Deviation from Flat Tolerances-Inchesº Allowable Deviation from Flat Widths Widths Widths Widths over 4 ft. over 2 ft. Widths over 4 ft. over 2 ft. Widths 2 ft. 2 ft. thru thru thru thru 6 ft.³ 4 ft. and less¹ ² Extra 6 ft.³ 4 ft. and less¹ ² Extra 3/16 1/8 0.075 $0.01 1/8 1/8 0.065 $0.01 3.0000-1.5001 1/4 3/16 0.075 $0.01 3/16 1/8 0.065 $0.01 1.5000-.6250 .6249-.2500 3/8 1/4 0.09 $0.01 1/4 3/16 0.08 $0.01 º Measured with plate resting on a flat surface concave side upward, using a straight edge and a feeler gauge, dial gauge or scale. Thickness Range, Inches ¹ Short-cycle flatness is the flatness over any 2-foot span in any direction. ² Measured with plate resting on a flat surface, and by use of a frame with rollers mounted on 2-foot centers and a depth gauge in the center. ³ Widths over 6 feet, these tolerances apply for any 6 foot increment of total width. LATERAL BOW - Coiled Sheet INQUIRY CAMBER - Plate & Flat Sheet INQUIRY ♦indicates change from or addition to previous issue Tables do not indicate availability. Refer to Product Data for thickness, width, length and temper limitations. A L C O A 2007 November 20 Supersedes Previous Page Dated 1989 January 10 P R I C E 5 D A T A North American Rolled Products Section S&P 101 Alcoa Inc. STANDARD IDENTIFICATION MARKINGS Extra Per Pound ♦ (WHEN MARKING IS REQUIRED OUTSIDE OF THE SPECIFICATION, IT SHOULD BE SO SPECIFIED ON THE ORDER) Thickness Range, Inches Plate Flat Sheet Coiled Sheet¹ $0.05 INQUIRY $0.06 Circles & Blanks 6.0000-.0600 .0599-.0180 .0179-.0060 $0.08 $0.02 $0.10 INQUIRY $0.02 INQUIRY Fed. Std. No. 184 ASME & ASTM NO CHARGE NO CHARGE NO CHARGE Non-Standard Markings INQUIRY INQUIRY INQUIRY Standard Marking includes - "Alcoa," alloy, temper, thickness and, if applicable the government specification, ASME or ASTM ¹ Marking will be placed on the ID or the OD of the coil. SPECIAL IDENTIFICATION MARKINGS Extra Per Pound (Extras in Addition to Standard Marking Charges) (WHEN MARKING IS REQUIRED, IT SHOULD BE SO SPECIFIED ON THE ORDER) Inches 6.0000 to .0060 Non-Standard Identification. "CLOSE TOL" in standard marking stencilling band (one or both sides). Technical data i.e. tensile tests-spot marked (one end). Customer's spec or part no. included in standard marking band. Lot no. identification-spot marked (one end). Per Pound $0.01 PROTECTIVE TAPE COATING – Extra Per Square Foot Specification Limitations Weight per piece--maximum 1,200 pounds. Thickness--maximum .3750 in.--minimum .0250 in. Width--maximum 96 in.--minimum 36 in. Length--maximum 296 in.--minimum 72 in. One Side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Plate Flat Sheet $0.54 ♦ INQUIRY for other sizes. Protective tape is not recommended for applications where more than 180 days may elapse before removal of tape. ♦indicates change from or addition to previous issue Tables do not indicate availability. Refer to Product Data for thickness, width, length and temper limitations. A L C O A 1990 April 18 P R I C E North American Rolled Products Reprinted 2007 November 20 NO CHANGE 6 D A T A Section S&P 101 Alcoa Inc. CORES—Price Per Piece Except as indicated COILED SHEET Core Length, Inches Core Size, I.D., Inches Type Available Tempers Aluminum O 2.99- & less 3.0011.99 12.0024.00 24.0136.00 36.0148.00 48.0160.00 ♦$3.00 per pound of core Steel O INQUIRY INQUIRY 3 Fiber All except O INQUIRY $1.39 $3.33 $5.55 $8.00 $7.77 $9.99 4 Fiber All except O INQUIRY 1.50 3.65 6.10 8.55 11.00 Aluminum O 6 Fiber All except O INQUIRY $1.69 $4.05 $6.75 $9.45 $12.15 9 Fiber All except O INQUIRY 2.15 5.17 8.61 6.94 15.5 12 Fiber All except O INQUIRY 2.28 5.47 9.12 12.77 16.42 16 Fiber All except O INQUIRY 2.41 5.78 9.63 13.48 18.11 ♦$3.00 per pound of core 20 Fiber All except O INQUIRY 2.55 6.12 10.89 14.40 21.43 Cores are recommended for all widths of coiled sheet in the thickness range of .006 to .010 in. and are supplied at mill's option at NO CHARGE. FIBER CORES are available on a nonreturnable basis. The weight of the fiber cores is deducted and considered as a part of the tare weight of the shipment. ALUMINUM CORES are available on a nonreturnable basis. The combined weight of the cores and aluminum will constitute the check weight of the shipment. STEEL CORES are available on a returnable basis. The combined weight of the cores and aluminum will constitute the check weight of the shipment. STEEL CORES are available on a returnable basis. Cores in good condition will be accepted for return, at invoice prices, in MINIMUM LOTS OF 10, F.O.B. plant of origin. The combined weight of steel cores and aluminum will constitute the check weight of a shipment. The weight of steel cores is deducted and the cores are invoiced as a separate item. SEPARATORS—Extras Per Pound Coil Width, Inches .500-.999 1.0000 and Over $0.02 0.01 INTERLEAVING OR OILING Interleaving or oiling, in the following table, is necessary for surface protection during shipment. Interleaving or oiling, if required or if not required, must be so specified on orders for these products. If this protection is not desired, Alcoa is not responsible for surface defects resulting from the absence of this protection. Heat Treatable Alloy--Plate & Flat Sheet NO CHARGE Mill Finish Nonheat-Treatable Alloy--Plate &Flat Sheet (Except shipyard and Storage Tank Plate and Sheet) NO CHARGE If interleaving or oiling is required on the following products, the extra charges as indicated will apply. Plate & Flat Sheet Products not listed above Coiled Sheet other than O Temper (oiling) Coiled Sheet O Temper (oiling) ♦indicates change from or addition to previous issue Tables do not indicate availability. Refer to Product Data for thickness, width, length and temper limitations. $0.01 $0.01 INQUIRY A L C O A 2007 November 20 Supersedes Previous Page Dated 2005 December 1990 June21 1 P R I C E 1 7 D A T A North American Rolled Products Section S&P 101 Alcoa Inc. PACKING – EXTRA PER POUND³ PLATE, FLAT SHEET & CIRCLES COILED SHEET Type of Packing (Max Gross Skid Weight) Type of Packing (Max Gross Skid Weight) Bulk or Skids¹ Bulk or Skids¹ 4,500¹ and over BASE 4,500¹ and over BASE 4,499 - 2,500 $0.04 4,499 - 2,500 $0.03 2,499 - 1,500 $0.09 2,499 - 1,500 $0.05 ¹ Bulk packing not available for Flat Sheet or Sheet Circles. ² Maximum net weight for circles is 6,000 pounds. When the item weight is less than the weight of the specified packing, the item weight determines the packing extra. Multiple Item Skid Packing is not permitted. ³ ♦ Repacking is subject to inquiry. EXPORT PACKING FOR WATER SHIPMENT IN ADDITION – to domestic packing extras. Max Gross Skid Wt. Per Pound 4,500 and over $0.05 4,499 - 1,000 $0.07 COILED SHEET PACKED ON HORIZONTAL AXIS IN ADDITION – to Coiled Sheet packing extras. Type of Packing Non-Suspended, Non Stackable Non-Suspended, Stackable Max Gross Skid Wt. Per Pound 1,000 lbs. and over INQUIRY Suspended Arborº ºSuspended arbor is restricted to: 3 inch I.D. flush fiber, aluminum and steel cores, 3 inch and 6 inch I.D. extended steel cores ♦TEST MATERIAL SAMPLES Test material samples will be supplied with production material upon request. Priced the same as the production material (per pound basis) or Minimum charge of $60.00, whichever is greater. ♦indicates change from or addition to previous issue Tables do not indicate availability. Refer to Product Data for thickness, width, length and temper limitations.