Driving High Power LEDs at 700mA with LED Controller IC ILD4120 Application Note 270 http://www.infineon.com/lowcostleddriver Rev. 1.1, 2011-09-13 Power Management & Multimarket Edition 2011-09-13 Published by Infineon Technologies AG 81726 Munich, Germany © 2011 Infineon Technologies AG All Rights Reserved. LEGAL DISCLAIMER THE INFORMATION GIVEN IN THIS APPLICATION NOTE IS GIVEN AS A HINT FOR THE IMPLEMENTATION OF THE INFINEON TECHNOLOGIES COMPONENT ONLY AND SHALL NOT BE REGARDED AS ANY DESCRIPTION OR WARRANTY OF A CERTAIN FUNCTIONALITY, CONDITION OR QUALITY OF THE INFINEON TECHNOLOGIES COMPONENT. THE RECIPIENT OF THIS APPLICATION NOTE MUST VERIFY ANY FUNCTION DESCRIBED HEREIN IN THE REAL APPLICATION. INFINEON TECHNOLOGIES HEREBY DISCLAIMS ANY AND ALL WARRANTIES AND LIABILITIES OF ANY KIND (INCLUDING WITHOUT LIMITATION WARRANTIES OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS OF ANY THIRD PARTY) WITH RESPECT TO ANY AND ALL INFORMATION GIVEN IN THIS APPLICATION NOTE. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 Application Note AN270 Revision History: 13 September 2011 Previous Revision: Previous_Revision_Number Page Subjects (major changes since last revision) Application Note AN270, 0.4 3 / 17 13 September 2011 Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 Table of Contents 1 Introduction ..................................................................................................................................................... 5 2 Application Information............................................................................................................................... 7 3 Characteristic Graphs for different Inductors, no. of LEDs, Rs...................................................... 11 4 Evaluation Board and layout Information............................................................................................. 14 List of Figures Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Figure 11 Figure 12 Figure 13 Figure 14 Figure 15 Figure 16 Figure 17 Figure 18 Figure 19 Figure 20 Figure 21 Figure 22 ILD4120 ................................................................................................................................................ 5 Schematic of the demonstration board ................................................................................................ 7 Measurement setup for measuring Vsense voltage w.r.t. Vs pin ........................................................ 8 Vsw, Vsense and VLED(-), Vs=12 ...................................................................................................... 8 Switching Freq. vs Input Voltage,Vs .................................................................................................... 8 Dimming Waveforms ........................................................................................................................... 9 Maximum Contrast Ratio vs Dimming Frequency (100:1=1% duty) ................................................... 9 Analog Dimming Characteristic ........................................................................................................... 9 ILED vs Vs (Rs=0.187 , L=68µH) ................................................................................................... 11 ILED vs Vs (Rs=0.100 , L=33µH) .................................................................................................... 11 Frequency vs Vs (Rs=0.187 , L=68µH) ........................................................................................... 11 Frequency vs Vs (Rs=0.100 , L=33µH) ........................................................................................... 11 Efficiency vs Vs (Rs=0.187 , L=68µH) ............................................................................................. 12 Efficiency vs Vs (Rs=0.100 , L=33µH) ............................................................................................. 12 I_LED vs Ambient Temperature ....................................................................................................... 13 Efficiency vs Ambient Temperature................................................................................................... 13 Solder Point Temperature vs Ambient Temperature......................................................................... 13 Photograph of Demo Board (size of PCB: 50mm x 30mm) .............................................................. 14 PCB Layer Information Top View ...................................................................................................... 14 PCB Layer information Bottom View (unflip) ..................................................................................... 14 Thermal Resistance of PCB-FR4 versus Ground Copper Area ........................................................ 15 Thermal Resistance .......................................................................................................................... 16 List of Tables Table 1 Table 2 Table 3 Demo Board for ILD4120 ............................................................................................................................... 6 Bill-of-Materials ................................................................................................................................................ 7 Percentage of max LED current vs DC voltage at PWM pin .................................................................. 10 Application Note AN270, 0.4 4 / 17 13 September 2011 Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 1 Introduction 1.1 Features Wide Input Voltage Range: 4.5 V ... 40 V Internal switch for up to 1200 mA average LED current Over current protection Over voltage protection Temperature protection mechanism Inherent open-circuit LED protection Soft- Start capability Low shut down current Analog and PWM dimming possible Typical 3% output current accuracy Minimum external components required Package: DSO-8 with exposed pad 1.2 Figure 1 ILD4120 Applications LED driver for general lighting applications Retail, office and residential luminaires and downlights LED replacement lamps Architectural lighting 1.3 Description This document contains informations about the LED-Less Demonstration Board for ILD4120. ILD4120 is a hysteretic buck LED driver IC for industrial applications. Please refer to the datasheet for the pins descriptions, functions descriptions and specifications. ILD4120 maintains a constant current through a string of LEDS as long as the input voltage exceeds the sum of the forward voltages of the LEDs in the string by at least 3 V. The maximum input voltage for this demonstration board must not exceed 30 V due to the board is optimizing for the 30 V operation. If there is a need to test the board with a maximum supply voltage of 40 V, please replace the schottky diode SD1 with a suitable breakdown voltage. The ILD4120 incorporates the following protection features: Over-voltage protection, temperature shut down and an over-current protection. The board includes a “PWM” input terminal for digital or analog dimming control signal. PWM dimming frequencies upto 300 Hz at 100:1 3 dB contrast ratio and at 100 Hz 3 dB contrast ratio of 300:1 are possible. Higher LED current dimming ratios can be still achieved if higher deviations between PWM duty cycle and LED current ratio are accepted. The demonstration board is designed to operate at ambient temperatures up to 100 °C. The complete demonstration board schematic is shown in curves are shown in Figure 4 to Figure 8. Figure 2. Typical waveforms and performance Although a wide variety of LED combinations and currents can be driven with the ILD4120, the sense-resistors have to be altered to achieve maximum current of 1200 mA and inductance has to be changed to attain recommended switching frequencies below 500 kHz. Application Note AN270, 0.4 5 / 17 13 September 2011 Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 Table 1 Demo Board for ILD4120 R1 R2 R3 L1 Vs Board Name / ILD4120 Demoboard / / 0.56 0.56 0.56 /H /V 68 12 Suitable number of LEDs 3 Typical Switch. Freq. Measured Vrsense = Vs - VLED+ LED Average Current /kHz /V /A 77 0.117 0.625 The above measured values are for typical case only. 1.3.1 Check List before powering up Before powering on the ILD4120 demonstration board, please verify the following: Be sure that each LED can conduct 600 mA DC current within its safe region of operation. Make sure that the input voltage supply is less than 30 V. Select the appropriate mode for EN/PWM: to enable the ILD4120, please force the EN pin terminal to 2.5 V or more, and to select analog dimming, supply a dc source (0 to 3 V) to PWM pin terminal, or to select PWM dimming, supply a PWM signal source from 0 V to 2.5 V. 1.3.2 Capacitor C20 for Ripple Reduction This capacitor C20 is optional and not installed on the standard demo board. The capacitor can help to reduce 1 LED ripple current. Recommended to use low ESR capacitor and its rated voltage must be higher than the maximum input voltage. 1.3.3 Connection of LEDs 2 The ILD4120 demo board includes a 3-pin SIP connector for the anode connection (LED +) and a 2-pin SIP connector for the cathode connection (LED -) of the “LEDs in series”. The anode connection is labeled as CON1- 3 and cathode connection is labeled as CON2-1 on the board. 1.3.4 PWM Dimming The PWM terminal on the PCB is an input for the pulse width modulated (PWM) signal to control the dimming of the LED string. The PWM signal’s logic high level should be at least 2.5 V or higher. For the default demo board circuit, a dimming frequency less than 300 Hz is recommended to maintain a 3 dB contrast ratio of at least 100:1. The 3 dB contrast ratio is shown on Figure 7, and the minimum is based on the measured average LED current at 3 dB below the linear reference. Higher LED current dimming ratios can be still achieved if higher deviations between PWM duty cycle and LED current ratio are accepted. The achievable dimming ratio of the LED current depends mainly on the rise and fall time of the LED current and is thus dependent on supply voltage, LED string forward voltage and inductance value. In addition, if C20 is installed, the maximum contrast ratio or DIM frequency will be further reduced. 1.3.5 Open Circuit of terminals LED+ and LED- If the LED array is disconnected or fails with open state, the ILD4120 will operate at 100% duty cycle. The output voltage (at LED+) will rise to the level of the input voltage. The other output terminal (LED -) will fall to 1 2 Equivalent Series Resistance Single In-line Package Application Note AN270, 0.4 6 / 17 13 September 2011 Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 ground. Note that under the above said condition; please avoid reconnecting the LED array between LED+ and LED- terminals without powering down first. This precaution is to avoid excessive surge current that may damage the LEDs in the case when C20 is assembled. 2 Application Information 2.1 Schematic Figure 2Schematic of the demonstration board Table 2 Bill-of-Materials Symbol Value Unit Size Manufacturer Comment L1 68 µH 7.3x7.3mm EPCOS Shielded Power Inductor, 20%, 0.82 A R1 0.56 Ω 1206 Part of the current sense resistor R2 0.56 Ω 1206 Part of the current sense resistor R3 0.56 Ω 1206 Part of the current sense resistor R10 SD1 IC1 0 BAS3020B ILD4120 Ω 0805 SOT363 DSO-8 C30 4.7 µF Application Note AN270, 0.4 Jumper INFINEON INFINEON 1812 Medium Power AF Schottky Diode 2 A 30 V Hysteretic Buck controller and LED driver Ceramic, 50 V 7 / 17 13 September 2011 Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 2.2 Recommended method to measure Vsense w.r.t. Vs pin Figure 3 Measurement setup for measuring Vsense voltage w.r.t. Vs pin By probing Vsense pin voltage with reference to Vs pin, it facilitates the observation and measurement of the ripple and average of Vsense voltage at the same time with “Oscilloscope set to DC coupling”, and without offsetting the DC voltage. This is shown in Figure 4, waveform 3. 2.3 Measured Graphs of the demonstration boards Unless otherwise specified, the following condition labels apply: Condition 12 V: Vs = 12 V, Ta = 25 C Figure 4 Figure 5 Vsw, Vsense and VLED(-), Vs=12 Application Note AN270, 0.4 8 / 17 Switching Freq. vs Input Voltage,Vs 13 September 2011 Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 Figure 6 Dimming Waveforms Figure 7 3 dB Contrast Ratio vs Dimming Frequency (100:1=1% duty) Application Note AN270, 0.4 Figure 8 Analog Dimming Characteristic 9 / 17 13 September 2011 Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 2.4 Analog Dimming Characteristic The analog dimming characteristic graph is shown Figure 8. To achieve a linear change in LED current versus control voltage, the recommended range of voltage at EN/PWM pin is from 0.8 V to 2.5 V. Table 3 Percentage of max LED current vs DC voltage at PWM pin Ven_pwm /V 2.5 Percentage of max. LED Current /% < 0.5 0.8 0 10 1.1 1.5 25 50 1.9 2.2 75 90 >2.5 100 Temperature Protection ILD4120 incorporates a temperature protection circuit referring to the junction temperature of ILD4120. The higher the junction temperature of ILD4120 the lower the current of the LEDs. This feature helps to reduce the power dissipation of ILD4120 and the LEDs. Yet still the product specific maximum ratings for junction temperature need to be observed to avoid a permanent damage of the devices. The ILED temperature characteristic is shown on Figure 15. The LED current is reduced by 10% when the ambient temperature reaches 90 °C for 12 V, 3 LEDs case. 2.6 Setting the nominal LED current The internal reference for the voltage across the external sense resistor was design to be 0.117 V as stated in the datasheet. A first order approximation for the LED current can be calculated with this formula: V I LED sense R sense 0.117 V R sense If a certain level of LED current is desired; the estimation for the Rsense is given by: V R sense sense I LED 0.117 V I LED The Vsense can vary depending on the number of LEDs and voltage supply. Please take reference from Figure 9 and Figure 10. Application Note AN270, 0.4 10 / 17 13 September 2011 Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 3 Characteristic Graphs for different Inductors, no. of LEDs, Rs 3.1 ILED, Switching Frequency versus Supply Voltage Characteristics Figure 9 ILED vs Vs (Rs=0.187, L=68µH) Figure 10 ILED vs Vs (Rs=0.100, L=33µH) 1 Figure 11 Frequency vs Vs (Rs=0.187, L=68µH) 1 Figure 12 Frequency vs Vs (Rs=0.100, L=33µH) 1 For Rs=0.100Ω, the operating voltage range needs to be checked not to violate absolute maximum rating of the IC. Application Note AN270, 0.4 11 / 17 13 September 2011 Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 3.2 Efficiency versus Supply Voltage Characteristics Figure 13 Efficiency vs Vs (Rs=0.187, L=68µH) Figure 14 Efficiency vs Vs (Rs=0.100, L=33µH) 1 1 For Rs=0.100Ω, the operating voltage range needs to be checked not to violate absolute maximum rating of the IC. Application Note AN270, 0.4 12 / 17 13 September 2011 Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 3.3 Temperature Characteristics (Rs=0.187 L=68µH) Figure 15 I_LED vs Ambient Temperature Figure 17 Solder Point Temperature vs Ambient Temperature. Figure 16 Efficiency vs Ambient Temperature Application Note AN270, 0.4 13 / 17 13 September 2011 Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 4 Evaluation Board and Layout Information Figure 18 Photograph of Demo Board (size of PCB: 50mm x 30mm) Figure 19 PCB Layer Information Top View Figure 20 PCB Layer information Bottom View (unflip) Application Note AN270, 0.4 14 / 17 13 September 2011 Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 4.1 PCB Consideration The free-wheeling diode’s path from inductor to Vs pin of the integrated circuit is recommended to be as short a distance as possible. This is to minimize oscillation in the system. The energy storage capacitor between Vs and Gnd is recommended to be placed as near to the IC as possible. This helps to stabilize the supply voltage when the IC draws large instantanoeus current during switching. Ground plane should be as large as possible to improve heat dissipation. As a reference for designing the surface area for the grounding for the PCB using FR4 to achieve a certain thermal resistance between desired solder point temperature and expected ambient temperature, the following chart can be used. Figure 21 Thermal Resistance of PCB-FR4 versus Ground Copper Area The data in the above Figure 21 were measured with following conditions: Two copper layers. 2 oz copper (70 µm thick) and board thickness of about 1.6 mm. Ground pin connection of the IC is used to dissipate heat. FR4 material. No forced convection. No heat sink. No special mask opening for improved heat dissipation. In the chart, only three points are marked by diamond symbol. These are measured data. The broken line represents intermediate points which can de derived by linear interpolation. Application Note AN270, 0.4 15 / 17 13 September 2011 Application Note AN270 Driving High Power LEDs at 700mA with LED Controller IC ILD4120 An example where ILD4120’s PCB is separated from LED PCB and there is not heat transmission between the two PCBs. Figure 22 Thermal Resistance Tj is the junction temperature of the ILD4120’s output transistor connected to switch pin. Ts is the soldered temperature of the ILD4120’s ground pin to FR4-PCB. Ta is the ambient temperature. Rth_js is the thermal resistance from junction to soldered point with reference to ILD4120’s DSO-8 package. This is stated as 15 K/W in the datasheet. Rth_sa is the thermal resistance from soldered point to ambient which is dependent on size of grounding area of PCB. Pd is the power dissipated by ILD4120 which is approximately 10% of total power from supply (for rough calculation), or it can be derived by (Total power from supply – LEDs’ power – Power Loss on other external components). The above variables are related in the equations on the next line. P d T j Ts R th _ js T T s R a th _ sa With the above equations, and setting T j (recommended to be below 100 °C), the Ts can be calculated. By choosing a desired Ta, the Rth_sa can be calculated. With the calculated Rth_sa, reference Figure 21 to correlate the approximated ground copper area required in PCB layout. Application Note AN270, 0.4 16 / 17 13 September 2011 www.infineon.com Published by Infineon Technologies AG AN270