LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SUPER BRIGHT ROUND TYPE LED LAMPS Pb Lead-Free Parts LURF3633S/S3/A-PF DATA SHEET DOC. NO : QW0905- LURF3633S/S3/A-PF REV. : A DATE : 05-May. - 2015 發行 立碁電子 DCC LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO.LURF3633S/S3/A-PF Page 1/7 Package Dimensions 10.0 11.0 13.5 1.5MAX 2.0 25.0MIN □0.5 TYP 1.0MIN 2.54TYP + Note : 1.All dimension are in millimeter tolerance is ±0.25mm unless otherwise noted. 2.Specifications are subject to change without notice. Directivity Radiation 0° -30° 30° -60° 100% 75% 50% 60° 25% 0 25% 50% 75% 100% LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO.LURF3633S/S3/A-PF Page 2/7 Absolute Maximum Ratings at Ta=25 ℃ Ratings Symbol Parameter UNIT URF(S) Forward Current IF 50 mA Peak Forward Current Duty 1/10@10KHz IFP 90 mA Power Dissipation PD 120 mW Ir 10 μA Electrostatic Discharge( * ) ESD 2000 V Operating Temperature Topr -40 ~ +85 ℃ Storage Temperature Tstg -40 ~ +100 ℃ Reverse Current @5V Typical Electrical & Optical Characteristics (Ta=25 ℃) PART NO LURF3633S/S3/A-PF COLOR MATERIAL AlGaInP Emitted Lens Red Water Clear Forward Dominant Spectral voltage wave halfwidth length △λ nm @20mA(V) λDnm Luminous intensity @25mA(mcd) Viewing angle 2 θ 1/2 (deg) Min. Max. Min. Typ. 625 20 1.7 Note : 1.The forward voltage data did not including ±0.1V testing tolerance. 2. The luminous intensity data did not including ±15% testing tolerance. 2.6 9500 17000 25 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only Page 3/7 PART NO. LURF3633S/S3/A-PF Brightness Code For Standard LED Lamps Bin Code Group Luminous Intensity(mcd) at 25 mA Min. Max. A32 9500 11500 A33 11500 14000 A34 14000 17000 A35 17000 21000 A36 21000 26000 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO.LURF3633S/S3/A-PF Page 4/7 Typical Electro-Optical Characteristics Curve URFS CHIP Fig.2 Luminous Intensity vs. Forward Current 6.0 150 Luminous Intensity Normalize @20mA Forward Current(mA) Fig.1 Forward current vs. Forward Voltage 100 50 0 0.5 0 1.0 1.5 2.0 2.5 5.0 4.0 3.0 2.0 1.0 0.0 0 3.0 50 1.06 1.04 1.02 1.00 0.98 0.96 0.94 0 20 40 60 80 100 Relative Intensity@20mA Fig.5 Relative Intensity vs. Wavelength 1.0 0.5 0 600 650 Wavelength (nm) 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -40 -20 0 20 40 60 Ambient Temperature( ℃) Ambient Temperature( ℃) 550 Fig.4 Luminous Intensity vs. Temperature Luminous Intensity@20mA Normalize @25℃ Forward Voltage@20mA Normalize @25℃ Fig.3 Forward Voltage vs. Temperature -20 150 Forward Current(mA) Forward Voltage(V) -40 100 700 80 100 LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO.LURF3633S/S3/A-PF Page 5/7 Soldering Condition(Pb-Free) 1.Iron: Soldering Iron:30W Max Temperature 350 ° C Max Soldering Time:3 Seconds Max(One time only) Distance:2mm Min(From solder joint to body) 2.Wave Soldering Profile Dip Soldering Preheat: 120°C Max Preheat time: 120seconds Max Ramp-up 2° C/sec(max) Ramp-Down:-5° C/sec(max) Solder Bath:260°C Max Dipping Time:3 seconds Max Distance:2mm Min(From solder joint to body) Temp(° C) 260° C3sec Max 260° 5° /sec max 120° 25° 0° 0 2° /sec max Preheat 100 200 120 Seconds Max Note: 1.Wave solder should not be made more than one time. 2.You can just only select one of the soldering conditions as above. 250 Time(sec) LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only PART NO.LURF3633S/S3/A-PF Page 6/7 Reliability Test: Test Item Test Condition Description Reference Standard Operating Life Test 1.Under Room Temperature 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs) This test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. MIL-STD-750: 1026 MIL-STD-883: 1005 JIS C 7021: B-1 High Temperature Storage Test 1.Ta=105 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of high temperature for hours. MIL-STD-883:1008 JIS C 7021: B-10 Low Temperature Storage Test 1.Ta=-40 ℃±5℃ 2.t=1000 hrs (-24hrs, +72hrs) The purpose of this is the resistance of the device which is laid under condition of low temperature for hours. High Temperature High Humidity Test 1.Ta=65 ℃±5℃ 2.RH=90 %~95% 3.t=240hrs ±2hrs The purpose of this test is the resistance of the device under tropical for hours. Thermal Shock Test 1.Ta=105 ℃±5℃ &-40 ℃±5 ℃ (10min) (10min) 2.total 10 cycles The purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. MIL-STD-202: 107D MIL-STD-750: 1051 MIL-STD-883: 1011 Solder Resistance Test 1.T.Sol=260 ℃±5℃ 2.Dwell time= 10 ±1sec. This test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. MIL-STD-202: 210A MIL-STD-750: 2031 JIS C 7021: A-1 Solderability Test 1.T.Sol=245 ℃±5℃ 2.Dwell time=5 ±1sec This test intended to see soldering well performed or not. MIL-STD-202: 208D MIL-STD-750: 2026 MIL-STD-883: 2003 JIS C 7021: A-2 JIS C 7021: B-12 MIL-STD-202:103B JIS C 7021: B-11 PACKING SPECIFICATION Page 7/7 1. 250PCS / BAG 2. 8 BAG / INNER BOX SIZE : L X W X H 33cm X 19cm X 8cm L W H 3. 12 INNER BOXES / CARTON SIZE : L X W X H 58cm X 34cm X 34cm L W C/NO: MADE IN CHINA . NO M IT E Y : Q'T ,: W : N, , W G, S PC s kg s kg H