AZ AZ2501L 60 AMP LATCHING POWER RELAY FEATURES • • • • • • 60 Amp switching Heavy loads to 15000 VA Inrush current 500A/2ms max. 4 kV dielectric Manual switch standard UL, CUR file E44211 GENERAL DATA CONTACTS Arrangement SPST (1 Form A) (1 Form B) Ratings Resistive load: Max. Max. Max. Max. UL/CUR switched power: 15000 VA switched current: 60 A switched voltage: 440 VAC continuous current: 20 A 20 A at 277 VAC, Resistive, 85°C, 100k cycles 20 A at 30 VDC, Resistive, 85°C, 100k cycles 60 A at 250 VAC, General use, 85°C 30k cycles 5000 W at 250 VAC, Tungsten, 30k cycles 20 A at 277 VAC, Standard Ballast, 30k cycles 16 A at 277 VAC, Electronic Ballast, 30k cycles Material Silver tin oxide Resistance < 50 milliohms initially (24 V, 1 A voltage drop method) Life Expectancy Mechanical Electrical Minimum operations 1 x 106 3 x 104 at rated load Set and Reset Pulse Duration 50 ms minimum Set Time (typical) 15 ms at nominal coil voltage Reset Time (typical) 15 ms at nominal coil voltage Dielectric Strength 4000 Vrms coil to contact (at sea level for 1 min.) 1500 Vrms between open contacts Insulation Resistance 1000 megohms min. at 20°C, 500 VDC, 50% RH Creepage Distance 8 mm Ambient Temperature Operating At nominal coil voltage -40°C (-40°F) to 85°C (158°F) Vibration 0.059" DA at 10–55 Hz Shock Operating 10 g Non-Operating 100 g COIL Power At Pickup Voltage (typical) .92 W single coil 1.8 W dual coil Temperature NOTES Enclosure P.B.T. polyester Terminals Tinned copper alloy Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Weight 32 grams 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 12/16/13 AZ AZ2501L RELAY ORDERING DATA COIL SPECIFICATIONS -Standard Single Coil Nominal Coil VDC 6 12 24 48 Must Operate VDC 4.8 9.6 19.2 38.4 ORDER NUMBER* Max. Continuous VDC [1] 7.8 15.6 31.2 62.4 Coil Resistance ± 10% 22 100 360 1600 COIL SPECIFICATIONS -Standard Dual Coil 1 Form A AZ2501LP1–1A–6D AZ2501LP1–1A–12D AZ2501LP1–1A–24D AZ2501LP1–1A–48D 1 Form B AZ2501LP1–-1B–6D AZ2501LP1–-1B–12D AZ2501LP1–-1B–24D AZ2501LP1–-1B–48D ORDER NUMBER* Nominal Coil Must Operate Max. Continuous Coil Resistance VDC VDC VDC [1] ± 10% 6 4.8 7.8 11 + 11 12 9.6 15.6 50 + 50 24 19.2 31.2 180 + 180 48 38.4 62.4 800 + 800 * For reverse polarity coil add suffix “R”. NOTE: [1] Max. continuous voltage should not be applied for 1 Form A AZ2501LP2–1A–6D AZ2501LP2–1A–12D AZ2501LP2–1A–24D AZ2501LP2–1A–48D more then 30 seconds 1 Form B AZ2501LP2–-1B–6D AZ2501LP2–-1B–12D AZ2501LP2–-1B–24D AZ2501LP2–-1B–48D (Bottom View) MECHANICAL DATA If no tolerance is shown: outline dimension <= 1mm, tolerance is ±0.2mm; outline dimension > 1mm and <=5mm, tolerance is ±0.3mm; outline dimension >5mm, tolerance is ±0.4mm. 12/16/13 AZ2501L NOTE: Regarding Standard Polarity type: 1. “Single Coil Latching Version” (1) After energizing 1 (-) and 2 (+), 50ms pulse, terminal 3 and 4 is connected. (2) After energizing 2 (-) and 1 (+), 50ms pulse, terminal 3 and 4 is disconnected. 2. “Double Coil Latching Version” (1) After energizing 5 (+) and 1 (-), 50ms pulse, terminal 3 and 4 is connected. (2) After energizing 5 (+) and 2 (-) , 50ms pulse, terminal 3 and 4 is disconnected. Regarding Reverse Polarity type: 1. “Single Coil Latching Version” (1) After energizing 1 (+) and 2 (-), 50ms pulse, terminal 3 and 4 is connected. (2) After energizing 2 (+) and 1 (-), 50ms pulse, terminal 3 and 4 is disconnected. 2. “Double Coil Latching Version” (1) After energizing 5 (+) and 2 (-), 50ms pulse, terminal 3 and 4 is connected. (2) After energizing 5 (+) and 1 (-), 50ms pulse, terminal 3 and 4 is disconnected. 5/14/13