LM339 D

LM339, LM339E, LM239,
LM2901, LM2901E,
LM2901V, NCV2901,
MC3302
Single Supply Quad
Comparators
www.onsemi.com
These comparators are designed for use in level detection, low−level
sensing and memory applications in consumer, automotive, and
industrial electronic applications.
1
Features
•
•
•
•
•
•
•
•
•
•
•
SOIC−14
D SUFFIX
CASE 751A
14
Single Supply Operation: 3.0 V to 36 V
Split Supply Operation: ±1.5 V to ±18 V
Low Input Bias Current: 25 nA (Typ)
Low Input Offset Current: ±5.0 nA (Typ)
Low Input Offset Voltage
Input Common Mode Voltage Range to GND
Low Output Saturation Voltage: 130 mV (Typ) @ 4.0 mA
TTL and CMOS Compatible
ESD Clamps on the Inputs Increase Reliability without Affecting
Device Operation
NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
PDIP−14
N, P SUFFIX
CASE 646
14
1
TSSOP−14
DTB SUFFIX
CASE 948G
14
1
PIN CONNECTIONS
Output 2
1
14
Output 3
Output 1
2
13
Output 4
VCC
3
12
GND
- Input 1
4
11
+ Input 4
10
- Input 4
9
+ Input 3
8
- Input 3
+ Input 1
5
- Input 2
6
+ Input 2
7
*
1
)
4
*2
)
3
)
*
)
*
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 7 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 8 of this data sheet.
© Semiconductor Components Industries, LLC, 2016
January, 2016 − Rev. 22
1
Publication Order Number:
LM339/D
LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302
MAXIMUM RATINGS
Rating
Symbol
Power Supply Voltage
VCC
LM239/LM339, E/LM2901, E, V
MC3302
Input Differential Voltage Range
Value
Vdc
+36 or ±18
+30 or ±15
VIDR
Vdc
36
30
LM239/LM339, E/LM2901, E, V
MC3302
Input Common Mode Voltage Range
VICMR
−0.3 to VCC
Output Short Circuit to Ground (Note 1)
ISC
Continuous
Power Dissipation @ TA = 25°C
Plastic Package
Derate above 25°C
PD
Junction Temperature
Operating Ambient Temperature Range
Vdc
1/RqJA
1.0
8.0
W
mW/°C
TJ
150
°C
°C
TA
−25 to +85
−40 to +85
−40 to +105
−40 to +125
0 to +70
LM239
MC3302
LM2901, LM2901E
LM2901V, NCV2901
LM339, LM339E
Storage Temperature Range
Unit
Tstg
−65 to +150
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC. Output short circuits to VCC can cause excessive
heating and eventual destruction.
ESD RATINGS
Rating
ESD Protection at any Pin (Human Body Model − HBM, Machine Model − MM)
NCV2901
LM339E, LM2901E
LM339DR2G, LM2901DR2G
All Other Devices
VCC
- Input
+ Input
GND
NOTE: Diagram shown is for 1 comparator.
Figure 1. Circuit Schematic
www.onsemi.com
2
HBM
MM
Unit
2000
1500
250
1500
200
200
100
200
V
V
V
V
Output
LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302
ELECTRICAL CHARACTERISTICS (VCC = +5.0 Vdc, TA = +25°C, unless otherwise noted)
LM239/339/339E
LM2901/2901E/2901V
/NCV2901
MC3302
Symbol
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
Input Offset Voltage (Note 3)
VIO
−
±2.0
±5.0
−
±2.0
±7.0
−
±3.0
±20
mVdc
Input Bias Current (Notes 3, 4)
IIB
−
25
250
−
25
250
−
25
500
nA
IIO
−
±5.0
±50
−
±5.0
±50
−
±3.0
±100
nA
VICMR
0
−
VCC
−1.5
0
−
VCC
−1.5
0
−
VCC
−1.5
V
Characteristic
(Output in Analog Range)
Input Offset Current (Note 3)
Input Common Mode Voltage Range
Supply Current
ICC
RL = ∞ (For All Comparators)
−
RL = ∞, VCC = 30 Vdc
Voltage Gain
mA
0.8
2.0
−
0.8
2.0
−
0.8
2.0
−
1.0
2.5
−
1.0
2.5
−
1.0
2.5
AVOL
50
200
−
25
100
−
25
100
−
V/mV
−
−
300
−
−
300
−
−
300
−
ns
−
−
1.3
−
−
1.3
−
−
1.3
−
ms
ISink
6.0
16
−
6.0
16
−
6.0
16
−
mA
Vsat
−
130
400
−
130
400
−
130
500
mV
IOL
−
0.1
−
−
0.1
−
−
0.1
−
nA
RL ≥ 15 kW, VCC = 15 Vdc
Large Signal Response Time
VI = TTL Logic Swing,
Vref = 1.4 Vdc, VRL = 5.0 Vdc,
RL = 5.1 kW
Response Time (Note 5)
VRL = 5.0 Vdc, RL = 5.1 kW
Output Sink Current
VI (−) ≥ +1.0 Vdc, VI(+) = 0,
VO ≤ 1.5 Vdc
Saturation Voltage
VI(−) ≥ +1.0 Vdc, VI(+) = 0,
Isink ≤ 4.0 mA
Output Leakage Current
VI(+) ≥ +1.0 Vdc, VI(−) = 0,
VO = +5.0 Vdc
2. (LM239) Tlow = −25°C, Thigh = +85°
(LM339, LM339E) Tlow = 0°C, Thigh = +70°C
(MC3302) Tlow = −40°C, Thigh = +85°C
(LM2901), LM2901E Tlow = −40°C, Thigh = +105°
(LM2901V & NCV2901) Tlow = −40°C, Thigh = +125°C
NCV2901 is qualified for automotive use.
3. At the output switch point, VO ] 1.4 Vdc, RS ≤ 100 W 5.0 Vdc ≤ VCC ≤ 30 Vdc, with the inputs over the full common mode range
(0 Vdc to VCC −1.5 Vdc).
4. The bias current flows out of the inputs due to the PNP input stage. This current is virtually constant, independent of the output state.
5. The response time specified is for a 100 mV input step with 5.0 mV overdrive. For larger signals, 300 ns is typical.
www.onsemi.com
3
LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302
PERFORMANCE CHARACTERISTICS (VCC = +5.0 Vdc, TA = Tlow to Thigh [Note 6])
LM2901/2901E/2901V
/NCV2901
LM239/339/339E
MC3302
Symbol
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
Unit
Input Offset Voltage (Note 7)
VIO
−
−
±9.0
−
−
±15
−
−
±40
mVdc
Input Bias Current (Notes 7, 8)
IIB
−
−
400
−
−
500
−
−
1000
nA
IIO
−
−
±150
−
−
±200
−
−
±300
nA
VICMR
0
−
VCC
−2.0
0
−
VCC
−2.0
0
−
VCC
−2.0
V
Vsat
−
−
700
−
−
700
−
−
700
mV
IOL
−
−
1.0
−
−
1.0
−
−
1.0
mA
VID
−
−
VCC
−
−
VCC
−
−
VCC
Vdc
Characteristic
(Output in Analog Range)
Input Offset Current (Note 7)
Input Common Mode Voltage Range
Saturation Voltage
VI(−) ≥ +1.0 Vdc, VI(+) = 0,
Isink ≤ 4.0 mA
Output Leakage Current
VI(+) ≥ +1.0 Vdc, VI(−) = 0,
VO = 30 Vdc
Differential Input Voltage
All VI ≥ 0 Vdc
6. (LM239) Tlow = −25°C, Thigh = +85°
(LM339, LM339E) Tlow = 0°C, Thigh = +70°C
(MC3302) Tlow = −40°C, Thigh = +85°C
(LM2901, LM2901E) Tlow = −40°C, Thigh = +105°
(LM2901V & NCV2901) Tlow = −40°C, Thigh = +125°C
NCV2901 is qualified for automotive use.
7. At the output switch point, VO ] 1.4 Vdc, RS ≤ 100 W 5.0 Vdc ≤ VCC ≤ 30 Vdc, with the inputs over the full common mode range
(0 Vdc to VCC −1.5 Vdc).
8. The bias current flows out of the inputs due to the PNP input stage. This current is virtually constant, independent of the output state.
9. The response time specified is for a 100 mV input step with 5.0 mV overdrive. For larger signals, 300 ns is typical.
+ VCC
+ VCC
R3
10 k
Vin
+ VCC
Rref
Rref
10 k
-
Vref
VO
+
R1
R2
Vref
10k
R1
1.0 M
Vref [
R3
Rref + R1
R1 / / Rref
R1/ / Rref + R2
VO
+
10 k
VCC R1
1.0 M
R3 ] R1 / / Rref / / R2
VH =
R2
Vin
10 k
Vref =
VCC R1
Rref + R1
R2 [ R1 / / Rref
Amount of Hysteresis VH
R2
VH =
[(V
-V
]
R2 + R3 O(max) O(min)
[VO(max) - VO(min)]
R2 ơ Rref / / R1
Figure 2. Inverting Comparator
with Hysteresis
Figure 3. Noninverting Comparator
with Hysteresis
www.onsemi.com
4
LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302
Typical Characteristics
(VCC = 15 Vdc, TA = +25°C (each comparator) unless otherwise noted.)
48
42
I IB, INPUT BIAS CURRENT (nA)
1.20
1.00
0.80
TA = -55° C
36
TA = +25° C
30
TA = +125°C
24
18
12
6.0
0
0.60
-50
-25
0
25
50
75
TA, AMBIENT TEMPERATURE (°C)
100
125
0
4.0
8.0
12
16
20
24
VCC, POWER SUPPLY VOLTAGE (Vdc)
Figure 4. Normalized Input Offset Voltage
28
Figure 5. Input Bias Current
8.0
IO, OUTPUT CURRENT (mA)
NORMALIZED OFFSET VOLTAGE
1.40
7.0
TA = +25° C
6.0
TA = -55° C
5.0
TA = +125°C
4.0
3.0
2.0
1.0
0
100
0
200
300
400
500
Vsat, OUTPUT SATURATION VOLTAGE (mV)
Figure 6. Output Sink Current versus
Output Saturation Voltage
VCC
RS
Vin
Vref
VCC ≥ 4.0 V
+
-
VCC
RS = Source Resistance
R1 ] RS
RL
kW
1/4 MC14001
+15
100
1/4 MC7400
+5.0
10
CMOS
TTL
R1
VO
+
R2
R3
330 k
330 k
R4
VCC
(V)
Device
-
+
C
R1
Logic
10 k
100 k
RL
330 k
VCC
T1
T2
T1 = T2 = 0.69 RC
7.2
f[
C(mF)
R2 = R3 = R4
R1 [ R2 // R3 // R4
Figure 7. Driving Logic
Figure 8. Squarewave Oscillator
www.onsemi.com
5
32
LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302
APPLICATIONS INFORMATION
addition of positive feedback (< 10 mV) is also
recommended. It is good design practice to ground all
unused input pins.
Differential input voltages may be larger than supply
voltages without damaging the comparator’s inputs.
Voltages more negative than −300 mV should not be used.
These quad comparators feature high gain, wide
bandwidth characteristics. This gives the device oscillation
tendencies if the outputs are capacitively coupled to the
inputs via stray capacitance. This oscillation manifests itself
during output transitions (VOL to VOH). To alleviate this
situation input resistors < 10 kW should be used. The
+15 V
R1
8.2 k
R4
220 k
D1
6.8 k
R2
Vin
R5
220 k
10 k
*
)
Vin(min) ≈ 0.4 V peak for 1% phase distortion (Dq).
VO
Vin
Vin(min)
VCC
15 k
R3
q
10 M
*
Vin
D1 prevents input from going negative by more than 0.6 V.
R1 + R2 = R3
R5
R3 ≤
for small error in zero crossing
10
+
VEE
10 k
VO
VCC
VEE
Figure 9. Zero Crossing Detector
(Single Supply)
q
VO
Dq
Figure 10. Zero Crossing Detector
(Split Supplies)
www.onsemi.com
6
LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302
ORDERING INFORMATION
Device
LM239DG
LM239DR2G
Package
Shipping†
SOIC−14 (Pb−Free)
55 Units/Tube
SOIC−14 (Pb−Free)
2500 / Tape & Reel
TSSOP−14 (Pb−Free)
2500 / Tape & Reel
LM239NG
PDIP−14 (Pb−Free)
25 Units/Rail
LM339DG
SOIC−14 (Pb−Free)
55 Units/Tube
LM339DR2G
SOIC−14 (Pb−Free)
2500 / Tape & Reel
LM339EDR2G
SOIC−14 (Pb−Free)
2500 / Tape & Reel
LM239DTBR2G
LM339DTBR2G
TSSOP−14 (Pb−Free)
2500 / Tape & Reel
LM339NG
PDIP−14 (Pb−Free)
25 Units/Rail
LM2901DG
SOIC−14 (Pb−Free)
55 Units/Rail
LM2901DR2G
SOIC−14 (Pb−Free)
2500 / Tape & Reel
LM2901EDR2G
SOIC−14 (Pb−Free)
2500 / Tape & Reel
TSSOP−14 (Pb−Free)
2500 / Tape & Reel
LM2901DTBR2G
LM2901NG
PDIP−14 (Pb−Free)
25 Units/Rail
LM2901VDG
SOIC−14 (Pb−Free)
55 Units/Tube
LM2901VDR2G
SOIC−14 (Pb−Free)
2500 / Tape & Reel
TSSOP−14 (Pb−Free)
2500 / Tape & Reel
LM2901VDTBR2G
LM2901VNG
PDIP−14 (Pb−Free)
25 Units/Rail
NCV2901DR2G*
SOIC−14 (Pb−Free)
2500 / Tape & Reel
TSSOP−14 (Pb−Free)
2500 / Tape & Reel
Bare Die
6000 / Tape & Reel
NCV2901DTBR2G*
NCV2901CTR*
MC3302DG
SOIC−14 (Pb−Free)
55 Units/Tube
MC3302DR2G
SOIC−14 (Pb−Free)
2500 / Tape & Reel
TSSOP−14 (Pb−Free)
2500 / Tape & Reel
PDIP−14 (Pb−Free)
25 Units/Rail
MC3302DTBR2G
MC3302PG
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
www.onsemi.com
7
LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302
MARKING DIAGRAMS
PDIP−14
N, P SUFFIX
CASE 646
14
14
14
LM339N
AWLYYWWG
1
14
LM2901N
AWLYYWWG
LM239N
AWLYYWWG
1
1
14
LM2901VN
AWLYYWWG
MC3302P
AWLYYWWG
1
1
SOIC−14
D SUFFIX
CASE 751A
14
14
14
LM339DG
AWLYWW
1
14
LM239DG
AWLYWW
1
LM2901DG
AWLYWW
1
14
14
*
LM2901VDG
AWLYWW
MC3302DG
AWLYWW
1
1
14
LM339EG
AWLYWW
LM2901EG
AWLYWW
1
1
TSSOP−14
DTB SUFFIX
CASE 948G
14
14
339
ALYW G
G
239
ALYW G
G
1
14
1
14
14
2901
V
ALYW G
G
2901
ALYW G
G
1
1
A
= Assembly Location
WL, L = Wafer Lot
YY, Y
= Year
WW, W = Work Week
G or G = Pb−Free Package
(Note: Microdot may be in either location)
*This marking diagram also applies to NCV2901.
www.onsemi.com
8
*
3302
ALYW G
G
1
LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302
PACKAGE DIMENSIONS
PDIP−14
CASE 646−06
ISSUE S
D
14
A
8
E
H
E1
1
NOTE 8
7
b2
c
B
TOP VIEW
END VIEW
WITH LEADS CONSTRAINED
NOTE 5
A2
A
NOTE 3
L
SEATING
PLANE
A1
C
M
D1
eB
END VIEW
e
14X b
SIDE VIEW
0.010
M
C A
M
B
M
NOTE 6
www.onsemi.com
9
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: INCHES.
3. DIMENSIONS A, A1 AND L ARE MEASURED WITH THE PACKAGE SEATED IN JEDEC SEATING PLANE GAUGE GS−3.
4. DIMENSIONS D, D1 AND E1 DO NOT INCLUDE MOLD FLASH
OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS ARE
NOT TO EXCEED 0.10 INCH.
5. DIMENSION E IS MEASURED AT A POINT 0.015 BELOW DATUM
PLANE H WITH THE LEADS CONSTRAINED PERPENDICULAR
TO DATUM C.
6. DIMENSION eB IS MEASURED AT THE LEAD TIPS WITH THE
LEADS UNCONSTRAINED.
7. DATUM PLANE H IS COINCIDENT WITH THE BOTTOM OF THE
LEADS, WHERE THE LEADS EXIT THE BODY.
8. PACKAGE CONTOUR IS OPTIONAL (ROUNDED OR SQUARE
CORNERS).
DIM
A
A1
A2
b
b2
C
D
D1
E
E1
e
eB
L
M
INCHES
MIN
MAX
−−−−
0.210
0.015
−−−−
0.115 0.195
0.014 0.022
0.060 TYP
0.008 0.014
0.735 0.775
0.005
−−−−
0.300 0.325
0.240 0.280
0.100 BSC
−−−−
0.430
0.115 0.150
−−−−
10 °
MILLIMETERS
MIN
MAX
−−−
5.33
0.38
−−−
2.92
4.95
0.35
0.56
1.52 TYP
0.20
0.36
18.67 19.69
0.13
−−−
7.62
8.26
6.10
7.11
2.54 BSC
−−−
10.92
2.92
3.81
−−−
10 °
LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302
PACKAGE DIMENSIONS
SOIC−14
CASE 751A−03
ISSUE K
D
A
B
14
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION
SHALL BE 0.13 TOTAL IN EXCESS OF AT
MAXIMUM MATERIAL CONDITION.
4. DIMENSIONS D AND E DO NOT INCLUDE
MOLD PROTRUSIONS.
5. MAXIMUM MOLD PROTRUSION 0.15 PER
SIDE.
8
A3
E
H
L
1
0.25
M
DETAIL A
7
B
13X
M
b
0.25
M
C A
S
B
S
e
DETAIL A
h
A
X 45 _
M
A1
C
SEATING
PLANE
DIM
A
A1
A3
b
D
E
e
H
h
L
M
MILLIMETERS
MIN
MAX
1.35
1.75
0.10
0.25
0.19
0.25
0.35
0.49
8.55
8.75
3.80
4.00
1.27 BSC
5.80
6.20
0.25
0.50
0.40
1.25
0_
7_
SOLDERING FOOTPRINT*
6.50
14X
1.18
1
1.27
PITCH
14X
0.58
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
10
INCHES
MIN
MAX
0.054 0.068
0.004 0.010
0.008 0.010
0.014 0.019
0.337 0.344
0.150 0.157
0.050 BSC
0.228 0.244
0.010 0.019
0.016 0.049
0_
7_
LM339, LM339E, LM239, LM2901, LM2901E, LM2901V, NCV2901, MC3302
PACKAGE DIMENSIONS
TSSOP−14
CASE 948G
ISSUE B
14X K REF
0.10 (0.004)
0.15 (0.006) T U
M
T U
V
S
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL
IN EXCESS OF THE K DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
S
S
N
2X
14
L/2
0.25 (0.010)
8
M
B
−U−
L
PIN 1
IDENT.
F
7
1
0.15 (0.006) T U
N
S
DETAIL E
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
ÇÇÇ
ÉÉÉ
K
A
−V−
K1
J J1
SECTION N−N
−W−
C
0.10 (0.004)
−T− SEATING
PLANE
D
G
H
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
DETAIL E
MILLIMETERS
INCHES
MIN
MAX
MIN MAX
4.90
5.10 0.193 0.200
4.30
4.50 0.169 0.177
−−−
1.20
−−− 0.047
0.05
0.15 0.002 0.006
0.50
0.75 0.020 0.030
0.65 BSC
0.026 BSC
0.50
0.60 0.020 0.024
0.09
0.20 0.004 0.008
0.09
0.16 0.004 0.006
0.19
0.30 0.007 0.012
0.19
0.25 0.007 0.010
6.40 BSC
0.252 BSC
0_
8_
0_
8_
SOLDERING FOOTPRINT
7.06
1
0.65
PITCH
14X
0.36
14X
1.26
DIMENSIONS: MILLIMETERS
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
11
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
LM339/D