NCP5006

NCP5006
Compact Backlight LED
Boost Driver
The NCP5006 is a high efficiency boost converter operating in
current loop, based on a PFM mode, to drive White LED. The current
mode regulation allows a uniform brightness of the LEDs. The chip
has been optimized for small ceramic capacitors, capable to supply
up to 1.0 W output power.
http://onsemi.com
MARKING
DIAGRAM
Features
• 2.7 to 5.5 V Input Voltage Range
• Vout to 24 V Output Compliance Allows up to 5 LEDs Drive in
•
•
•
•
•
•
•
•
•
•
•
Series
Built−in Overvoltage Protection
Inductor Based Converter brings up to 90% Efficiency
Constant Output Current Regulation
0.3 mA Standby Quiescent Current
Includes Dimming Function (PWM)
Enable Function Driven Directly from Low Battery Voltage Source
Automatic LEDs Current Matching
Thermal Shutdown Protection
All Pins are Fully ESD Protected
Low EMI Radiation
Pb−Free Package is Available
Typical Applications
5
TSOP−5
SN SUFFIX
CASE 483
5
1
DCSAYWG
G
1
DCS
A
Y
W
G
= Device Code
= Assembly Location
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
PIN CONNECTIONS
Vout
1
GND
2
FB
3
• LED Display Back Light Control
• Keyboard Back Light
• High Efficiency Step Up Converter
5
Vbat
4
EN
(Top View)
ORDERING INFORMATION
Device
Package
Shipping†
NCP5006SNT1
TSOP−5
3000 Tape & Reel
NCP5006SNT1G
TSOP−5
(Pb−Free)
3000 Tape & Reel
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
© Semiconductor Components Industries, LLC, 2006
March, 2006 − Rev. 2
1
Publication Order Number:
NCP5006/D
NCP5006
Vbat
Vbat
U1
4
EN
Vbat
C1
5
4.7 mF
L1
22 mH
2
GND
GND
GND
D1
1
Vout
3
FB
MBR0530
NCP5006
R1
D6
C2
1.0 mF
D5
D4
D3
D2
GND
15 W
GND
LWT67C LWT67C LWT67C
LWT67C LWT67C
Figure 1. Typical Application
Thermal Shutdown
Current Sense
Vbat
5 Vbat
CONTROLLER
Vsense
EN 4
100 k
1 Vout
Q1
GND
FB 3
300 k
−
+
2 GND
GND
+200 mV
Band Gap
Figure 2. Block Diagram
http://onsemi.com
2
NCP5006
PIN FUNCTION DESCRIPTION
Pin
Pin Name
Type
Description
1
Vout
POWER
This pin is the power side of the external inductor and must be connected to the
external Schottky diode. It provides the output current to the load. Since the boost
converter operates in a current loop mode, the output voltage can range up to
+24 V but shall not extend this limit. However, if the voltage on this pin is higher
than the Over Voltage Protection threshold (OVP) the device comes back to
shutdown mode. To restart the chip, one must either send a Low to High
sequence on Pin EN, or switch off the Vbat supply. A capacitor must be used on
the output voltage to avoid false triggering of the OVP circuit. This capacitor
should be 1.0 mF minimum. Ceramic type, (ESR <100 mW), is mandatory to
achieve the high end efficiency. This capacitor limits the noise created by the fast
transients present in this circuitry. In order to limit the inrush current and to
operate with an acceptable start−up time, it is recommended to use any value
between 1.0 mF and 8.2 mF capacitor maximum. Care must be observed to avoid
EMI through the PCB copper tracks connected to this pin.
2
GND
POWER
This pin is the system ground for the NCP5006 and carries both the power and
the analog signals. High quality ground must be provided to avoid spikes and/or
uncontrolled operation. Care must be observed to avoid high−density current flow
in a limited PCB copper track. Ground plane technique is recommended.
3
FB
ANALOG INPUT
This pin provides the output current range adjustment by means of a sense
resistor connected to the analog control or with a PWM control. The dimming
function can be achieved by applying a PWM voltage technique to this pin (see
Figure 29). The current output tolerance depends upon the accuracy of this
resistor. Using a "5% metal film resistor or better, yields a good enough output
current accuracy.
Note: A built−in comparator switch OFF the DC/DC converter if the voltage
sensed across this pin and ground is higher than 700 mV (typical).
4
EN
DIGITAL INPUT
This is an Active−High logic input which enables the boost converter. The built−in
pull down resistor disables the device when the EN pin is left open. The LED
brightness can be controlled by applying a pulse width modulated signal to the
enable pin (see Figure 31).
5
Vbat
POWER
The external voltage supply is connected to this pin. A high quality reservoir
capacitor must be connected across Pin 1 and Ground to achieve the specified
output voltage parameters. A 4.7 mF/6.3 V, low ESR capacitor must be connected
as close as possible across Pin 5 and ground Pin 2. The X5R or X7R ceramic
MURATA types are recommended. The return side of the external inductor shall
be connected to this pin. Typical application will use a 22 mH, size 1008, to handle
the 1.0 to 100 mA max output current range. On the other hand, when the desired
output current is above 20 mA, the inductor shall have an ESR < 1.5 W to achieve
a good efficiency over the Vbat range.
http://onsemi.com
3
NCP5006
MAXIMUM RATINGS
Symbol
Value
Unit
Power Supply
Rating
Vbat
6.0
V
Output Power Supply Voltage Compliance
Vout
28
V
Digital Input Voltage
Digital Input Current
EN
−0.3 < Vin < Vbat + 0.3
1.0
V
mA
2.0
200
kV
V
PD
RqJA
160
250
mW
°C/W
Operating Ambient Temperature Range
TA
−25 to +85
°C
Operating Junction Temperature Range
TJ
−25 to +125
°C
TJmax
+150
°C
Tstg
−65 to +150
°C
ESD Capability (Note 1)
Human Body Model (HBM)
Machine Model (MM)
VESD
TSOP−5 Package
Power Dissipation @ TA = +85°C (Note 2)
Thermal Resistance, Junction−to−Air
Maximum Junction Temperature
Storage Temperature Range
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model (HBM) "2.0 kV per JEDEC standard: JESD22−A114
Machine Model (MM) "200 V per JEDEC standard: JESD22−A115
2. The maximum package power dissipation limit must not be exceeded.
3. Latch−up current maximum rating: "100 mA per JEDEC standard: JESD78.
4. Moisture Sensivity Level (MSL): 1 per IPC/JEDEC standard: J−STD−020A.
POWER SUPPLY SECTION (Typical values are referenced to TA = +25°C, Min & Max values are referenced −25°C to +85°C ambient
temperature, unless otherwise noted.)
Rating
Pin
Symbol
Min
Typ
Max
Unit
Power Supply
4
Vbat
2.7
−
5.5
V
Output Load Voltage Compliance
5
Vout
21
24
−
V
Continuous DC Current in the Load @ Vout = 3xLED, L = 22 mH,
ESR < 1.5 W, Vbat = 3.60 V
5
Iout
50
−
−
mA
Stand By Current, @ Iout = 0 mA, EN = L, Vbat = 3.6 V
4
Istdb
−
0.3
−
mA
Stand By Current, @ Iout = 0 mA, EN = L, Vbat = 5.5 V
4
Istdb
−
0.8
3.0
mA
Inductor Discharging Time @ Vbat = 3.6 V, L = 22 mH, 3xLED,
Iout = 10 mA
4
Toffmax
−
320
−
ns
Thermal Shutdown Protection
−
TSD
−
160
−
°C
Thermal Shutdown Protection Hysteresis
−
TSDH
−
30
−
°C
http://onsemi.com
4
NCP5006
ANALOG SECTION (Typical values are referenced to TA = +25°C, Min & Max values are referenced −25°C to +85°C ambient
temperature, unless otherwise noted.)
Pin
Symbol
Min
Typ
Max
Unit
High Level Input Voltage
Low Level Input Voltage
4
EN
1.3
−
−
−
−
0.4
V
V
EN Pull Down Resistor
4
REN
−
100
−
kW
Feedback Voltage Threshold
3
FB
185
200
225
mV
Output Current Stabilization Time Delay following a DC/DC Start−up,
@ Vbat = 3.60 V, L = 22 mH, Iout = 20 mA
1
Ioutdly
−
100
−
ms
Internal Switch ON Resistor @ Tamb = +25°C
1
QRDSON
−
1.7
−
W
Rating
5. The overall tolerance depends upon the accuracy of the external resistor.
ESD PROTECTION
The NCP5006 includes silicon devices to protect the pins
against the ESD spikes voltages. To cope with the different
ESD voltages developed in the applications, the built−in
structures have been designed to handle "2.0 kVin Human
Body Model (HBM) and "200 V in Machine Model (MM)
on each pin.
means of a current loop, the output voltage will varies
depending upon the dynamic impedance presented by the
load.
Considering high intensity LED, the output voltage can
range from a low 6.40 V (two LED in series biased with a
low current), up to 21 V, the voltage compliance the chip
can sustain continuously.
The basic DC/DC structure is depicted in Figure 3. With
a 28 V maximum rating voltage capability, the power
device can accommodate high voltage source without any
leakage current downgrading.
DC/DC OPERATION
The DC/DC converter is designed to supply a constant
current to the external load, the circuit being powered from
a standard battery supply. Since the regulation is made by
Vbat
L1
22 mH
Vdsense
POR
1
D1
Vds
GND
C1
RESET
LOGIC
CONTROL
Vdsense
GND
+
−
D4
ZERO_CROSSING
D5
1.0 mF
TIME_OUT
D3
D2
Q1
R1
−
V(Ipeak)
3
+
R2
xR
C2
Vref
GND
Figure 3. Basic DC/DC Converter Structure
http://onsemi.com
5
GND
Vs
NCP5006
Basically, the chip operates with two cycles:
Cycle #1: time t1, the energy is stored into the inductor
Cycle #2: time t2, the energy is dumped to the load
The POR signal sets the flip−flop and the first cycle takes
place. When the current hits the peak value, defined by the
First Start−Up
error amplifier associated to the loop regulation, the
flip−flop resets, the NMOS is deactivated and the current
is dumped into the load. Since the timings depend on the
environment, the internal timer limits the toff cycle to
320 ns (typical), making sure the system operates in a
continuous mode to maximize the energy transfer.
Normal Operation
Ipeak
IL
Iv
t1
0 mA
t2
t
Ids
0 mA
t
Io
0 mA
t
Figure 4. Basic DC−DC Operation
Based on the data sheet, the current flowing into the
inductor is bounded by two limits:
• Ipeak Value: Internally fixed to 350 mA typical
• Iv Value: Limited by the fixed Toff time built in the
chip (320 ns typical)
The system operates in a continuous mode as depicted in
Figure 4 and t1 and t2 times can be derived from basic
equations. (Note: The equations are for theoretical analysis
only, they do not include the losses.)
L + E * dI
dt
to avoid saturation of the core. On top of that, the ferrite
material shall be capable to operate at high frequency
(1.0 MHz) to minimize the Foucault’s losses developed
during the cycles.
The operating frequency can be derived from the
electrical parameters. Let V = Vo − Vbat, rearranging
Equation 1:
ton + dI * L
E
Since toff is nearly constant (according to the 320 ns
typical time), the dI is constant for a given load and
inductance value. Rearranging Equation 5 yields:
(eq. 1)
Let Vbat = E, then:
t1 +
(Ip * Iv) * L
Vbat
(Ip * Iv) * L
t2 +
Vo * Vbat
ton +
(eq. 2)
V*dt
L
*L
E
(eq. 6)
Let E = Vbat, and Vopk = output peak voltage, then:
(eq. 3)
ton +
Since t2 = 320 ns typical and Vo = 21 V maximum, then
(assuming a typical Vbat = 3.0 V):
DI +
(eq. 5)
(Vopk * Vbat) * dt
Vbat
(eq. 7)
Finally, the operating frequency is:
t2 * (Vo * Vbat)
L
f+
1
ton ) toff
(eq. 8)
The output power supplied by the NCP5006 is limited to
one watt: Figure 5 shows the maximum power that can be
delivered by the chip as a function of the output voltage.
(eq. 4)
320 ns * (21−3.0)
DImax +
+ 261 mA
22 mH
Of course, from a practical stand point, the inductor must
be sized to cope with the peak current present in the circuit
http://onsemi.com
6
NCP5006
Pout = f(Vbat) @ Rs = 2.0 W
Ipeak = f(Vbat) @ Lout = 22 mH
400
1200
3 LED
1000
350
2 LED
Ipeak (mA)
4 LED
5 LED
600
300
250
400
200
200
Pout = f(Vbat) @ Rsense = 2.0 W
0
150
2
3
4
Vbat (V)
5
2
6
3
4
Vbat (V)
5
6
Test conditions: L = 22 mH, Rsense = 10 W, Tamb = +20°C
Figure 5. Maximum Output Power as a Function of
the Battery Supply Voltage
Figure 6. Typical Inductor Peak Current as a
Function of Vbat Voltage
120
2 LED
100
3 LED
80
Iout (mA)
Pout (mW)
800
4 LED
60
5 LED
40
20
0
2.5
3.0
3.5
4.0
Vbat (V)
4.5
5.0
5.5
Test conditions: L = 22 mH, Rsense = 2.0 W, Tamb = +25°C
Figure 7. Maximum Output Current as a Function of Vbat
http://onsemi.com
7
NCP5006
Output Current Range Set−Up
The current regulation is achieved by means of an external sense resistor connected in series with the LED string.
Vbat
L1
22 mH
D1
FB
3
Load
Vout
1
Q1
CONTROLLER
GND
R1
xW
GND
Figure 8. Output Current Feedback
A standard 5% tolerance resistor, 22 W SMD device,
yields 9.09 mA, good enough to fulfill the back light
demand. The typical application schematic diagram is
provided in Figure 9.
The current flowing through the LED creates a voltage
drop across the sense resistor R1. The voltage drop is
constantly monitored internally, and maximum peak
current allowed in the inductor is set accordingly in order
to keep constant this voltage drop (and thus the current
flowing through the LED). For example, should one need
a 10 mA output current, the sense resistor should be sized
according to the following equation:
R1 + Feedback Threshold + 200 mV + 20 W
Iout
10 mA
(eq. 9)
Vbat
U1
4
Pulse
EN
Vbat
C1
5
4.7 mF
GND
L1
22 mH
GND
2
Vout
GND
FB
3
D1
1
MBR0530
NCP5006
R1
D6
D5
D4
D3
D2
GND
GND
22 W
C2
1.0 mF
LWT67C LWT67C LWT67C LWT67C LWT67C
Figure 9. Basic Schematic Diagram
http://onsemi.com
8
NCP5006
Output Load Drive
The Schottky diode D1, associated with capacitor C2
(see Figure 9), provides a rectification and filtering
function.
When a pulse−operating mode is acceptable:
• A PWM mode control can be used to adjust the output
current range by means of a resistor and a capacitor
connected across FB pin. On the other hand, the
Schottky diode can be removed and replaced by at
least one LED diode, keeping in mind such LED shall
sustain the large pulsed peak current during the
operation.
In order to optimize the built−in Boost capabilities, one
shall operate the NCP5006 in the continuous output current
mode. Such a mode is achieved by using and external
reservoir capacitor (see Table 1) across the LED.
At this point, the peak current flowing into the LED
diodes shall be within the maximum ratings specified for
these devices. Of course, pulsed operation can be achieved,
due to the EN signal Pin 4, to force high current into the
LED when necessary.
TYPICAL OPERATING CHARACTERISTICS
Yield = f(Vbat) @ Iout = 4.0 mA/Lout = 22 mH
Yield = f(Vbat) @ Iout = 10 mA/Lout = 22 mH
100
100
4 LED/4 mA
90
80
80
5 LED/4 mA
70
3 LED/4 mA
2 LED/4 mA
60
YIELD (%)
YIELD (%)
70
4 LED/10 mA
90
50
40
40
20
20
10
10
3.50
4.00
4.50
5.00
0
2.50
5.50
4.00
4.50
5.00
5.50
Figure 10. Overall Efficiency vs. Power Supply @
Iout = 4.0 mA, L = 22 mH
Figure 11. Overall Efficiency vs. Power Supply @
Iout = 10 mA, L = 22 mH
Yield = f(Vbat) @ Iout = 20 mA/Lout = 22 mH
100
3 LED/15 mA
90
80
80
70
5 LED/15 mA
2 LED/15 mA
YIELD (%)
70
YIELD (%)
3.50
Vbat (V)
90
60
3.00
Vbat (V)
Yield = f(Vbat) @ Iout = 15 mA/Lout = 22 mH
100
3 LED/10 mA
50
30
3.00
5 LED/10 mA
60
30
0
2.50
2 LED/10 mA
4 LED/15 mA
50
40
60
20
20
10
10
3.50
4.00
4.50
5.00
0
2.50
5.50
5 LED/20 mA
2 LED/20 mA
40
30
3.00
4 LED/20 mA
50
30
0
2.50
3 LED/20 mA
3.00
3.50
4.00
4.50
5.00
5.50
Vbat (V)
Vbat (V)
Figure 12. Overall Efficiency vs. Power Supply @
Iout = 15 mA, L = 22 mH
Figure 13. Overall Efficiency vs. Power Supply @
Iout = 20 mA, L = 22 mH
http://onsemi.com
9
NCP5006
Yield = f(Vbat) @ Iout = 40 mA/Lout = 22 mH
Feedback Variation vs. Temperature
100
205
2 LED/40 mA
204
FEEDBACK VOLTAGE (mV)
90
80
YIELD (%)
70
5 LED/40 mA
4 LED/40 mA
60
3 LED/40 mA
50
40
30
20
10
203
202
Vbat = 3.1 V thru 5.5 V
201
200
199
198
197
196
0
2.50
3.00
3.50
4.00
Vbat (V)
4.50
5.00
195
−40
5.50
0
−20
20
40
60
100
80
TEMPERATURE (°C)
All curve conditions: L = 22 mH, Cin = 4.7 mF, Cout = 1.0 mF,
Typical curve @ T° = +25°C
Figure 15. Feedback Voltage Stability
Figure 14. Overall Efficiency vs. Power Supply @
Iout = 40 mA, L = 22 mH
Feedback Variation vs. Nominal
(Vbat = 3.0 V, 6.0 V, T = 255C)
5
Standby Current vs. Vbat
1.4
−40°C thru 125°C
1.2
3
2
1.0
1
Vbat = 3.1 V thru 5.5 V
IStby (mA)
FEEDBACK VARIATION (%)
4
0
−1
−2
0.6
0.4
−3
0.2
−4
−5
−40
−20
0
20
40
60
80
0.0
2.7
100
3.3
4.5
Vbat (V)
Figure 16. Feedback Voltage Variation
Figure 17. Standby Current
Frequency = f(Vbat) @ Iout = 20 mA−Lout = 22 mH
5.1
5.5
OVP vs. Temperature
26
2 LED
2.0
1.5
3 LED
4 LED
1.0
5 LED
0.5
0
2.5
3.9
TEMPERATURE (°C)
OVERVOLTAGE PROTECTION (V)
2.5
f (mHz)
0.8
3.0
3.5
4.0
4.5
5.0
25
Vbat = 5.5 V
24
23
22
−40 −20
5.5
Vbat = 3.6 V
Vbat = 2.7 V
0
20
40
60
80
100
Vbat (V)
TEMPERATURE (°C)
Figure 18. Typical Operating Frequency
Figure 19. Overvoltage Protection
http://onsemi.com
10
120 130
NCP5006
TYPICAL OPERATING WAVEFORMS
Vout
Inductor
Current
Conditions: Vbat = 3.6 V, Lout = 22 mH, 5 LED, Iout = 15 mA
Figure 20. Typical Power Up Response
Vout
Inductor
Current
Conditions: Vbat = 3.6 V, Lout = 22 mH, 5 LED, Iout = 15 mA
Figure 21. Typical Start−Up Inductor Current and Output Voltage
http://onsemi.com
11
NCP5006
TYPICAL OPERATING WAVEFORMS
Inductor
Current
Conditions: Vbat = 3.6 V, Lout = 22 mH, 5 LED, Iout = 15 mA
Figure 22. Typical Inductor Current
Vout Ripple
50 mV/div
Inductor
Current
Conditions: Vbat = 3.6 V, Lout = 22 mH, 5 LED, Iout = 15 mA
Figure 23. Typical Output Voltage Ripple
http://onsemi.com
12
NCP5006
TYPICAL OPERATING WAVEFORMS
Output Voltage
Inductor Current
Test Conditions: L = 22 mH, Iout = 15 mA, Vbat = 3.6 V, Ambient Temperature
Figure 24. Typical Output Peak Voltage
92.00
EFFICIENCY (%)
90.00
ESR = 0.3 W
88.00
86.00
84.00
ESR = 1.3 W
82.00
80.00
78.00
3
3.5
4
4.5
5
5.5
Vbat (V)
NCP5006: Efficiency = f(ESR) @ 5 LED, ILed = 20 mA
Figure 25. Efficiency as a Function of Vbat and Inductor ESR
http://onsemi.com
13
NCP5006
NOISE (mV/SQR/Hz)
10.00
1.00
0.10
0.01
0.1
1
10
100
FREQUENCY (MHz)
Figure 26. Noise Returned to the Battery
Test Conditions: Vbat = 3.6 V, Iout = 20 mA, string of 3 LED (OSRAM LWT67C)
Figure 27. Relative EMI Over 100 kHz − 30 MHz Bandwidth
http://onsemi.com
14
1000
NCP5006
TYPICAL APPLICATIONS CIRCUITS
Standard Feedback
The standard feedback provides a constant current to the
LED, independently of the Vbat supply and number of LED
associated in series. Figure 28 depicts a typical application
to supply 13 mA to the load.
Vbat
Vbat
U1
4
C1
EN
Vbat
5
4.7 mF
L1
22 mH
GND
2
3
GND
GND
D1
Vout 1
FB
MBR0530
NCP5006
R1
D6
C2
1.0 mF
D5
D4
D3
D2
GND
15 W
GND
LWT67C LWT67C LWT67C LWT67C LWT67C
Figure 28. Basic DC Current Mode Operation with Analog Feedback
PWM Operation
start and stop the converter, yielding high transients . These
transients might generate spikes difficult to filter out in the
rest of the application, a situation not recommended. The
output current depends upon the duty cycle of the signal
presented to the node Pin 3: this is very similar to the digital
control discussed in Figure 31.
The average mode yields a noise free operation since the
converter operates continuously, together with a very good
dimming function. The cost is an extra resistor and one
extra capacitor, both being low cost parts.
The analog feedback Pin 3 provides a way to dim the
LED by means of an external PWM signal as depicted in
Figure 29. By optimizing the internal high impedance
presented by the FB pin, one can set up a simple R/C
network to accommodate such a dimming function. Two
modes of operation can be considered:
• Pulsed mode, with no filtering
• Averaged mode with filtering capacitor
Although the pulsed mode will provide a good dimming
function, from a human eye standpoint, it will continuously
http://onsemi.com
15
NCP5006
Vbat
Vbat
U1
4
C1
EN
Vbat
5
4.7 mF
L1
22 mH
Average Network
2
GND
R2
R3
150 k
10 k
3
PWM
C3
100 nF
GND
D1
Vout 1
FB
GND
MBR0530
NCP5006
C2
1.0 mF
R4
5.6 k
GND
GND
R1
D6
D5
D4
D3
D2
GND
10 W
LWT67C LWT67C LWT67C LWT67C LWT67C
NOTE: RC filter R2 and C3 is optional (see text)
Sense Resistor
Figure 29. Basic DC Current Mode Operation with PWM Control
value, preferably well below 1.0 MW. Consequently, let R2 =
150 k, R3 = 10 k and R4 = 5.6 k. On the other hand, the
feedback delay to control the luminosity of the LED shall be
acceptable by the user, 10 ms or less being a good
compromise. The time constant can now be calculated based
on a 400 mV offset voltage at the C3/R2/R3 node to force
zero current to the LED. Assuming the PWM signal comes
from a standard gate powered by a 3.0 V supply, running at
10 kHz, then a full dimming of the LED can be achieved with
a 95% span of the Duty Cycle signal. Figure 30 depicts the
behavior under such PWM analog mode.
To implement such a function, let consider the feedback
input as an operational amplifier with a high impedance
input (reference schematic Figure 29). The analog loop
will keep going to balance the current flowing through the
sense resistor R1 until the feedback voltage is 200 mV. An
extra resistor (R4) isolates the FB node from low resistance
to ground, making possible to add an external voltage to
this pin.
The time constant R2/C3 generates the voltage across C3,
added to the node Pin 1, while R2/R3/R4/R1/C3 create the
discharge time constant. In order to minimize the pick up
noise at FB node, the resistors shall have relative medium
PWM
VFB
VPWM
Figure 30. Operation with Analog PWM, f = 10 kHz, DC = 25%
http://onsemi.com
16
NCP5006
Digital Control
Cycle, but care must be observed as the DC/DC converter
is continuously pulsed ON/OFF and noise are likely to be
generated.
Due to the EN pin, a digitally controlled luminosity can
be implemented by providing a PWM signal to this pin (see
Figure 31). The output current depends upon the Duty
Vbat
U1
4
Pulse
EN
Vbat
C1
5
4.7 mF
L1
22 mH
GND
2
3
GND
GND
D1
Vout 1
FB
MBR0530
NCP5006
R1
GND
22 W
D6
C2
1.0 mF
D5
D4
D3
D2
GND
LWT67C LWT67C LWT67C LWT67C LWT67C
NOTE: Pulse width and frequency depends upon the application constraints.
Figure 31. Typical Semi−Pulsed Mode of Operation
The PWM operation, using the EN pin as a digital
control, is depicted in Figures 32 and 33. The tests have
been carried out at room temperature with Vbat = 3.60 V,
L = 22 mH, five LEDs in series, RFB = 22 W.
PWM
Vout
VFB
VPWM
Figure 32. Operation @ PWM = 10 kHz, DC = 10%
http://onsemi.com
17
NCP5006
PWM
Vout
VFB
PWR CLK
Figure 33. Operation @ PWM = 10 kHz, DC = 25%
PWM
Vout
PWR CLK
Figure 34. Magnified View of Operation @ PWM = 10 kHz, DC = 25%
http://onsemi.com
18
NCP5006
NCP5006 Iout = f(PWM) @ f = 10 kHz
10.00
9.00
8.00
Digital EN
Iout (mA)
7.00
Analog PWM
6.00
5.00
4.00
3.00
2.00
1.00
0.00
0
20
40
60
80
100
120
DC (%)
Figure 35. Output Current as a Function of the Operating Condition
Table 1. Recommended Passive Parts
Part
Manufacturer
Description
Part Number
Ceramic Capacitor 1.0 mF/16 V
MURATA
GRM42 − X7R
GRM42−6X7R−105K16
Ceramic Capacitor 1.0 mF/25 V
MURATA
GRM42 – X5R
GRM
Ceramic Capacitor 4.7 mF/6.3 V
MURATA
GRM40 – X5R
GRM40−X5R−475K6.3
Inductor 22 mH
CoilCraft
1008PS − Shielded
1008PS−223MC
Inductor 22 mH
CoilCraft
Power Wafer
LPQ4812−223KXC
Inductor 22 mH
WURTH
Power Choke
744031220
Inductor 22 mH
TDK
Power Inductor
VLP4614T−220MR40
http://onsemi.com
19
NCP5006
Typical LEDs Load Mapping
Since the output power is voltage battery limited (see
Figure 5), one shall arrange the LED to cope with a specific
need. In particular, since the power cannot extend 600 mW
under realistic battery supply, powering ten LED can be
achieved by a series/parallel combination as depicted in
Figure 36.
50 mA
75 mA
D1
LED
D5
LED
D2
LED
D6
LED
D3
LED
D7
LED
D4
LED
D8
LED
7.0 V (Typ.)
Load
14 V (Typ.)
Load
D1
LED
D3
LED
D5
LED
D7
LED
D9
LED
D2
LED
D4
LED
D6
LED
D8
LED
D10
LED
Sense
Resistor
R1
2.7 W
GND
60 mA
R1
3.9 W
Load
10.5 V (Typ.)
Sense
Resistor
GND
Test conditions: Vbat = 3.6 V
Lout = 22 mH
Cout = 1.0 mF
D1
LED
D4
LED
D7
LED
D10
LED
D13
LED
D2
LED
D5
LED
D8
LED
D11
LED
D14
LED
D3
LED
D6
LED
D9
LED
D12
LED
D15
LED
Sense
Resistor
R1
3.3 W
GND
Figure 36. Examples of Possible LED Arrangements
http://onsemi.com
20
NCP5006
GND
C2
4.7 mF/
16 V
MMBF0201NLT1
C3
4.7 mF/
16 V
D9
D10
D11
R7
Q2
3.3 R
GND
LWT67C LWT67C LWT67C
TP?
R6
Vout
D5
D6
D7
D8
D12
Q1
51 R
MMBF0201NLT1
GND
Adjust Flash Pulse Width
1.0 mF/
10 V
GND
D2
HC132
9 U2C
1N4148
D4
10 k
R2
10 k
R1
C1
8
VCC
GND
10
NCP5006
4.7 mF/6.0 V
10 k
500 kA
3
EN
TRA
TRB
CLR
GND VCC
C9
P2
Vbat
CTC
R4
VCC
5
1
2
3
NLAS4599
2
GND
15
Vout
22 mH
4
L1
4
1
14
VFB
U1
U4A
M54HC123
RCCOM
6
5
FB
4
Q
U5
1
TP1
Q
MBR0530
13
LWT67C LWT67C LWT67C LWT67C LWT67C
SNJ54HC132
HC132
13
12
D3
U2D
1.0 nF
11
1N4148
C7
GND
VCC
C6
C8
10 mF/
10 V
100 k
3
2
S2
1
D1
VCC
SINGLE/REPEAT
SNJ54HC132
HC132
1
R8
1.5 k
R5
GND
S1
2
1
J2
Vbat
REPEAT
D13
SNJ54HC132
HC132
5
4
10 k
GND
MBR0530
VCC
GND
R3
2
4.7 mF/
16 V
P1
100 kA
3
C4
U2A
Adjust Flash Duty Cycle
100 nF
U2B
C5
GND
6
100 nF
GND
J1
ENABLE
TRIG
Figure 37. NCP5006 Demo Board Schematic Diagram
http://onsemi.com
21
VCC
GND
NCP5006
Figure 38. NCP5006 Demo Board PCB: Top Layer
Figure 39. NCP5006 Demo Board PCB: Bottom Layer
Figure 40. NCP5006 Demo Board Top Silkscreen
http://onsemi.com
22
NCP5006
FIGURES INDEX
Figure 1:
Figure 2:
Figure 3:
Figure 4:
Figure 5:
Figure 6:
Figure 7:
Figure 8:
Figure 9:
Figure 10:
Figure 11:
Figure 12:
Figure 13:
Figure 14:
Figure 15:
Figure 16:
Figure 17:
Figure 18:
Figure 19:
Figure 20:
Figure 21:
Figure 22:
Figure 23:
Figure 24:
Figure 25:
Figure 26:
Figure 27:
Figure 28:
Figure 29:
Figure 30:
Figure 31:
Figure 32:
Figure 33:
Figure 34:
Figure 35:
Figure 36:
Figure 37:
Figure 38:
Figure 39:
Figure 40:
Typical Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Basic DC/DC Converter Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Basic DC/DC Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Maximum Output Power as a Function of the Battery Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Typical Inductor Peak Current as a Function of Vbat Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Maximum Output Current as a Function of Vbat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Output Current Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Basic Schematic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Overall Efficiency vs. Power Supply @ Iout = 4.0 mA, L = 22 mH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Overall Efficiency vs. Power Supply @ Iout = 10 mA, L = 22 mH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Overall Efficiency vs. Power Supply @ Iout = 15 mA, L = 22 mH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Overall Efficiency vs. Power Supply @ Iout = 20 mA, L = 22 mH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Overall Efficiency vs. Power Supply @ Iout = 40 mA, L = 22 mH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Feedback Voltage Stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Feedback Voltage Variation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Standby Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Typical Operating Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Overvoltage Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Typical Power Up Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Typical Start−Up Inductor Current and Output Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Typical Inductor Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Typical Output Voltage Ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Typical Output Peak Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Efficiency as a Function of Vbat and Inductor ESR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Noise Returned to the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Relative EMI Over 100 kHz−30 MHz Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Basic DC Current Mode Operation with Analog Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Basic DC Current Mode Operation with PWM Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Operation with Analog PWM, f = 10 kHz, DC = 25% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Typical Semi−Pulsed Mode of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Operation @ PWM = 10 kHz, DC = 10% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Operation @ PWM = 10 kHz, DC = 25% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Magnified View of Operation @ PWM = 10 kHz, DC = 25% . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Output Current as a Function of the Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Examples of Possible LED Arrangements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
NCP5006 Demo Board Schematic Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
NCP5006 Demo Board PCB: Top Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
NCP5006 Demo Board PCB: Bottom Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
NCP5006 Demo Board Top Silkscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
NOTE CAPTIONS INDEX
Note 1:
Note 2:
Note 3:
Note 4:
Note 5:
This device series contains ESD protection and exceeds the following tests . . . . . . . . . . . . . . . . . . . . . . . . .
The maximum package power dissipation limit must not be exceeded . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Latch−up current maximum rating: "100 mA per JEDEC standard: JESD78 . . . . . . . . . . . . . . . . . . . . . . . .
Moisture Sensivity Level (MSL): 1 per IPC/JEDEC standard: J−STD−020A . . . . . . . . . . . . . . . . . . . . . . . .
The overall tolerance depends upon the accuracy of the external resistor . . . . . . . . . . . . . . . . . . . . . . . . . . .
ABBREVIATIONS
EN
FB
POR
Enable
Feed Back
Power On Reset: Internal pulse to reset the chip when the power supply is applied
http://onsemi.com
23
4
4
4
4
5
NCP5006
PACKAGE DIMENSIONS
TSOP−5
SN SUFFIX
CASE 483−02
ISSUE C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. MAXIMUM LEAD THICKNESS INCLUDES
LEAD FINISH THICKNESS. MINIMUM LEAD
THICKNESS IS THE MINIMUM THICKNESS
OF BASE MATERIAL.
4. A AND B DIMENSIONS DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
D
S
5
4
1
2
3
B
L
MILLIMETERS
INCHES
DIM MIN
MAX
MIN
MAX
A
2.90
3.10 0.1142 0.1220
B
1.30
1.70 0.0512 0.0669
C
0.90
1.10 0.0354 0.0433
D
0.25
0.50 0.0098 0.0197
G
0.85
1.05 0.0335 0.0413
H 0.013 0.100 0.0005 0.0040
J
0.10
0.26 0.0040 0.0102
K
0.20
0.60 0.0079 0.0236
L
1.25
1.55 0.0493 0.0610
M
0_
10 _
0_
10 _
S
2.50
3.00 0.0985 0.1181
G
A
J
C
0.05 (0.002)
H
M
K
SOLDERING FOOTPRINT*
0.95
0.037
1.9
0.074
2.4
0.094
1.0
0.039
0.7
0.028
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any
liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over
time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under
its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees,
subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of
personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part.
SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
Literature Distribution Center for ON Semiconductor
USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada
Phone: 81−3−5773−3850
Email: [email protected]
http://onsemi.com
24
ON Semiconductor Website: http://onsemi.com
Order Literature: http://www.onsemi.com/litorder
For additional information, please contact your
local Sales Representative.
NCP5006/D