Ordering number : ENA1341B LV8413GP Bi-CMOS LSI For DSC, and Cell Phone Camera Modules H-Bridge × 2-channel Motor Driver http://onsemi.com Overview The LV8413GP is an H-bridge × 2-channel motor driver IC and is able to control 4 modes of forward, reverse, brake, and standby. This IC housed in a miniature package is optimum for use in a stepping motor driving system for DSC or a camera module of cell phones. Features • Saturation drive H-bridge : 2-channels • Built-in thermal protection circuit • Built-in low voltage malfunction prevention circuit • Incorporates a transistor for driving photosensors Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit Power supply voltage 1 VM max 6 Power supply voltage 2 VCC max 6 Output peak current IO peak Output continuous current 1 Output continuous current 2 V V Outs 1 to 4, t ≤ 10msec, ON-duty ≤ 20% 600 IO max1 Outs 1 to 4 400 mA IO max2 PI 15 mA Allowable power dissipation Pd max Mounted on a circuit board* 0.7 W Operating temperature Topr -30 to +85 °C Storage temperature Tstg -55 to +150 °C mA * Specified circuit board : 50.0mm × 40.0mm × 0.8mm : glass epoxy four-layer board (2S2P) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Semiconductor Components Industries, LLC, 2013 June, 2013 62712 SY 20120613-S00001/51111 SY/N1908 MS PC 20081016-S00007 No.A1341-1/7 LV8413GP Recommended Operating Conditions at Ta = 25°C Parameter Symbol Conditions Ratings Unit Power supply voltage range 1 VM 2.5 to 5.5 Power supply voltage range 2 VCC 2.5 to 5.5 V Logic input voltage range VIN 0 to VCC+0.3 V Input frequency fIN IN1 to 4, INA to 100 V kHz Electrical Characteristics at Ta = 25°C, VM = 5V, VCC = 3.3V, unless otherwise specified. Parameter Symbol Ratings Conditions min typ Unit max Standby mode current drain Istn IN1 to 4 = “L” 1.0 μA VM current drain IM Any one of IN1 to 4 = “H”, with no load 70 150 μA VCC current drain ICC Any one of IN1 to 4 = “H” 0.6 1.2 mA VCC low-voltage cutoff voltage VthVCC 1.85 2.10 2.35 V Low-voltage hysteresis voltage VthHYS 100 150 200 mV Thermal shutdown temperature TSD Design guarantee value * 160 180 200 °C Thermal hysteresis width ΔTSD Design guarantee value * 10 30 50 °C Rin IN1 to 4 50 100 200 kΩ 33 OUT1 to 4 Logic pin internal pull-down resistance Logic pin input current Logic input high-level voltage IinL VIN = 0, IN1 to 4 IinH VIN = 3.3V, IN1 to 4 20 VinH IN1 to 4 2.5 1.0 μA 60 μA V Logic input low-level voltage VinL IN1 to 4 1.0 V Output on-resistance Ronu IO = 400mA, upper ON resistance 0.5 0.8 Ω Rond IO = 400mA, lower ON resistance 0.3 0.5 Ω 1 μA 1.0 Output leakage current IOleak Diode forward voltage VD ID = -400mA Rin INA Logic pin input current IinL VIN = 0, INA IinH VIN = 3.3V, INA 20 Logic input high-level voltage VinH INA 2.5 Logic input low-level voltage VinL INA Output on-resistance Ron IO = 10mA Output leakage current IOleak V PI Logic pin internal pull-down 50 100 200 kΩ 1.0 μA 50 μA resistance 33 V 1.0 4 V 6 Ω 1 μA No.A1341-2/7 LV8413GP Package Dimensions unit : mm (typ) 3318 TOP VIEW SIDE VIEW BOTTOM VIEW Allowable power dissipation, Pd max – W (0.13) 16 0.4 2.6 (C0.116) 2 1 0.5 LASER MARKED INDEX (0.55) (0.035) 0.8 SIDE VIEW 0.25 Pd max – Ta 0.8 (0.125) 2.6 Specified board : 50.0×40.0×0.8mm3 4-layer glass epoxy (2S2P) 0.7 0.6 0.4 0.36 0.2 0 – 30 0 30 60 90 120 Ambient temperature, Ta – °C SANYO : VCT16(2.6X2.6) 12 11 10 9 SGND VCC VM PGND Pin Assignment 13 PI OUT1 8 14 INA OUT2 7 OUT3 6 OUT4 5 LV8413GP 15 IN4 Top View IN1 VM PGND IN3 IN2 16 1 2 3 4 No.A1341-3/7 LV8413GP Block Diagram + VM VM OUT1 OUT2 OUT3 OUT4 PGND PGND Thermal shutdown circuit Logic circuit VCC + - LVS circuit 15mA max SGND IN1 IN2 IN3 IN4 INA PI VCC CPU No.A1341-4/7 LV8413GP Pin Functions Pin No. Pin name Pin Function 2 IN1 Control signal input pin 1 IN2 Control signal input pin 16 IN3 Control signal input pin 15 IN4 Control signal input pin 14 INA Control signal input pin Equivalent Circuit VCC 10kΩ 100kΩ GND 8 OUT1 Outpin 7 OUT2 Outpin 6 OUT3 Outpin 5 OUT4 Outpin VM PGND 13 PI Outpin GND 11 VCC Logic system power supply connection pin 3 VM Motor power supply connection pin 10 VM Motor power supply connection pin 12 SGND Signal ground 4 PGND Power ground 9 PGND Power ground No.A1341-5/7 LV8413GP Logic input specifications • Common channels 1 to 2 ch1 : IN1 to IN2, OUT1 to OUT2 ch2 : IN3 to IN4, OUT3 to OUT4 Input Output IN1 IN2 OUT1 OUT2 Operation mode L L OFF OFF Standby H L H L CW (forward) L H L H CCW (reverse) H H L L Brake • Output stage transistor function VM VM VM ON OFF OFF ON OFF OFF OFF ON ON OFF ON ON (Forward) (Reverse) (Brake) • Photo sensor driving transistor When thermal shutdown and VCC low-voltage cut circuits are activated, OUT1 through OUT4 are turned OFF under control of the internal circuit. But the output (PI) of photo sensor driving transistor continues operation. Input Photo sensor driving INA PI L OFF H ON No.A1341-6/7 LV8413GP ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A1341-7/7