LV5239TA Bi-CMOS LSI 24-channel LED Driver www.onsemi.com Overview The LV5239TA is a 24-channel LED driver IC that is capable of switching between constant-current output and open drain output. It enables 2-wire/3-wire serial bus control (address designation) to be set arbitrarily using an external pin. Also possible are 24-channel LED ON/OFF control and the setting of the PWM luminance in 256 steps. Up to 32 driver ICs can be connected using the slave address setting pins. TQFP48 EP 7x7, 0.5P Function 24-channel output constant-current LED driver/open drain output LED driver (selected by using an external pin). Supports separate ON/OFF setting for each LED output, high withstand voltage (VOUT<42V). In the constant-current mode (OUTSCT: L), the reference current is set by the value of resistor connected to the external pin (RT1). Built-in D/A (3 bits) for switching current level … 6.40mA to 32.40mA (RGB drive). Constant current (IO max=50mA) for full-color LEDs 24 channels. In the open drain mode (OUTSCT: H), high current drive (IO max=100mA) 24 channels In the constant-current mode (OUTSCT: M) Only RGB7, RGB8 is open drain (IO max=100mA) Luminance adjustment using internal PWM control (256 steps), It copes with independent PWM control for each LED output. 8-bit PWM luminance dimming (0% to 99.6%) 8-phase PWM Selection of 2-wire/ 3-wire serial bus control signals enabled (switching using an external pin). Schmitt trigger input (3.3V/5V) Slave addressing (5 bits, connection of up to 32 driver ICs possible) Input Power supply supports 12V Internal reference output terminal (5V) Low current consumption Output malfunction protection circuits (thermal protection function, UVLO detection protection function, Power on RESET) ORDERING INFORMATION See detailed ordering and shipping information on page 28 of this data sheet. © Semiconductor Components Industries, LLC, 2016 February 2016 - Rev. 0 1 Publication Order Number : LV5239TA/D LV5239TA Specifications Absolute Maximum Ratings at Ta = 25C Parameter Symbol Conditions Ratings VCC max Maximum supply voltage Unit 13.6 V VLED VLED 42 V VREF VREF 5.8 V LED off Output current VO max IO max Allowable power dissipation Pd max Ta 25C * 1.25 W Operating temperature Topr 25 to +85 C Storage temperature Tstg 40 to +150 C Output voltage Open drain 42 V 100 mA * Specified board: 114.3mm 76.1mm 1.6mm, glass epoxy board. Exposed Die-pad area is not a substrate mounting. [Warning] : If you should intend to use this IC continuously under high temperature, high current, high voltage, or drastic temperature change, even if it is used within the range of absolute maximum ratings or operating conditions, there is a possibility of decrease reliability. Please contact us for a confirmation. Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. Recommended Operating Conditions at Ta = 25C Parameter Operating supply voltage range Symbol Conditions VCC op SVCC VLED op VREF op Ratings Unit 3.0 to 12.8 V VLED 3.0 to 42 V VREF 3.0 to 5.5 V [Warning] : The VLED terminal becomes the terminal for protection of the LED drive output. Please be connected to the power supply same as LED drive. When IC power supply (SVCC) and power supply of the LED or two kinds of power supply is more than it, please connect VLED to the highest potential and the power supply that it is. Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. www.onsemi.com 2 LV5239TA Electrical Characteristics at Ta 25C, VCC = 5V (=VREF) Parameter Symbol Ratings Conditions min typ Unit max Consumption current ICC1 LED off 1.8 2.3 2.9 Reference current pin voltage VRT RT1=30k 1.14 1.22 1.30 MAX output current IL 10 Between bits output current IOL Maximum LED driver output current 1 IMAX1 LED output on resistance 1 Ron1 VO=0.7 to 4.0V(Same channel line regulation) IO=32.40mA (Between bits pairing characteristics) RT1=30k LED OUTSCT= L IO = 10mA OFF leak current Ileak LED OFF Power on RESET voltage VPOR The voltage that is canceled 30.0 mA V % 32.4 5 % 34.8 mA 10 20 10 A 2.5 V Reset voltage VRST UVLO voltage 2.3 V VREF voltage VREF VREF=open 4.9 V VREF voltage VREF1 VCC = 6.0V, IO = 10mA Oscillator frequency Fosc 4.7 5.1 5.4 1000 V kHz * Power on RESET Reset all the data in the IC at the time of power activation. And it becomes the default setting. * UVLO detection protection function When SVCC decreases, it turns off LED output terminal. * Thermal protection function When a temperature in the IC rises, it turns off output terminal. When temperature falls, it returns by oneself. Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. Control circuit at Ta 25C, VCC = 5.0V (=VREF) Parameter Symbol Conditions Ratings min typ max Unit H level 1 VH1 Input H level OUTSCT 4.5 5.0 M level 1 VM1 Input M level OUTSCT 1.8 3.0 V V L level 1 VL1 Input L level OUTSCT 0.2 0.5 V V H level 2 VH2 Input H level CTLSCT 3.5 5.0 L level 2 VL2 Input L level CTLSCT 0.2 0.5 V H level 3 VH3 Input H level RESET 4.0 5.0 V L level 3 VL3 Input L level RESET 0.2 1.0 V H level 4 VH4 Input H level SCLK, SDATA, SDEN 4.0 5.0 V L level 4 VL4 Input L level SCLK, SDATA, SDEN 0.2 1.0 V H level 5 VH5 Input H level A0 to A4 3.5 5.0 V L level 5 VL5 Input L level A0 to A4 0.2 0.5 V www.onsemi.com 3 LV5239TA Electrical Characteristics at Ta 25C, VCC = 3.3V (=VREF) Parameter Symbol Conditions Ratings min Consumption current ICC1 LED off Reference current pin voltage VRT RT1=30k 1.14 MAX output current IL VO=0.7 to 4.0V(Same channel line regulation) 10 Between bits output current IOL IO=32.40mA (Between bits pairing typ Unit max 2.1 1.22 mA 1.30 V % 5 % characteristics) Maximum LED driver output IMAX1 current 1 RT1=30k 32.4 mA LED OUTSCT= L 10 20 10 A LED output on resistance 1 Ron1 IO = 10mA OFF leak current Ileak LED OFF Power on RESET voltage VPOR The voltage that is canceled 2.5 V Reset voltage VRST UVLO voltage 2.3 V VREF voltage VREF VREF=open Oscillator frequency Fosc 3.2 V 1000 kHz Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. Control circuit at Ta 25C, VCC = 3.3V (=VREF) Parameter Symbol Conditions Ratings min typ max Unit H level 1 VH1 Input H level OUTSCT 2.8 3.3 M level 1 VM1 Input M level OUTSCT 1.2 1.7 V V L level 1 VL1 Input L level OUTSCT 0.2 0.5 V V H level 2 VH2 Input H level CTLSCT 2.3 3.3 L level 2 VL2 Input L level CTLSCT 0.2 0.5 V H level 3 VH3 Input H level RESET 2.7 3.3 V L level 3 VL3 Input L level RESET 0.2 0.6 V H level 4 VH4 Input H level SCLK, SDATA, SDEN 2.7 3.3 V L level 4 VL4 Input L level SCLK, SDATA, SDEN 0.2 0.6 V H level 5 VH5 Input H level A0 to A4 2.3 3.3 V L level 5 VL5 Input L level A0 to A4 0.2 0.5 V www.onsemi.com 4 LV5239TA Package Dimensions unit : mm TQFP48 EP 7x7, 0.5P CASE 932F ISSUE C 4X 12 TIPS NOTES: 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. DAMBAR PROTRUSION SHALL BE 0.08 MAX. AT MMC. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OF THE FOOT. MINIMUM SPACE BETWEEN PROTRUSION AND ADJACENT LEAD IS 0.07. 0.20 C A-B D NOTE 9 D NOTE 7 D 25 SIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.25 PER SIDE. DIMENSIONS D1 AND E1 ARE MAXIMUM PLASTIC BODY SIZE INCLUDING MOLD MISMATCH. 5. THE TOP PACKAGE BODY SIZE MAY BE SMALLER THAN THE BOTTOM PACKAGE SIZE BY AS MUCH AS 0.15. 6. DATUMS A-B AND D ARE DETERMINED AT DATUM PLANE H. 7. A1 IS DEFINED AS THE VERTICAL DISTANCE FROM THE SEATING 37 NOTE 7 NOTE 7 A NOTES 4&6 B NOTE 9 E1 E 8. DIMENSIONS D AND E TO BE DETERMINED AT DATUM PLANE C. 13 48 DIM A A1 A2 b D D1 D2 E E1 E2 e L L2 M 1 D1 4X NOTES 4 & 6 0.20 H A-B D TOP VIEW DETAIL A 0.08 C A H 0.05 L2 A2 A1 e 48X SIDE VIEW C SEATING PLANE DETAIL A b 0.20 C A-B D M L MILLIMETERS MIN MAX 0.95 1.25 0.05 0.15 0.90 1.20 0.17 0.27 9.00 BSC 7.00 BSC 4.90 5.10 9.00 BSC 7.00 BSC 4.90 5.10 0.50 BSC 0.45 0.75 0.25 BSC 0° 7° GENERIC MARKING DIAGRAM* NOTE 3 D2 XXXXXXXXXX XXXXXXXXXX AWLYYWWG RECOMMENDED SOLDERING FOOTPRINT* 9.36 E2 1.13 5.30 BOTTOM VIEW 1 48X XXXXX A WL YY WW G = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week = Pb Free Package 9.36 *This information is generic. Please refer to device data sheet for actual part marking. 5.30 1 48X 0.29 0.50 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 5 LV5239TA LEDG6 LEDB6 LEDR7 LEDG7 LEDB7 PGND4 LEDR8 LEDG8 LEDB8 TEST1 TEST2 SVCC Block Diagram LEDG3 LEDR3 LEDB2 LEDG2 LEDR2 PGND1 LEDB1 LEDG1 LEDR1 A4 A3 A2 [Warning] : The VLED terminal becomes the terminal for protection of the LED drive output. Please be connected to the power supply same as LED drive. When IC power supply (SVCC) and power supply of the LED or two kinds of power supply is more than it, please connect VLED to the highest potential and the power supply that it is. www.onsemi.com 6 PGND3 LEDB5 LEDG5 LEDR5 NC VLED LEDB4 LEDG4 LEDR4 PGND2 LEDB3 Pin Assignment LEDR6 LV5239TA 36 35 34 33 32 31 30 29 28 27 26 25 LEDG6 37 24 LEDG3 LEDB6 38 23 LEDR3 LEDR7 39 22 LEDB2 LEDG7 40 21 LEDG2 LEDB7 41 20 LEDR2 PGND4 42 19 PGND1 LEDR8 43 18 LEDB1 LEDG8 44 17 LEDG1 LEDB8 45 16 LEDR1 TEST1 46 15 A4 TEST2 47 14 A3 SVCC 48 13 A2 6 7 8 9 SDEN CTLSCT OUTSCT RESET RT1 NC 10 11 12 A1 5 A0 4 SGND 3 SDATA VREF 2 SCLK 1 Pin Descriptions Pin No. Pin name I/O Description 1 VREF O 5V reference output pin 2 SCLK I Serial clock signal input pin 3 SDATA I Serial data signal input pin 4 SDEN I Serial enable signal input pin 5 CTLSCT I 2-wire serial bus/3-wire serial bus selecting control pin (L: 3-wire serial, H: 2-wire serial) 6 OUTSCT I Output type switching control pin L: Constant-current output M:Constant output, only RGB7,RGB8 is open drain output H: Open drain output 7 RESET I Reset signal input pin 8 RT1 O LED current setting resistor connection pin 9 NC Analog circuit GND pin No connection 10 SGND - 11 A0 I Slave address input pin A0 12 A1 I Slave address input pin A1 13 A2 I Slave address input pin A2 14 A3 I Slave address input pin A3 15 A4 I Slave address input pin A4 16 LEDR1 O LEDR1 output pin 17 LEDG1 O LEDG1 output pin 18 LEDB1 O LEDB1 output pin 19 PGND1 - GND pin dedicated for LED driver 20 LEDR2 O LEDR2 output pin 21 LEDG2 O LEDG2 output pin 22 LEDB2 O LEDB2 output pin 23 LEDR3 O LEDR3 output pin 24 LEDG3 O LEDG3 output pin 25 LEDB3 O LEDB3 output pin Continued on next page. www.onsemi.com 7 LV5239TA Continued from preceding page. Pin No. Pin name I/O Description 26 PGND2 - GND pin dedicated for LED driver 27 LEDR4 O LEDR4 output pin 28 LEDG4 O LEDG4 output pin 29 LEDB4 O LEDB4 output pin 30 VLED Output protection pin 31 NC No connection 32 LEDR5 O LEDR5 output pin 33 LEDG5 O LEDG5 output pin 34 LEDB5 O LEDB5 output pin 35 PGND3 - GND pin dedicated for LED driver 36 LEDR6 O LEDR6 output pin 37 LEDG6 O LEDG6 output pin 38 LEDB6 O LEDB6 output pin 39 LEDR7 O LEDR7 output pin 40 LEDG7 O LEDG7 output pin 41 LEDB7 O LEDB7 output pin 42 PGND4 - GND pin dedicated for LED driver 43 LEDR8 O LEDR8 output pin 44 LEDG8 O LEDG8 output pin 45 LEDB8 O LEDB8 output pin 46 TEST1 I Test1 pin (connected to GND) 47 TEST2 I Test2 pin (connected to GND) 48 SVCC - Power supply pin OUTSCT Settings LED Driver Output Pin OUTSCT pin LED1, LED2, LED3, LED4, LED5, LED6 LED7,LED8 L=-0.2 to 0.3V Constant current output Constant current output Built-in current value switching D/A (3 bits) Built-in current value switching D/A (3 bits) 6.40mA to 32.40mA, RT1=30kΩ (f=1MHz) 6.40mA to 32.40mA, RT1=30kΩ (f=1MHz) H=4.7 to 5.0V M=1.8 to 3.0V Open drain output Open drain output Current value is determined by external limiting resistor. Current value is determined by external limiting resistor. RON=10Ω RON=10Ω Constant current output Open drain output Built-in current value switching D/A (3 bits) Current value is determined by external limiting resistor. 6.40mA to 32.40mA, RT1=30kΩ (f=1MHz) RON=10Ω Power on RESET Settings www.onsemi.com 8 LV5239TA Pin Functions Pin No. Pin Name Pin function 48 SVCC Power supply pin 1 VREF Reference output pin(5V) 2 SCLK Serial clock signal input pin 3 SDATA Serial data signal input pin 4 SDEN Serial enable signal input pin Equivalent Circuit SCLK SDATA SDEN 5kΩ 100kΩ 5 CTLSCT Serial bus communication setting pin When set to low: The 3-wire serial bus signals are set as the input signals. When set to high: The 2-wire serial bus signals are set as the input signals. 6 OUTSCT LED driver output type setting pin When set to low: Constant-current output is set for the LED driver. When set to high: Open drain output is set for the LED driver. When set to middle: Constant-current output is set for the LED driver. However, open drain output is set for the only LED7 driver and LED8 driver. 7 RESET Reset signal input pin Reset status when set to low. 8 RT1 Reference current setting resistor connection pin. By connecting the external register between this pin and GND, the reference current is generated. The pin voltage is approximately 1.22V. By changing the current level, it is possible to change the oscillator frequency and LED driver current value (in the constant-current mode). 9 NC No connection 10 SGND GND pin Continued on next page. www.onsemi.com 9 LV5239TA Continued from preceding page. Pin No. Pin Name Pin function 11 A0 Slave address setting pin A0 12 A1 Slave address setting pin A1 13 A2 Slave address setting pin A2 14 A3 Slave address setting pin A3 15 A4 Slave address setting pin A4 16 LEDR1 LEDR1 output pin 17 LEDG1 LEDG1 output pin 18 LEDB1 LEDB1 output pin 20 LEDR2 LEDR2 output pin 21 LEDG2 LEDG2 output pin 22 LEDB2 LEDB2 output pin 23 LEDR3 LEDR3 output pin 24 LEDG3 LEDG3 output pin 25 LEDB3 LEDB3 output pin 27 LEDR4 LEDR4 output pin 28 LEDG4 LEDG4 output pin 29 LEDB4 LEDB4 output pin 32 LEDR5 LEDR5 output pin 33 LEDG5 LEDG5 output pin 34 LEDB5 LEDB5 output pin 36 LEDR6 LEDR6 output pin 37 LEDG6 LEDG6 output pin 38 LEDB6 LEDB6 output pin 39 LEDR7 LEDR7 output pin 40 LEDG7 LEDG7 output pin 41 LEDB7 LEDB7 output pin 43 LEDR8 LEDR8 output pin 44 LEDG8 LEDG8 output pin 45 LEDB8 LEDB8 output pin Equivalent Circuit If these pins are not going to be used, they must always be connected to GND. 30 VLED Output protection pin 31 NC No connection 19 PGND1 GND pin dedicate for LED output 26 PGND2 GND pin dedicate for LED output 35 PGND3 GND pin dedicate for LED output 42 PGND4 GND pin dedicate for LED output 46 TEST1 Test1 pin This pin must always be connected to GND. TEST1 10kΩ 60kΩ 47 TEST2 Test2 pin This pin must always be connected to GND. www.onsemi.com 10 LV5239TA Serial Bus Communication Specifications 1) Serial bus transfer timing conditions Parameter Symbol Conditions Min. Typ. Max. Unit Cycle time tcy1 SCLK clock period 200 - - ns Data setup time ts0 SDEN setup time relative to the rise of SCLK 90 - - ns ts1 SDATA setup time relative to the rise of SCLK 60 - - ns th0 SDEN hold time relative to the fall of SCLK 200 - - ns th1 SDATA hold time relative to the fall of SCLK 60 - - ns Data hold time Pulse width tw1L Low period pulse width of SCLK 90 - - ns tw1H High period pulse width of SCLK 90 - - ns tw2L Low period pulse width of SDEN 1 - - s 2) 3-wire serial bus transfer formats LV5239TA receives the command by communication format by 3 line type serial communication of SCLK, SDATA, and SDEN. When SCLK stops in “L” level When SCLK stops in “H” level Data length : 24bits Clock frequency : 5MHz or less When 24 SCLK clock signals have been input during the high period of SDEN, the SDATA is taken in at the rising edge of SCLK. Note: If the number of SCLK clock signals during the high period of SDEN is 23 or less, SDATA is not taken in. If it is 25 or more, the register address is automatically incremented every time 1byte is taken in. Data organization The slave address is assigned by the first byte, and the register address on the serial map is specified by the next byte. The third byte transfers the data to the address specified by the register address that was written by the second byte and if the data subsequently continues even after this, the register address is automatically incremented for the fourth and subsequent bytes. As a result, it is possible to send the data continuously from the specified addresses. Data of less than one byte is ignored. However, when the address reaches 1fh, the next byte to be transferred becomes 00h. www.onsemi.com 11 LV5239TA Serial data transfer example (slave address=1000 001- ) When I set register address 02h and write in data (the smallest data length) SDEN SDATA 1 0 0 0 0 0 Slave address 1 - 0 0 0 0 0 0 1 Register address 02h is set 0 Data 1 (1byte) Data is written into address 02h When I set register address 02h and write in data for 3 bytes When I set register address 02h and write in data for 3 byte, and following data is less than a signal byte When slave address does not accord www.onsemi.com 12 LV5239TA 3) 2-wire serial bus transfer formats LV5239TA receives the command by communication format by 2 line type serial communication of SCLK, SDATA. When SCLK stops in “L” level When SCLK stops in “H” level Data length : 37bits Start condition (“111111111”) + BLANK (“0”) + Slave address (8bit) + BLANK + (“0”) + Resister address (8bit) + BLANK (“0”) + Data (8bit) + BLANK (“0”) Clock frequency : 5MHz or less After start detection, it takes SDATA in the timing when the 27th clock track of SCLK stands up when sign according to communication format is input into SCLK and SDATA. Note: When SCLK is less than 27th clock track, and BLANK is different from communication format such as “1”, after start detection, do not take in SDATA. When SCLK is higher than 28th clock track, start detection is confirmed, or it is automatic, and register address is incremented every 1byte (8bit) + BLANK (“0”) unless BLANL is “1”. Data organization Even if SCLK and SDATA are state such as among standby or serial data inward correspondences, “111111111” start assumption and BLANK”0” start the uptake atomic act of new serial data after detection (start detection) was considered to be it. After start detection, the first single byte (8bit) is assigned to slave address, and a write store of the slave address completes it in BLANK”0”. The next single byte appoints register address in the serial manufacturing auto protocol, and a write of the register address is completed in BLANK”0”. The third byte performs a data transfer to the address which it appointed in the register address which it wrote in at the second byte and it complete data transfer in BLANK”0” and write in it. When data continues after this, register address is automatically incremented after the fourth byte and a data transfer is completed each time and, in BLANK”0”, writes in it. Data Forward continuous from designated register address is enabled, but, as for the redirecting address of the next byte, it is in this way with for “00h” when register address becomes “1Fh”. In addition, when serial data uptake BLANK is “1”, including slave address selection and register address assignment, the single byte data just before it is ignored without being written in, and the subsequent data is ignored until it is detected a start. www.onsemi.com 13 LV5239TA Serial data transfer example (slave address=1000 001- ) When I set register address 02h and write in data (the smallest data length) When I set register address 02h and write in data for 3 bytes When I set register address 02h and write in data for 1 byte, and BLANK after the following byte in the case of “1” When I set register address 02h, but BLANK after the byte in the case of “1” When slave address does not accord SDATA continues more than 10bit; and in the case of 1 "" (start detection of this case) www.onsemi.com 14 LV5239TA Slave address condition SLAVE ADDRESS SA7 SA6 SA5 SA4 SA3 SA2 SA1 SA0 resister name - - A4 A3 A2 A1 A0 - default 1 0 0 0 0 0 0 - Terminal PIN A4 A3 A2 :LV5239 A1 A0 SA7 SA6 SA5 SA4 SA3 SA2 SA1 SA0 L L L L L 1 0 0 0 0 0 0 - L L L L H 1 0 0 0 0 0 1 - L L L H L 1 0 0 0 0 1 0 - L L L H H 1 0 0 0 0 1 1 - L L H L L 1 0 0 0 1 0 0 - L L H L H 1 0 0 0 1 0 1 - L L H H L 1 0 0 0 1 1 0 L L H H H 1 0 0 0 1 1 1 - L H L L L 1 0 0 1 0 0 0 - L H L L H 1 0 0 1 0 0 1 - L H L H L 1 0 0 1 0 1 0 - L H L H H 1 0 0 1 0 1 1 - L H H L L 1 0 0 1 1 0 0 - L H H L H 1 0 0 1 1 0 1 - L H H H L 1 0 0 1 1 1 0 - L H H H H 1 0 0 1 1 1 1 - H L L L L 1 0 1 0 0 0 0 - H L L L H 1 0 1 0 0 0 1 - H L L H L 1 0 1 0 0 1 0 - H L L H H 1 0 1 0 0 1 1 - H L H L L 1 0 1 0 1 0 0 - H L H L H 1 0 1 0 1 0 1 - H L H H L 1 0 1 0 1 1 0 H L H H H 1 0 1 0 1 1 1 - H H L L L 1 0 1 1 0 0 0 - H H L L H 1 0 1 1 0 0 1 - H H L H L 1 0 1 1 0 1 0 H H L H H 1 0 1 1 0 1 1 - H H H L L 1 0 1 1 1 0 0 - H H H L H 1 0 1 1 1 0 1 - H H H H L 1 0 1 1 1 1 0 - H H H H H 1 0 1 1 1 1 1 - www.onsemi.com 15 LV5239TA Serial each mode setting ADDRESS : 00h D7 D6 D5 D4 D3 D2 D1 D0 register name PWM[2] PWM[1] PWM[0] - - RLED[2] RLED[1] RLED[0] default 0 0 0 0 0 0 0 0 D7 D6 D5 time(ms) 0 0 0 0.5 PWM cycle setting 0 0 1 1.0 0 1 0 2.0 0 1 1 4.0 1 0 0 8.0 - - - - - - - - - - - - - - - - D2 D1 D0 Current value (mA) 0 0 0 6.40 0 0 1 10.15 0 1 0 13.90 0 1 1 17.65 1 0 0 21.15 1 0 1 24.90 1 1 0 28.65 1 1 1 32.40 *Default RLED current value setting * Default www.onsemi.com 16 LV5239TA ADDRESS : 01h D7 D6 D5 D4 D3 D2 D1 D0 register name - - - - - GLED[2] GLED[1] GLED[0] default 0 0 0 0 0 0 0 0 D2 D1 D0 Current value (mA) 0 0 0 6.40 0 0 1 10.15 0 1 0 13.90 0 1 1 17.65 1 0 0 21.15 1 0 1 24.90 1 1 0 28.65 1 1 1 32.40 GLED current value setting * Default www.onsemi.com 17 LV5239TA ADDRESS : 02h D7 D6 D5 D4 D3 D2 D1 D0 register name - - - - - BLED[2] BLED[1] BLED[0] default 0 0 0 0 0 0 0 0 D2 D1 D0 Current value (mA) 0 0 0 6.40 0 0 1 10.15 0 1 0 13.90 0 1 1 17.65 1 0 0 21.15 1 0 1 24.90 1 1 0 28.65 1 1 1 32.40 BLED current value setting * Default www.onsemi.com 18 LV5239TA ADDRESS : 03h D7 D6 D5 D4 D3 D2 D1 D0 register name R8OUT R7OUT R6OUT R5OUT R4OUT R3OUT R2OUT R1OUT default 0 0 0 0 0 0 0 0 D7 R8OUT 0 PWM mode-Duty setting 1 100%-Duty setting D6 R7OUT 0 PWM mode-Duty setting 1 100%-Duty setting D5 R6OUT 0 PWM mode-Duty setting 1 100%-Duty setting D4 R5OUT 0 PWM mode-Duty setting 1 100%-Duty setting D3 R4OUT 0 PWM mode-Duty setting 1 100%-Duty setting D2 R3OUT 0 PWM mode-Duty setting 1 100%-Duty setting D1 R2OUT 0 PWM mode-Duty setting 1 100%-Duty setting D0 R1OUT 0 PWM mode-Duty setting 1 100%-Duty setting LEDR8 output duty setting * Default LEDR7 output duty setting * Default LEDR6 output duty setting * Default LEDR5 output duty setting * Default LEDR4 output duty setting * Default LEDR3 output duty setting * Default LEDR2 output duty setting * Default LEDR1 output duty setting * Default www.onsemi.com 19 LV5239TA ADDRESS : 04h D7 D6 D5 D4 D3 D2 D1 D0 register name G8OUT G7OUT G6OUT G5OUT G4OUT G3OUT G2OUT G1OUT default 0 0 0 0 0 0 0 0 D7 G8OUT 0 PWM mode-Duty setting 1 100%-Duty setting D6 G7OUT 0 PWM mode-Duty setting 1 100%-Duty setting D5 G6OUT 0 PWM mode-Duty setting 1 100%-Duty setting D4 G5OUT 0 PWM mode-Duty setting 1 100%-Duty setting D3 G4OUT 0 PWM mode-Duty setting 1 100%-Duty setting D2 G3OUT 0 PWM mode-Duty setting 1 100%-Duty setting D1 G2OUT 0 PWM mode-Duty setting 1 100%-Duty setting D0 G1OUT 0 PWM mode-Duty setting 1 100%-Duty setting LEDG8 output duty setting * Default LEDG7 output duty setting * Default LEDG6 output duty setting * Default LEDG5 output duty setting * Default LEDG4 output duty setting * Default LEDG3 output duty setting * Default LEDG2 output duty setting * Default LEDG1 output duty setting * Default www.onsemi.com 20 LV5239TA ADDRESS : 05h D7 D6 D5 D4 D3 D2 D1 D0 register name B8OUT B7OUT B6OUT B5OUT B4OUT B3OUT B2OUT B1OUT default 0 0 0 0 0 0 0 0 D7 B8OUT 0 PWM mode-Duty setting 1 100%-Duty setting D6 B7OUT 0 PWM mode-Duty setting 1 100%-Duty setting D5 B6OUT 0 PWM mode-Duty setting 1 100%-Duty setting D4 B5OUT 0 PWM mode-Duty setting 1 100%-Duty setting D3 B4OUT 0 PWM mode-Duty setting 1 100%-Duty setting D2 B3OUT 0 PWM mode-Duty setting 1 100%-Duty setting D1 B2OUT 0 PWM mode-Duty setting 1 100%-Duty setting D0 B1OUT 0 PWM mode-Duty setting 1 100%-Duty setting LEDB8 output duty setting * Default LEDB7 output duty setting * Default LEDB6 output duty setting * Default LEDB5 output duty setting * Default LEDB4 output duty setting * Default LEDB3 output duty setting * Default LEDB2 output duty setting * Default LEDB1 output duty setting * Default www.onsemi.com 21 LV5239TA ADDRESS : 06h D7 D6 D5 D4 D3 D2 D1 D0 register name R1PWM[7] R1PWM[6] R1PWM[5] R1PWM[4] R1PWM[3] R1PWM[2] R1PWM[1] R1PWM[0] default 0 0 0 0 0 0 0 0 LEDR1 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R1PWM[7:0] 256 ADDRESS : 07h D7 D6 D5 D4 D3 D2 D1 D0 register name G1PWM[7] G1PWM[6] G1PWM[5] G1PWM[4] G1PWM[3] G1PWM[2] G1PWM[1] G1PWM[0] default 0 0 0 0 0 0 0 0 LEDG1 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G1PWM[7:0] 256 ADDRESS : 08h D7 D6 D5 D4 D3 D2 D1 D0 register name B1PWM[7] B1PWM[6] B1PWM[5] B1PWM[4] B1PWM[3] B1PWM[2] B1PWM[1] B1PWM[0] default 0 0 0 0 0 0 0 0 LEDB1 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B1PWM[7:0] 256 ADDRESS : 09h D7 D6 D5 D4 D3 D2 D1 D0 register name R2PWM[7] R2PWM[6] R2PWM[5] R2PWM[4] R2PWM[3] R2PWM[2] R2PWM[1] R2PWM[0] default 0 0 0 0 0 0 0 0 LEDR2 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R2PWM[7:0] 256 ADDRESS : 0ah D7 D6 D5 D4 D3 D2 D1 D0 register name G2PWM[7] G2PWM[6] G2PWM[5] G2PWM[4] G2PWM[3] G2PWM[2] G2PWM[1] G2PWM[0] default 0 0 0 0 0 0 0 0 LEDG2 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G2PWM[7:0] 256 ADDRESS : 0bh D7 D6 D5 D4 D3 D2 D1 D0 register name B2PWM[7] B2PWM[6] B2PWM[5] B2PWM[4] B2PWM[3] B2PWM[2] B2PWM[1] B2PWM[0] default 0 0 0 0 0 0 0 0 LEDB2 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B2PWM[7:0] 256 www.onsemi.com 22 LV5239TA ADDRESS : 0ch D7 D6 D5 D4 D3 D2 D1 D0 register name R3PWM[7] R3PWM[6] R3PWM[5] R3PWM[4] R3PWM[3] R3PWM[2] R3PWM[1] R3PWM[0] default 0 0 0 0 0 0 0 0 LEDR3 PWM Duty setting (DefaultALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R3PWM[7:0] 256 ADDRESS : 0dh D7 D6 D5 D4 D3 D2 D1 D0 register name G3PWM[7] G3PWM[6] G3PWM[5] G3PWM[4] G3PWM[3] G3PWM[2] G3PWM[1] G3PWM[0] default 0 0 0 0 0 0 0 0 LEDG3 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G3PWM[7:0] 256 ADDRESS : 0eh D7 D6 D5 D4 D3 D2 D1 D0 register name B3PWM[7] B3PWM[6] B3PWM[5] B3PWM[4] B3PWM[3] B3PWM[2] B3PWM[1] B3PWM[0] default 0 0 0 0 0 0 0 0 LEDB3 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B3PWM[7:0] 256 ADDRESS : 0fh D7 D6 D5 D4 D3 D2 D1 D0 register name R4PWM[7] R4PWM[6] R4PWM[5] R4PWM[4] R4PWM[3] R4PWM[2] R4PWM[1] R4PWM[0] default 0 0 0 0 0 0 0 0 LEDR4 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R4PWM[7:0] 256 ADDRESS : 10h D7 D6 D5 D4 D3 D2 D1 D0 register name G4PWM[7] G4PWM[6] G4PWM[5] G4PWM[4] G4PWM[3] G4PWM[2] G4PWM[1] G4PWM[0] default 0 0 0 0 0 0 0 0 LEDG4 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G4PWM[7:0] 256 ADDRESS : 11h D7 D6 D5 D4 D3 D2 D1 D0 register name B4PWM[7] B4PWM[6] B4PWM[5] B4PWM[4] B4PWM[3] B4PWM[2] B4PWM[1] B4PWM[0] default 0 0 0 0 0 0 0 0 LEDB4 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B4PWM[7:0] 256 www.onsemi.com 23 LV5239TA ADDRESS : 12h D7 D6 D5 D4 D3 D2 D1 D0 register name R5PWM[7] R5PWM[6] R5PWM[5] R5PWM[4] R5PWM[3] R5PWM[2] R5PWM[1] R5PWM[0] default 0 0 0 0 0 0 0 0 LEDR5 PWM Duty setting (DefaultALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R5PWM[7:0] 256 ADDRESS : 13h D7 D6 D5 D4 D3 D2 D1 D0 register name G5PWM[7] G5PWM[6] G5PWM[5] G5PWM[4] G5PWM[3] G5PWM[2] G5PWM[1] G5PWM[0] default 0 0 0 0 0 0 0 0 LEDG5 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G5PWM[7:0] 256 ADDRESS : 14h D7 D6 D5 D4 D3 D2 D1 D0 register name B5PWM[7] B5PWM[6] B5PWM[5] B5PWM[4] B5PWM[3] B5PWM[2] B5PWM[1] B5PWM[0] default 0 0 0 0 0 0 0 0 LEDB5 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B5PWM[7:0] 256 ADDRESS : 15h D7 D6 D5 D4 D3 D2 D1 D0 register name R6PWM[7] R6PWM[6] R6PWM[5] R6PWM[4] R6PWM[3] R6PWM[2] R6PWM[1] R6PWM[0] default 0 0 0 0 0 0 0 0 LEDR6 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R6PWM[7:0] 256 ADDRESS : 16h D7 D6 D5 D4 D3 D2 D1 D0 register name G6PWM[7] G6PWM[6] G6PWM[5] G6PWM[4] G6PWM[3] G6PWM[2] G6PWM[1] G6PWM[0] default 0 0 0 0 0 0 0 0 LEDG6 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G6PWM[7:0] 256 ADDRESS : 17h D7 D6 D5 D4 D3 D2 D1 D0 register name B6PWM[7] B6PWM[6] B6PWM[5] B6PWM[4] B6PWM[3] B6PWM[2] B6PWM[1] B6PWM[0] default 0 0 0 0 0 0 0 0 LEDB6 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B6PWM[7:0] 256 www.onsemi.com 24 LV5239TA ADDRESS : 18h D7 D6 D5 D4 D3 D2 D1 D0 register name R7PWM[7] R7PWM[6] R7PWM[5] R7PWM[4] R7PWM[3] R7PWM[2] R7PWM[1] R7PWM[0] default 0 0 0 0 0 0 0 0 LEDR7 PWM Duty setting (DefaultALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R7PWM[7:0] 256 ADDRESS : 19h D7 D6 D5 D4 D3 D2 D1 D0 register name G7PWM[7] G7PWM[6] G7PWM[5] G7PWM[4] G7PWM[3] G7PWM[2] G7PWM[1] G7PWM[0] default 0 0 0 0 0 0 0 0 LEDG7 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G7PWM[7:0] 256 ADDRESS : 1ah D7 D6 D5 D4 D3 D2 D1 D0 register name B7PWM[7] B7PWM[6] B7PWM[5] B7PWM[4] B7PWM[3] B7PWM[2] B7PWM[1] B7PWM[0] default 0 0 0 0 0 0 0 0 LEDB7 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B7PWM[7:0] 256 ADDRESS : 1bh D7 D6 D5 D4 D3 D2 D1 D0 register name R8PWM[7] R8PWM[6] R8PWM[5] R8PWM[4] R8PWM[3] R8PWM[2] R8PWM[1] R8PWM[0] default 0 0 0 0 0 0 0 0 LEDR8 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R8PWM[7:0] 256 ADDRESS : 1ch D7 D6 D5 D4 D3 D2 D1 D0 register name G8PWM[7] G8PWM[6] G8PWM[5] G8PWM[4] G8PWM[3] G8PWM[2] G8PWM[1] G8PWM[0] default 0 0 0 0 0 0 0 0 LEDG8 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G8PWM[7:0] 256 ADDRESS : 1dh D7 D6 D5 D4 D3 D2 D1 D0 register name B8PWM[7] B8PWM[6] B8PWM[5] B8PWM[4] B8PWM[3] B8PWM[2] B8PWM[1] B8PWM[0] default 0 0 0 0 0 0 0 0 LEDB8 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B8PWM[7:0] 256 www.onsemi.com 25 LV5239TA LV5239TA serial map • Table upper row: Register name 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0ah 0bh 0ch 0dh 0eh 0fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1ah Table the lower: Default value A7 A6 A5 A4 A3 A2 A1 A0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 D7 D6 D5 D4 D3 0 0 0 0 0 0 0 0 0 0 PWM[2:0] D2 D1 D0 RLED[2:0] 0 0 0 GLED[2:0] 0 0 0 BLED[2:0] 0 0 0 0 0 0 0 0 R8OUT R7OUT R6OUT R5OUT R4OUT R3OUT R2OUT R1OUT 0 0 0 0 0 0 0 0 G8OUT G7OUT G6OUT G5OUT G4OUT G3OUT G2OUT G1OUT 0 0 0 0 0 0 0 0 B8OUT B7OUT B6OUT B5OUT B4OUT B3OUT B2OUT B1OUT 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R1PWM[7:0] 0 0 0 0 0 G1PWM[7:0] 0 0 0 0 0 B1PWM[7:0] 0 0 0 0 0 R2PWM[7:0] 0 0 0 0 0 G2PWM[7:0] 0 0 0 0 0 B2PWM[7:0] 0 0 0 0 0 R3PWM[7:0] 0 0 0 0 0 G3PWM[7:0] 0 0 0 0 0 B3PWM[7:0] 0 0 0 0 0 R4PWM[7:0] 0 0 0 0 0 G4PWM[7:0] 0 0 0 0 0 B4PWM[7:0] 0 0 0 0 0 R5PWM[7:0] 0 0 0 0 0 G5PWM[7:0] 0 0 0 0 0 B5PWM[7:0] 0 0 0 0 0 R6PWM[7:0] 0 0 0 0 0 G6PWM[7:0] 0 0 0 0 0 B6PWM[7:0] 0 0 0 0 0 R7PWM[7:0] 0 0 0 0 0 G7PWM[7:0] 0 0 0 0 0 B7PWM[7:0] 0 0 Register address 0 0 0 Data Continued on next page. www.onsemi.com 26 LV5239TA Continued from preceding page. A7 A6 A5 A4 A3 A2 A1 A0 1bh 0 0 0 1 1 0 1 1 1ch 0 0 0 1 1 1 0 0 1dh 0 0 0 1 1 1 0 1 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 0 R8PWM[7:0] 0 0 0 0 0 0 0 0 G8PWM[7:0] 0 0 B8PWM[7:0] 0 0 Register address 0 0 0 Data www.onsemi.com 27 LV5239TA ORDERING INFORMATION Device LV5239TAZ-NH Package Shipping (Qty / Packing) TQFP48 EP 7x7, 0.5P (Pb-Free / Halogen Free) 1000 / Tape & Reel † For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://www.onsemi.com/pub_link/Collateral/BRD8011-D.PDF ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf . SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. www.onsemi.com 28