Ordering number : ENA1943B LV5236V Bi-CMOS IC 24-channel LED Driver http://onsemi.com Overview The LV5236V is a 24-channel LED driver IC that is capable of switching between constant-current output and open drain output. It enables 3-wire serial bus control (address designation)/I2C serial bus control to be set arbitrarily using an external pin. Also possible are 24-channel LED ON/OFF control and the setting of the PWM luminance in 256 steps. The device also has a built-in fade-in/fade-out function. Up to 32 driver ICs can be connected using the slave address setting pins. Function • 24-channel output constant-current LED driver/open drain output LED driver (selected by using an external pin) Supports separate ON/OFF setting for each LED output, high withstand voltage (VOUT<42V) • In the constant-current mode (OUTSCT: L), the reference current is set by the value of resistor connected to the external pin (RT1). Built-in D/A (5 bits) for switching current level … 0.96mA to 30.7mA (RGB drive) Constant current (IO max=50mA) for full-color SSOP44J (275mil) LEDs × 24 channels • In the open drain mode (OUTSCT: M), high current drive (IO max=100mA) × 24 channels • In the constant-current mode (OUTSCT: H) Only RGB6 is open drain (IO max=100mA) • Luminance adjustment using internal PWM control (256 steps) • 8-bit PWM luminance dimming (0% to 99.6%) • 8-phase PWM • Fade-in/fade-out function (PWM control priority), supporting synchronous connection • Supports separate fade ON/OFF for each LED output (fade time common for all channels) • Interrupt control possible for fade function • Selection of 3-wire/I2C serial bus control signals enabled (switching using an external pin) Slave addressing (5 bits, connection of up to 32 driver ICs possible) • Low current consumption • Output malfunction protection circuits (thermal protection function, UVLO detection protection function) * I2C Bus is a trademark of Philips Corporation. ORDERING INFORMATION See detailed ordering and shipping information on page 36 of this data sheet. Semiconductor Components Industries, LLC, 2014 March, 2014 30614NK/82411SY/32311SY 20110303-S00002,20110303-S00004 No.A1943-1/36 LV5236V Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit Maximum supply voltage VCC max Output voltage VO max 6 Output current IO max Allowable power dissipation Pd max 1.36 W Operating temperature Topr -25 to +75 °C Storage temperature Tstg -40 to +125 °C LED off Ta ≤ 25°C * V 42 V 100 mA * Specified board : 114.3mm × 76.1mm × 1.6mm, glass epoxy board. Exposed Die-pad area is not a substrate mounting. [Warning]: If you should intend to use this IC continuously under high temperature, high current, high voltage, or drastic temperature change, even if it is used within the range of absolute maximum ratings or operating conditions, there is a possibility of decrease reliability. Please contact us for a confirmation. Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. Recommended Operating Conditions at Ta = 25°C Parameter Symbol Conditions Ratings Unit Recommended supply voltage VCC SVCC 5.0 V Operating supply voltage range VCC op SVCC 4.5 to 5.5 V Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. Electrical Characteristics at Ta = 25°C, VCC = 5V Parameter Symbol Conditions Consumption current ICC2 Oscillator frequency Fosc Reference current pin voltage VRT RT1=22kΩ MAX output current ΔIL VO=0.7 to 4.0V(Same channel line regulation) Between bits output current ΔIOL IO=30.7mA (Between bits pairing Ratings min LED off typ Unit max 5 7 mA 900 1000 1100 kHz 0.92 0.98 1.04 V -10 % 5 % 30.7 32.6 mA 11 22 Ω 4 10 Ω 10 μA 2.82 V characteristics) Maximum LED driver output IMAX1 LED OUTSCT= L Ron1 LED1, LED2, LED3, LED4, LED5, LED7, LED output on resistance 2 Ron2 LED8 (IO = 100mA) LED6 (IO = 100mA) OFF leak current Ileak LED OFF Driver output malfunction Vt SVCC 28.8 current 1 LED output on resistance 1 2.58 2.70 protection voltage Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. No.A1943-2/36 LV5236V Control circuit at Ta = 25°C, VCC = 5.0V Parameter Symbol Conditions Ratings min typ Unit max H level 1 VH1 Input H level OUTSCT 4.7 5 V M level 1 VM1 Input M level OUTSCT 2 3.3 V L level 1 VL1 Input L level OUTSCT -0.2 0.3 V H level 2 VH2 Input H level CTLSCT 0.7× VCC VCC V L level 2 VL2 Input L level CTLSCT -0.2 0.3 V H level 3 VH3 Input H level RESET 0.8× VCC VCC V L level 3 VL3 Input L level RESET -0.2 0.2× VCC V H level 4 VH4 Input H level SCLK, SDATA, SDEN 0.8× VCC VCC V L level 4 VL4 Input L level SCLK, SDATA, SDEN -0.2 0.2× VCC V H level 5 VH7 Input H level A0 to A4 0.7× VCC VCC V L level 5 VL7 Input L level A0 to A4 -0.2 0.3 V Package Dimensions SSOP44J (275mil) Exposed Pad CASE 940AG ISSUE A No.A1943-3/36 LV5236V 1.00 SOLDERING FOOTPRINT* (Unit: mm) 7.00 (3.6) (7.8) 0.65 0.32 NOTES: 1. The measurements are for reference only, and unable to guarantee. 2. Please take appropriate action to design the actual Exposed Die Pad and Fin portion. 3. After setting, verification on the product must be done. (Although there are no recommended design for Exposed Die Pad and Fin portion Metal mask and shape for Through−Hole pitch (Pitch & Via etc), checking the soldered joint condition and reliability verification of soldered joint will be needed. Void gradient insufficient thickness of soldered joint or bond degradation could lead IC destruction because thermal conduction to substrate becomes poor.) *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. GENERIC MARKING DIAGRAM* XXXXXXXXXX YMDDD XXXXX = Specific Device Code Y = Year M = Month DDD = Additional Traceability Data No.A1943-4/36 LV5236V Pd max -- Ta Allowable power dissipation, Pd max -- W 1.6 Specified board : 114.3 × 76.1 × 1.6mm3 glass epoxy 1.4 1.36 1.2 1.0 0.8 0.68 0.6 0.4 0.2 0 --25 0 25 50 75 100 Ambient temperature, Ta -- C LEDB1 LEDB2 LEDB3 LEDB4 PGND3 LEDB5 LEDB6 LEDB7 LEDB8 OUTSCT TEST RESET CTLSCT SDEN SCLK SDATA A0 A1 A2 A3 A4 Block Diagram SVCC SGND Serial Bus I/F BGR BLED-D/A OSC_OUT OSC PWM BRIGHTNESS FADE-IN/OUT CONTROL LEDG8 LEDG7 LEDG4 LEDG3 LEDG2 LEDG1 LEDR8 LEDR7 GLED-D/A LEDR6 LEDR5 PGND1 LEDR4 LEDR3 LEDR2 LEDR1 RLED-D/A LEDG6 I-REG D/A LEDG5 RT1 PGND2 CT No.A1943-5/36 LV5236V Pin Assignment LEDG6 LEDG7 LEDG8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 A0 LEDG5 8 A1 PGND2 7 A2 LEDG4 6 A3 LEDG3 5 A4 LEDG2 4 LEDB1 LEDB3 LEDG1 3 LEDB2 LEDB4 LEDR8 2 PGND3 LEDR7 1 LEDB5 LEDB6 23 LEDR6 24 LEDB7 25 LEDR5 26 LEDB8 27 PGND1 28 CTLSCT 29 LEDR4 30 SGND 31 LEDR3 32 TEST 33 LEDR2 34 RESET 35 LEDR1 36 RT1 37 SDEN 38 CT 39 SDATA 40 OUTSCT 41 SCLK 42 OSC_OUT 43 SVCC 44 Top view Pin Descriptions Pin No. 1 Pin name I/O Description SVCC - Power supply pin 2 SCLK I Serial clock signal input pin 3 SDATA I Serial data signal input pin 4 SDEN I Serial enable signal input pin 5 LEDR1 O LEDR1 output pin 6 LEDR2 O LEDR2 output pin 7 LEDR3 O LEDR3 output pin 8 LEDR4 O LEDR4 output pin 9 PGND1 - GND pin dedicated for LED driver 10 LEDR5 O LEDR5 output pin 11 LEDR6 O LEDR6 output pin 12 LEDR7 O LEDR7 output pin 13 LEDR8 O LEDR8 output pin 14 LEDG1 O LEDG1 output pin 15 LEDG2 O LEDG2 output pin 16 LEDG3 O LEDG3 output pin 17 LEDG4 O LEDG4 output pin 18 PGND2 - GND pin dedicated for LED driver 19 LEDG5 O LEDG5 output pin 20 LEDG6 O LEDG6 output pin 21 LEDG7 O LEDG7 output pin 22 LEDG8 O LEDG8 output pin 23 A0 I Slave address input pin A0 24 A1 I Slave address input pin A1 25 A2 I Slave address input pin A2 26 A3 I Slave address input pin A3 27 A4 I Slave address input pin A4 Continued on next page. No.A1943-6/36 LV5236V Continued from preceding page. Pin No. Pin name I/O Description 28 LEDB1 O LEDB1 output pin 29 LEDB2 O LEDB2 output pin 30 LEDB3 O LEDB3 output pin 31 LEDB4 O LEDB4 output pin 32 PGND3 - GND pin dedicated for LED driver 33 LEDB5 O LEDB5 output pin 34 LEDB6 O LEDB6 output pin 35 LEDB7 O LEDB7 output pin 36 LEDB8 O LEDB8 output pin 37 CTLSCT I 3-wire serial bus/I2C serial bus selecting control pin (L: 3-wire serial, H: I2C) 38 SGND - Analog circuit GND pin 39 TEST I Test pin (connected to GND) 40 RESET I Reset signal input pin 41 RT1 O LED current setting resistor connection pin 1 42 CT O Oscillation frequency setting capacitor connection pin 43 OUTSCT I Output type switching control pin L: Constant-current output M (terminal OPEN): Open drain output H: Constant output, only RGB6 is open drain output 44 OSC_OUT O Oscillator output pin (synchronous connection) OUTSCT Settings LED Driver Output Pin OUTSCT pin L=-0.2 to 0.3V LED1, LED2, LED3, LED4, LED5, LED7, LED8 LED6 Constant current output Constant current output Built-in current value switching D/A (5 bits) Built-in current value switching D/A (5 bits) 0.96mA to 30.7mA, RT1=22kΩ (f=1MHz) 0.96mA to 30.7mA, RT1=22kΩ (f=1MHz) M=2.0 to 3.3V Open drain output Open drain output (terminal OPEN) Current value is determined by external limiting resistor. Current value is determined by external limiting resistor. H=4.7 to 5.0V RON=11Ω Constant current output RON=4Ω Open drain output Built-in current value switching D/A (5 bits) Current value is determined by external limiting resistor. 0.96mA to 30.7mA, RT1=22kΩ (f=1MHz) RON=4Ω No.A1943-7/36 LV5236V Pin Functions Pin No. Pin Name Pin function 1 SVCC Power supply pin 2 SCLK Serial clock signal input pin 3 SDATA Serial data signal input pin 4 SDEN Serial enable signal input pin 23 A0 Slave address setting pin A0 24 A1 Slave address setting pin A1 25 A2 Slave address setting pin A2 26 A3 Slave address setting pin A3 27 A4 Slave address setting pin A4 37 CTLSCT Serial bus communication setting pin Equivalent Circuit SVCC SVCC When set to low: The 3-wire serial bus signals are set as the input signals. When set to high: The I2C serial bus signals are set as the input signals. 38 SGND GND pin 39 TEST Test pin SVCC This pin must always be connected to GND. 40 RESET Reset signal input pin Reset status when set to low. 41 RT1 Reference current setting resistor connection pin. SVCC SVCC By connecting the external register between this pin and GND, the reference current is generated. The pin voltage is approximately 0.98V. By changing the current level, it is possible to change the oscillator frequency and LED driver current value (in the constant-current mode). Continued on next page. No.A1943-8/36 LV5236V Continued from preceding page. Pin No. 42 Pin Name CT Pin function Oscillator frequency setting capacitor connection pin/oscillator input pin. Equivalent Circuit SVCC Internal Reference By changing the value of capacitance, it is possible to change the oscillator frequency. The capacitor must be connected to this pin of the master-side IC. The CT pin of the slave-side IC must be connected as the + + oscillator input pin. 43 OUTSCT LED driver output type setting pin When set to low: Constant-current output is SVCC set for the LED driver. When set to middle: Open drain output is set for the LED driver. When set to high: Constant-current output is set for the LED driver. However, open drain output is set for the only LED6 driver. 44 OSC_OUT Oscillator output pin When a multiple number of driver ICs are SVCC connected for use, the oscillators can be connected in synchronization by connecting the OSC_OUT output to the CT pin of the ICs to be connected. 5 LEDR1 LEDR1 output pin 6 LEDR2 LEDR2 output pin 7 LEDR3 LEDR3 output pin 8 LEDR4 LEDR4 output pin 10 LEDR5 LEDR5 output pin 12 LEDR7 LEDR7 output pin 13 LEDR8 LEDR8 output pin 14 LEDG1 LEDG1 output pin 15 LEDG2 LEDG2 output pin 16 LEDG3 LEDG3 output pin 17 LEDG4 LEDG4 output pin 19 LEDG5 LEDG5 output pin 21 LEDG7 LEDG7 output pin 22 LEDG8 LEDG8 output pin 28 LEDB1 LEDB1 output pin 29 LEDB2 LEDB2 output pin 30 LEDB3 LEDB3 output pin 31 LEDB4 LEDB4 output pin 33 LEDB5 LEDB5 output pin 35 LEDB7 LEDB7 output pin 36 LEDB8 LEDB8 output pin If these pins are not going to be used, they must always be connected to GND. 11 LEDR6 LEDR6 output pin 20 LEDG6 LEDG6 output pin 34 LEDB6 LEDB6 output pin 9 PGND1 GND pin dedicate for LEDR 18 PGND2 GND pin dedicate for LEDG 32 PGND3 GND pin dedicate for LEDB No.A1943-9/36 LV5236V Application Circuit Diagrams ● Specifications when one driver IC is used VLED 100pF 5V 5V A2 A1 A0 PGND2 LEDG5 LEDG6 LEDG7 LEDG8 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 A3 LEDG4 5 A4 LEDG3 4 LEDB1 LEDB3 LEDG2 3 LEDB2 LEDB4 LEDG1 2 LEDB5 LEDR8 1 PGND3 LEDB6 LEDR7 23 LEDB7 24 LEDR6 25 LEDB8 26 LEDR5 27 CTLSCT 28 PGND1 29 LEDR4 30 TEST 31 SGND 32 LEDR3 33 RESET 34 LEDR2 35 LEDR1 36 CT 37 RT1 38 SDEN 39 OUTSCT 40 SDATA 41 OSC_OUT 42 SCLK 43 SVCC 44 Use as a master-side IC Slave selection: A0-A4: low Address setting: Master (100-0000) 5V I2C Serial Bus Micon ● Specifications when more than one driver IC is used 5V CT RT1 RESET TEST SGND CTLSCT LEDB8 LEDB7 LEDB6 LEDB5 PGND3 LEDB4 LEDB3 LEDB2 LEDB1 A4 A3 A2 A1 A0 LEDG8 OUTSCT LEDG7 23 LEDG6 24 LEDG5 25 PGND2 26 LEDG4 27 LEDG3 28 LEDG2 29 LEDG1 30 LEDR8 31 LEDR7 32 LEDR6 33 LEDR5 34 PGND1 35 LEDR4 36 LEDR3 37 LEDR2 38 LEDR1 39 SDEN 40 SDATA 41 SCLK 42 SVCC 43 OSC_OUT 5V 44 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 5V Use as a slave-side IC Slave selection: A0 high: A1-A4 low Address setting: Slave (100-0001) Use as a master-side IC Slave selection: A0-A4: low Address setting: Master (100-0000) 100pF 5V LEDG7 LEDG8 A0 LEDG6 A1 LEDG5 A2 PGND2 A3 LEDG4 A4 LEDG3 LEDB1 LEDB3 LEDG2 LEDB2 LEDB4 LEDG1 PGND3 LEDR8 LEDB5 LEDR7 23 LEDB6 24 LEDR6 25 LEDB7 26 LEDR5 27 LEDB8 28 CTLSCT 29 PGND1 30 LEDR4 31 SGND 32 LEDR3 33 TEST 34 RESET 35 LEDR2 36 LEDR1 37 RT1 38 SDEN 39 SDATA 40 OUTSCT 41 OSC_OUT 42 SCLK 43 SVCC 44 CT 5V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 The oscillator frequency is determined by the master IC. The synchronous connection of the oscillator can be established by connecting the oscillator output (OSC_OUT) to the CT pins of the slave-side ICs. 5V I2C Serial Bus Micon VLED No.A1943-10/36 LV5236V Serial Bus Communication Specifications 1) 3-wire serial bus transfer timing conditions SDEN ts0 th0 SCLK tw2H 50% ts1 tw1H tw1L th1 tcy1 SDATA SA7 SA6 SA5 SA4 SA3 SA2 SA1 SA0 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D4 D5 D3 D2 D1 D0 SA7 Parameter Symbol Conditions Min. Typ. Max. Unit Cycle time tcy1 SCLK clock period 200 - - ns Data setup time ts0 SDEN setup time relative to the rise of SCLK 90 - - ns ts1 SDATA setup time relative to the rise of SCLK 60 - - ns Data hold time Pulse width th0 SDEN hold time relative to the fall of SCLK 200 - - ns th1 SDATA hold time relative to the fall of SCLK 60 - - ns tw1L Low period pulse width of SCLK 90 - - ns tw1H High period pulse width of SCLK 90 - - ns tw2L Low period pulse width of SDEN 1 - - μs Data length: 24 bits Clock frequency: 5 MHz or less When 24 SCLK clock signals have been input during the high period of SDEN, the SDATA is taken in at the rising edge of SCLK. Note: If the number of SCLK clock signals during the high period of SDEN is 23 or less, SDATA is not taken in. If it is 25 or more, the register address is automatically incremented every time 1 byte is taken in. The slave address is assigned by the first byte, and the register address on the serial map is specified by the next byte. The third byte transfers the data to the address specified by the register address that was written by the second byte and if the data subsequently continues even after this, the register address is automatically incremented for the fourth and subsequent bytes. As a result, it is possible to send the data continuously from the specified addresses. Data of less than one byte is ignored. However, when the address reaches 2ch, the next byte to be transferred becomes 00h. Example of a write operation: SDATA 1 0 0 0 0 0 1 Slave address 0 0 0 0 0 1 1 1 DATA1 Register address 07h is set Data is written into address 07h. SDEN SDATA DATA2 Data is written into address 08h. DATA3 Data is written into address 09h. DATA Ignore if data is less than 1 byte. SDEN No.A1943-11/36 LV5236V 2) I2C serial transfer timing conditions twH SCL th1 twL th2 tbuf SDA th1 ts2 ts1 ton START condition tof ts3 Resend start condition STOP condition Input waveform condition Standard mode Parameter Symbol Conditions Min. Typ. Max. Unit SCL clock frequency fsc1 SCL clock frequency 0 - 100 kHz Data setup time ts1 SCL setup time relative to the fall of SDA 4.7 - - μs ts2 SDA setup time relative to the rise of SCL 250 - - ns ts3 SCL setup time relative to the rise of SDA 4.0 - - μs Data hold time th1 SCL hold time relative to the fall of SDA 4.0 - - μs th2 SDA hold time relative to the fall of SCL 0 - - μs Pulse width twL SCL pulse width for the L period 4.7 - - μs twH SCL pulse width for the H period 4.0 - - μs Input waveform ton SCL and SDA (input) rise time - - 1000 ns conditions tof SCL and SDA (input) fall time - - 300 ns Bus free time tbuf Time between STOP condition and START 4.7 - - μs Unit condition High-speed mode Parameter Symbol Conditions Min. Typ. Max. SCL clock frequency fsc1 SCL clock frequency 0 - 400 kHz Data setup time ts1 SCL setup time relative to the fall of SDA 0.6 - - μs ts2 SDA setup time relative to the rise of SCL 100 - - ns ts3 SCL setup time relative to the rise of SDA 0.6 - - μs th1 SCL hold time relative to the fall of SDA 0.6 - - μs th2 SDA hold time relative to the fall of SCL 0 - - μs Data hold time twL SCL pulse width for the L period 1.3 - - μs twH SCL pulse width for the H period 0.6 - - μs Input waveform ton SCL and SDA (input) rise time - - 300 ns conditions tof SCL and SDA (input) fall time - - 300 ns Bus free time tbuf Time between STOP and START conditions 1.3 - - μs Pulse width No.A1943-12/36 LV5236V I2C bus transfer method Start and stop conditions During data transfer operation using the I2C bus, SDA must basically be kept in constant state while SCL is “H” as shown below. SCL SDA ts2 th2 When data is not being transferred, both SCL and SDA are set in the “H” state. When SCL=SDA is “H,” the start condition is established when SDA is changed from “H” to “L,” and access is started. When SCL is “H,” the stop condition is established when SDA is changed from “L” to “H,” and access is ended. STOP condition START condition SCL SDA ts3 th1 Data transfer and acknowledgement response After the start condition has been established, the data is transferred one byte (8 bits) at a time. Any number of bytes of data can be transferred continuously. Each time the 8-bit data is transferred, the ACK signal is sent from the receive side to the send side. The ACK signal is issued when SDA on the send side is released and SDA on the receive side is set to “L” immediately after fall of the clock pulse at the SCL eighth bit of data transfer to “L.” When the next 1-byte transfer is left in the receive state after sending the ACK signal from the receive side, the receive side releases SDA at the fall of the SCL ninth clock. In the I2C bus, there is no CE signal. In its place, a 7-bit slave address is assigned to each device, and the first byte of transfer is assigned to the command (R/W) representing the 7-bit address and subsequent transfer direction. Note that only write is valid in this IC. The 7-bit address is transferred sequentially starting with MSB, and the eighth bit is set to “L” which indicates a write. Start M S B Slave address L S B W A C K M S B Register address L S B A C K M S B DATA L S B A C K Stop SCL SDA No.A1943-13/36 LV5236V Slave address condition SLAVE ADDRESS SA7 SA6 SA5 SA4 SA3 SA2 SA1 SA0 resister name - - A4 A3 A2 A1 A0 - default 1 0 0 0 0 0 0 - Terminal PIN A4 A3 A2 :LV5236 A1 A0 SA7 SA6 SA5 SA4 SA3 SA2 SA1 SA0 L L L L L 1 0 0 0 0 0 0 - L L L L H 1 0 0 0 0 0 1 - L L L H L 1 0 0 0 0 1 0 - L L L H H 1 0 0 0 0 1 1 - L L H L L 1 0 0 0 1 0 0 - L L H L H 1 0 0 0 1 0 1 - L L H H L 1 0 0 0 1 1 0 L L H H H 1 0 0 0 1 1 1 - L H L L L 1 0 0 1 0 0 0 - L H L L H 1 0 0 1 0 0 1 - L H L H L 1 0 0 1 0 1 0 - L H L H H 1 0 0 1 0 1 1 - L H H L L 1 0 0 1 1 0 0 - L H H L H 1 0 0 1 1 0 1 - L H H H L 1 0 0 1 1 1 0 L H H H H 1 0 0 1 1 1 1 - H L L L L 1 0 1 0 0 0 0 - H L L L H 1 0 1 0 0 0 1 - H L L H L 1 0 1 0 0 1 0 - H L L H H 1 0 1 0 0 1 1 - H L H L L 1 0 1 0 1 0 0 - H L H L H 1 0 1 0 1 0 1 - H L H H L 1 0 1 0 1 1 0 H L H H H 1 0 1 0 1 1 1 - H H L L L 1 0 1 1 0 0 0 - H H L L H 1 0 1 1 0 0 1 - H H L H L 1 0 1 1 0 1 0 - H H L H H 1 0 1 1 0 1 1 - H H H L L 1 0 1 1 1 0 0 - H H H L H 1 0 1 1 1 0 1 - H H H H L 1 0 1 1 1 1 0 - H H H H H 1 0 1 1 1 1 1 - No.A1943-14/36 LV5236V Serial each mode setting ADDRESS : 00h D7 D6 D5 D4 D3 D2 D1 register name - PWM[2] PWM[1] PWM[0] - - MAS - default 0 0 0 0 0 0 0 0 D6 D5 D4 time(ms) 0 0 0 0.5 0 0 1 1.0 0 1 0 2.0 0 1 1 4.0 1 0 0 8.0 - - - - - - - - - - - - - - - - D1 MAS 0 Master 1 Slave D0 PWM cycle setting *Default Master/Slave setting *Default ADDRESS : 01h D7 D6 D5 D4 D3 D2 D1 D0 register name - FOUT[2] FOUT[1] FOUT[0] - FIN[2] FIN[1] FIN[0] default 0 0 0 0 0 0 0 0 D6 D5 D4 time(ms) Fout slope setting 0 0 0 No slope *Default 0 0 1 0.5 0 1 0 1.0 0 1 1 2.0 1 0 0 4.0 1 0 1 8.0 1 1 0 16.0 1 1 1 32.0 Speed of fade a step (It takes 256 above-mentioned, set value × seconds until the fade is completed.) D2 D1 D0 time(ms) Fin slope setting 0 0 0 No slope *Default 0 0 1 0.5 0 1 0 1.0 0 1 1 2.0 1 0 0 4.0 1 0 1 8.0 1 1 0 16.0 1 1 1 32.0 Speed of fade a step (It takes 256 above-mentioned, set value × seconds until the fade is completed.) No.A1943-15/36 LV5236V ADDRESS : 02h D7 D6 D5 D4 D3 D2 D1 D0 register name - - - RLED[4] RLED[3] RLED[2] RLED[1] RLED[0] default 0 0 0 0 0 0 0 0 D4 D3 D2 D1 D0 Current value (mA) 0 0 0 0 0 0.96 0 0 0 0 1 1.92 0 0 0 1 0 2.88 0 0 0 1 1 3.84 0 0 1 0 0 4.80 0 0 1 0 1 5.76 0 0 1 1 0 6.72 0 0 1 1 1 7.68 0 1 0 0 0 8.64 0 1 0 0 1 9.60 0 1 0 1 0 10.56 0 1 0 1 1 11.52 0 1 1 0 0 12.48 0 1 1 0 1 13.44 0 1 1 1 0 14.40 0 1 1 1 1 15.36 1 0 0 0 0 16.32 1 0 0 0 1 17.28 1 0 0 1 0 18.24 1 0 0 1 1 19.20 1 0 1 0 0 20.16 1 0 1 0 1 21.12 1 0 1 1 0 22.08 1 0 1 1 1 23.04 1 1 0 0 0 24.00 1 1 0 0 1 24.96 1 1 0 1 0 25.92 1 1 0 1 1 26.88 1 1 1 0 0 27.84 1 1 1 0 1 28.80 1 1 1 1 0 29.76 1 1 1 1 1 30.72 RLED current value setting * Default No.A1943-16/36 LV5236V ADDRESS : 03h D7 D6 D5 D4 D3 D2 D1 D0 register name - - - GLED[4] GLED[3] GLED[2] GLED[1] GLED[0] default 0 0 0 0 0 0 0 0 D4 D3 D2 D1 D0 Current value (mA) 0 0 0 0 0 0.96 0 0 0 0 1 1.92 0 0 0 1 0 2.88 0 0 0 1 1 3.84 0 0 1 0 0 4.80 0 0 1 0 1 5.76 0 0 1 1 0 6.72 0 0 1 1 1 7.68 0 1 0 0 0 8.64 0 1 0 0 1 9.60 0 1 0 1 0 10.56 0 1 0 1 1 11.52 0 1 1 0 0 12.48 0 1 1 0 1 13.44 0 1 1 1 0 14.40 0 1 1 1 1 15.36 1 0 0 0 0 16.32 1 0 0 0 1 17.28 1 0 0 1 0 18.24 1 0 0 1 1 19.20 1 0 1 0 0 20.16 1 0 1 0 1 21.12 1 0 1 1 0 22.08 1 0 1 1 1 23.04 1 1 0 0 0 24.00 1 1 0 0 1 24.96 1 1 0 1 0 25.92 1 1 0 1 1 26.88 1 1 1 0 0 27.84 1 1 1 0 1 28.80 1 1 1 1 0 29.76 1 1 1 1 1 30.72 GLED current value setting * Default No.A1943-17/36 LV5236V ADDRESS : 04h D7 D6 D5 D4 D3 D2 D1 D0 register name - - - BLED[4] BLED[3] BLED[2] BLED[1] BLED[0] default 0 0 0 0 0 0 0 0 D4 D3 D2 D1 D0 Current value (mA) 0 0 0 0 0 0.96 0 0 0 0 1 1.92 0 0 0 1 0 2.88 0 0 0 1 1 3.84 0 0 1 0 0 4.80 0 0 1 0 1 5.76 0 0 1 1 0 6.72 0 0 1 1 1 7.68 0 1 0 0 0 8.64 0 1 0 0 1 9.60 0 1 0 1 0 10.56 0 1 0 1 1 11.52 0 1 1 0 0 12.48 0 1 1 0 1 13.44 0 1 1 1 0 14.40 0 1 1 1 1 15.36 1 0 0 0 0 16.32 1 0 0 0 1 17.28 1 0 0 1 0 18.24 1 0 0 1 1 19.20 1 0 1 0 0 20.16 1 0 1 0 1 21.12 1 0 1 1 0 22.08 1 0 1 1 1 23.04 1 1 0 0 0 24.00 1 1 0 0 1 24.96 1 1 0 1 0 25.92 1 1 0 1 1 26.88 1 1 1 0 0 27.84 1 1 1 0 1 28.80 1 1 1 1 0 29.76 1 1 1 1 1 30.72 BLED current value setting * Default No.A1943-18/36 LV5236V ADDRESS : 05h D7 D6 D5 D4 D3 D2 D1 D0 register name - B2ON G2ON R2ON - B1ON G1ON R1ON default 0 0 0 0 0 0 0 0 D6 B2ON 0 OFF 1 ON D5 G2ON 0 OFF 1 ON D4 R2ON 0 OFF 1 ON D2 B1ON 0 OFF 1 ON D1 G1ON 0 OFF 1 ON D0 R1ON 0 OFF 1 ON LEDB2 ON/OFF setting * Default LEDG2 ON/OFF setting * Default LEDR2 ON/OFF setting * Default LEDB1 ON/OFF setting * Default LEDG1ON/OFF setting * Default LEDR1 ON/OFF setting * Default ADDRESS : 06h D7 D6 D5 D4 D3 D2 D1 D0 register name - B4ON G4ON R4ON - B3ON G3ON R3ON default 0 0 0 0 0 0 0 0 D6 B4ON 0 OFF 1 ON D5 G4ON 0 OFF 1 ON D4 R4ON 0 OFF 1 ON D2 B3ON 0 OFF 1 ON D1 G3ON 0 OFF 1 ON D0 R3ON 0 OFF 1 ON LEDB4 ON/OFF setting * Default LEDG4 ON/OFF setting * Default LEDR4 ON/OFF setting * Default LEDB3 ON/OFF setting * Default LEDG3 ON/OFF setting * Default LEDR3 ON/OFF setting * Default No.A1943-19/36 LV5236V ADDRESS : 07h D7 D6 D5 D4 D3 D2 D1 D0 register name - B6ON G6ON R6ON - B5ON G5ON R5ON default 0 0 0 0 0 0 0 0 D6 B6ON 0 OFF 1 ON D5 G6ON 0 OFF 1 ON D4 R6ON 0 OFF 1 ON D2 B5ON 0 OFF 1 ON D1 G5ON 0 OFF 1 ON D0 R5ON 0 OFF 1 ON LEDB6 ON/OFF setting * Default LEDG6 ON/OFF setting * Default LEDR6 ON/OFF setting * Default LEDB5 ON/OFF setting * Default LEDG5 ON/OFF setting * Default LEDR5 ON/OFF setting * Default ADDRESS : 08h D7 D6 D5 D4 D3 D2 D1 D0 register name - B8ON G8ON R8ON - B7ON G7ON R7ON default 0 0 0 0 0 0 0 0 D6 B8ON 0 OFF 1 ON D5 G8ON 0 OFF 1 ON D4 R8ON 0 OFF 1 ON D2 B7ON 0 OFF 1 ON D1 G7ON 0 OFF 1 ON D0 R7ON 0 OFF 1 ON LEDB8 ON/OFF setting * Default LEDG8 ON/OFF setting * Default LEDR8 ON/OFF setting * Default LEDB7 ON/OFF setting * Default LEDG7 ON/OFF setting * Default LEDR7 ON/OFF setting * Default No.A1943-20/36 LV5236V ADDRESS : 09h D7 D6 D5 D4 D3 D2 D1 D0 register name R7PON[1] R7PON[0] R5PON[1] R5PON[0] R3PON[1] R3PN[0] R1PON[1] R1PON[0] default 0 0 0 0 0 0 0 0 D7 D6 R5PON 0 0 PMW output priority LEDR7 output setting 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D5 D4 R5PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D3 D2 R3PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D1 D0 R1PON 0 0 PMW output priority * Default LEDR5 output setting * Default LEDR3 output setting * Default LEDR1 output setting * Default 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - ADDRESS : 0ah D7 D6 D5 D4 D3 D2 D1 D0 register name R8PON[1] R8PON[0] R6PON[1] R6PON[0] R4PON[1] R4PON[0] R2PON[1] R2PON[0] default 0 0 0 0 0 0 0 0 D7 D6 R8PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D5 D4 R6PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D3 D2 R4PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D1 D0 R2PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - LEDR8 output setting * Default LEDR6 output setting * Default LEDR4 output setting * Default LEDR2 output setting * Default No.A1943-21/36 LV5236V ADDRESS : 0bh D7 D6 D5 D4 D3 D2 D1 D0 register name G7PON[1] G7PON[0] G5PON[1] G5PON[0] G3PON[1] G3PON[0] G1PON[1] G1PON[0] default 0 0 0 0 0 0 0 0 D7 D6 G7PON 0 0 PMW output priority LEDG7 output setting * Default 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D5 D4 G5PON 0 0 PMW output priority LEDG5 output setting * Default 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D3 D2 G3PON 0 0 PMW output priority LEDG3 output setting * Default 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D1 D0 G1PON 0 0 PMW output priority LEDG1 output setting * Default 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - ADDRESS : 0ch D7 D6 D5 D4 D3 D2 D1 D0 register name G8PON[1] G8PON[0] G6PON[1] G6PON[0] G4PON[1] G4PON[0] G2PON[1] G2PON[0] default 0 0 0 0 0 0 0 0 D7 D6 G8PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D5 D4 G6PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D3 D2 G4PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D1 D0 G2PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - LEDG8 output setting * Default LEDG6 output setting * Default LEDG4 output setting * Default LEDG2 output setting * Default No.A1943-22/36 LV5236V ADDRESS : 0dh D7 D6 D5 D4 D3 D2 D1 D0 register name B7PON[1] B7PON[0] B5PON[1] B5PON[0] B3PON[1] B3PON[0] B1PON[1] B1PON[0] default 0 0 0 0 0 0 0 0 D7 D6 B7PON 0 0 PMW output priority LEDB7 output setting * Default 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D5 D4 B5PON 0 0 PMW output priority LEDB5 output setting * Default 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D3 D2 B3PON 0 0 PMW output priority LEDB3 output setting * Default 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D1 D0 B1PON 0 0 PMW output priority LEDB1 output setting * Default 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - ADDRESS : 0eh D7 D6 D5 D4 D3 D2 D1 D0 register name B8PON[1] B8PON[0] B6PON[1] B6PON[0] B4PON[1] B4PON[0] B2PON[1] B2PON[0] default 0 0 0 0 0 0 0 0 D7 D6 B8PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D5 D4 B6PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D3 D2 B4PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - D1 D0 B2PON 0 0 PMW output priority 0 1 Fade output priority 1 0 Compulsion ON/OFF output priority - - - LEDB8 output setting * Default LEDB6 output setting * Default LEDB4 output setting * Default LEDB2 output setting * Default No.A1943-23/36 LV5236V ADDRESS : 0fh D7 D6 D5 D4 D3 D2 D1 D0 register name R8FD R7FD R6FD R5FD R4FD R3FD R2FD R1FD default 0 0 0 0 0 0 0 0 D7 R8FD 0 Fade invalidity 1 Fade effective D6 R7FD 0 Fade invalidity 1 Fade effective D5 R6FD 0 Fade invalidity 1 Fade effective D4 R5FD 0 Fade invalidity 1 Fade effective D3 R4FD 0 Fade invalidity 1 Fade effective D2 R3FD 0 Fade invalidity 1 Fade effective D1 R2FD 0 Fade invalidity 1 Fade effective D0 R1FD 0 Fade invalidity 1 Fade effective LEDR8 fade function ON/OFF setting * Default LEDR7 fade function ON/OFF setting * Default LEDR6 fade function ON/OFF setting * Default LEDR5 fade function ON/OFF setting * Default LEDR4 fade function ON/OFF setting * Default LEDR3 fade function ON/OFF setting * Default LEDR2 fade function ON/OFF setting * Default LEDR1 fade function ON/OFF setting * Default No.A1943-24/36 LV5236V ADDRESS : 10h D7 D6 D5 D4 D3 D2 D1 D0 register name G8FD G7FD G6FD G5FD G4FD G3FD G2FD G1FD default 0 0 0 0 0 0 0 0 D7 G8FD 0 Fade invalidity 1 Fade effective D6 G7FD 0 Fade invalidity 1 Fade effective D5 G6FD 0 Fade invalidity 1 Fade effective D4 G5FD 0 Fade invalidity 1 Fade effective D3 G4FD 0 Fade invalidity 1 Fade effective D2 G3FD 0 Fade invalidity 1 Fade effective D1 G2FD 0 Fade invalidity 1 Fade effective D0 G1FD 0 Fade invalidity 1 Fade effective LEDG8 fade function ON/OFF setting * Default LEDG7 fade function ON/OFF setting * Default LEDG6 fade function ON/OFF setting * Default LEDG5 fade function ON/OFF setting * Default LEDG4 fade function ON/OFF setting * Default LEDG3 fade function ON/OFF setting * Default LEDG2 fade function ON/OFF setting * Default LEDG1 fade function ON/OFF setting * Default No.A1943-25/36 LV5236V ADDRESS : 11h D7 D6 D5 D4 D3 D2 D1 D0 register name B8FD B7FD B6FD B5FD B4FD B3FD B2FD B1FD default 0 0 0 0 0 0 0 0 D7 B8FD 0 Fade invalidity 1 Fade effective D6 B7FD 0 Fade invalidity 1 Fade effective D5 B6FD 0 Fade invalidity 1 Fade effective D4 B5FD 0 Fade invalidity 1 Fade effective D3 B4FD 0 Fade invalidity 1 Fade effective D2 B3FD 0 Fade invalidity 1 Fade effective D1 B2FD 0 Fade invalidity 1 Fade effective D0 B1FD 0 Fade invalidity 1 Fade effective LEDB8 fade function ON/OFF setting * Default LEDB7 fade function ON/OFF setting * Default LEDB6 fade function ON/OFF setting * Default LEDB5 fade function ON/OFF setting * Default LEDB4 fade function ON/OFF setting * Default LEDB3 fade function ON/OFF setting * Default LEDB2 fade function ON/OFF setting * Default LEDB1 fade function ON/OFF setting * Default No.A1943-26/36 LV5236V ADDRESS : 12h D7 D6 D5 D4 D3 D2 D1 D0 register name R8CM R7CM R6CM R5CM R4CM R3CM R2CM R1CM default 0 0 0 0 0 0 0 0 D7 R8CM 0 Compulsion OFF 1 Compulsion ON D6 R7CM 0 Compulsion OFF 1 Compulsion ON D5 R6CM 0 Compulsion OFF 1 Compulsion ON D4 R5CM 0 Compulsion OFF 1 Compulsion ON D3 R4CM 0 Compulsion OFF 1 Compulsion ON D2 R3CM 0 Compulsion OFF 1 Compulsion ON D1 R2CM 0 Compulsion OFF 1 Compulsion ON D0 R1CM 0 Compulsion OFF 1 Compulsion ON LEDR8 compulsion ON/OFF setting * Default LEDR7 compulsion ON/OFF setting * Default LEDR6 compulsion ON/OFF setting * Default LEDR5 compulsion ON/OFF setting * Default LEDR4 compulsion ON/OFF setting * Default LEDR3 fade function ON/OFF setting * Default LEDR2 fade function ON/OFF setting * Default LEDR1 fade function ON/OFF setting * Default No.A1943-27/36 LV5236V ADDRESS : 13h D7 D6 D5 D4 D3 D2 D1 D0 register name G8CM G7CM G6CM G5CM G4CM G3CM G2CM G1CM default 0 0 0 0 0 0 0 0 D7 G8CM 0 Compulsion OFF 1 Compulsion ON D6 G7CM 0 Compulsion OFF 1 Compulsion ON D5 G6CM 0 Compulsion OFF 1 Compulsion ON D4 G5CM 0 Compulsion OFF 1 Compulsion ON D3 G4CM 0 Compulsion OFF 1 Compulsion ON D2 G3CM 0 Compulsion OFF 1 Compulsion ON D1 G2CM 0 Compulsion OFF 1 Compulsion ON D0 G1CM 0 Compulsion OFF 1 Compulsion ON LEDG8 compulsion ON/OFF setting * Default LEDG7 compulsion ON/OFF setting * Default LEDG6 compulsion ON/OFF setting * Default LEDG5 compulsion ON/OFF setting * Default LEDG4 compulsion ON/OFF setting * Default LEDG3 fade function ON/OFF setting * Default LEDG2 fade function ON/OFF setting * Default LEDG1 fade function ON/OFF setting * Default No.A1943-28/36 LV5236V ADDRESS : 14h D7 D6 D5 D4 D3 D2 D1 D0 register name B8CM B7CM B6CM B5CM B4CM B3CM B2CM B1CM default 0 0 0 0 0 0 0 0 D7 B8CM 0 Compulsion OFF 1 Compulsion ON D6 B7CM 0 Compulsion OFF 1 Compulsion ON D5 B6CM 0 Compulsion OFF 1 Compulsion ON D4 B5CM 0 Compulsion OFF 1 Compulsion ON D3 B4CM 0 Compulsion OFF 1 Compulsion ON D2 B3CM 0 Compulsion OFF 1 Compulsion ON D1 B2CM 0 Compulsion OFF 1 Compulsion ON D0 B1CM 0 Compulsion OFF 1 Compulsion ON LEDB8 compulsion ON/OFF setting * Default LEDB7 compulsion ON/OFF setting * Default LEDB6 compulsion ON/OFF setting * Default LEDB5 compulsion ON/OFF setting * Default LEDB4 compulsion ON/OFF setting * Default LEDB3 fade function ON/OFF setting * Default LEDB2 fade function ON/OFF setting * Default LEDB1 fade function ON/OFF setting * Default No.A1943-29/36 LV5236V ADDRESS : 15h D7 D6 D5 D4 D3 D2 D1 D0 register name R1PWM[7] R1PWM[6] R1PWM[5] R1PWM[4] R1PWM[3] R1PWM[2] R1PWM[1] R1PWM[0] default 0 0 0 0 0 0 0 0 LEDR1 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R1PWM[7:0] 256 ADDRESS : 16h D7 D6 D5 D4 D3 D2 D1 D0 register name G1PWM[7] G1PWM[6] G1PWM[5] G1PWM[4] G1PWM[3] G1PWM[2] G1PWM[1] G1PWM[0] default 0 0 0 0 0 0 0 0 LEDG1 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G1PWM[7:0] 256 ADDRESS : 17h D7 D6 D5 D4 D3 D2 D1 D0 register name B1PWM[7] B1PWM[6] B1PWM[5] B1PWM[4] B1PWM[3] B1PWM[2] B1PWM[1] B1PWM[0] default 0 0 0 0 0 0 0 0 LEDB1 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B1PWM[7:0] 256 ADDRESS : 18h D7 D6 D5 D4 D3 D2 D1 D0 register name R2PWM[7] R2PWM[6] R2PWM[5] R2PWM[4] R2PWM[3] R2PWM[2] R2PWM[1] R2PWM[0] default 0 0 0 0 0 0 0 0 LEDR2 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R2PWM[7:0] 256 ADDRESS : 19h D7 D6 D5 D4 D3 D2 D1 D0 register name G2PWM[7] G2PWM[6] G2PWM[5] G2PWM[4] G2PWM[3] G2PWM[2] G2PWM[1] G2PWM[0] default 0 0 0 0 0 0 0 0 LEDG2 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G2PWM[7:0] 256 ADDRESS : 1ah D7 D6 D5 D4 D3 D2 D1 D0 register name B2PWM[7] B2PWM[6] B2PWM[5] B2PWM[4] B2PWM[3] B2PWM[2] B2PWM[1] B2PWM[0] default 0 0 0 0 0 0 0 0 LEDB2 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B2PWM[7:0] 256 No.A1943-30/36 LV5236V ADDRESS : 1bh D7 D6 D5 D4 D3 D2 D1 D0 register name R3PWM[7] R3PWM[6] R3PWM[5] R3PWM[4] R3PWM[3] R3PWM[2] R3PWM[1] R3PWM[0] default 0 0 0 0 0 0 0 0 LEDR3 PWM Duty setting (DefaultALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R3PWM[7:0] 256 ADDRESS : 1ch D7 D6 D5 D4 D3 D2 D1 D0 register name G3PWM[7] G3PWM[6] G3PWM[5] G3PWM[4] G3PWM[3] G3PWM[2] G3PWM[1] G3PWM[0] default 0 0 0 0 0 0 0 0 LEDG3 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G3PWM[7:0] 256 ADDRESS : 1dh D7 D6 D5 D4 D3 D2 D1 D0 register name B3PWM[7] B3PWM[6] B3PWM[5] B3PWM[4] B3PWM[3] B3PWM[2] B3PWM[1] B3PWM[0] default 0 0 0 0 0 0 0 0 LEDB3 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B3PWM[7:0] 256 ADDRESS : 1eh D7 D6 D5 D4 D3 D2 D1 D0 register name R4PWM[7] R4PWM[6] R4PWM[5] R4PWM[4] R4PWM[3] R4PWM[2] R4PWM[1] R4PWM[0] default 0 0 0 0 0 0 0 0 LEDR4 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R4PWM[7:0] 256 ADDRESS : 1fh D7 D6 D5 D4 D3 D2 D1 D0 register name G4PWM[7] G4PWM[6] G4PWM[5] G4PWM[4] G4PWM[3] G4PWM[2] G4PWM[1] G4PWM[0] default 0 0 0 0 0 0 0 0 LEDG4 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G4PWM[7:0] 256 ADDRESS : 20h D7 D6 D5 D4 D3 D2 D1 D0 register name B4PWM[7] B4PWM[6] B4PWM[5] B4PWM[4] B4PWM[3] B4PWM[2] B4PWM[1] B4PWM[0] default 0 0 0 0 0 0 0 0 LEDB4 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B4PWM[7:0] 256 No.A1943-31/36 LV5236V ADDRESS : 21h D7 D6 D5 D4 D3 D2 D1 D0 register name R5PWM[7] R5PWM[6] R5PWM[5] R5PWM[4] R5PWM[3] R5PWM[2] R5PWM[1] R5PWM[0] default 0 0 0 0 0 0 0 0 LEDR5 PWM Duty setting (DefaultALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R5PWM[7:0] 256 ADDRESS : 22h D7 D6 D5 D4 D3 D2 D1 D0 register name G5PWM[7] G5PWM[6] G5PWM[5] G5PWM[4] G5PWM[3] G5PWM[2] G5PWM[1] G5PWM[0] default 0 0 0 0 0 0 0 0 LEDG5 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G5PWM[7:0] 256 ADDRESS : 23h D7 D6 D5 D4 D3 D2 D1 D0 register name B5PWM[7] B5PWM[6] B5PWM[5] B5PWM[4] B5PWM[3] B5PWM[2] B5PWM[1] B5PWM[0] default 0 0 0 0 0 0 0 0 LEDB5 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B5PWM[7:0] 256 ADDRESS : 24h D7 D6 D5 D4 D3 D2 D1 D0 register name R6PWM[7] R6PWM[6] R6PWM[5] R6PWM[4] R6PWM[3] R6PWM[2] R6PWM[1] R6PWM[0] default 0 0 0 0 0 0 0 0 LEDR6 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R6PWM[7:0] 256 ADDRESS : 25h D7 D6 D5 D4 D3 D2 D1 D0 register name G6PWM[7] G6PWM[6] G6PWM[5] G6PWM[4] G6PWM[3] G6PWM[2] G6PWM[1] G6PWM[0] default 0 0 0 0 0 0 0 0 LEDG6 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G6PWM[7:0] 256 ADDRESS : 26h D7 D6 D5 D4 D3 D2 D1 D0 register name B6PWM[7] B6PWM[6] B6PWM[5] B6PWM[4] B6PWM[3] B6PWM[2] B6PWM[1] B6PWM[0] default 0 0 0 0 0 0 0 0 LEDB6 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B6PWM[7:0] 256 No.A1943-32/36 LV5236V ADDRESS : 27h D7 D6 D5 D4 D3 D2 D1 D0 register name R7PWM[7] R7PWM[6] R7PWM[5] R7PWM[4] R7PWM[3] R7PWM[2] R7PWM[1] R7PWM[0] default 0 0 0 0 0 0 0 0 LEDR7 PWM Duty setting (DefaultALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R7PWM[7:0] 256 ADDRESS : 28h D7 D6 D5 D4 D3 D2 D1 D0 register name G7PWM[7] G7PWM[6] G7PWM[5] G7PWM[4] G7PWM[3] G7PWM[2] G7PWM[1] G7PWM[0] default 0 0 0 0 0 0 0 0 LEDG7 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G7PWM[7:0] 256 ADDRESS : 29h D7 D6 D5 D4 D3 D2 D1 D0 register name B7PWM[7] B7PWM[6] B7PWM[5] B7PWM[4] B7PWM[3] B7PWM[2] B7PWM[1] B7PWM[0] default 0 0 0 0 0 0 0 0 LEDB7 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B7PWM[7:0] 256 ADDRESS : 2ah D7 D6 D5 D4 D3 D2 D1 D0 register name R8PWM[7] R8PWM[6] R8PWM[5] R8PWM[4] R8PWM[3] R8PWM[2] R8PWM[1] R8PWM[0] default 0 0 0 0 0 0 0 0 LEDR8 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = R8PWM[7:0] 256 ADDRESS : 2bh D7 D6 D5 D4 D3 D2 D1 D0 register name G8PWM[7] G8PWM[6] G8PWM[5] G8PWM[4] G8PWM[3] G8PWM[2] G8PWM[1] G8PWM[0] default 0 0 0 0 0 0 0 0 LEDG8 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = G8PWM[7:0] 256 ADDRESS : 2ch D7 D6 D5 D4 D3 D2 D1 D0 register name B8PWM[7] B8PWM[6] B8PWM[5] B8PWM[4] B8PWM[3] B8PWM[2] B8PWM[1] B8PWM[0] default 0 0 0 0 0 0 0 0 LEDB8 PWM Duty setting (Default ALL0) D Duty (%) 00h 0.0 ffh 99.6 Duty (%) = B8PWM[7:0] 256 No.A1943-33/36 LV5236V LV5236V serial map • Table upper row: Register name A7 00h 0 A6 0 A5 0 A4 0 A3 Table the lower: Default value A2 0 0 A1 0 A0 0 01h 0 0 0 0 0 0 0 1 02h 0 0 0 0 0 0 1 0 03h 04h 0 0 0 0 0 0 0 0 0 0 0 1 1 0 1 0 05h 0 0 0 0 0 1 0 1 06h 0 0 0 0 0 1 1 0 07h 08h 0 0 0 0 0 0 0 0 0 1 1 0 1 0 1 0 09h 0 0 0 0 1 0 0 1 0ah 0 0 0 0 1 0 1 0 0bh 0ch 0 0 0 0 0 0 0 0 1 1 0 1 1 0 1 0 0dh 0 0 0 0 1 1 0 1 0eh 0 0 0 0 1 1 1 0 0fh 10h 0 0 0 0 0 0 0 1 1 0 1 0 1 0 1 0 11h 0 0 0 1 0 0 0 1 12h 0 0 0 1 0 0 1 0 13h 14h 0 0 0 0 0 0 1 1 0 0 0 1 1 0 1 0 15h 0 0 0 1 0 1 0 1 16h 0 0 0 1 0 1 1 0 17h 18h 0 0 0 0 0 0 1 1 0 1 1 0 1 0 1 0 19h 0 0 0 1 1 0 0 1 1ah 0 0 0 1 1 0 1 0 Register address D7 D6 × 0 D5 D4 PWM[2:0] 0 × 0 0 0 0 × × × 0 0 0 × × × 0 0 0 × × × D2 D1 D0 × × MAS × 0 0 0 0 × FOUT[2:0] 0 D3 0 0 0 0 FIN[2:0] 0 0 0 0 0 0 0 RLED[4:0] 0 GLED[4:0] 0 0 0 BLED[4:0] 0 0 0 0 0 0 0 0 × B2ON G2ON R2ON × B1ON G1ON R1ON 0 0 0 0 0 0 0 0 × B4ON G4ON R4ON × B3ON G3ON R3ON 0 0 0 0 0 0 0 0 × B6ON G6ON R6ON × B5ON G5ON R5ON 0 0 0 0 0 0 0 0 × B8ON G8ON R8ON × B7ON G7ON R7ON 0 0 0 0 0 0 0 0 R7PON[1:0] R5PON[1:0] R3PON[1:0] R1PON[2:0] 0 0 0 0 0 0 0 0 R8PON[1:0] R6PON[1:0] R4PON[1:0] R2PON[1:0] 0 0 0 0 0 G7PON[1:0] 0 0 0 G5PON[1:0] 0 0 G3PON[1:0] 0 0 0 0 G1PON[1:0] 0 0 G8PON[1:0] G6PON[1:0] G4PON[1:0] G2PON[1:0] 0 0 0 0 0 0 0 0 B7PON[1:0] B5PON[1:0] B3PON[1:0] B1PON[1:0] 0 0 0 0 0 0 0 0 B8PON[1:0] B6PON[1:0] B4PON[1:0] B2PON[1:0] 0 0 0 0 0 0 0 0 R8FD R7FD R6FD R5FD R4FD R3FD R2FD R1FD 0 0 0 0 0 0 0 0 G8FD G7FD G6FD G5FD G4FD G3FD G2FD G1FD 0 0 0 0 0 0 0 0 B8FD B7FD B6FD B5FD B4FD B3FD B2FD B1FD 0 0 0 0 0 0 0 0 R8CM R7CM R6CM R5CM R4CM R3CM R2CM R1CM 0 0 0 0 0 0 0 0 G8CM G7CM G6CM G5CM G4CM G3CM G2CM G1CM 0 0 0 0 0 0 0 0 B8CM B7CM B6CM B5CM B4CM B3CM B2CM B1CM 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R1PWM[7:0] 0 0 0 0 0 0 0 0 G1PWM[7:0] 0 0 B1PWM[7:0] 0 0 0 0 0 R2PWM[7:0] 0 0 0 0 0 G2PWM[7:0] 0 0 0 0 0 0 0 0 B2PWM[7:0] 0 0 Data Continued on next page. No.A1943-34/36 LV5236V Continued from preceding page. A7 1bh 1ch 1dh 1eh 1fh 20h 21h 22h 23h 24h 25h 26h 27h 28h 29h 2ah 2bh 2ch 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 A6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 A5 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 A4 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 A3 A2 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 Register address 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 A1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 A0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R3PWM[7:0] 0 0 0 0 0 G3PWM[7:0] 0 0 0 0 0 B3PWM[7:0] 0 0 0 0 0 R4PWM[7:0] 0 0 0 0 0 G4PWM[7:0] 0 0 0 0 0 B4PWM[7:0] 0 0 0 0 0 R5PWM[7:0] 0 0 0 0 0 G5PWM[7:0] 0 0 0 0 0 B5PWM[7:0] 0 0 0 0 0 R6PWM[7:0] 0 0 0 0 0 G6PWM[7:0] 0 0 0 0 0 B6PWM[7:0] 0 0 0 0 0 R7PWM[7:0] 0 0 0 0 0 G7PWM[7:0] 0 0 0 0 0 B7PWM[7:0] 0 0 0 0 0 R8PWM[7:0] 0 0 0 0 0 G8PWM[7:0] 0 0 0 0 0 B8PWM[7:0] 0 0 0 0 0 Data No.A0000-35/36 LV5236V ORDERING INFORMATION Device LV5236V-MPB-H Package SSOP44J (275mil) (Pb-Free / Halogen Free) Shipping (Qty / Packing) LV5236V-TLM-H SSOP44J (275mil) (Pb-Free / Halogen Free) 2000 / Tape & Reel LV5236VZ-MPB-H SSOP44J (275mil) (Pb-Free / Halogen Free) 30 / Fan-Fold LV5236VZ-TLM-H SSOP44J (275mil) (Pb-Free / Halogen Free) 2000 / Tape & Reel 30 / Fan-Fold ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A1943-36/36