CAT93C46 D

CAT93C46
1 Kb Microwire Serial
EEPROM
Description
The CAT93C46 is a 1 Kb Serial EEPROM memory device which is
configured as either 64 registers of 16 bits (ORG pin at VCC) or 128
registers of 8 bits (ORG pin at GND). Each register can be written (or
read) serially by using the DI (or DO) pin. The CAT93C46 features a
self−timed internal write with auto−clear. On−chip Power−On Reset
circuit protects the internal logic against powering up in the wrong
state.
http://onsemi.com
PDIP−8
L SUFFIX
CASE 646AA
Features
•
•
•
•
•
•
•
•
•
•
•
•
High Speed Operation: 2 MHz
1.8 V to 5.5 V Supply Voltage Range
Selectable x8 or x16 Memory Organization
Self−Timed Write Cycle with Auto−Clear
Software Write Protection
Power−up Inadvertant Write Protection
Low Power CMOS Technology
1,000,000 Program/Erase Cycles
100 Year Data Retention
Industrial Temperature Range
8−pin PDIP, SOIC, TSSOP and 8−pad TDFN Packages
This Device is Pb−Free, Halogen Free/BFR Free and RoHS
Compliant*
SOIC−8
V, W SUFFIX
CASE 751BD
TSSOP−8
Y SUFFIX
CASE 948AL
SOIC−8
X SUFFIX
CASE 751BE
TDFN−8*
VP2 SUFFIX
CASE 511AK
PIN CONFIGURATIONS
CS
SK
DI
DO
1
VCC
NC
NC
VCC
ORG CS
SK
GND
1
ORG
GND
DO
DI
SOIC (W)
(Top View)
PDIP (L), SOIC (V, X),
TSSOP (Y), TDFN (VP2)*
(Top View)
VCC
PIN FUNCTION
Pin Name
ORG
CS
SK
CAT93C46
DO
DI
GND
Figure 1. Functional Symbol
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
Function
CS
Chip Select
SK
Clock Input
DI
Serial Data Input
DO
Serial Data Output
VCC
Power Supply
GND
Ground
ORG
Memory Organization
NC
No Connection
Note: When the ORG pin is connected to VCC, the
x16 organization is selected. When it is connected
to ground, the x8 organization is selected. If the
ORG pin is left unconnected, then an internal pullup
device will select the x16 organization.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 13 of this data sheet.
* Not Recommended for New Designs
© Semiconductor Components Industries, LLC, 2013
October, 2013 − Rev. 10
1
Publication Order Number:
CAT93C46/D
CAT93C46
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameter
Value
Units
Storage Temperature
−65 to +150
°C
Voltage on Any Pin with Respect to Ground (Note 1)
−0.5 to +6.5
V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. The DC input voltage on any pin should not be lower than −0.5 V or higher than VCC + 0.5 V. During transitions, the voltage on any pin may
undershoot to no less than −1.5 V or overshoot to no more than VCC + 1.5 V, for periods of less than 20 ns.
Table 2. RELIABILITY CHARACTERISTICS (Note 2)
Parameter
Symbol
NEND (Note 3)
TDR
Endurance
Min
Units
1,000,000
Program / Erase Cycles
100
Years
Data Retention
2. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100
and JEDEC test methods.
3. Block Mode, VCC = 5 V, 25°C
Table 3. D.C. OPERATING CHARACTERISTICS (VCC = +1.8 V to +5.5 V, TA = −40°C to +85°C, unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min
Max
Units
ICC1
Power Supply Current (Write)
fSK = 1 MHz
VCC = 5.0 V
1
mA
ICC2
Power Supply Current (Read)
fSK = 1 MHz
VCC = 5.0 V
500
mA
ISB1
Power Supply Current (Standby) (x8 Mode)
VIN = GND or VCC,
CS = GND
ORG = GND
2
mA
ISB2
Power Supply Current (Standby) (x16Mode)
VIN = GND or VCC,
CS = GND
ORG = Float or VCC
1
mA
VIN = GND to VCC
1
mA
1
mA
ILI
Input Leakage Current
ILO
Output Leakage Current
VOUT = GND to VCC,
CS = GND
VIL1
Input Low Voltage
4.5 V v VCC < 5.5 V
−0.1
0.8
V
VIH1
Input High Voltage
4.5 V v VCC < 5.5 V
2
VCC + 1
V
VIL2
Input Low Voltage
1.8 V v VCC < 4.5 V
0
VCC x 0.2
V
VIH2
Input High Voltage
1.8 V v VCC < 4.5 V
VCC x 0.7
VCC + 1
V
VOL1
Output Low Voltage
4.5 V v VCC < 5.5 V
IOL = 2.1 mA
0.4
V
VOH1
Output High Voltage
4.5 V v VCC < 5.5 V
IOH = −400 mA
VOL2
Output Low Voltage
1.8 V v VCC < 4.5 V
IOL = 1 mA
VOH2
Output High Voltage
1.8 V v VCC < 4.5 V
IOH = −100 mA
http://onsemi.com
2
2.4
V
0.2
VCC − 0.2
V
V
CAT93C46
Table 4. PIN CAPACITANCE (TA = 25°C, f = 1 MHz, VCC = 5 V)
Test
Symbol
COUT (Note 4)
CIN (Note 4)
Conditions
Output Capacitance (DO)
Input Capacitance (CS, SK, DI, ORG)
Min
Typ
Max
Units
VOUT = 0 V
5
pF
VIN = 0 V
5
pF
4. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100
and JEDEC test methods.
Table 5. A.C. CHARACTERISTICS (VCC = +1.8 V to +5.5 V, TA = −40°C to +85°C, unless otherwise specified.) (Note 5)
Limits
Min
Parameter
Symbol
Max
Units
tCSS
CS Setup Time
50
ns
tCSH
CS Hold Time
0
ns
tDIS
DI Setup Time
100
ns
tDIH
DI Hold Time
100
ns
tPD1
Output Delay to 1
0.25
tPD0
ms
Output Delay to 0
0.25
ms
tHZ (Note 6)
Output Delay to High−Z
100
ns
tEW (Note 7)
Program/Erase Pulse Width
5
ms
tCSMIN
Minimum CS Low Time
0.25
ms
tSKHI
Minimum SK High Time
0.25
ms
tSKLOW
Minimum SK Low Time
0.25
ms
tSV
Output Delay to Status Valid
SKMAX
Maximum Clock Frequency
DC
0.25
ms
2000
kHz
5. Test conditions according to “AC Test Conditions” table.
6. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100
and JEDEC test methods.
7. tEW is 10 ms max for ERAL and WRAL operations.
Table 6. POWER−UP TIMING (Notes 8 and 9)
Parameter
Symbol
Max
Units
tPUR
Power−up to Read Operation
1
ms
tPUW
Power−up to Write Operation
1
ms
8. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100
and JEDEC test methods.
9. tPUR and tPUW are the delays required from the time VCC is stable until the specified operation can be initiated.
Table 7. A.C. TEST CONDITIONS
Input Rise and Fall Times
v 50 ns
Input Pulse Voltages
0.4 V to 2.4 V
4.5 V v VCC v 5.5 V
0.8 V, 2.0 V
4.5 V v VCC v 5.5 V
0.2 VCC to 0.7 VCC
1.8 V v VCC v 4.5 V
0.5 VCC
1.8 V v VCC v 4.5 V
Timing Reference Voltages
Input Pulse Voltages
Timing Reference Voltages
Output Load
Current Source IOLmax/IOHmax; CL = 100 pF
http://onsemi.com
3
CAT93C46
Device Operation
The CAT93C46 is a 1024−bit nonvolatile memory
intended for use with industry standard microprocessors.
The CAT93C46 can be organized as either registers of 16
bits or 8 bits. When organized as X16, seven 9−bit
instructions control the reading, writing and erase
operations of the device. When organized as X8, seven
10−bit instructions control the reading, writing and erase
operations of the device. The CAT93C46 operates on a
single power supply and will generate on chip the high
voltage required during any write operation.
Instructions, addresses, and write data are clocked into the
DI pin on the rising edge of the clock (SK). The DO pin is
normally in a high impedance state except when reading data
from the device, or when checking the ready/busy status
during a write operation. The serial communication protocol
follows the timing shown in Figure 2.
The ready/busy status can be determined after the start of
internal write cycle by selecting the device (CS high) and
polling the DO pin; DO low indicates that the write
operation is not completed, while DO high indicates that the
device is ready for the next instruction. If necessary, the DO
pin may be placed back into a high impedance state during
chip select by shifting a dummy “1” into the DI pin. The DO
pin will enter the high impedance state on the rising edge of
the clock (SK). Placing the DO pin into the high impedance
state is recommended in applications where the DI pin and
the DO pin are to be tied together to form a common DI/O
pin. The Ready/Busy flag can be disabled only in Ready
state; no change is allowed in Busy state.
The format for all instructions sent to the device is a
logical “1” start bit, a 2−bit (or 4−bit) opcode, 6−bit address
(an additional bit when organized X8) and for write
operations a 16−bit data field (8−bit for X8 organization).
Read
Upon receiving a READ command (Figure 3) and an
address (clocked into the DI pin), the DO pin of the
CAT93C46 will come out of the high impedance state and,
after sending an initial dummy zero bit, will begin shifting
out the data addressed (MSB first). The output data bits will
toggle on the rising edge of the SK clock and are stable after
the specified time delay (tPD0 or tPD1).
Erase/Write Enable and Disable
The CAT93C46 powers up in the write disable state. Any
writing after power−up or after an EWDS (write disable)
instruction must first be preceded by the EWEN (write
enable) instruction. Once the write instruction is enabled, it
will remain enabled until power to the device is removed, or
the EWDS instruction is sent. The EWDS instruction can be
used to disable all CAT93C46 write and erase instructions,
and will prevent any accidental writing or clearing of the
device. Data can be read normally from the device
regardless of the write enable/disable status. The EWEN and
EWDS instructions timing is shown in Figure 4.
Table 8. INSTRUCTION SET
Address
Data
Instruction
Start Bit
Opcode
x8
x16
x8
x16
Comments
READ
1
10
A6−A0
A5−A0
Read Address AN–A0
ERASE
1
11
A6−A0
A5−A0
Clear Address AN–A0
WRITE
1
01
A6−A0
A5−A0
EWEN
1
00
11XXXXX
11XXXX
Write Enable
EWDS
1
00
00XXXXX
00XXXX
Write Disable
ERAL
1
00
10XXXXX
10XXXX
Clear All Addresses
WRAL
1
00
01XXXXX
01XXXX
D7−D0
D7−D0
http://onsemi.com
4
D15−D0
D15−D0
Write Address AN–A0
Write All Addresses
CAT93C46
tSKHI
tSKLOW
tCSH
SK
tDIS
tDIH
VALID
DI
VALID
tCSS
CS
tDIS
tPD0, tPD1
DO
tCSMIN
DATA VALID
Figure 2. Synchronous Data Timing
SK
tCSMIN
CS
AN
DI
1
1
AN−1
STANDBY
A0
0
tPD0
HIGH−Z
DO
tHZ
HIGH−Z
0
DN
DN−1
D1
D0
Figure 3. Read Instruction Timing
SK
STANDBY
CS
DI
1
0
0
*
* ENABLE = 11
DISABLE = 00
Figure 4. EWEN/EWDS Instruction Timing
http://onsemi.com
5
CAT93C46
Write
Erase All
After receiving a WRITE command (Figure 5), address
and the data, the CS (Chip Select) pin must be deselected for
a minimum of tCSMIN. The falling edge of CS will start the
self clocking for auto−clear and data store cycles on the
memory location specified in the instruction. The clocking
of the SK pin is not necessary after the device has entered the
self clocking mode. The ready/busy status of the CAT93C46
can be determined by selecting the device and polling the
DO pin. Since this device features Auto−Clear before write,
it is NOT necessary to erase a memory location before it is
written into.
Upon receiving an ERAL command (Figure 7), the CS
(Chip Select) pin must be deselected for a minimum of
tCSMIN. The falling edge of CS will start the self clocking
clear cycle of all memory locations in the device. The
clocking of the SK pin is not necessary after the device has
entered the self clocking mode. The ready/busy status of the
CAT93C46 can be determined by selecting the device and
polling the DO pin. Once cleared, the contents of all memory
bits return to a logical “1” state.
Write All
Upon receiving a WRAL command and data, the CS
(Chip Select) pin must be deselected for a minimum of
tCSMIN (Figure 8). The falling edge of CS will start the self
clocking data write to all memory locations in the device.
The clocking of the SK pin is not necessary after the device
has entered the self clocking mode. The ready/busy status of
the CAT93C46 can be determined by selecting the device
and polling the DO pin. It is not necessary for all memory
locations to be cleared before the WRAL command is
executed.
Erase
Upon receiving an ERASE command and address, the CS
(Chip Select) pin must be de−asserted for a minimum of
tCSMIN (Figure 6). The falling edge of CS will start the self
clocking clear cycle of the selected memory location. The
clocking of the SK pin is not necessary after the device has
entered the self clocking mode. The ready/busy status of the
CAT93C46 can be determined by selecting the device and
polling the DO pin. Once cleared, the content of a cleared
location returns to a logical “1” state.
SK
tCSMIN
CS
AN
DI
STANDBY
STATUS
VERIFY
1
0
AN−1
A0
DN
D0
1
tSV
DO
tHZ
HIGH−Z
READY
BUSY
tEW
Figure 5. Write Instruction Timing
http://onsemi.com
6
HIGH−Z
CAT93C46
SK
CS
STANDBY
STATUS VERIFY
AN
DI
1
AN−1
tCS MIN
A0
1
1
tSV
tHZ
HIGH−Z
DO
BUSY
READY
HIGH−Z
tEW
Figure 6. Erase Instruction Timing
SK
CS
STATUS VERIFY
STANDBY
tCS MIN
DI
1
0
1
0
0
tSV
tHZ
HIGH−Z
DO
BUSY
READY
HIGH−Z
tEW
Figure 7. ERAL Instruction Timing
SK
CS
STATUS VERIFY
STANDBY
tCSMIN
DI
1
0
0
0
1
DN
D0
tSV
tHZ
BUSY
DO
tEW
Figure 8. WRAL Instruction Timing
http://onsemi.com
7
READY
HIGH−Z
CAT93C46
PACKAGE DIMENSIONS
PDIP−8, 300 mils
CASE 646AA−01
ISSUE A
SYMBOL
MIN
NOM
A
E1
5.33
A1
0.38
A2
2.92
3.30
4.95
b
0.36
0.46
0.56
b2
1.14
1.52
1.78
c
0.20
0.25
0.36
D
9.02
9.27
10.16
E
7.62
7.87
8.25
E1
6.10
6.35
7.11
e
PIN # 1
IDENTIFICATION
MAX
2.54 BSC
eB
7.87
L
2.92
10.92
3.30
3.80
D
TOP VIEW
E
A2
A
A1
c
b2
L
e
eB
b
SIDE VIEW
END VIEW
Notes:
(1) All dimensions are in millimeters.
(2) Complies with JEDEC MS-001.
http://onsemi.com
8
CAT93C46
PACKAGE DIMENSIONS
SOIC 8, 150 mils
CASE 751BD−01
ISSUE O
E1
E
SYMBOL
MIN
A
1.35
1.75
A1
0.10
0.25
b
0.33
0.51
c
0.19
0.25
D
4.80
5.00
E
5.80
6.20
E1
3.80
MAX
4.00
1.27 BSC
e
PIN # 1
IDENTIFICATION
NOM
h
0.25
0.50
L
0.40
1.27
θ
0º
8º
TOP VIEW
D
h
A1
θ
A
c
e
b
L
SIDE VIEW
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MS-012.
http://onsemi.com
9
CAT93C46
PACKAGE DIMENSIONS
SOIC−8, 208 mils
CASE 751BE−01
ISSUE O
SYMBOL
MIN
NOM
2.03
A
E1 E
MAX
A1
0.05
0.25
b
0.36
0.48
c
0.19
0.25
D
5.13
5.33
E
7.75
8.26
E1
5.13
5.38
1.27 BSC
e
L
0.51
0.76
θ
0º
8º
PIN#1 IDENTIFICATION
TOP VIEW
D
A
e
b
q
L
A1
SIDE VIEW
c
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with EIAJ EDR-7320.
http://onsemi.com
10
CAT93C46
PACKAGE DIMENSIONS
TSSOP8, 4.4x3
CASE 948AL−01
ISSUE O
b
SYMBOL
MIN
NOM
A
E1
E
MAX
1.20
A1
0.05
A2
0.80
b
0.19
0.15
0.90
1.05
0.30
c
0.09
D
2.90
3.00
3.10
E
6.30
6.40
6.50
E1
4.30
4.40
4.50
e
0.20
0.65 BSC
L
1.00 REF
L1
0.50
θ
0º
0.60
0.75
8º
e
TOP VIEW
D
A2
c
q1
A
A1
L1
SIDE VIEW
L
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-153.
http://onsemi.com
11
CAT93C46
PACKAGE DIMENSIONS
TDFN8, 2x3
CASE 511AK−01
ISSUE A
D
A
e
b
E2
E
PIN#1
IDENTIFICATION
A1
PIN#1 INDEX AREA
D2
TOP VIEW
SYMBOL
MIN
SIDE VIEW
NOM
A
0.70
0.75
0.80
0.00
0.02
0.05
A2
0.45
0.55
0.65
A2
0.20 REF
A3
b
0.20
0.25
0.30
D
1.90
2.00
2.10
D2
1.30
1.40
1.50
E
2.90
3.00
3.10
E2
1.20
1.30
1.40
e
L
BOTTOM VIEW
MAX
A1
A3
FRONT VIEW
0.50 TYP
0.20
0.30
L
0.40
Notes:
(1) All dimensions are in millimeters.
(2) Complies with JEDEC MO-229.
http://onsemi.com
12
CAT93C46
Ordering Information
Specific
Device
marking
Pkg Type
Temperature Range
CAT93C46LI−G
93C46L
PDIP−8
CAT93C46VI−G
93C46V
CAT93C46VI−GT3
Lead
Finish
Shipping
I = Industrial
(−40°C to +85°C)
NiPdAu
Tube, 50 Units / Tube
SOIC−8, JEDEC
I = Industrial
(−40°C to +85°C)
NiPdAu
Tube, 100 Units / Tube
93C46V
SOIC−8, JEDEC
I = Industrial
(−40°C to +85°C)
NiPdAu
Tape & Reel, 3000 Units / Reel
EK
TDFN−8
I = Industrial
(−40°C to +85°C)
NiPdAu
Tape & Reel, 3000 Units / Reel
CAT93C46WI−G
93C46W
SOIC−8, JEDEC
I = Industrial
(−40°C to +85°C)
NiPdAu
Tube, 100 Units / Tube
CAT93C46WI−GT3
93C46W
SOIC−8, JEDEC
I = Industrial
(−40°C to +85°C)
NiPdAu
Tape & Reel, 3000 Units / Reel
CAT93C46XI
93C46X
SOIC−8, EIAJ
I = Industrial
(−40°C to +85°C)
Matte−Tin
Tube, 94 Units / Tube
CAT93C46XI−T2
93C46X
SOIC−8, EIAJ
I = Industrial
(−40°C to +85°C)
Matte−Tin
Tape & Reel, 2000 Units / Reel
CAT93C46YI−G
M46
TSSOP−8
I = Industrial
(−40°C to +85°C)
NiPdAu
Tube, 100 Units / Tube
CAT93C46YI−GT3
M46
TSSOP−8
I = Industrial
(−40°C to +85°C)
NiPdAu
Tape & Reel, 3000 Units / Reel
OPN
CAT93C46VP2I−GT3
(Note 10)
10. Not recommended for new designs.
11. All packages are RoHS−compliant (Lead−free, Halogen−free).
12. The standard lead finish is NiPdAu.
13. For additional package and temperature options, please contact your nearest ON Semiconductor Sales office.
14. For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
15. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device
Nomenclature document, TND310/D, available at www.onsemi.com
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
13
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
CAT93C46/D