NCP715 D

NCP715
50 mA Ultra-Low Iq, Wide
Input Voltage, Low Dropout
Linear Voltage Regulator
The NCP715 is 50 mA LDO Linear Voltage Regulator. It is a very
stable and accurate device with ultra−low ground current consumption
(4.7 mA over the full output load range) and a wide input voltage range
(up to 24 V). The regulator incorporates several protection features
such as Thermal Shutdown and Current Limiting.
www.onsemi.com
MARKING
DIAGRAMS
Features
• Operating Input Voltage Range: 2.5 V to 24 V
• Fixed Voltage Options Available: 1.2 V to 5.3 V
• Ultra Low Quiescent Current: Max. 4.7 mA Over Full Load and
•
•
•
•
•
•
Temperature
±2% Accuracy Over Full Load, Line and Temperature Variations
PSRR: 52 dB at 100 kHz
Noise: 190 mVRMS from 200 Hz to 100 kHz
Thermal Shutdown and Current Limit protection
Available in XDFN6 1.5 x 1.5 mm and SC−70 (SC−88A) Package
These are Pb−Free Devices
Typical Applications
• Portable Equipment
• Communication Systems
1.2 V < Vout < 5.3 V
2.5 V < Vout < 24 V
OUT
IN
1 mF
Ceramic
NCP715
NC
GND
NC
XDFN6
CASE 711AE
SC−70−5
(SC−88A)
CASE 419A
1
XX MG
G
XX MG
G
XX
= Specific Device Code
M
= Date Code
G
= Pb−Free Package
(Note: Microdot may be in either location)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 18 of this data sheet.
1 mF
Ceramic
Figure 1. Typical Application Schematic
© Semiconductor Components Industries, LLC, 2016
June, 2016 − Rev. 4
1
Publication Order Number:
NCP715/D
NCP715
IN
THERMAL
SHUTDOWN
UVLO
BANDGAP
REFERENCE
MOSFET
DRIVER WITH
CURRENT LIMIT
OUT
EEPROM
GND
Figure 2. Simplified Block Diagram
Figure 3. Pin Description
PIN FUNCTION DESCRIPTION
Pin No.
SC−70
XDFN6
Pin Name
5
6
OUT
Regulated output voltage pin. A small 0.47 mF ceramic capacitor is needed from this pin to
ground to assure stability.
1
2
N/C
No connection. This pin can be tied to ground to improve thermal dissipation or left disconnected.
2
3
GND
Power supply ground.
3
4
N/C
No connection. This pin can be tied to ground to improve thermal dissipation or left disconnected.
−
5
N/C
No connection. This pin can be tied to ground to improve thermal dissipation or left disconnected.
4
1
IN
Description
Input pin. A small capacitor is needed from this pin to ground to assure stability.
www.onsemi.com
2
NCP715
ABSOLUTE MAXIMUM RATINGS
Rating
Input Voltage (Note 1)
Output Voltage
Output Short Circuit Duration
Maximum Junction Temperature
Operating Ambient Temperature Range
Symbol
Value
Unit
VIN
−0.3 to 24
V
VOUT
−0.3 to 6
V
tSC
Indefinite
s
TJ(MAX)
150
°C
TA
−40 to 125
°C
TSTG
−55 to 150
°C
ESD Capability, Human Body Model (Note 2)
ESDHBM
2000
V
ESD Capability, Machine Model (Note 2)
ESDMM
200
V
Storage Temperature Range
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per EIA/JESD22−A114
ESD Machine Model tested per EIA/JESD22−A115
ESD Charged Device Model tested per EIA/JESD22−C101E
Latch up Current Maximum Rating tested per JEDEC standard: JESD78.
THERMAL CHARACTERISTICS
Rating
Symbol
Value
Unit
Thermal Characteristics, SC−70
Thermal Resistance, Junction−to−Air
RqJA
390
°C/W
Thermal Characteristics, XDFN6
Thermal Resistance, Junction−to−Air
RqJA
260
°C/W
www.onsemi.com
3
NCP715
ELECTRICAL CHARACTERISTICS − Voltage Version 1.2 V
−40°C ≤ TJ ≤ 125°C; VIN = 2.5 V; IOUT = 1 mA, CIN = COUT = 1.0 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 5)
Parameter
Operating Input Voltage
Test Conditions
Symbol
Min
IOUT ≤ 10 mA
VIN
10 mA< IOUT < 50 mA
Output Voltage Accuracy
Typ
Max
Unit
2.5
24
V
3.0
24
2.5 V < VIN < 24 V, 0 < IOUT ≤ 10 mA
VOUT
1.164
1.2
1.236
V
3.0 V < VIN < 24 V, 0 mA < IOUT < 50 mA
VOUT
1.164
1.2
1.236
V
3.0 V < VIN < 24 V, 1 mA < IOUT < 50 mA,
−20°C < TJ < 125°C;
VOUT
1.176
1.2
1.224
V
Line Regulation
2.5 V ≤ VIN ≤ 24 V, IOUT = 1 mA
RegLINE
2
mV
Load Regulation
IOUT = 0 mA to 50 mA
RegLOAD
5
mV
Dropout Voltage (Note 3)
Maximum Output Current
VDO
(Note 6)
IOUT
0 < IOUT < 50 mA, −40 < TA < 85°C
IGND
100
3.2
0 < IOUT < 50 mA, VIN = 24 V
Power Supply Rejection Ratio
Output Noise Voltage
Thermal Shutdown Temperature
(Note 4)
Thermal Shutdown Hysteresis (Note 4)
VIN = 3.0 V, VOUT = 1.2 V
VPP = 200 mV modulation
IOUT = 1 mA, COUT= 10 mF
f = 100 kHz
−
mV
200
mA
4.2
mA
5.8
PSRR
60
dB
VOUT = 1.2 V, IOUT = 50 mA
f = 200 Hz to 100 kHz, COUT = 10 mF
VN
65
mVrms
Temperature increasing from TJ = +25°C
TSD
170
°C
Temperature falling from TSD
TSDH
−
15
−
°C
3. Not Characterized at VIN = 3.0 V, VOUT = 1.2 V, IOUT = 50 mA.
4. Guaranteed by design and characterization.
5. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA =
25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
6. Respect SOA.
www.onsemi.com
4
NCP715
ELECTRICAL CHARACTERISTICS − Voltage Version 1.5 V
−40°C ≤ TJ ≤ 125°C; VIN = 2.5 V; IOUT = 1 mA, CIN = COUT = 1.0 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 9)
Parameter
Operating Input Voltage
Test Conditions
Symbol
Min
IOUT ≤ 10 mA
VIN
10 mA < IOUT < 50 mA
Output Voltage Accuracy
Typ
Max
Unit
2.5
24
V
3.0
24
2.5 V < VIN < 24 V, 0 < IOUT ≤ 10 mA
VOUT
1.455
1.5
1.545
V
3.0 V < VIN < 24 V, 0 < IOUT < 50 mA
VOUT
1.455
1.5
1.545
V
3.0 V < VIN < 24 V, 1 mA < IOUT < 50 mA,
−20°C < TJ < 125°C;
VOUT
1.470
1.5
1.530
V
Line Regulation
VOUT + 1 V ≤ VIN ≤ 24 V, IOUT = 1 mA
RegLINE
2
mV
Load Regulation
IOUT = 0 mA to 50 mA
RegLOAD
5
mV
Dropout Voltage (Note 7)
Maximum Output Current
Ground Current
VDO
(Note 10)
IOUT
0 < IOUT < 50 mA, −40 < TA < 85°C
IGND
100
3.2
0 < IOUT < 50 mA, VIN = 24 V
Power Supply Rejection Ratio
Output Noise Voltage
Thermal Shutdown Temperature
(Note 8)
Thermal Shutdown Hysteresis (Note 8)
VIN = 3.0 V, VOUT = 1.5 V
VPP = 200 mV modulation
IOUT = 1 mA, COUT = 10 mF
f = 100 kHz
−
mV
200
mA
4.2
mA
5.8
mA
PSRR
56
dB
VOUT = 1.5 V, IOUT = 50 mA
f = 200 Hz to 100 kHz, COUT = 10 mF
VN
75
mVrms
Temperature increasing from TJ = +25°C
TSD
170
°C
Temperature falling from TSD
TSDH
−
15
−
°C
7. Not Characterized at VIN = 3.0 V, VOUT = 1.5 V, IOUT = 50 mA.
8. Guaranteed by design and characterization.
9. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at
TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
10. Respect SOA.
www.onsemi.com
5
NCP715
ELECTRICAL CHARACTERISTICS − Voltage Version 1.8 V
−40°C ≤ TJ ≤ 125°C; VIN = 2.8V; IOUT = 1 mA, CIN = COUT = 1.0 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 13)
Parameter
Operating Input Voltage
Test Conditions
Symbol
Min
IOUT ≤10 mA
VIN
10 mA < IOUT < 50 mA
Output Voltage Accuracy
Typ
Max
Unit
2.8
24
V
3.0
24
2.8 V < VIN < 24 V, 0 < IOUT < 10 mA
VOUT
1.746
1.8
1.854
V
3.0 V < VIN < 24 V, 1 mA < IOUT < 50 mA,
−20°C < TJ < 125°C;
VOUT
1.764
1.8
1.836
V
Line Regulation
3 V ≤ VIN ≤ 24 V, IOUT = 1 mA
RegLINE
3
mV
Load Regulation
IOUT = 0 mA to 50 mA
RegLOAD
10
mV
Dropout Voltage (Note 11)
Maximum Output Current
Ground Current
VDO
(Note 14)
IOUT
0 < IOUT < 50 mA, −40 < TA < 85°C
IGND
mV
100
3.2
0 < IOUT < 50 mA, VIN = 24 V
Power Supply Rejection Ratio
Output Noise Voltage
Thermal Shutdown Temperature
(Note 12)
Thermal Shutdown Hysteresis
(Note 12)
VIN = 3.0 V, VOUT = 1.8 V
VPP = 200 mV modulation
IOUT = 1 mA, COUT =10 mF
f = 100 kHz
200
mA
4.2
mA
5.8
mA
PSRR
60
dB
VOUT = 1.8 V, IOUT = 50 mA
f = 200 Hz to 100 kHz, COUT = 10 mF
VN
95
mVrms
Temperature increasing from TJ = +25°C
TSD
170
°C
Temperature falling from TSD
TSDH
−
15
−
°C
11. Not characterized at VIN = 3.0 V, VOUT = 1.8 V, IOUT = 50 mA
12. Guaranteed by design and characterization.
13. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA =
25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
14. Respect SOA.
www.onsemi.com
6
NCP715
ELECTRICAL CHARACTERISTICS − Voltage Version 2.5 V
−40°C ≤ TJ ≤ 125°C; VIN = 3.5 V; IOUT = 1 mA, CIN = COUT = 1.0 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 17)
Parameter
Test Conditions
Symbol
Min
Operating Input Voltage
0 < IOUT < 50 mA
VIN
3.5
Output Voltage Accuracy
3.5 V < VIN < 24 V, 0 < IOUT < 50 mA
VOUT
2.45
Line Regulation
VOUT + 1 V ≤ VIN ≤ 24 V, IOUT = 1 mA
RegLINE
3
mV
Load Regulation
IOUT = 0 mA to 50 mA
RegLOAD
10
mV
Dropout Voltage (Note 15)
VDO = VIN – (VOUT(NOM) – 75 mV)
IOUT = 50 mA
VDO
260
Maximum Output Current
(Note 18)
IOUT
0 < IOUT < 50 mA, −40 < TA < 85°C
IGND
Ground Current
Power Supply Rejection Ratio
Output Noise Voltage
Thermal Shutdown Temperature
(Note 16)
Thermal Shutdown Hysteresis
(Note 16)
Typ
2.5
100
3.2
0 < IOUT < 50 mA, VIN = 24 V
VIN = 3.5 V, VOUT = 2.5 V
VPP = 200 mV modulation
IOUT = 1 mA, COUT =10 mF
f = 100 kHz
Max
Unit
24
V
2.55
V
450
mV
200
mA
4.2
mA
5.8
mA
PSRR
60
dB
VOUT = 2.5 V, IOUT = 50 mA
f = 200 Hz to 100 kHz, COUT = 10 mF
VN
115
mVrms
Temperature increasing from TJ = +25°C
TSD
170
°C
Temperature falling from TSD
TSDH
−
15
−
°C
15. Characterized when VOUT falls 75 mV below the regulated voltage and only for devices with VOUT = 2.5 V.
16. Guaranteed by design and characterization.
17. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at
TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
18. Respect SOA.
www.onsemi.com
7
NCP715
ELECTRICAL CHARACTERISTICS − Voltage Version 3.0 V
−40°C ≤ TJ ≤ 125°C; VIN = 4.0 V; IOUT = 1 mA, CIN = COUT = 1.0 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 21)
Parameter
Test Conditions
Symbol
Min
Operating Input Voltage
0 < IOUT < 50 mA
VIN
4.0
Output Voltage Accuracy
4.0 V < VIN < 24 V, 0< IOUT < 50 mA
VOUT
2.94
Typ
3.0
Max
Unit
24
V
3.06
V
Line Regulation
VOUT + 1 V ≤ VIN ≤ 24 V, IOUT = 1 mA
RegLINE
3
mV
Load Regulation
IOUT = 0 mA to 50 mA
RegLOAD
10
mV
VDO = VIN – (VOUT(NOM) – 90 mV)
IOUT = 50 mA
VDO
Dropout voltage (Note 19)
Maximum Output Current
Ground current
(Note 22)
IOUT
0 < IOUT < 50 mA, -40 < TA < 85°C
IGND
100
3.2
0 < IOUT < 50 mA, VIN = 24 V
Power Supply Rejection Ratio
Output Noise Voltage
Thermal Shutdown Temperature
(Note 20)
Thermal Shutdown Hysteresis
(Note 20)
VIN = 4.0 V, VOUT = 3.0 V
VPP = 100 mV modulation
IOUT = 1 mA, COUT = 10 mF
f = 100 kHz
400
mV
200
mA
4.2
mA
5.8
mA
250
PSRR
60
dB
VOUT = 3 V, IOUT = 50 mA,
f = 200 Hz to 100 kHz, COUT = 10 mF
VN
135
mVrms
Temperature increasing from TJ = +25°C
TSD
170
°C
Temperature falling from TSD
TSDH
-
25
-
°C
19. Characterized when VOUT falls 90 mV below the regulated voltage and only for devices with VOUT = 3.0 V
20. Guaranteed by design and characterization.
21. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested
at TJ = TA = 25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as
possible.
22. Respect SOA
www.onsemi.com
8
NCP715
ELECTRICAL CHARACTERISTICS − Voltage Version 3.3 V
−40°C ≤ TJ ≤ 125°C; VIN = 4.3 V; IOUT = 1 mA, CIN = COUT = 1.0 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 25)
Parameter
Test Conditions
Symbol
Min
Operating Input Voltage
0 < IOUT < 50 mA
VIN
4.3
Output Voltage Accuracy
4.3 V < VIN < 24 V, 0 < IOUT < 50 mA
VOUT
3.234
Line Regulation
VOUT + 1 V ≤ VIN ≤ 24 V, IOUT = 1 mA
Load Regulation
IOUT = 0 mA to 50 mA
VDO = VIN – (VOUT(NOM) – 99 mV)
IOUT = 50 mA
VDO
230
Dropout Voltage (Note 23)
Maximum Output Current
Ground Current
Max
Unit
24
V
3.3
3.366
V
RegLINE
3
10
mV
RegLOAD
10
(Note 26)
IOUT
0 < IOUT < 50 mA, −40 < TA < 85°C
IGND
Typ
100
3.2
0 < IOUT < 50 mA, VIN = 24 V
Power Supply Rejection Ratio
Output Noise Voltage
Thermal Shutdown Temperature
(Note 24)
Thermal Shutdown Hysteresis
(Note 24)
VIN = 4.3 V, VOUT = 3.3 V
VPP = 200 mV modulation
IOUT = 1 mA, COUT =10 mF
f = 100 kHz
mV
350
mV
200
mA
4.2
mA
5.8
mA
PSRR
60
dB
VOUT = 4.3 V, IOUT = 50 mA
f = 200 Hz to 100 kHz, COUT = 10 mF
VN
140
mVrms
Temperature increasing from TJ = +25°C
TSD
170
°C
Temperature falling from TSD
TSDH
−
15
−
°C
23. Characterized when VOUT falls 99 mV below the regulated voltage and only for devices with VOUT = 3.3 V.
24. Guaranteed by design and characterization.
25. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA =
25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
26. Respect SOA.
www.onsemi.com
9
NCP715
ELECTRICAL CHARACTERISTICS − Voltage Version 5.0 V
−40°C ≤ TJ ≤ 125°C; VIN = 6.0 V; IOUT = 1 mA, CIN = COUT = 1 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 29)
Parameter
Test Conditions
Symbol
Min
Operating Input Voltage
0 < IOUT < 50 mA
VIN
6.0
Output Voltage Accuracy
6.0V < VIN < 24V, 0< IOUT < 50 mA
VOUT
4.9
Line Regulation
VOUT + 1 V ≤ VIN ≤ 24 V, Iout = 1mA
Load Regulation
IOUT = 0 mA to 50 mA
VDO = VIN – (VOUT(NOM) – 150 mV)
IOUT = 50 mA
VDO
Dropout Voltage (Note 27)
Maximum Output Current
Ground Current
Max
Unit
24
V
5.0
5.1
V
RegLINE
3
10
mV
RegLOAD
10
30
mV
230
350
mV
200
mA
4.2
mA
5.8
mA
(Note 30)
IOUT
0 < IOUT < 50 mA, −40 < TA < 85°C
IGND
Typ
90
3.2
0 < IOUT < 50 mA, VIN = 24 V
Power Supply Rejection Ratio
Output Noise Voltage
Thermal Shutdown Temperature
(Note 28)
Thermal Shutdown Hysteresis
(Note 28)
VIN = 6.0 V, VOUT = 5.0 V
VPP = 200 mV modulation
IOUT = 1 mA, COUT =10 mF
f = 100 kHz
PSRR
56
dB
VOUT = 5.0 V, IOUT = 50 mA
f = 200 Hz to 100 kHz, COUT = 10 mF
VN
190
mVrms
Temperature increasing from TJ = +25°C
TSD
170
°C
Temperature falling from TSD
TSDH
−
15
−
°C
27. Characterized when VOUT falls 150 mV below the regulated voltage and only for devices with VOUT = 5.0 V.
28. Guaranteed by design and characterization.
29. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA =
25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
30. Respect SOA.
www.onsemi.com
10
NCP715
ELECTRICAL CHARACTERISTICS − Voltage Version 5.3 V
−40°C ≤ TJ ≤ 125°C; VIN = 6.3 V; IOUT = 1 mA, CIN = COUT = 1 mF, unless otherwise noted. Typical values are at TJ = +25°C. (Note 33)
Parameter
Test Conditions
Symbol
Min
Operating Input Voltage
0 < IOUT < 50 mA
VIN
6.3
Output Voltage Accuracy
6.3V < VIN < 24V, 0.1 mA< IOUT < 50 mA
VOUT
5.194
Typ
Max
Unit
24
V
5.3
5.406
V
60
mV
Line Regulation
VOUT + 1 V ≤ VIN ≤ 24 V, IOUT = 1mA
RegLINE
20
Load Regulation
IOUT = 0.1 mA to 50 mA
RegLOAD
20
VDO = VIN – (VOUT(NOM) – 159 mV)
IOUT = 50 mA
VDO
230
Dropout Voltage (Note 31)
Maximum Output Current
Ground Current
(Note 34)
IOUT
0 < IOUT < 50 mA, −40 < TA < 85°C
IGND
90
3.2
0 < IOUT < 50 mA, VIN = 24 V
Power Supply Rejection Ratio
Output Noise Voltage
Thermal Shutdown Temperature
(Note 32)
Thermal Shutdown Hysteresis
(Note 32)
VIN = 6.3 V, VOUT = 5.3 V
VPP = 200 mV modulation
IOUT = 1 mA, COUT =10 mF
f = 100 kHz
mV
350
mV
200
mA
4.2
mA
5.8
mA
PSRR
55
dB
VOUT = 5.3 V, IOUT = 50 mA
f = 200 Hz to 100 kHz, COUT = 10 mF
VN
195
mVrms
Temperature increasing from TJ = +25°C
TSD
170
°C
Temperature falling from TSD
TSDH
−
15
−
°C
31. Characterized when VOUT falls 159 mV below the regulated voltage and only for devices with VOUT = 5.3 V.
32. Guaranteed by design and characterization.
33. Performance guaranteed over the indicated operating temperature range by design and/or characterization production tested at TJ = TA =
25°C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
34. Respect SOA.
www.onsemi.com
11
NCP715
1.2
2.506
VIN = 3.0 V
1.198
1.197
1.196
VIN = (5.0 − 24.0) V
1.195
1.194
1.193
1.192
−40
NCP715x12xxx
CIN = COUT = 1 mF
IOUT = 1 mA
−20
0
20
VIN = 3.0 V
2.504
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
1.199
2.502
2.5
VIN = (5.0 − 24.0) V
2.498
2.496
2.494
NCP715x25xxx
CIN = COUT = 1 mF
IOUT = 1 mA
2.492
40
60
80
100
2.49
−40
120
−20
0
3.315
5.015
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
5.02
3.312
3.309
3.306
3.303
3.294
−40
NCP715x33xxx
CIN = COUT = 1 mF
IOUT = 1 mA
VIN = 4.3 V to 24 V
−20
0
20
40
60
80
TEMPERATURE (°C)
100
VIN = 6.0 V
4.995
NCP715x50xxx
CIN = COUT = 1 mF
IOUT = 1 mA
4.99
0
20
40
60
80
100
JUNCTION TEMPERATURE (°C)
1.192
1.188
VIN = 3.0 V
VIN = 5.0 V
VIN = 10 V
VIN = 15 V
VIN = 20 V
VIN = 24 V
1.176
1.172
0
10
20
30
OUTPUT CURRENT (mA)
NCP715x25xxx
CIN = COUT = 1 mF
TA = 25°C
2.500
2.496
2.492
2.488
VIN = 3.5 V
VIN = 5.0 V
VIN = 10 V
VIN = 15 V
VIN = 20 V
VIN = 24 V
2.484
2.480
2.476
2.472
40
120
Figure 7. Output Voltage vs. Temperature
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
−20
2.504
1.180
120
5
4.98
−40
120
NCP715x12xxx
CIN = COUT = 1 mF
TA = 25°C
1.184
100
5.005
4.985
1.204
1.196
80
VIN = (8.0 − 24.0) V
5.01
Figure 6. Output Voltage vs. Temperature
1.200
60
Figure 5. Output Voltage vs. Temperature
3.318
3.297
40
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 4. Output Voltage vs. Temperature
3.3
20
50
0
Figure 8. Output Voltage vs. Output Current
10
20
30
OUTPUT CURRENT (mA)
40
Figure 9. Output Voltage vs. Output Current
www.onsemi.com
12
50
NCP715
3.312
OUTPUT VOLTAGE (V)
3.308
3.304
3.300
3.296
3.292
VIN = 4.3 V
VIN = 10 V
VIN = 15 V
VIN = 20 V
VIN = 24 V
3.288
3.284
5.016
NCP715x50xxx
CIN = COUT = 1 mF
TA = 25°C
5.008
OUTPUT VOLTAGE (V)
NCP715x33xxx
CIN = COUT = 1 mF
TA = 25°C
5.000
4.992
4.984
4.976
VIN = 6.0 V
VIN = 10 V
VIN = 15 V
VIN = 20 V
VIN = 24 V
4.968
4.960
3.280
4.952
0
10
20
30
40
0
50
10
OUTPUT CURRENT (mA)
Figure 10. Output Voltage vs. Output Current
50
NCP715x33xxx
CIN = COUT = 1 mF
350
TA = 125°C
300
250
TA = 25°C
200
150
TA = −40°C
100
DROPOUT VOLTAGE (mV)
DROPOUT VOLTAGE (mV)
40
400
NCP715x25xxx
CIN = COUT = 1 mF
350
50
300
TA = 125°C
250
TA = 25°C
200
150
100
TA = −40°C
50
0
0
0
10
20
30
40
0
50
10
OUTPUT CURRENT (mA)
20
30
40
50
OUTPUT CURRENT (mA)
Figure 12. Dropout Voltage vs. Output Current
Figure 13. Dropout Voltage vs. Output Current
400
40
GND, QUIESCENT CURRENT (mA)
NCP715x50xxx
CIN = COUT = 1 mF
350
DROPOUT VOLTAGE (mV)
30
Figure 11. Output Voltage vs. Output Current
400
300
TA = 125°C
250
200
TA = 25°C
150
100
TA = −40°C
50
0
20
OUTPUT CURRENT (mA)
0
10
20
30
40
50
NCP715x12xxx
CIN = COUT = 1 mF
TA = 25°C
35
30
25
20
15
IOUT = 0
IOUT = 50 mA
10
5
0
0
5
10
15
20
OUTPUT CURRENT (mA)
INPUT VOLTAGE (V)
Figure 14. Dropout Voltage vs. Output Current
Figure 15. Ground Current vs. Input Voltage
www.onsemi.com
13
25
NCP715
40
IOUT = 0
IOUT = 50 mA
35
NCP715x25xxx
CIN = COUT = 1 mF
TA = 25°C
30
GND, QUIESCENT CURRENT (mA)
GND, QUIESCENT CURRENT (mA)
40
25
20
15
10
5
0
30
25
20
15
10
5
0
0
5
10
15
20
25
0
5
10
INPUT VOLTAGE (V)
20
25
Figure 17. Ground Current vs. Input Voltage
4.5
40
NCP715x50xxx
CIN = COUT = 1 mF
TA = 25°C
IOUT = 0
IOUT = 50 mA
35
30
QUIESCENT CURRENT (mA)
GND, QUIESCENT CURRENT (mA)
15
INPUT VOLTAGE (V)
Figure 16. Ground Current vs. Input Voltage
25
20
15
10
5
0
5
10
15
20
4.3
4.0
3.8
3.5
3.3
3.0
2.8
2.5
−40
0
25
VIN = 3 V
VIN = 10 V
VIN = 24 V
−20
0
INPUT VOLTAGE (V)
NCP715x12xxx
CIN = COUT = 1 mF
IOUT = 0
20
40
60
80
100
120
TEMPERATURE (°C)
Figure 18. Ground Current vs. Input Voltage
Figure 19. Quiescent Current vs. Temperature
6.0
6.0
NCP715x25xxx
CIN = COUT = 1 mF
IOUT = 0
5.5
5.0
QUIESCENT CURRENT (mA)
QUIESCENT CURRENT (mA)
NCP715x33xxx
CIN = COUT = 1 mF
TA = 25°C
IOUT = 0
IOUT = 50 mA
35
4.5
4.0
3.5
3.0
VIN = 3.5 V
VIN = 10 V
VIN = 24 V
2.5
2.0
−40
−20
0
20
40
60
80
100
NCP715x33xxx
CIN = COUT = 1 mF
IOUT = 0
5.5
5.0
4.5
4.0
3.5
3.0
VIN = 4.3 V
VIN = 10 V
VIN = 24 V
2.5
2.0
−40
120
−20
0
20
40
60
80
100
120
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 20. Quiescent Current vs. Temperature
Figure 21. Quiescent Current vs. Temperature
www.onsemi.com
14
NCP715
100
NCP715x50xxx
CIN = COUT = 1 mF
IOUT = 0
5.5
5.0
4.5
4.0
3.5
3.0
VIN = 6 V
VIN = 10 V
VIN = 24 V
2.5
2.0
−40
PSRR (dB)
80
0
40
IOUT = 10 mA
0
20
40
60
80
100
0.1
120
1
10
100
TEMPERATURE (°C)
FREQUENCY (kHz)
Figure 22. Quiescent Current vs. Temperature
Figure 23. PSRR vs. Frequency
100
NCP715x25xxx
COUT = 10 mF
VIN = 3.5 V + 200 mVPP Modulation
TA = 25°C
IOUT = 1 mA
IOUT = 50 mA
NCP715x33xxx
COUT = 10 mF
VIN = 4.3 V + 200 mVPP Modulation
TA = 25°C
80
40
20
1000
IOUT = 1 mA
60
40
20
IOUT = 10 mA
IOUT = 10 mA
IOUT = 50 mA
0
0
0.1
1
10
100
0.1
1000
10
100
FREQUENCY (kHz)
Figure 24. PSRR vs. Frequency
Figure 25. PSRR vs. Frequency
1.6
OUTPUT VOLTAGE NOISE (mV/√Hz)
NCP715x50xxx
COUT = 10 mF
VIN = 6.0 V + 200 mVPP Modulation
TA = 25°C
IOUT = 1 mA
60
40
20
IOUT = 50 mA
IOUT = 10 mA
0
0.1
1
FREQUENCY (kHz)
100
PSRR (dB)
IOUT = 1 mA
IOUT = 50 mA
60
80
60
20
PSRR (dB)
100
−20
NCP715x12xxx
COUT = 10 mF
VIN = 3.0 V + 200 mVPP Modulation
TA = 25°C
80
PSRR (dB)
QUIESCENT CURRENT (mA)
6.0
1
10
100
1000
1000
COUT = 10 mF, 65.1 mVrms @ 200 Hz − 100 kHz
1.4
COUT = 4.7 mF, 80.5 mVrms @ 200 Hz − 100 kHz
1.2
COUT = 1.0 mF, 172.1 mVrms @ 200 Hz − 100 kHz
1.0
COUT = 0.47 mF, 208 mVrms @ 200 Hz − 100 kHz
COUT = 2.2 mF, 111.5 mVrms @ 200 Hz − 100 kHz
0.8
0.6
0.4
0.2
NCP715x12xxx
IOUT = 50 mA
TA = 25°C
VIN = 3 V
0.0
0.01
0.1
1
10
100
1000
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 26. PSRR vs. Frequency
Figure 27. Output Spectral Noise Density vs.
Frequency
www.onsemi.com
15
NCP715
COUT = 4.7 mF, 128.4 mVrms @ 200 Hz − 100 kHz
3.5
COUT = 2.2 mF, 152.2 mVrms @ 200 Hz − 100 kHz
3.0
COUT = 1.0 mF, 172.1 mVrms @ 200 Hz − 100 kHz
COUT = 0.47 mF, 203.6 mVrms @ 200 Hz − 100 kHz
2.5
NCP715x25xxx
IOUT = 50 mA
TA = 25°C
VIN = 3.5 V
2.0
1.5
1.0
0.5
0.0
0.01
0.1
1
10
100
1000
COUT = 10 mF, 137.1 mVrms @ 200 Hz − 100 kHz
4.5
COUT = 4.7 mF, 145.7 mVrms @ 200 Hz − 100 kHz
4.0
COUT = 2.2 mF, 170.6 mVrms @ 200 Hz − 100 kHz
3.5
COUT = 1.0 mF, 220.8 mVrms @ 200 Hz − 100 kHz
COUT = 0.47 mF, 271.1 mVrms @ 200 Hz − 100 kHz
3.0
NCP715x33xxx
IOUT = 50 mA
TA = 25°C
VIN = 4.3 V
2.5
2.0
1.5
1.0
0.5
0.0
0.01
0.1
1
10
100
1000
FREQUENCY (kHz)
FREQUENCY (kHz)
Figure 28. Output Spectral Noise Density vs.
Frequency
Figure 29. Output Spectral Noise Density vs.
Frequency
7.0
OUTPUT VOLTAGE NOISE (mV/√Hz)
5.0
COUT = 10 mF, 114.7 mVrms @ 200 Hz − 100 kHz
OUTPUT VOLTAGE NOISE (mV/√Hz)
OUTPUT VOLTAGE NOISE (mV/√Hz)
4.0
COUT = 10 mF, 186.1 mVrms @ 200 Hz − 100 kHz
COUT = 4.7 mF, 189.41 mVrms @ 200 Hz − 100 kHz
6.0
COUT = 2.2 mF, 207.6 mVrms @ 200 Hz − 100 kHz
COUT = 1.0 mF, 244.5 mVrms @ 200 Hz − 100 kHz
5.0
COUT = 0.47 mF, 305.0 mVrms @ 200 Hz − 100 kHz
4.0
NCP715x50xxx
IOUT = 50 mA
TA = 25°C
VIN = 6.0 V
3.0
2.0
1.0
0.0
0.01
0.1
1
10
100
1000
FREQUENCY (kHz)
Figure 30. Output Spectral Noise Density vs.
Frequency
Figure 31. Line Transient Response
Figure 32. Line Transient Response
Figure 33. Line Transient Response
www.onsemi.com
16
NCP715
Figure 34. Load Transient Response
Figure 35. Load Transient Response
Figure 36. Load Transient Response
Figure 37. Input Voltage Turn−On Response
Figure 38. Input Voltage Turn−On Response
Figure 39. Input Voltage Turn−On Response
www.onsemi.com
17
NCP715
APPLICATIONS INFORMATION
ambient temperature affect the rate of junction temperature
rise for the part. The maximum power dissipation the
NCP715 can handle is given by:
The NCP715 is the member of new family of Wide Input
Voltage Range Low Dropout Regulators which delivers
Ultra Low Ground Current consumption, Good Noise and
Power Supply Rejection Ratio Performance.
P D(MAX) +
Input Decoupling (CIN)
It is recommended to connect at least 0.1 mF Ceramic X5R
or X7R capacitor between IN and GND pin of the device.
This capacitor will provide a low impedance path for any
unwanted AC signals or Noise superimposed onto constant
Input Voltage. The good input capacitor will limit the
influence of input trace inductances and source resistance
during sudden load current changes.
Higher capacitance and lower ESR Capacitors will
improve the overall line transient response.
ƪTJ(MAX) * TAƫ
(eq. 1)
R qJA
The power dissipated by the NCP715 for given
application conditions can be calculated from the following
equations:
P D [ V INǒI GNDǒI OUTǓǓ ) I OUTǒV IN * V OUTǓ (eq. 2)
or
V IN(MAX) [
Output Decoupling (COUT)
P D(MAX) ) ǒV OUT
I OUTǓ
I OUT ) I GND
(eq. 3)
For reliable operation, junction temperature should be
limited to +125°C maximum.
The NCP715 does not require a minimum Equivalent
Series Resistance (ESR) for the output capacitor. The device
is designed to be stable with standard ceramics capacitors
with values of 0.47 mF or greater up to 10 mF. The X5R and
X7R types have the lowest capacitance variations over
temperature thus they are recommended.
Hints
VIN and GND printed circuit board traces should be as
wide as possible. When the impedance of these traces is
high, there is a chance to pick up noise or cause the regulator
to malfunction. Place external components, especially the
output capacitor, as close as possible to the NCP715, and
make traces as short as possible.
Power Dissipation and Heat sinking
The maximum power dissipation supported by the device
is dependent upon board design and layout. Mounting pad
configuration on the PCB, the board material, and the
ORDERING INFORMATION
Device
Nominal Output Voltage
Marking
NCP715SQ12T2G
1.2 V
5A
NCP715SQ15T2G
1.5 V
5C
NCP715SQ18T2G
1.8 V
5D
NCP715SQ25T2G
2.5 V
5E
NCP715SQ30T2G
3.0 V
5F
NCP715SQ33T2G
3.3 V
5G
NCP715SQ50T2G
5.0 V
5H
NCP715MX12TBG
1.2 V
Q
NCP715MX15TBG
1.5 V
R
NCP715MX18TBG
1.8 V
T
NCP715MX25TBG
2.5 V
V
NCP715MX30TBG
3.0 V
Y
NCP715MX33TBG
3.3 V
2
NCP715MX50TBG
5.0 V
5
NCP715MX53TBG
5.3 V
5
Marking Rotation
Package
−
SC88A/SC70
(Pb−Free)
Shipping†
3000 / Tape
& Reel
0°
XDFN6 1.5 x 1.5
(Pb−Free)
+180°
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
18
NCP715
PACKAGE DIMENSIONS
XDFN6 1.5x1.5, 0.5P
CASE 711AE
ISSUE B
D
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.10 AND 0.20mm FROM TERMINAL TIP.
L
A
B
L1
PIN ONE
REFERENCE
0.10 C
2X
2X
0.10 C
ÍÍÍ
ÍÍÍ
ÍÍÍ
DETAIL A
ALTERNATE TERMINAL
CONSTRUCTIONS
E
DIM
A
A1
A3
b
D
E
e
L
L1
L2
ÉÉÉ
ÉÉÉ
EXPOSED Cu
TOP VIEW
MOLD CMPD
DETAIL B
ALTERNATE
CONSTRUCTIONS
A
DETAIL B
0.05 C
A3
A1
MILLIMETERS
MIN
MAX
0.35
0.45
0.00
0.05
0.13 REF
0.20
0.30
1.50 BSC
1.50 BSC
0.50 BSC
0.40
0.60
--0.15
0.50
0.70
RECOMMENDED
MOUNTING FOOTPRINT*
0.05 C
5X
C
SIDE VIEW
DETAIL A
e
1
SEATING
PLANE
6X
5X
0.73
1.80
L
3
0.35
L2
0.83
0.50
PITCH
DIMENSIONS: MILLIMETERS
6
4
6X
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
b
0.10 C A
BOTTOM VIEW
0.05 C
B
NOTE 3
www.onsemi.com
19
NCP715
PACKAGE DIMENSIONS
SC−88A (SC−70−5/SOT−353)
CASE 419A−02
ISSUE L
A
G
5
4
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 419A−01 OBSOLETE. NEW STANDARD
419A−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
−B−
S
1
2
DIM
A
B
C
D
G
H
J
K
N
S
3
D 5 PL
0.2 (0.008)
M
B
M
N
INCHES
MIN
MAX
0.071
0.087
0.045
0.053
0.031
0.043
0.004
0.012
0.026 BSC
--0.004
0.004
0.010
0.004
0.012
0.008 REF
0.079
0.087
MILLIMETERS
MIN
MAX
1.80
2.20
1.15
1.35
0.80
1.10
0.10
0.30
0.65 BSC
--0.10
0.10
0.25
0.10
0.30
0.20 REF
2.00
2.20
J
C
K
H
SOLDER FOOTPRINT*
0.50
0.0197
0.65
0.025
0.65
0.025
0.40
0.0157
1.9
0.0748
SCALE 20:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
20
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCP715/D