MC74HC4060A D

MC74HC4060A
14-Stage Binary Ripple
Counter With Oscillator
High−Performance Silicon−Gate CMOS
The MC74HC4060A is identical in pinout to the standard CMOS
MC14060B. The device inputs are compatible with standard CMOS
outputs; with pullup resistors, they are compatible with LSTTL
outputs.
This device consists of 14 master−slave flip−flops and an oscillator
with a frequency that is controlled either by a crystal or by an RC
circuit connected externally. The output of each flip−flop feeds the
next and the frequency at each output is half of that of the preceding
one. The state of the counter advances on the negative−going edge of
the Osc In. The active−high Reset is asynchronous and disables the
oscillator to allow very low power consumption during stand−by
operation.
State changes of the Q outputs do not occur simultaneously because
of internal ripple delays. Therefore, decoded output signals are subject
to decoding spikes and may have to be gated with Osc Out 2 of the
HC4060A.
Features
•
•
•
•
•
•
•
•
•
Output Drive Capability: 10 LSTTL Loads
Outputs Directly Interface to CMOS, NMOS, and TTL
Operating Voltage Range: 2.0 to 6.0 V
Low Input Current: 1 mA
High Noise Immunity Characteristic of CMOS Devices
In Compliance With JEDEC Standard No. 7A Requirements
Chip Complexity: 390 FETs or 97.5 Equivalent Gates
NLV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant
www.onsemi.com
SOIC−16
D SUFFIX
CASE 751B
PIN ASSIGNMENT
VCC
Q10
Q8
Q9
16
15
14
13
Reset
11
12
© Semiconductor Components Industries, LLC, 2016
June, 2016 − Rev. 10
12
11
10
9
1
2
3
4
5
6
7
8
Q13
Q14
Q6
Q5
Q7
Q4
GND
16−Lead Package (Top View)
MARKING DIAGRAMS
16
16
HC40
60A
ALYWG
G
HC4060AG
AWLYWW
1
1
SOIC−16
A
L, WL
Y, YY
W, WW
G or G
Osc Out 1 Osc Out 2
Osc In
Osc Osc
Reset Osc In Out 1 Out 2
Q12
LOGIC DIAGRAM
10
TSSOP−16
DT SUFFIX
CASE 948F
TSSOP−16
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
(Note: Microdot may be in either location)
9
7
5
4
6
14
13
15
1
2
3
FUNCTION TABLE
Q4
Q5
Q6
Q7
Q8
Q9
Q10
Q12
Q13
Q14
Clock
Reset
Output State
X
L
L
H
No Change
Advance to Next State
All Outputs Are Low
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 4 of this data sheet.
Pin 16 = VCC
Pin 8 = GND
1
Publication Order Number:
MC74HC4060A/D
MC74HC4060A
MAXIMUM RATINGS
Symbol
Parameter
Value
Unit
–0.5 to +7.0
V
DC Input Voltage (Referenced to GND)
–0.5 to VCC + 0.5
V
DC Output Voltage (Referenced to GND)
VCC
DC Supply Voltage (Referenced to GND)
Vin
Vout
–0.5 to VCC + 0.5
V
Iin
DC Input Current, per Pin
±20
mA
Iout
DC Output Current, per Pin
±25
mA
ICC
DC Supply Current, VCC and GND Pins
±50
mA
PD
Power Dissipation in Still Air,
500
450
mW
Tstg
Storage Temperature Range
– 65 to + 150
_C
TL
Lead Temperature, 1 mm from Case for 10 Seconds
SOIC or TSSOP Package
SOIC Package†
TSSOP Package†
This device contains protection
circuitry to guard against damage
due to high static voltages or electric
fields. However, precautions must
be taken to avoid applications of any
voltage higher than maximum rated
voltages to this high−impedance circuit. For proper operation, Vin and
Vout should be constrained to the
range GND v (Vin or Vout) v VCC.
Unused inputs must always be
tied to an appropriate logic voltage
level (e.g., either GND or VCC).
Unused outputs must be left open.
_C
260
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of
these limits are exceeded, device functionality should not be assumed, damage may occur and
reliability may be affected.
†Derating: SOIC Package: –7 mW/_C from 65_ to 125_C
TSSOP Package: −6.1 mW/_C from 65_ to 125_C
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
Vin, Vout
Parameter
DC Supply Voltage (Referenced to GND)
Min
Max
Unit
2.5*
6.0
V
DC Input Voltage, Output Voltage (Referenced to GND)
TA
Operating Temperature Range, All Package Types
tr, tf
Input Rise/Fall Time
(Figure 1)
0
VCC
V
–55
+125
_C
0
0
0
1000
500
400
ns
VCC = 2.0 V
VCC = 4.5 V
VCC = 6.0 V
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond
the Recommended Operating Ranges limits may affect device reliability.
*The oscillator is guaranteed to function at 2.5 V minimum. However, parametrics are tested at
2.0 V by driving Pin 11 with an external clock source.
DC CHARACTERISTICS (Voltages Referenced to GND)
VCC
V
Guaranteed Limit
−55 to 25°C
≤85°C
≤125°C
Unit
VIH
Minimum High−Level Input Voltage
Vout = 0.1V or VCC −0.1V
|Iout| ≤ 20mA
2.0
3.0
4.5
6.0
1.50
2.10
3.15
4.20
1.50
2.10
3.15
4.20
1.50
2.10
3.15
4.20
V
VIL
Maximum Low−Level Input Voltage
Vout = 0.1V or VCC − 0.1V
|Iout| ≤ 20mA
2.0
3.0
4.5
6.0
0.50
0.90
1.35
1.80
0.50
0.90
1.35
1.80
0.50
0.90
1.35
1.80
V
VOH
Minimum High−Level Output Voltage
(Q4−Q10, Q12−Q14)
Vin = VIH or VIL
|Iout| ≤ 20mA
2.0
4.5
6.0
1.9
4.4
5.9
1.9
4.4
5.9
1.9
4.4
5.9
V
3.0
4.5
6.0
2.48
3.98
5.48
2.34
3.84
5.34
2.20
3.70
5.20
2.0
4.5
6.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
3.0
4.5
6.0
0.26
0.26
0.26
0.33
0.33
0.33
0.40
0.40
0.40
Symbol
Parameter
Condition
|Iout| ≤ 2.4mA
|Iout| ≤ 4.0mA
|Iout| ≤ 5.2mA
Vin =VIH or VIL
VOL
Maximum Low−Level Output Voltage
(Q4−Q10, Q12−Q14)
Vin = VIH or VIL
|Iout| ≤ 20mA
|Iout| ≤ 2.4mA
|Iout| ≤ 4.0mA
|Iout| ≤ 5.2mA
Vin = VIH or VIL
www.onsemi.com
2
V
MC74HC4060A
DC CHARACTERISTICS (Voltages Referenced to GND) (continued)
Symbol
Parameter
Condition
VOH
Minimum High−Level Output Voltage
(Osc Out 1, Osc Out 2)
Vin = VCC or GND
|Iout| ≤ 20mA
|Iout| ≤ 0.7mA
|Iout| ≤ 1.0mA
|Iout| ≤ 1.3mA
Vin =VCC or GND
VOL
Maximum Low−Level Output Voltage
(Osc Out 1, Osc Out 2)
Vin = VCC or GND
|Iout| ≤ 20mA
|Iout| ≤ 0.7mA
|Iout| ≤ 1.0mA
|Iout| ≤ 1.3mA
Vin =VCC or GND
Guaranteed Limit
VCC
V
−55 to 25°C
≤85°C
≤125°C
Unit
2.0
4.5
6.0
1.9
4.4
5.9
1.9
4.4
5.9
1.9
4.4
5.9
V
3.0
4.5
6.0
2.48
3.98
5.48
2.34
3.84
5.34
2.20
3.70
5.20
2.0
4.5
6.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
3.0
4.5
6.0
0.26
0.26
0.26
0.33
0.33
0.33
0.40
0.40
0.40
V
Iin
Maximum Input Leakage Current
Vin = VCC or GND
6.0
±0.1
±1.0
±1.0
mA
ICC
Maximum Quiescent Supply
Current (per Package)
Vin = VCC or GND
Iout = 0mA
6.0
4
40
160
mA
AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)
VCC
V
Guaranteed Limit
−55 to 25°C
≤85°C
≤125°C
Unit
fmax
Maximum Clock Frequency (50% Duty Cycle)
(Figures 1 and 4)
2.0
3.0
4.5
6.0
6.0
10
30
50
9.0
14
28
45
8.0
12
25
40
MHz
tPLH,
tPHL
Maximum Propagation Delay, Osc In to Q4*
(Figures 1 and 4)
2.0
3.0
4.5
6.0
300
180
60
51
375
200
75
64
450
250
90
75
ns
tPLH,
tPHL
Maximum Propagation Delay, Osc In to Q14*
(Figures 1 and 4)
2.0
3.0
4.5
6.0
500
350
250
200
750
450
275
220
1000
600
300
250
ns
tPHL
Maximum Propagation Delay, Reset to Any Q
(Figures 2 and 4)
2.0
3.0
4.5
6.0
195
75
39
33
245
100
49
42
300
125
61
53
ns
tPLH,
tPHL
Maximum Propagation Delay, Qn to Qn+1
(Figures 3 and 4)
2.0
3.0
4.5
6.0
75
60
15
13
95
75
19
16
125
95
24
20
ns
VCC
V
−55 to 25°C
≤85°C
≤125°C
Unit
2.0
3.0
4.5
6.0
75
27
15
13
95
32
19
16
110
36
22
19
ns
10
10
10
pF
Symbol
Parameter
AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns) − continued
Parameter
Symbol
tTLH,
tTHL
Cin
Maximum Output Transition Time, Any Output
(Figures 1 and 4)
Guaranteed Limit
Maximum Input Capacitance
* For TA = 25°C and CL = 50 pF, typical propagation delay from Clock to other Q outputs may be calculated with the following equations:
VCC = 2.0 V: tP = [93.7 + 59.3 (n−1)] ns
VCC = 4.5 V: tP = [30.25 + 14.6 (n−1)] ns
VCC = 3.0 V: tP = [61.5+ 34.4 (n−1)] ns
VCC = 6.0 V: tP = [24.4 + 12 (n−1)] ns
Typical @ 25°C, VCC = 5.0 V
CPD
35
Power Dissipation Capacitance (Per Package)*
* Used to determine the no−load dynamic power consumption: P D = CPD VCC
www.onsemi.com
3
2f
+ ICC VCC .
pF
MC74HC4060A
TIMING REQUIREMENTS (Input tr = tf = 6 ns)
Symbol
Parameter
Guaranteed Limit
VCC
V
−55 to 25°C
≤85°C
≤125°C
Unit
trec
Minimum Recovery Time, Reset Inactive to Clock
(Figure 2)
2.0
3.0
4.5
6.0
100
75
20
17
125
100
25
21
150
120
30
25
ns
tw
Minimum Pulse Width, Clock
(Figure 1)
2.0
3.0
4.5
6.0
75
27
15
13
95
32
19
16
110
36
23
19
ns
tw
Minimum Pulse Width, Reset
(Figure 2)
2.0
3.0
4.5
6.0
75
27
15
13
95
32
19
16
110
36
23
19
ns
Maximum Input Rise and Fall Times
(Figure 1)
2.0
3.0
4.5
6.0
1000
800
500
400
1000
800
500
400
1000
800
500
400
ns
tr, tf
ORDERING INFORMATION
Package
Shipping†
MC74HC4060ADG
SOIC−16
(Pb−Free)
48 Units / Rail
MC74HC4060ADR2G
SOIC−16
(Pb−Free)
2500 Units / Reel
NLV74HC4060ADR2G*
SOIC−16
(Pb−Free)
2500 Units / Reel
MC74HC4060ADTG
TSSOP−16
(Pb−Free)
96 Units / Rail
MC74HC4060ADTR2G
TSSOP−16
(Pb−Free)
2500 Units / Reel
NLVHC4060ADTR2G*
TSSOP−16
(Pb−Free)
2500 Units / Reel
Device
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
www.onsemi.com
4
MC74HC4060A
PIN DESCRIPTIONS
INPUTS
Osc In (Pin 11)
Osc Out 1, Osc Out 2 (Pins 9, 10)
Oscillator outputs. These pins are used in conjunction
with Osc In and the external components to form an
oscillator. When Osc In is being driven with an external
clock source, Osc Out 1 and Osc Out 2 must be left open
circuited. With the crystal oscillator configuration in
Figure 6, Osc Out 2 must be left open circuited.
Negative−edge triggering clock input. A high−to−low
transition on this input advances the state of the counter. Osc
In may be driven by an external clock source.
Reset (Pin 12)
Active−high reset. A high level applied to this input
asynchronously resets the counter to its zero state (forcing
all Q outputs low) and disables the oscillator.
OUTPUTS
Q4—Q10, Q12−Q14 (Pins 7, 5, 4, 6, 13, 15, 1, 2, 3)
Active−high outputs. Each Qn output divides the Clock
input frequency by 2N. The user should note the Q1, Q2, Q3
and Q11 are not available as outputs.
SWITCHING WAVEFORMS
tf
tw
tr
90%
50%
10%
Osc In
Reset
VCC
GND
tPHL
GND
tw
1/fMAX
Q
tPHL
tPLH
Q
VCC
50%
90%
50%
10%
50%
trec
tTLH
Osc In
tTHL
GND
Figure 1.
Figure 2.
TEST
POINT
VCC
Qn
OUTPUT
50%
DEVICE
UNDER
TEST
GND
tPLH
Qn+1
VCC
50%
tPHL
CL*
50%
*Includes all probe and jig capacitance
Figure 3.
Figure 4. Test Circuit
www.onsemi.com
5
MC74HC4060A
Q4
Q5
7
Osc Out 1
Osc In
Reset
Q13
Q14
1
2
3
C
Q
C
Q
C
Q
C
Q
C
Q
C
C
Q
C
Q
C
Q
C
Q
C
Q
C
R
Osc Out 2
5
Q12
Q
R
9
Q6 = Pin 4
Q7 = Pin 6
Q8 = Pin 14
Q9 = Pin 13
10
Q10 = Pin 15
VCC = Pin 16
GND = Pin 8
11
12
Figure 5. Expanded Logic Diagram
Reset
For 2.0V ≤ VCC ≤ 6.0V
10Rtc > RS > 2Rtc
400Hz ≤ f ≤ 400Khz:
12
Osc In
11
Osc Out 1
10
Osc Out 2
9
f[
Rtc
RS
Ctc
1
(finHz, Rtcinohms, Ctcinfarads)
2.2RtcCtc
The formula may vary for other frequencies.
Figure 6. Oscillator Circuit Using RC Configuration
Reset
12
Osc In
11
Osc Out 1
10
Rf
R1
C1
C2
Figure 7. Pierce Crystal Oscillator Circuit
www.onsemi.com
6
9
Osc Out 2
MC74HC4060A
TABLE 1. CRYSTAL OSCILLATOR AMPLIFIER SPECIFICATIONS (TA = 25°C; Input = Pin 11, Output = Pin 10)
Positive Reactance (Pierce)
Type
Input Resistance, Rin
60MW Minimum
Output Impedance, Zout (4.5V Supply)
200W (See Text)
Input Capacitance, Cin
5pF Typical
Output Capacitance, Cout
7pF Typical
Series Capacitance, Ca
5pF Typical
Open Loop Voltage Gain with Output at Full Swing, α
3Vdc Supply
4Vdc Supply
5Vdc Supply
6Vdc Supply
5.0 Expected Minimum
4.0 Expected Minimum
3.3 Expected Minimum
3.1 Expected Minimum
PIERCE CRYSTAL OSCILLATOR DESIGN
RS
1
2
LS
CS
1
2
1
Re
Xe
2
CO
Value are supplied by crystal manufacturer (parallel resonant crystal).
Figure 8. Equivalent Crystal Networks
RS
-jXC2
R
Rload
Ca
-jXCo
jXLs
Xload
Zload
-jXCs
Cin
-jXC
Cout
NOTE: C = C1 + Cin and R = R1 + Rout. Co is considered as part of
the load. Ca and Rf typically have minimal effect below 2MHz.
Values are listed in Table 1.
Figure 9. Series Equivalent Crystal Load
Figure 10. Parasitic Capacitances of the Amplifier
www.onsemi.com
7
MC74HC4060A
DESIGN PROCEDURES
The following procedure applies for oscillators operating below 2MHz where Z is a resistor R1. Above 2MHz, additional
impedance elements should be considered: Cout and Ca of the amp, feedback resistor Rf, and amplifier phase shift error from
180°C.
Step 1: Calculate the equivalent series circuit of the crystal at the frequency of oscillation.
Ze +
* jXCo(Rs ) jXLs * jXCs)
* jXCo ) Rs ) jXLs * jXCs
+ Re ) jXe
Reactance jXe should be positive, indicating that the crystal is operating as an inductive reactance at the oscillation frequency.
The maximum Rs for the crystal should be used in the equation.
Step 2: Determine β, the attenuation, of the feedback network. For a closed-loop gain of 2,Aνβ = 2,β = 2/Aν where Aν is
the gain of the HC4060A amplifier.
Step 3: Determine the manufacturer’s loading capacitance. For example: A manufacturer may specify an external load
capacitance of 32pF at the required frequency.
Step 4: Determine the required Q of the system, and calculate Rload, For example, a manufacturer specifies a crystal Q of
100,000. In-circuit Q is arbitrarily set at 20% below crystal Q or 80,000. Then Rload = (2πfoLS/Q) − Rs where Ls and Rs are
crystal parameters.
Step 5: Simultaneously solve, using a computer,
b+
XC @ XC2
(with feedback phase shift = 180°)
R @ Re ) XC2 (Xe * XC)
Xe + XC2 ) XC )
Rload +
ReXC2
R
+ XCload (where the loading capacitor is an external load, not including Co)
RXCoXC2 [(XC ) XC2)(XC ) XCo) * XC(XC ) XCo ) XC2)]
X2C2(XC ) XCo)2 ) R2(XC ) XCo ) XC2)2
( Eq 1
( Eq 2
( Eq 3
Here R = Rout + R1. Rout is amp output resistance, R1 is Z. The C corresponding to XC is given by C = C1 + Cin.
Alternately, pick a value for R1 (i.e, let R1 = RS). Solve Equations 1 and 2 for C1 and C2. Use Equation 3 and the fact that
Q = 2πfoLs/(Rs + Rload) to find in-circuit Q. If Q is not satisfactory pick another value for R1 and repeat the procedure.
CHOOSING R1
the first overtone. Rf must be large enough so as to not affect
Power is dissipated in the effective series resistance of the
the phase of the feedback network in an appreciable manner.
crystal. The drive level specified by the crystal manufacturer
ACKNOWLEDGEMENTS AND RECOMMENDED
is the maximum stress that a crystal can withstand without
REFERENCES
damage or excessive shift in frequency. R1 limits the drive
The
following
publications
were used in preparing this
level.
data
sheet
and
are
hereby
acknowledged
and recommended
To verify that the maximum dc supply voltage does not
for
reading:
overdrive the crystal, monitor the output frequency as a
Technical Note TN-24, Statek Corp.
function of voltage at Osc Out 2 (Pin 9). The frequency
Technical Note TN-7, Statek Corp.
should increase very slightly as the dc supply voltage is
D. Babin, “Designing Crystal Oscillators”, Machine
increased. An overdriven crystal will decrease in frequency
Design,
March 7, 1985.
or become unstable with an increase in supply voltage. The
D.
Babin,
“Guidelines for Crystal Oscillator Design”,
operating supply voltage must be reduced or R1 must be
Machine
Design,
April 25, 1985.
increased in value if the overdriven condition exists. The
user should note that the oscillator start-up time is
ALSO RECOMMENDED FOR READING:
proportional to the value of R1.
E. Hafner, “The Piezoelectric Crystal Unit-Definitions
and Method of Measurement”, Proc. IEEE, Vol. 57, No. 2,
Feb., 1969.
D. Kemper, L. Rosine, “Quartz Crystals for Frequency
Control”, Electro-Technology, June, 1969.
P. J. Ottowitz, “A Guide to Crystal Selection”, Electronic
Design, May, 1966.
SELECTING Rf
The feedback resistor, Rf, typically ranges up to 20MW. Rf
determines the gain and bandwidth of the amplifier. Proper
bandwidth insures oscillation at the correct frequency plus
roll-off to minimize gain at undesirable frequencies, such as
www.onsemi.com
8
MC74HC4060A
1
2
4
8
16
32
64
128
256
Clock
Reset
Q4
Q5
Q6
Q7
Q8
Q9
Q10
Q12
Q13
Q14
Figure 11. Timing Diagram
www.onsemi.com
9
512
1024
2048
4096
8192
16384
MC74HC4060A
PACKAGE DIMENSIONS
TSSOP−16
CASE 948F
ISSUE B
16X K REF
0.10 (0.004)
0.15 (0.006) T U
M
T U
S
V
S
S
K
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
K1
2X
L/2
16
9
J1
B
−U−
L
SECTION N−N
J
PIN 1
IDENT.
N
0.25 (0.010)
8
1
M
0.15 (0.006) T U
S
A
−V−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH. PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
N
F
DETAIL E
−W−
C
0.10 (0.004)
−T− SEATING
PLANE
H
D
DETAIL E
G
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
SOLDERING FOOTPRINT*
7.06
1
0.65
PITCH
16X
0.36
16X
1.26
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
10
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
−−−
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.18
0.28
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN
MAX
0.193 0.200
0.169 0.177
−−− 0.047
0.002 0.006
0.020 0.030
0.026 BSC
0.007
0.011
0.004 0.008
0.004 0.006
0.007 0.012
0.007 0.010
0.252 BSC
0_
8_
MC74HC4060A
PACKAGE DIMENSIONS
SOIC−16
CASE 751B−05
ISSUE K
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
−A−
16
9
−B−
1
P
8 PL
0.25 (0.010)
8
B
M
S
DIM
A
B
C
D
F
G
J
K
M
P
R
G
R
K
F
X 45 _
C
−T−
SEATING
PLANE
J
M
D
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0_
7_
0.229
0.244
0.010
0.019
16 PL
0.25 (0.010)
M
T B
S
A
S
SOLDERING FOOTPRINT*
8X
6.40
16X
1
1.12
16
16X
0.58
1.27
PITCH
8
9
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
11
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC74HC4060A/D