ACS253MS Radiation Hardened Dual 4-Input Multiplexer with Three-State Outputs November 1997 Features Description • QML Qualified Per MIL-PRF-38535 Requirements The Radiation Hardened ACS253MS is a Dual 4-Channel Multiplexer having two common binary control inputs for selecting 1 of 4 data channels. All inputs and outputs are buffered and are designed for balanced propagation delay and transition times. • 1.25Micron Radiation Hardened SOS CMOS • Radiation Environment - Latch-up Free Under any Conditions - Total Dose . . . . . . . . . . . . . . . . . . . . . . 3 x 105 RAD(Si) - SEU Immunity . . . . . . . . . . . <1 x 10-10 Errors/Bit/Day - SEU LET Threshold . . . . . . . . . . . >100MeV/(mg/cm2) Separate Output Enable inputs are provided to ease system design. When OE1 or OE2 are set HIGH, the corresponding output is configured into a high impedance state. The ACS253MS is fabricated on a CMOS Silicon on Sapphire (SOS) process, which provides an immunity to Single Event Latch-up and the capability of highly reliable performance in any radiation environment. These devices offer significant power reduction and faster performance when compared to ALSTTL types. • Input Logic Levels . . .VIL = (0.3)(VCC), VIH = (0.7)(VCC) • Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±8mA • Quiescent Supply Current. . . . . . . . . . . . . . . . . . . 400µs • Propagation Delay - Enable to Output . . . . . . . . . . . . . . . . . . . . . . . . . 12ns - Input or Address to Output . . . . . . . . . . . . . . . . . 15ns Specifications for Rad Hard QML devices are controlled by the Defense Supply Center in Columbus (DSCC). The SMD numbers listed below must be used when ordering. Detailed Electrical Specifications for the ACS253 are contained in SMD 5962-98007. A “hot-link” is provided on our homepage with instructions for downloading. http://www.intersil.com/data/sm/index.htm Applications • Digital Channel Selection • Data Routing • High Frequency Switching Ordering Information SMD PART NUMBER TEMP. RANGE (oC) INTERSIL PART NUMBER 5962F9800701VEC ACS253DMSR-02 N/A ACS253D/Sample-02 5962F9800701VXC ACS253KMSR-02 N/A N/A -55 to 125 25 PACKAGE 16 Ld SBDIP CASE OUTLINE CDIP2-T16 16 Ld SBDIP CDIP2-T16 -55 to 125 16 Ld Flatpack CDFP4-F16 ACS253K/Sample-02 25 16 Ld Flatpack CDFP4-F16 ACS253HMSR-02 25 Die N/A Pinouts ACS253 (SBDIP) TOP VIEW ACS253 (FLATPACK) TOP VIEW 1OE 1 16 VCC 1OE 1 16 VCC S1 2 15 2OE S1 2 15 2OE 1I3 3 14 S0 1I3 3 14 S0 1I2 4 13 2I3 1I2 4 13 2I3 1I1 5 12 2I2 1I1 5 12 2I2 1I0 6 11 2I1 1I0 6 11 2I1 1Y 7 10 2I0 GND 8 9 2Y 1Y 7 GND 8 10 2I0 9 2Y CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999 1 File Number 4428 ACS253MS Die Characteristics BACKSIDE FINISH: DIE DIMENSIONS: Sapphire Size: 2390µm x 2390µm (94 mils x 94 mils) Thickness: 525µm ±25µm (20.6 mils ±1 mil) Bond Pad: 110µm x 110µm (4.3 mils x 4.3 mils) PASSIVATION: Type: Phosphorous Silicon Glass (PSG) Thickness: 1.30µm ±0.15µm METALLIZATION: Type: Al Metal 1 Thickness: 0.7µm ±0.1µm Metal 2 Thickness: 1.0µm ±0.1µm SPECIAL INSTRUCTIONS: Bond VCC First SUBSTRATE ADDITIONAL INFORMATION: Worst Case Density: <2.0 x 105 A/cm2 Transistor Count: 140 Silicon on Sapphire (SOS) SUBSTRATE POTENTIAL: Unbiased Insulator Metallization Mask Layout ACS253MS S1 10E VCC 20E 1I 3 S0 1I 2 2I 3 1I 1 2I 2 1T 0 2I 1 1Y GND 2Y 2I 0 All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com 2