MBR3100 D

MBR3100
Preferred Device
Axial Lead Rectifier
This device employs the Schottky Barrier principle in a large area
metal−to−silicon power diode. State−of−the−art geometry features
epitaxial construction with oxide passivation and metal overlap
contact. Ideally suited for use as rectifiers in low−voltage,
high−frequency inverters, free wheeling diodes, and polarity
protection diodes.
SCHOTTKY BARRIER
RECTIFIER
3.0 AMPERES, 100 VOLTS
Features
•
•
•
•
•
•
•
•
•
http://onsemi.com
Low Reverse Current
Low Stored Charge, Majority Carrier Conduction
Low Power Loss/High Efficiency
Highly Stable Oxide Passivated Junction
Guard−ring for Stress Protection
Low Forward Voltage
175°C Operating Junction Temperature
High Surge Capacity
Pb−Free Packages are Available*
AXIAL LEAD
CASE 267−05
(DO−201AD)
STYLE 1
Mechanical Characteristics:
• Case: Epoxy, Molded
• Weight: 1.1 Gram (Approximately)
• Finish: All External Surfaces Corrosion Resistant and Terminal
•
•
Leads are Readily Solderable
Lead Temperature for Soldering Purposes:
260°C Max. for 10 Seconds
Polarity: Cathode indicated by Polarity Band
MARKING DIAGRAM
A
MBR
3100
YYWWG
G
MAXIMUM RATINGS
Rating
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
Average Rectified Forward Current TA = 100°C
(RqJA = 28°C/W, Refer to P.C. Board Mounting,
Note 3)
Non−Repetitive Peak Surge Current
(Surge Applied at Rated Load Conditions
Halfwave, Single Phase, 60 Hz)
Operating and Storage Junction Temperature
Range (Note 1) (Reverse Voltage Applied)
Voltage Rate of Change (Rated VR)
Symbol
Max
Unit
VRRM
VRWM
VR
100
V
IO
3.0
A
IFSM
150
A
TJ, Tstg
−65 to
+175
°C
dv/dt
10
V/ns
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
June, 2006 − Rev. 6
ORDERING INFORMATION
Package
Shipping †
MBR3100
Axial Lead
500 Units / Bag
MBR3100G
Axial Lead
(Pb−Free)
500 Units / Bag
MBR3100RL
Axial Lead
1500/Tape & Reel
MBR3100RLG
Axial Lead
(Pb−Free)
1500/Tape & Reel
Device
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
1. The heat generated must be less than the thermal conductivity from
Junction−to−Ambient: dPD/dTJ < 1/RqJA.
© Semiconductor Components Industries, LLC, 2006
A
= Assembly Location
YY
= Year
WW
= Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
1
†For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specifications
Brochure, BRD8011/D.
Preferred devices are recommended choices for future use
and best overall value.
Publication Order Number:
MBR3100/D
MBR3100
THERMAL CHARACTERISTICS
Characteristic
Thermal Resistance, Junction−to−Ambient (see Note 3, Mounting Method 3)
Symbol
Max
Unit
RqJA
28
°C/W
Symbol
Max
Unit
ELECTRICAL CHARACTERISTICS (TL = 25°C unless otherwise noted)
Characteristic
Maximum Instantaneous Forward Voltage (Note 2)
(iF = 3.0 Amps, TL = 25°C)
(iF = 3.0 Amps, TL = 100°C)
vF
Maximum Instantaneous Reverse Current @ Rated dc Voltage (Note 2)
TL = 25°C
TL = 100°C
iR
V
0.79
0.69
mA
0.6
20
50
30
20
1
0.5
I , REVERSE CURRENT (mA)
R
i , INSTANTANEOUS FORWARD CURRENT (AMPS)
F
2. Pulse Test: Pulse Width = 300 ms, Duty Cycle = 2.0%.
TJ = 150°C
10
100°C
5
3
2
25°C
1
0.1
125°C
0.05
0.02
0.01
100°C
0.005
0.5
0.3
0.2
0.002
0.001
0.0005
0.1
0.05
TJ = 150°C
0.2
25°C
0.0002
0.0001
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 1.2 1.3
vF, INSTANTANEOUS VOLTAGE (VOLTS)
0
10
20
70
30
40
50
60
80
VR REVERSE VOLTAGE (VOLTS)
90
100
Figure 2. Typical Reverse Current*
Figure 1. Typical Forward Voltage
PF (AV), AVERAGE POWER DISSIPATION (WATTS)
I
F (AV)
, AVERAGE FORWARD CURRENT (AMPS)
*The curves shown are typical for the highest voltage device in the
voltage grouping. Typical reverse current for lower voltage selections
can be estimated from these curves if VR is sufficient below rated VR.
8
7
6
5
dc
4
SQUARE
WAVE
3
2
1
0
20
40
60
80 100 120 140 160
TA, AMBIENT TEMPERATURE (°C)
180
4
3.5
3
2.5
SQUARE
WAVE
2
1.5
1
0.5
0
Figure 3. Current Derating
(Mounting Method #3 per Note 3)
1.0
2.0
3.0
4.0
IF (AV), AVERAGE FORWARD CURRENT (AMPS)
Figure 4. Power Dissipation
http://onsemi.com
2
dc
5.0
MBR3100
400
C, CAPACITANCE (pF)
300
200
TJ = 25°C
f = 1 MHz
100
80
50
40
0
20
40
60
80
VR, REVERSE VOLTAGE (VOLTS)
Figure 5. Typical Capacitance
NOTE 3 — MOUNTING DATA
Data shown for thermal resistance junction−to−ambient
(RqJA) for the mountings shown is to be used as typical
guideline values for preliminary engineering, or in case the
tie point temperature cannot be measured.
TYPICAL VALUES FOR RqJA IN STILL AIR
Mounting
Method
Lead Length, L (in)
1/8
1/4
1/2
3/4
RqJA
1
50
51
53
55
°C/W
2
58
59
61
63
°C/W
3
°C/W
28
Mounting Method 1
Mounting Method 2
P.C. Board where available
copper surface is small.
Vector Push−In
Terminals T−28
L
ÉÉÉÉÉÉÉÉÉÉÉÉÉ
L
L
ÉÉÉÉÉÉÉÉÉÉÉ
Mounting Method 3
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
P.C. Board with
2−1/2″ X 2−1/2″
copper surface.
L = 1/2’’
Board Ground Plane
http://onsemi.com
3
L
MBR3100
PACKAGE DIMENSIONS
AXIAL LEAD
CASE 267−05
ISSUE G
K
D
A
1
2
B
K
NOTES:
1. DIMENSIONS AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 267−04 OBSOLETE, NEW STANDARD 267−05.
DIM
A
B
D
K
INCHES
MIN
MAX
0.287
0.374
0.189
0.209
0.047
0.051
1.000
−−−
MILLIMETERS
MIN
MAX
7.30
9.50
4.80
5.30
1.20
1.30
25.40
−−−
STYLE 1:
PIN 1. CATHODE (POLARITY BAND)
2. ANODE
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
4
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MBR3100/D