MC14504B D

MC14504B
Hex Level Shifter for TTL to
CMOS or CMOS to CMOS
The MC14504B is a hex non−inverting level shifter using CMOS
technology. The level shifter will shift a TTL signal to CMOS logic
levels for any CMOS supply voltage between 5 and 15 volts. A control
input also allows interface from CMOS to CMOS at one logic level to
another logic level: Either up or down level translating is
accomplished by selection of power supply levels VDD and VCC.
The VCC level sets the input signal levels while VDD selects the output
voltage levels.
Features
• UP Translates from a Low to a High Voltage or DOWN Translates
•
•
•
•
•
•
•
from a High to a Low Voltage
Input Threshold Can Be Shifted for TTL Compatibility
No Sequencing Required on Power Supplies or Inputs for Power Up
or Power Down
3 to 18 Vdc Operation for VDD and VCC
Diode Protected Inputs to VSS
Capable of Driving Two Low−Power TTL Loads or One Low−Power
Schottky TTL Load Over the Rated Temperature Range
NLV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
These Devices are Pb−Free and are RoHS Compliant
http://onsemi.com
Parameter
Unit
VCC
DC Supply Voltage Range
−0.5 to +18.0
V
VDD
DC Supply Voltage Range
−0.5 to +18.0
V
Vin
Input Voltage Range
(DC or Transient)
−0.5 to +18.0
V
Vout
Output Voltage Range
(DC or Transient)
−0.5 to VDD + 0.5
V
Input or Output Current
(DC or Transient) per Pin
±10
mA
PD
Power Dissipation, per Package
(Note 1)
500
mW
TA
Ambient Temperature Range
−55 to +125
°C
Tstg
Storage Temperature Range
−65 to +150
°C
TL
Lead Temperature
(8−Second Soldering)
260
°C
Iin, Iout
VCC
1
16
VDD
Aout
2
15
Fout
Fin
Ain
3
14
Bout
4
13
MODE
Bin
5
12
Eout
Cout
6
11
Ein
Cin
7
10
Dout
VSS
8
9
Din
MARKING DIAGRAMS
16
16
14504BG
AWLYWW
Value
TSSOP−16
DT SUFFIX
CASE 948F
PIN ASSIGNMENT
MAXIMUM RATINGS (Voltages Referenced to VSS)
Symbol
SOEIAJ−16
F SUFFIX
CASE 966
SOIC−16
D SUFFIX
CASE 751B
MC14504B
ALYWG
1
1
SOIC−16
SOEIAJ−16
16
14
504B
ALYWG
G
1
TSSOP−16
A
WL, L
YY, Y
WW, W
G or G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Indicator
(Note: Microdot may be in either location)
ORDERING INFORMATION
Stresses exceeding those listed in the Maximum Ratings table may damage the
See detailed ordering and shipping information in the package
device. If any of these limits are exceeded, device functionality should not be
dimensions section on page 2 of this data sheet.
assumed, damage may occur and reliability may be affected.
1. Temperature Derating: “D/DW” Packages: –7.0 mW/_C From 65_C To 125_C
This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be
taken to avoid applications of any voltage higher than maximum rated voltages to this high−impedance circuit. For proper operation, Vin and Vout
should be constrained to the range VSS ≤ (Vin or Vout) ≤ VDD.
Unused inputs must always be tied to an appropriate logic voltage level (e.g., either VSS or VDD). Unused outputs must be left open.
© Semiconductor Components Industries, LLC, 2014
July, 2014 − Rev. 9
1
Publication Order Number:
MC14504B/D
MC14504B
LOGIC DIAGRAM
VCC
VDD
LEVEL
SHIFTER
INPUT
OUTPUT
TTL/CMOS
MODE SELECT
MODE
Mode Select
Input Logic
Levels
Output Logic
Levels
1 (VCC)
TTL
CMOS
0 (VSS)
CMOS
CMOS
1/6 of package shown.
ORDERING INFORMATION
Device
MC14504BDG
NLV14504BDG*
MC14504BDR2G
NLV14504BDR2G*
MC14504BDTG
NLV14504BDTG*
MC14504BDTR2G
NLV14504BDTR2G*
MC14504BFELG
Package
Shipping†
SOIC−16
(Pb−Free)
48 Units / Rail
SOIC−16
(Pb−Free)
2500 Units / Tape & Reel
TSSOP−16
(Pb−Free)
96 Units / Rail
TSSOP−16
(Pb−Free)
2500 Units / Tape & Reel
SOEIAJ−16
(Pb−Free)
2000 Units / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
http://onsemi.com
2
MC14504B
ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS)
− 55_C
25_C
125_C
VCC
Vdc
VDD
Vdc
Min
Max
Min
Typ
(Note 2)
Max
Min
Max
Unit
VOL
−
−
−
5.0
10
15
−
−
−
0.05
0.05
0.05
−
−
−
0
0
0
0.05
0.05
0.05
−
−
−
0.05
0.05
0.05
Vdc
VOH
−
−
−
5.0
10
15
4.95
9.95
14.95
−
−
−
4.95
9.95
14.95
5.0
10
15
−
−
−
4.95
9.95
14.95
−
−
−
Vdc
5.0
5.0
5.0
5.0
10
10
15
10
15
15
−
−
−
−
−
0.8
0.8
1.5
1.5
3.0
−
−
−
−
−
1.3
1.3
2.25
2.25
4.5
0.8
0.8
1.5
1.5
3.0
−
−
−
−
−
0.8
0.8
1.4
1.5
2.9
5.0
5.0
5.0
5.0
10
10
15
10
15
15
2.0
2.0
3.6
3.6
7.1
−
−
−
−
−
2.0
2.0
3.5
3.5
7.0
1.5
1.5
2.75
2.75
5.5
−
−
−
−
−
2.0
2.0
3.5
3.5
7.0
−
−
−
−
−
−
−
−
−
5.0
5.0
10
15
– 3.0
– 0.64
– 1.6
– 4.2
−
−
−
−
– 2.4
– 0.51
– 1.3
– 3.4
– 4.2
– 0.88
– 2.25
– 8.8
−
−
−
−
– 1.7
– 0.36
– 0.9
– 2.4
−
−
−
−
IOL
−
−
−
5.0
10
15
0.64
1.6
4.2
−
−
−
0.51
1.3
3.4
0.88
2.25
8.8
−
−
−
0.36
0.9
2.4
−
−
−
mAdc
Input Current
Iin
−
15
−
±0.1
−
±0.00001
±0.1
−
±1.0
mAdc
Input Capacitance (Vin = 0)
Cin
−
−
−
−
−
5.0
7.5
−
−
pF
IDD or
ICC
−
−
−
5.0
10
15
−
−
−
0.05
0.10
0.20
−
−
−
0.0005
0.0010
0.0015
0.05
0.10
0.20
−
−
−
1.5
3.0
6.0
mAdc
Quiescent Current
(Per Package)
TTL−CMOS Mode
IDD
5.0
5.0
5.0
5.0
10
15
−
−
−
0.5
1.0
2.0
−
−
−
0.0005
0.0010
0.0015
0.5
1.0
2.0
−
−
−
3.8
7.5
15
mAdc
Quiescent Current
(Per Package)
TTL−CMOS Mode
ICC
5.0
5.0
5.0
5.0
10
15
−
−
−
5.0
5.0
5.0
−
−
−
2.5
2.5
2.5
5.0
5.0
5.0
−
−
−
6.0
6.0
6.0
mAdc
Characteristic
Output Voltage
Vin = 0 V
Symbol
“0” Level
“1” Level
Vin = VCC
Input Voltage
“0” Level
(VOL = 1.0 Vdc) TTL−CMOS
(VOL = 1.5 Vdc) TTL−CMOS
(VOL = 1.0 Vdc) CMOS−CMOS
(VOL = 1.5 Vdc) CMOS−CMOS
(VOL = 1.5 Vdc) CMOS−CMOS
VIL
Input Voltage
“1” Level
(VOH = 9.0 Vdc) TTL−CMOS
(VOH = 13.5 Vdc) TTL−CMOS
(VOH = 9.0 Vdc) CMOS−CMOS
(VOH = 13.5 Vdc) CMOS−CMOS
(VOH = 13.5 Vdc) CMOS−CMOS
VIH
Output Drive Current
(VOH = 2.5 Vdc)
(VOH = 4.6 Vdc)
(VOH = 9.5 Vdc)
(VOH = 13.5 Vdc)
IOH
(VOL = 0.4 Vdc)
(VOL = 0.5 Vdc)
(VOL = 1.5 Vdc)
Quiescent Current
(Per Package)
CMOS−CMOS Mode
Source
Sink
Vdc
Vdc
mAdc
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
2. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
http://onsemi.com
3
MC14504B
SWITCHING CHARACTERISTICS (CL = 50 pF, TA = 25_C)
Characteristic
Propagation Delay, High to Low
Symbol
Shifting Mode
VCC
Vdc
VDD
Vdc
Min
Limits
Typ
(Note 3)
Max
Unit
tPHL
TTL – CMOS
VDD > VCC
5.0
5.0
10
15
−
−
140
140
280
280
ns
CMOS – CMOS
VDD > VCC
5.0
5.0
10
10
15
15
5.0
5.0
10
15
15
5.0
5.0
10
10
15
−
−
−
−
−
−
−
−
120
120
70
185
185
175
170
160
240
240
140
370
370
350
340
320
5.0
5.0
10
10
15
15
−
−
−
10
15
15
5.0
5.0
10
5.0
10
15
−
−
−
−
−
−
−
−
−
170
170
100
275
275
145
100
50
40
340
340
200
550
550
290
200
100
80
CMOS – CMOS
VCC > VDD
Propagation Delay, Low to High
tPLH
TTL – CMOS
VDD > VCC
CMOS – CMOS
VDD > VCC
CMOS – CMOS
VCC > VDD
Output Rise and Fall Time
tTLH, tTHL
ALL
ns
ns
3. Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
7
VSp , INPUT SWITCHPOINT VOLTAGE (Vdc)
VSp , INPUT SWITCHPOINT VOLTAGE (Vdc)
7
6
VCC = 10 V
5
4
3
VCC = 5 V
2
1
6
5
4
3
2
1
0
0
0
5
10
15
VDD, SUPPLY VOLTAGE (Vdc)
20
0
Figure 1. Input Switchpoint CMOS to CMOS Mode
20
20
ÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉ
15
10
5
5
10
15
VDD, SUPPLY VOLTAGE (Vdc)
20
Figure 2. Input Switchpoint TTL to CMOS Mode
VDD, SUPPLY VOLTAGE (Vdc)
VDD, SUPPLY VOLTAGE (Vdc)
VCC = 5 V
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
15
10
0
5
0
0
5
10
15
VCC, SUPPLY VOLTAGE (Vdc)
20
0
Figure 3. Operating Boundary CMOS to CMOS Mode
5
10
15
VCC, SUPPLY VOLTAGE (Vdc)
20
Figure 4. Operating Boundary TTL to CMOS Mode
http://onsemi.com
4
MC14504B
PACKAGE DIMENSIONS
TSSOP−16
DT SUFFIX
PLASTIC TSSOP PACKAGE
CASE 948F
ISSUE B
16X K REF
0.10 (0.004)
0.15 (0.006) T U
T U
M
S
V
S
ÇÇÇ
ÇÇÇ
ÉÉÉ
ÇÇÇ
ÉÉÉ
S
K
K1
2X
L/2
16
9
J1
B
−U−
L
SECTION N−N
J
PIN 1
IDENT.
N
0.25 (0.010)
8
1
M
0.15 (0.006) T U
S
A
−V−
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH. PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE
DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08
(0.003) TOTAL IN EXCESS OF THE K
DIMENSION AT MAXIMUM MATERIAL
CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
N
F
DETAIL E
−W−
C
0.10 (0.004)
−T− SEATING
PLANE
H
D
DETAIL E
G
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
SOLDERING FOOTPRINT
7.06
1
0.65
PITCH
16X
0.36
16X
1.26
DIMENSIONS: MILLIMETERS
http://onsemi.com
5
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
−−−
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.18
0.28
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN
MAX
0.193 0.200
0.169 0.177
−−− 0.047
0.002 0.006
0.020 0.030
0.026 BSC
0.007
0.011
0.004 0.008
0.004 0.006
0.007 0.012
0.007 0.010
0.252 BSC
0_
8_
MC14504B
PACKAGE DIMENSIONS
SOIC−16
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751B−05
ISSUE K
−A−
16
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR PROTRUSION
SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D
DIMENSION AT MAXIMUM MATERIAL CONDITION.
9
−B−
1
P
8 PL
0.25 (0.010)
8
M
B
S
G
R
K
F
X 45 _
C
−T−
SEATING
PLANE
J
M
D
16 PL
0.25 (0.010)
M
T B
S
A
S
SOLDERING FOOTPRINT
8X
6.40
16X
1
1.12
16
16X
0.58
1.27
PITCH
8
9
DIMENSIONS: MILLIMETERS
http://onsemi.com
6
DIM
A
B
C
D
F
G
J
K
M
P
R
MILLIMETERS
MIN
MAX
9.80
10.00
3.80
4.00
1.35
1.75
0.35
0.49
0.40
1.25
1.27 BSC
0.19
0.25
0.10
0.25
0_
7_
5.80
6.20
0.25
0.50
INCHES
MIN
MAX
0.386
0.393
0.150
0.157
0.054
0.068
0.014
0.019
0.016
0.049
0.050 BSC
0.008
0.009
0.004
0.009
0_
7_
0.229
0.244
0.010
0.019
MC14504B
PACKAGE DIMENSIONS
SOEIAJ−16
F SUFFIX
PLASTIC EIAJ SOIC PACKAGE
CASE 966
ISSUE A
16
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS D AND E DO NOT INCLUDE
MOLD FLASH OR PROTRUSIONS AND ARE
MEASURED AT THE PARTING LINE. MOLD FLASH
OR PROTRUSIONS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
4. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
5. THE LEAD WIDTH DIMENSION (b) DOES NOT
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSIONS AND ADJACENT LEAD
TO BE 0.46 ( 0.018).
LE
9
Q1
M_
E HE
1
L
8
DETAIL P
Z
D
e
VIEW P
A
A1
b
0.13 (0.005)
c
M
0.10 (0.004)
DIM
A
A1
b
c
D
E
e
HE
L
LE
M
Q1
Z
MILLIMETERS
MIN
MAX
--2.05
0.05
0.20
0.35
0.50
0.10
0.20
9.90
10.50
5.10
5.45
1.27 BSC
7.40
8.20
0.50
0.85
1.10
1.50
10 _
0_
0.70
0.90
--0.78
INCHES
MIN
MAX
--0.081
0.002
0.008
0.014
0.020
0.007
0.011
0.390
0.413
0.201
0.215
0.050 BSC
0.291
0.323
0.020
0.033
0.043
0.059
10 _
0_
0.028
0.035
--0.031
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
7
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
MC14504B/D