LMV321 LMV358 LMV324 D

LMV321, LMV358, LMV324
Single, Dual, Quad
Low-Voltage, Rail-to-Rail
Operational Amplifiers
The LMV321, LMV358, and LMV324 are CMOS single, dual, and
quad low voltage operational amplifiers with rail−to−rail output
swing. These amplifiers are a cost−effective solution for applications
where low power consumption and space saving packages are critical.
Specification tables are provided for operation from power supply
voltages at 2.7 V and 5 V. Rail−to−Rail operation provides improved
signal−to−noise preformance. Ultra low quiescent current makes this
series of amplifiers ideal for portable, battery operated equipment. The
common mode input range includes ground making the device useful
for low−side current−shunt measurements. The ultra small packages
allow for placement on the PCB in close proximity to the signal source
thereby reducing noise pickup.
www.onsemi.com
5
1
1
TSOP−5
CASE 483
SC−70
CASE 419A
1
Micro8]
CASE 846A
Features
•
•
•
•
•
•
•
•
Operation from 2.7 V to 5.0 V Single−Sided Power Supply
LMV321 Single Available in Ultra Small 5 Pin SC70 Package
No Output Crossover Distortion
Industrial temperature Range: −40°C to +85°C
Rail−to−Rail Output
Low Quiescent Current: LMV358 Dual − 220 mA, Max per Channel
No Output Phase−Reversal from Overdriven Input
These are Pb−Free Devices
8
8
1
SOIC−8
CASE 751
1
UDFN8
CASE 517AJ
1
1
SOIC−14
CASE 751A
TSSOP−14
CASE 948G
Typical Applications
• Notebook Computers and PDA’s
• Portable Battery−Operated Instruments
• Active Filters
ORDERING AND MARKING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 12 of this data sheet.
120
80
100
70
CMRR (dB)
GAIN (dB)
80
60
40
60
VS = 5 V
50
20
40
Over −40°C to +85°C
Same Gain $1.8 dB (Typ)
0
−20
10
100
1k
10k
100k
FREQUENCY (Hz)
1M
10M
Figure 1. Open Loop Frequency Response
(RL = 2 kW, TA = 255C, VS = 5 V)
© Semiconductor Components Industries, LLC, 2015
February, 2015 − Rev. 12
30
−1
0
1
2
3
4
INPUT COMMON MODE VOLTAGE (V)
5
Figure 2. CMRR vs. Input Common Mode
Voltage
1
Publication Order Number:
LMV321/D
LMV321, LMV358, LMV324
MARKING DIAGRAMS
SC−70
Micro8
TSOP−5
8
5
V358
AYWG
G
3ACAYWG
G
AAC MG
G
1
AAC
= Specific Device Code
M
= Date Code
G
= Pb−Free Package
(Note: Microdot may be in either location)
1
3AC = Specific Device Code
A
= Assembly Location
Y
= Year
W = Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
V358
= Specific Device Code
A
= Assembly Location
Y
= Year
W
= Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
SOIC−8
UDFN8
8
V358
ALYW
G
AC M
G
1
= Specific Device Code
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
V358
A
L
Y
W
G
AC = Specific Device Code
M = Date Code
G
= Pb−Free Package
SOIC−14
TSSOP−14
14
14
LMV
324
ALYW
LMV324
AWLYWWG
1
1
LMV324 = Specific Device Code
A
= Assembly Location
WL
= Wafer Lot
Y
= Year
WW
= Work Week
G
= Pb−Free Package
LMV324 = Specific Device Code
A
= Assembly Location
L
= Wafer Lot
Y
= Year
W
= Work Week
G
= Pb−Free Package
PIN CONNECTIONS
V+
+IN
2
IN A−
+
−
V−
3
4
−IN
IN A+
2
A
− +
7 OUT B
6 IN B−
3
B
+ −
OUTPUT
V−
5 IN B+
4
13 IN D−
IN A−
2
3
12 IN D+
IN A+
3
12 IN D+
4
11 V−
V+
4
11 V−
5
10 IN C+
IN B+
5
10 IN C+
6
9
IN B−
6
2
IN A+
V+
OUT B
(Top View)
1
IN A−
IN B−
(Top View)
A
− +
D
+ −
B
C
7
(Top View)
www.onsemi.com
2
TSSOP−14
OUT A
1
IN B+
SOIC−14
14 OUT D
OUT A
+ −
8 V+
1
− +
UDFN8/Micro8/SOIC−8
OUT A
5
8
IN C−
OUT C
OUT B
7
A
− +
D
+ −
+ −
1
− +
SC70−5/TSOP−5
B
C
(Top View)
14 OUT D
13 IN D−
9
IN C−
8
OUT C
LMV321, LMV358, LMV324
MAXIMUM RATINGS
Symbol
VS
Rating
Supply Voltage (Operating Range VS = 2.7 V to 5.5 V)
Value
Unit
5.5
V
VIDR
Input Differential Voltage
$Supply Voltage
V
VICR
Input Common Mode Voltage Range
−0.5 to (V+) + 0.5
V
10
mA
Maximum Input Current
tSo
Output Short Circuit (Note 1)
TJ
Maximum Junction Temperature (Operating Range −40°C to 85°C)
qJA
Thermal Resistance:
Tstg
Continuous
°C
°C/W
SC−70
280
Micro8
238
TSOP−5
333
UDFN8 (1.2 mm x 1.8 mm x 0.5 mm)
350
SOIC−8
212
SOIC−14
156
TSSOP−14
190
Storage Temperature
Mounting Temperature (Infrared or Convection −20 sec)
VESD
150
ESD Tolerance
LMV321
Machine Model
Human Body Model
LMV358/324
Machine Model
Human Body Mode
−65 to 150
°C
260
°C
V
100
1000
100
2000
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device
functionality should not be assumed, damage may occur and reliability may be affected.
1. Continuous short−circuit operation to ground at elevated ambient temperature can result in exceeding the maximum allowed junction
temperature of 150°C. Output currents in excess of 45 mA over long term may adversely affect reliability. Shorting output to either V+
or V− will adversely affect reliability.
www.onsemi.com
3
LMV321, LMV358, LMV324
2.7 V DC ELECTRICAL CHARACTERISTICS (Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 2.7 V,
RL = 1 MW, V− = 0 V, VO = V+/2)
Parameter
Input Offset Voltage
Input Offset Voltage Average Drift
Symbol
Condition
VIO
ICVOS
Min
Typ
Max
Unit
TA = −40°C to +85°C
1.7
9
mV
TA = −40°C to +85°C
5
mV/°C
Input Bias Current
IB
TA = −40°C to +85°C
<1
nA
Input Offset Current
IIO
TA = −40°C to +85°C
<1
nA
Common Mode Rejection Ratio
CMRR
0 V v VCM v 1.7 V
50
63
dB
Power Supply Rejection Ratio
PSRR
2.7 V v V+ v 5 V,
VO = 1 V
50
60
dB
Input Common−Mode Voltage Range
VCM
For CMRR w 50 dB
0 to 1.7
−0.2 to 1.9
V
Output Swing
VOH
RL = 10 kW to 1.35 V
VCC − 100
VCC − 10
mV
VOL
RL = 10 kW to 1.35 V (Note 2)
Supply Current
LMV321
LMV358 (Both Amplifiers)
LMV324 (4 Amplifiers)
ICC
60
180
mV
80
140
260
185
340
680
mA
2.7 V AC ELECTRICAL CHARACTERISTICS (Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 2.7 V,
RL = 1 MW, V− = 0 V, VO = V+/2)
Parameter
Gain Bandwidth Product
Symbol
Condition
GBWP
CL = 200 pF
Phase Margin
Qm
Gain Margin
Gm
Input−Referred Voltage Noise
en
f = 50 kHz
Min
Typ
Max
Unit
1
MHz
60
°
10
dB
50
nV/√Hz
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
2. Guaranteed by design and/or characterization.
www.onsemi.com
4
LMV321, LMV358, LMV324
5.0 V DC ELECTRICAL CHARACTERISTICS (Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 5.0 V,
RL = 1 MW, V− = 0 V, VO = V+/2)
Parameter
Input Offset Voltage
Input Offset Voltage Average Drift
Input Bias Current (Note 3)
Symbol
Condition
VIO
TCVIO
Min
Typ
Max
Unit
TA = −40°C to +85°C
1.7
9
mV
TA = −40°C to +85°C
5
mV/°C
<1
nA
<1
nA
IB
TA = −40°C to +85°C
Input Offset Current (Note 3)
IIO
TA = −40°C to +85°C
Common Mode Rejection Ratio
CMRR
0 V v VCM v 4 V
50
65
dB
Power Supply Rejection Ratio
PSRR
2.7 V v V+ v 5 V,
VO = 1 V, VCM = 1 V
50
60
dB
VCM
For CMRR w 50 dB
0 to 4
−0.2 to 4.2
V
AV
RL = 2 kW
15
100
V/mV
TA = −40°C to +85°C
10
VOH
RL = 2 kW to 2.5 V
TA = −40°C to +85°C
VCC − 300
VCC − 400
VCC − 40
mV
VOL
RL = 2 kW to 2.5 V (Note 3)
TA = −40°C to +85°C
VOH
RL = 10 kW to 2.5 V (Note 3)
TA = −40°C to +85°C
VOL
RL = 10 kW to 2.5 V
TA = −40°C to +85°C
Output Short Circuit Current
IO
Sourcing = VO = 0 V (Note 3)
Sinking = VO = 5 V (Note 3)
Supply Current
ICC
LMV321
TA = −40°C to +85°C
130
250
350
LMV358 Both Amplifiers
TA = −40°C to +85°C
210
440
615
LMV324 All Four Amplifiers
TA = −40°C to +85°C
410
830
1160
Input Common−Mode Voltage Range
Large Signal Voltage Gain (Note 3)
Output Swing
120
300
400
VCC − 100
VCC − 200
mV
65
10
10
mV
180
280
60
160
mV
mA
mA
5.0 V AC ELECTRICAL CHARACTERISTICS (Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 5.0 V,
RL = 1 MW, V− = 0 V, VO = V+/2)
Parameter
Slew Rate
Gain Bandwidth Product
Symbol
Condition
SR
GBWP
CL = 200 pF
Min
Typ
Max
Unit
1
V/ms
1
MHz
Phase Margin
Qm
60
°
Gain Margin
Gm
10
dB
Input−Referred Voltage Noise
en
50
nV/√Hz
f = 50 kHz
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
3. Guaranteed by design and/or characterization.
www.onsemi.com
5
LMV321, LMV358, LMV324
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
120
170
100
150
60
40
20
0
−20
10
130
PHASE MARGIN (°)
GAIN (dB)
80
110
90
70
50
Over −40°C to +85°C
Same Gain $1.8 dB (Typ)
30
10
100
1k
10k
100k
FREQUENCY (Hz)
10M
1M
10
90
75
80
70
70
65
CMRR (dB)
CMRR (dB)
80
60
50
40
100k
1M
10M
60
55
45
20
40
10
35
10k
30
−0.5
100k
VS = 2.7 V
f = 10 kHz
50
30
1k
10k
Figure 4. Open Loop Phase Margin
(RL = 2 kW, TA = 255C, VS = 5 V)
100
100
1k
FREQUENCY (Hz)
Figure 3. Open Loop Frequency Response
(RL = 2 kW, TA = 255C, VS = 5 V)
0
10
100
0
0.5
1
1.5
2
2.5
FREQUENCY (Hz)
INPUT COMMON MODE VOLTAGE (V)
Figure 5. CMRR vs. Frequency
(RL = 5 kW, VS = 5 V)
Figure 6. CMRR vs. Input Common Mode
Voltage
80
3
100
90
70
80
60
PSRR (dB)
CMRR (dB)
70
VS = 5 V
f = 10 kHz
50
60
50
40
30
20
40
10
30
−1
0
1
2
3
4
0
1k
5
10k
100k
1M
INPUT COMMON MODE VOLTAGE (V)
FREQUENCY (Hz)
Figure 7. CMRR vs. Input Common Mode
Voltage
Figure 8. PSRR vs. Frequency
(RL = 5 kW, VS = 2.7 V, +PSRR)
www.onsemi.com
6
10M
LMV321, LMV358, LMV324
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
90
100
80
90
70
80
70
PSRR (dB)
PSRR (dB)
60
50
40
30
40
30
20
10
10
10k
100k
1M
0
1k
10M
10k
100k
1M
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 9. PSRR vs. Frequency
(RL = 5 kW, VS = 2.7 V, −PSRR)
Figure 10. PSRR vs. Frequency
(RL = 5 kW, VS = 5 V, +PSRR)
100
5
90
4.5
80
4
70
3.5
60
3
VOS (mV)
PSRR (dB)
50
20
0
1k
50
40
2.5
2
30
1.5
20
1
10
0.5
VS = 2.7 V
0
0
1k
10k
100k
1M
0
10M
0.5
1
1.5
2
2.5
FREQUENCY (Hz)
VCM (V)
Figure 11. PSRR vs. Frequency
(RL = 5 kW, VS = 5 V, −PSRR)
Figure 12. VOS vs CMR
200
180
4
160
SUPPLY CURRENT (mA)
5
4.5
3.5
VOS (mV)
60
3
2.5
2
1.5
1
VS = 5.0 V
0.5
3
140
120
100
80
60
40
20
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
0
0
5
0.5
1
1.5
2
2.5
3
3.5
4
4.5
VCM (V)
SUPPLY VOLTAGE (V)
Figure 13. VOS vs CMR
Figure 14. Supply Current vs. Supply Voltage
www.onsemi.com
7
5
LMV321, LMV358, LMV324
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
1
0
(%)
0.1
0.01
100
1k
10k
−0.03
−0.04
−0.05
−0.06
−0.07
−0.08
−0.09
−0.1
2.5
3.5
4
4.5
5
SUPPLY VOLTAGE (V)
Figure 15. THD+N vs Frequency
Figure 16. Output Voltage Swing vs Supply
Voltage (RL = 10k)
0
0.09
−20
0.08
0.07
0.06
0.05
0.04
0.03
0.02
−60
−80
−100
−120
−140
Negative Swing
0.01
−40
−160
3
3.5
4
SUPPLY VOLTAGE (V)
4.5
5
0
0.5
1
1.5
2
2.5
VOUT REFERENCED TO V− (V)
Figure 17. Output Voltage Swing vs Supply
Voltage (RL = 10k)
Figure 18. Sink Current vs. Output Voltage
VS = 2.7 V
0
120
−20
100
SOURCE CURRENT (mA)
SINK CURRENT (mA)
3
(Hz)
0.1
0
2.5
Positive Swing
−0.02
100k
SINK CURRENT (mA)
VOUT REFERENCED TO V− (V)
0.001
10
−0.01
VOUT REFERENCED TO V+ (V)
RL = 10 kW
Vout = 1 VPP
Av = +1
−40
−60
−80
−100
−120
80
60
40
20
0
0
1
2
3
4
5
VOUT REFERENCED TO V− (V)
0
0.5
1.0
1.5
2.0
VOUT REFERENCED TO V+ (V)
Figure 19. Sink Current vs. Output Voltage
VS = 5.0 V
Figure 20. Source Current vs. Output Voltage
VS = 2.7 V
www.onsemi.com
8
2.5
LMV321, LMV358, LMV324
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
110
RL = 2 kW
AV = 1
50 mV/div
2 ms/div
SOURCE CURRENT (mA)
100
90
80
70
60
50
40
30
20
10
0
0
1
2
3
4
VOUT REFERENCED TO V+ (V)
5
Figure 21. Source Current vs. Output Voltage
VS = 5.0 V
Figure 22. Settling Time vs. Capacitive Load
50 mV/div
2 ms/div
RL = 1 MW
AV = 1
50 mV/div
2 ms/div
Non−Inverting (G = +1)
Input
Output
Figure 23. Settling Time vs. Capacitive Load
Figure 24. Step Response − Small Signal
50 mV/div
2 ms/div
1 V/div
2 ms/div
Non−Inverting (G = +1)
Inverting (G = −1)
Input
Input
Output
Output
Figure 26. Step Response − Large Signal
Figure 25. Step Response − Small Signal
www.onsemi.com
9
LMV321, LMV358, LMV324
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
1 V/div
2 ms/div
Inverting (G = −1)
Input
Output
Figure 27. Step Response − Large Signal
www.onsemi.com
10
LMV321, LMV358, LMV324
APPLICATIONS
50 k
R1
5.0 k
VCC
VCC
R2
10 k
MC1403
VO
LMV321
VO
LMV321
VCC
−
Vref
−
+
+
fO +
1
V ref + V CC
2
2.5 V
R
R1
V O + 2.5 V(1 )
)
R2
R
Figure 28. Voltage Reference
C
C
1
2pRC
For: fo = 1.0 kHz
R = 16 kW
C = 0.01 mF
Figure 29. Wien Bridge Oscillator
VCC
C
R1
R3
C
−
Vin
R2
CO
VO
LMV321
Hysteresis
R2
VOH
R1
+
Vref
VO
Vref
+
Vin
LMV321
−
VO
VOL
CO = 10 C
VinL
Given: fo = center frequency
A(fo) = gain at center frequency
VinH
Choose value fo, C
Q
Then : R3 +
pf O C
Vref
R1
(V OL * V ref) ) V ref
R1 ) R2
R1
V inH +
(V OH * V ref) ) V ref
R1 ) R2
R1
H+
(V OH * V OL)
R1 ) R2
V inL +
R1 +
R2 +
R3
2 A(f O)
R1 R3
4Q 2 R1 * R3
Figure 30. Comparator with Hysteresis
For less than 10% error from operational amplifier,
((QO fO)/BW) < 0.1 where fo and BW are expressed in Hz.
If source impedance varies, filter may be preceded with
voltage follower buffer to stabilize filter parameters.
Figure 31. Multiple Feedback Bandpass Filter
www.onsemi.com
11
LMV321, LMV358, LMV324
ORDERING INFORMATION
Number
of
Channels
Specific Device Marking
Package Type
Shipping†
Single
AAC
SC−70
(Pb−Free)
3000 / Tape & Reel
LMV321SN3T1G
Single
3AC
TSOP−5
(Pb−Free)
3000 / Tape & Reel
LMV358DMR2G
Dual
V358
Micro8
(Pb−Free)
4000 / Tape & Reel
LMV358MUTAG
Dual
AC
UDFN8
(Pb−Free)
3000 / Tape & Reel
LMV358DR2G
Dual
V358
SOIC−8
(Pb−Free)
2500 / Tape & Reel
LMV324DR2G
Quad
LMV324
SOIC−14
(Pb−Free)
2500 / Tape & Reel
LMV324DTBR2G
Quad
LMV
324
TSSOP−14
(Pb−Free)
2500 / Tape & Reel
Order Number
LMV321SQ3T2G
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
12
LMV321, LMV358, LMV324
PACKAGE DIMENSIONS
SC−88A (SC−70−5/SOT−353)
CASE 419A−02
ISSUE L
A
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 419A−01 OBSOLETE. NEW STANDARD
419A−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
G
5
4
−B−
S
1
2
DIM
A
B
C
D
G
H
J
K
N
S
3
D 5 PL
0.2 (0.008)
B
M
M
N
J
C
K
H
SOLDER FOOTPRINT
0.50
0.0197
0.65
0.025
0.65
0.025
0.40
0.0157
1.9
0.0748
www.onsemi.com
13
SCALE 20:1
mm Ǔ
ǒinches
INCHES
MIN
MAX
0.071
0.087
0.045
0.053
0.031
0.043
0.004
0.012
0.026 BSC
--0.004
0.004
0.010
0.004
0.012
0.008 REF
0.079
0.087
MILLIMETERS
MIN
MAX
1.80
2.20
1.15
1.35
0.80
1.10
0.10
0.30
0.65 BSC
--0.10
0.10
0.25
0.10
0.30
0.20 REF
2.00
2.20
LMV321, LMV358, LMV324
PACKAGE DIMENSIONS
TSOP−5
CASE 483−02
ISSUE K
NOTE 5
2X
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH
THICKNESS. MINIMUM LEAD THICKNESS IS THE
MINIMUM THICKNESS OF BASE MATERIAL.
4. DIMENSIONS A AND B DO NOT INCLUDE MOLD
FLASH, PROTRUSIONS, OR GATE BURRS. MOLD
FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT
EXCEED 0.15 PER SIDE. DIMENSION A.
5. OPTIONAL CONSTRUCTION: AN ADDITIONAL
TRIMMED LEAD IS ALLOWED IN THIS LOCATION.
TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2
FROM BODY.
D 5X
0.20 C A B
0.10 T
M
2X
0.20 T
B
5
1
4
2
S
3
K
B
DETAIL Z
G
A
A
TOP VIEW
DIM
A
B
C
D
G
H
J
K
M
S
DETAIL Z
J
C
0.05
H
SIDE VIEW
C
SEATING
PLANE
END VIEW
MILLIMETERS
MIN
MAX
3.00 BSC
1.50 BSC
0.90
1.10
0.25
0.50
0.95 BSC
0.01
0.10
0.10
0.26
0.20
0.60
0_
10 _
2.50
3.00
SOLDERING FOOTPRINT*
0.95
0.037
1.9
0.074
2.4
0.094
1.0
0.039
0.7
0.028
SCALE 10:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
14
LMV321, LMV358, LMV324
PACKAGE DIMENSIONS
Micro8™
CASE 846A−02
ISSUE J
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED
0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5. 846A-01 OBSOLETE, NEW STANDARD 846A-02.
D
HE
PIN 1 ID
E
e
b 8 PL
0.08 (0.003)
−T−
DIM
A
A1
b
c
D
E
e
L
HE
M
T B
S
A
S
SEATING
PLANE
MILLIMETERS
NOM
MAX
−−
1.10
0.08
0.15
0.33
0.40
0.18
0.23
3.00
3.10
3.00
3.10
0.65 BSC
0.40
0.55
0.70
4.75
4.90
5.05
MIN
−−
0.05
0.25
0.13
2.90
2.90
A
0.038 (0.0015)
A1
L
c
RECOMMENDED
SOLDERING FOOTPRINT*
8X
8X
0.48
0.80
5.25
0.65
PITCH
DIMENSION: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
15
INCHES
NOM
−−
0.003
0.013
0.007
0.118
0.118
0.026 BSC
0.021
0.016
0.187
0.193
MIN
−−
0.002
0.010
0.005
0.114
0.114
MAX
0.043
0.006
0.016
0.009
0.122
0.122
0.028
0.199
LMV321, LMV358, LMV324
PACKAGE DIMENSIONS
UDFN8 1.8x1.2, 0.4P
CASE 517AJ
ISSUE O
PIN ONE
REFERENCE
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30 mm FROM TERMINAL TIP.
4. MOLD FLASH ALLOWED ON TERMINALS
ALONG EDGE OF PACKAGE. FLASH MAY
NOT EXCEED 0.03 ONTO BOTTOM
SURFACE OF TERMINALS.
5. DETAIL A SHOWS OPTIONAL
CONSTRUCTION FOR TERMINALS.
A B
D
0.10 C
ÉÉ
ÉÉ
L1
E
DETAIL A
NOTE 5
0.10 C
TOP VIEW
(A3)
0.05 C
DIM
A
A1
A3
b
b2
D
E
e
L
L1
L2
A
0.05 C
SIDE VIEW
A1
e/2
e
(b2)
C
DETAIL A
8X
1
SEATING
PLANE
L
4
MILLIMETERS
MIN
MAX
0.45
0.55
0.00
0.05
0.127 REF
0.15
0.25
0.30 REF
1.80 BSC
1.20 BSC
0.40 BSC
0.45
0.55
0.00
0.03
0.40 REF
MOUNTING FOOTPRINT*
SOLDERMASK DEFINED
(L2)
8
5
BOTTOM VIEW
8X
8X b
0.66
7X
0.10
M
C A B
0.05
M
C
0.22
NOTE 3
1.50
1
0.32
0.40 PITCH
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
16
LMV321, LMV358, LMV324
PACKAGE DIMENSIONS
SOIC−8 NB
CASE 751−07
ISSUE AK
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
−X−
A
8
5
S
B
0.25 (0.010)
M
Y
M
1
4
K
−Y−
G
C
N
DIM
A
B
C
D
G
H
J
K
M
N
S
X 45 _
SEATING
PLANE
−Z−
0.10 (0.004)
H
M
D
0.25 (0.010)
M
Z Y
S
X
S
J
SOLDERING FOOTPRINT*
1.52
0.060
7.0
0.275
4.0
0.155
0.6
0.024
1.270
0.050
SCALE 6:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
17
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0_
8_
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0 _
8 _
0.010
0.020
0.228
0.244
LMV321, LMV358, LMV324
PACKAGE DIMENSIONS
SOIC−14 NB
CASE 751A−03
ISSUE K
D
A
B
14
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE PROTRUSION
SHALL BE 0.13 TOTAL IN EXCESS OF AT
MAXIMUM MATERIAL CONDITION.
4. DIMENSIONS D AND E DO NOT INCLUDE
MOLD PROTRUSIONS.
5. MAXIMUM MOLD PROTRUSION 0.15 PER
SIDE.
8
A3
E
H
L
1
0.25
M
DETAIL A
7
B
13X
M
b
0.25
M
C A
S
B
S
e
DETAIL A
h
A
X 45 _
M
A1
C
SEATING
PLANE
DIM
A
A1
A3
b
D
E
e
H
h
L
M
MILLIMETERS
MIN
MAX
1.35
1.75
0.10
0.25
0.19
0.25
0.35
0.49
8.55
8.75
3.80
4.00
1.27 BSC
5.80
6.20
0.25
0.50
0.40
1.25
0_
7_
SOLDERING FOOTPRINT*
6.50
14X
1.18
1
1.27
PITCH
14X
0.58
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
18
INCHES
MIN
MAX
0.054 0.068
0.004 0.010
0.008 0.010
0.014 0.019
0.337 0.344
0.150 0.157
0.050 BSC
0.228 0.244
0.010 0.019
0.016 0.049
0_
7_
LMV321, LMV358, LMV324
PACKAGE DIMENSIONS
TSSOP−14
CASE 948G
ISSUE B
14X K REF
0.10 (0.004)
0.15 (0.006) T U
T U
M
V
S
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL
IN EXCESS OF THE K DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
S
S
N
2X
14
L/2
0.25 (0.010)
8
M
B
−U−
L
PIN 1
IDENT.
F
7
1
0.15 (0.006) T U
N
S
DETAIL E
K
A
−V−
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
K1
J J1
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
SECTION N−N
−W−
C
0.10 (0.004)
−T− SEATING
PLANE
D
H
G
DETAIL E
SOLDERING FOOTPRINT*
7.06
1
0.65
PITCH
14X
0.36
14X
1.26
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
www.onsemi.com
19
MILLIMETERS
INCHES
MIN
MAX
MIN MAX
4.90
5.10 0.193 0.200
4.30
4.50 0.169 0.177
−−−
1.20
−−− 0.047
0.05
0.15 0.002 0.006
0.50
0.75 0.020 0.030
0.65 BSC
0.026 BSC
0.50
0.60 0.020 0.024
0.09
0.20 0.004 0.008
0.09
0.16 0.004 0.006
0.19
0.30 0.007 0.012
0.19
0.25 0.007 0.010
6.40 BSC
0.252 BSC
0_
8_
0_
8_
LMV321, LMV358, LMV324
Micro8 is a trademark of International Rectifier.
ON Semiconductor and the
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
www.onsemi.com
20
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
LMV321/D