ISO1H801G Data Sheet (1.1 MB, EN)

Datasheet, Version 2.3, September 2009
ISOFACE
TM
ISO1H801G
Coreless Transformer Isolated
Digital Output 8 Channel 0.625A
High-Side Switch
Power Management & Drives
N e v e r
s t o p
t h i n k i n g .
ISO1H801G
Revision History:
2009-09-16
Previous Version:
V2.2
V2.0
Final Datasheet
V2.1
Final Datasheet
V2.2
Page 15 creepage, clearance distance and VISO adapted,
V2.3
Diagnostic output discontinued
Version 2.3
Edition 2009-09-16
Published by Infineon Technologies AG,
Am Campeon 1-12,
85579 Neubiberg, Germany
© Infineon Technologies AG 2009.
All Rights Reserved.
Attention please!
The information herein is given to describe certain components and shall not be considered as a guarantee of
characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding
circuits, descriptions and charts stated herein.
Information
For further information on technology, delivery terms and conditions and prices please contact your nearest
Infineon Technologies Office (www.infineon.com).
Warnings
Due to technical requirements components may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devices or systems with the express written
approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure
of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
ISOFACETM
ISO1H801G
Coreless Transformer Isolated Digital
Output 8 Channel 0.625A High-Side Switch
Product Highlights
•
•
•
•
Coreless transformer isolated data interface
Galvanic isolation
8 High-side output switches 0.625A
µC compatible 8-bit parallel peripheral
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Interface 5V CMOS operation compatible
Parallel interface
Direct control mode
High common mode transient immunity
Short circuit protection
Maximum current internally limited
Overload protection
Overvoltage protection (including load dump)
Undervoltage shutdown with autorestart and
hysteresis
Switching inductive loads
Common output disable pin
Thermal shutdown with restart
Thermal independence of separate channels
ESD protection
Loss of GNDbb and loss of Vbb protection
Reverse Output Voltage protection
•
Isolated switch for industrial applications (PLC)
All types of resistive, inductive and capacitive loads
µC compatible power switch for 24V DC
applications
Driver for solenoid, relays and resistive loads
Description
The ISO1H801G is a galvanically isolated 8 bit data
interface in PG-DSO-36 package that provides 8 fully
protected high-side power switches that are able to
handle currents up to 625 mA.
An 8 bit parallel µC compatible interface allows to
connect the IC directly to a µC system. The input
interface supports also a direct control mode and is
designed to operate with 5V CMOS compatible levels.
The data transfer from input to output side is realized by
the integrated Coreless Transformer Technology.
Typical Application
Typical Application
VCC
VCC
VCCP1.x
DIS
AD0
CS
WR
WR
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
µC (i.e
C166)
D0
D1
D2
D3
D4
D5
D6
D7
Vbb
Vbb
CT
Control
Unit
OUT0
Control
&
Protectio
n Unit
OUT1
Parallel
Interface
reserved
OUT7
GND
ISO1H801G
GNDCC
GNDbb
Type
On-state Resistance
Package
ISO1H801G
200mΩ
PG-DSO-36
Datasheet
3
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Pin Configuration and Functionality
1
Pin Configuration and Functionality
1.1
Pin Configuration
Pin
Symbol
1
N.C.
Not connected
2
VCC
Positive 5V logic supply
3
DIS
Output disable
4
Chip select
5
CS
WR
6
D0
Data input bit0
7
D1
Data input bit1
8
D2
Data input bit2
9
D3
Data input bit3
10
D4
Data input bit4
11
D5
Data input bit5
12
D6
Data input bit6
13
D7
Data input bit7
Function
reserved -
15
GNDCC
16
N.C.
Not connected
17
N.C.
Not connected
18
N.C.
Not connected
19
GNDbb
20
N.C
21
OUT7
High-side output of channel 7
22
OUT7
High-side output of channel 7
23
OUT6
High-side output of channel 6
24
OUT6
High-side output of channel 6
25
OUT5
High-side output of channel 5
26
OUT5
High-side output of channel 5
27
OUT4
High-side output of channel 4
28
OUT4
High-side output of channel 4
29
OUT3
High-side output of channel 3
30
OUT3
High-side output of channel 3
31
OUT2
High-side output of channel 2
32
OUT2
High-side output of channel 2
33
OUT1
High-side output of channel 1
34
OUT1
High-side output of channel 1
35
OUT0
High-side output of channel 0
36
OUT0
High-side output of channel 0
TAB
Vbb
Datasheet
N.C.
VCC
DIS
CS
WR
D0
D1
D2
D3
D4
D5
D6
D7
reserved
GNDCC
N.C.
N.C.
N.C.
Parallel write
14
Figure 1
Vbb
Input logic ground
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
TAB
TAB
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
OUT0
OUT0
OUT1
OUT1
OUT2
OUT2
OUT3
OUT3
OUT4
OUT4
OUT5
OUT5
OUT6
OUT6
OUT7
OUT7
N.C.
GNDbb
Vbb
.
Output driver ground
Not connected
Positive driver power supply voltage
Power SO-36 (430mil)
4
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Pin Configuration and Functionality
1.2
Pin Functionality
VCC (Positive 5V logic supply)
The VCC supplies the input interface that is
galvanically isolated from the output driver stage. The
input interface can be supplied with 5V.
DIS (Output disable)
The high-side outputs OUT0...OUT7 can be
immediately switched off by means of the low active pin
DIS that is an asynchronous signal. The input registers
are also reset by the DIS signal. The Output remains
switched off after low-high transition of DIS signal, till
new information is written into the input register.
Current Sink to GNDCC.
CS (Chip select)
The system microcontroller selects the ISO1H801G by
means of the low active pin CS to activate the parallel
interface. By connecting the CS pin and WR pin to
ground the parallel direct control is activated. Current
Source to VCC.
WR (Parallel write)
In parallel mode data at the input pins (D0 ... D7) are
latched by means of the rising edge of the low active
signal WR (write). Current Source to VCC.
D0 ... D7 (Data input bit0 ... bit7)
The present data can be latched on the rising edge of
the write signal WR. D0 ... D7 control the corresponding
output channels OUT0 ...OUT7. By connecting CS and
WR to ground, the signals at D0 ... D7 directly control
the outputs. Current Sink to GNDCC.
GNDCC (Ground for VCC domain)
This pin acts as the ground reference for the input
interface that is supplied by VCC.
GNDbb (Output driver ground domain)
This pin acts as the ground reference for the output
driver that is supplied by Vbb.
OUT0 ... OUT7 (High side output channel 0 ... 7)
The output high side channels are internally connected
to Vbb and controlled by the corresponding data input
pins D0 ... D7 in parallel mode.
TAB (Vbb, Positive supply for output driver)
The heatslug is connected to the positive supply port of
the output interface.
Datasheet
5
Version 2.3, 2009-09-16
Datasheet
6
reserved
D0
D1
D2
D3
D4
D5
D6
D7
WR
CS
ISO1H801G
< D0 - D7
>
Parallel
Input Interface
High-side Channel
7
Logic
Charge
Pump
Level shifter
Rectifier
Charge
Pump
Level Shifter
Rectifier
Overvoltage
Protection
Temperature Sensor
Overload Protection
Current Limitation
Limitation of Unclamped
Inductive Load
Gate
Protection
Channel 1
... 6
Temperature Sensor
Overload Protection
Current Limitation
Limitation of Unclamped
Inductive Load
Gate
Protection
Voltage
Source
from
Temperatur
e Sensor
Channel 1 6
Undervoltage
Shutdown with
Restart
Common
Diagnostic
Output
High-side Channel
0
Logic
to Logic
Channel 1 6
to Logic
Channel 1 6
Serial
to
Parallel
Vbb
OUT7
OUT6
OUT5
OUT4
OUT3
OUT2
OUT1
OUT0
GNDbb
Blockdiagram
Direct
Mode
Control
Parallel
to
Serial
CT
Figure 2
DIS
Logic
Blockdiagram
GNDCC
Undervoltage
Shutdown with
Restart
Vbb
2
Galvanic
Isolation
VCC
ISOFACE™
ISO1H801G
Blockdiagram
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Functional Description
3
Functional Description
3.1
Introduction
when solenoid loads are switched off. VON is then
clamped to 47V (min.).
The ISOFACE ISO1H801G includes 8 high-side power
switches that are controlled by means of the integrated
parallel interface. The interface is 8bit µC compatible.
Furthermore a direct control mode can be selected that
allows the direct control of the outputs OUT0...OUT7 by
means of the inputs D0...D7 without any additional logic
signal. The IC can replace 8 optocouplers and the 8
high-side switches in conventional I/O-Applications as
a galvanic isolation is implemented by means of the
integrated coreless transformer technology. The µC
compatible interfaces allow a direct connection to the
ports of a microcontroller without the need for other
components. Each of the 8 high-side power switches is
protected
against
short to
Vbb,
overload,
overtemperature and against overvoltage by an active
zener clamp.
Vbb
Vz
VON
OUTx
GNDbb
Figure 3
Inductive and overvoltage output
clamp (each channel)
Energy is stored in the load inductance during an
inductive load switch-off.
The diagnostic logic on the power chip recognizes the
overtemperature information of each power transistor.
3.2
Vbb
EL = 1 ⁄ 2 × L × IL
2
Power Supply
Ebb
The IC contains 2 galvanic isolated voltage domains
that are independent from each other. The input
interface is supplied at VCC and the output stage is
supplied at Vbb. The different voltage domains can be
switched on at different time. The output stage is only
enabled once the input stage enters a stable state.
EAS
ELoad
Vbb
Dx
OUTx
L
Vbb
GNDbb
EL
ZL
3.3
Output Stage
RL
Each channel contains a high-side vertical power FET
that is protected by embedded protection functions.
Figure 4
The continous current for each channel is 625mA (all
channels ON).
3.3.1
Output Stage Control
E AS = E bb + E L – E R = V ON ( CL ) × i L ( t )dt
with an approximate solution for RL > 0Ω:
IL × L
IL × RL 
E AS = ---------------- × ( V bb + V ON ( CL ) ) × ln  1 + -----------------------2 × RL
V ON ( CL ) 
3.3.3
Power Transistor Overcurrent
Protection
The outputs are provided with a current limitation that
enters a repetitive switched mode after an initial peak
current has been exceeded. The initial peak short
circuit current limit is set to IL(SCp). During the repetitive
mode short circuit current the limit is set to IL(SCr). If this
operation leads to an overtemperature condition, a
second protection level (Tj > 135°C) will change the
Power Transistor Overvoltage
Protection
Each of the eight output stages has it own zener clamp
that causes a voltage limitation at the power transistor
Datasheet
Inductive load switch-off energy
dissipation (each channel)
While demagnetizing the load inductance, the energy
dissipation in the DMOS is
Each output is independently controlled by an output
latch and a common reset line via the pin DIS that
disables all eight outputs and reset the latches. The
parallel input data is transferred to the input latches
with a high-to-low transition of the signal WR (write)
while the CS is logic low. A low-to-high transition of CS
transfers then the data of the input latches to the output
buffer.
3.3.2
ER
7
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Functional Description
3.4
output into a low duty cycle PWM (selective thermal
shutdown with restart) to prevent critical chip
temperatures.
Reserved
IN
VOUT
t
TJ
t
t
Figure 5
Overtemperature detection
The following figures show the timing for a turn on into
short circuit and a short circuit in on-state. Heating up
of the chip may require several milliseconds,
depending on external conditions.
IN
t
VOUT
Output short to GND
IL
IL(SCp)
t
IL(SCr)
t
Figure 6
Turn on into short circuit, shut down by
overtemperature, restart by cooling
IN
t
VOUT
Normal
operation
IL
Output short to GND
IL(SCp)
t
IL(SCr)
t
Figure 7
Datasheet
Short circuit in on-state, shut down
down by overtemperature, restart by
cooling
8
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Functional Description
Parallel Interface
3.5.2
uC Control Mode
The ISO1H801G contains a parallel interface that can
be directly controlled by the microcontroller output
ports. The parallel interface can also be switched over
to a direct control that allows direct changes of the
outputs OUT0 ... OUT7 by means of the corresponding
inputs D0 ... D7 without additional logic signals. To
activate the parallel direct control mode pin CS and pin
WR have to be connected both to GNDCC.
3.5.1
VCC
VCC
AD0
WR
CS
WR
P0
P1
P2
P3
P4
P5
P6
P7
Parallel Interface Signal
Description
CS - Chip select. The system microcontroller selects
the ISO1H801G by means of the CS pin. Whenever the
pin is in a logic low state, data can be transferred from
the µC.
GND
µC (i.e
C166)
Parallel input data can be written in from then on
CS Low to high transition:
•
The data in the input latches is transferred to the
output buffer
Figure 8
Parallel bus configuration
3.5.3
Direct Control Mode
VCC
VCC
Parallel input data at the pins D0 - D7 is written into
the input latches
VCC
CS
WR
WR Logic high level:
The parallel input data is latched in the input
latches. Any changes at the pins D0 - D7 after the
low-to-high transition of WR do not affect the input
latches.
D0 ... D7 - Parallel input. Parallel data bits are fed into
the pins D0 ... D7. The data is written into the input
latches when WR is logic low.
P0
P1
P2
P3
P4
P5
P6
P7
D0
D1
D2
D3
D4
D5
D6
D7
reserved
GND
GNDCC
Controller
Figure 9
Datasheet
IC1
.
WR Logic low level:
•
GNDCC
Beside the use of the parallel µC compatible interface a
parallel direct control mode can be choosen. In this
mode the output OUT0...OUT7 can be directly
controlled via the inputs D0...D7 without the need for
additional logic signals. To activate this mode pin CS
and WR need to be connected to GNDCC.
WR - Write. The system controller enables the write
procedure in the ISO1H801G by means of the signal
WR. A logic low state signal at pin WR writes the input
data into the input latches when the CS pin is in a logic
low state.
•
Output
lines
reserved
CS High to low transition:
•
D0
D1
D2
D3
D4
D5
D6
D7
Parallel Interface
VCC
9
Parallel Interface
3.5
Output
lines
IC1
Parallel Direct Control
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Functional Description
3.6
Parallel Interface Timing
CS
WR
tCSWR
t WHCS
t CSD
tWRPW
t DS
DATA
tDH
D0 - D7
ton/off
OUTPUT
OUT0 - OUT7
Figure 10
Parallel input - output timing diagram
3.7
Transmission Failure Detection
There is a failure detection unit integrated to ensure also a stable functionality during the integrated coreless
transformer transmission. This unit decides wether the transmitted data is valid or not. If four times serial data
coming in from the internal registers is not accepted, the output stages are switched off until the next valid data is
received.
Datasheet
10
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Electrical Characteristics
4
Electrical Characteristics
Note: All voltages at pins 2 to 14 are measured with respect to ground GNDCC (pin 15). All voltages at pin 20 to
pin 36 and TAB are measured with respect to ground GNDbb (pin 19). The voltage levels are valid if other
ratings are not violated. The two voltage domains VCC and Vbb are internally galvanic isolated.
4.1
Absolute Maximum Ratings
Note: Absolute maximum ratings are defined as ratings, which when being exceeded may lead to destruction of
the integrated circuit. For the same reason make sure, that any capacitor that will be connected to pin 2
(VCC) and TAB (Vbb) is discharged before assembling the application circuit. Supply voltages higher than
Vbb(AZ) require an external current limit for the GNDbb pin, e.g. with a 15Ω resistor in GNDbb connection.
Operating at absolute maximum ratings can lead to a reduced lifetime.
Parameter
at Tj = -40 ... 135°C, unless otherwise specified
Symbol
Supply voltage input interface (VCC)
VCC
Limit Values
Unit
min.
max.
-0.5
6.5
1)
45
Supply voltage output interface (Vbb)
Vbb
-1
Continuous voltage at data inputs (D0 ... D7)
VDx
-0.5
6.5
Continuous voltage at pin CS
VCS
-0.5
6.5
Continuous voltage at pin WR
VWR
-0.5
6.5
Continuous voltage at pin DIS
VDIS
-0.5
6.5
Continuous voltage at reserved pin
VReserved
-0.5
6.5
Load current (short-circuit current)
IL

self limited
Reverse current through GNDbb1)
IGNDbb
-1.6

Operating Temperature
Tj
-25
Storage Temperature
Tstg
-50
150

3.3
Power Dissipation
2)
Ptot
3)
Inductive load switch-off energy dissipation single
pulse, Tj = 125°C, IL = 0.625A
one channel active
all channel simultaneously active (each channel)
Load dump protection3) VloadDump4)=VA + VS
VIN = low or high
td = 400ms, RI = 2Ω, RL = 27Ω, VA = 13.5V
td = 350ms, RI = 2Ω, RL = 57Ω, VA = 27V
V
A
internal limited °C
EAS
W
J

10
1
VLoaddump
V
90
117
Electrostatic discharge voltage (Human Body Model)
according to JESD22-A114-B
VESD
Electrostatic discharge voltage (Charge Device Model)
according to ESD STM5.3.1 - 1999
VESD
Continuous reverse drain current1)3), each channel
IS
kV
2
kV
1

4
A
1) defined by Ptot
2) Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm² (one layer, 70µm thick) copper area for drain connection. PCB
is vertical without blown air.
3) not subject to production test, specified by design
4) VLoaddump is setup without the DUT connected to the generator per ISO7637-1 and DIN40839
Datasheet
11
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Electrical Characteristics
4.2
Thermal Characteristics
Parameter
at Tj = -25 ... 125°C, Vbb=15...30V, VCC=4.5...5.5V, unless
otherwise specified
Symbol
Thermal resistance junction - case
RthJC
Thermal resistance @ min. footprint
Rth(JA)
Thermal resistance @ 6cm² cooling area1)
Rth(JA)
Limit Values
Unit Test Condition
min.
typ.
max.






1.5
K/W
50
38
1) Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm² (one layer, 70µm thick) copper area for drain connection. PCB
is vertical without blown air.
4.3
Load Switching Capabilities and Characteristics
Parameter
at Tj = -25 ... 125°C, Vbb=15...30V, VCC=4.5...5.5V, unless
otherwise specified
On-state resistance, IL = 0.5A
Tj = 25°C
Tj = 125°C
Symbol
RON
Limit Values
Unit
min.
typ.
max.
150
270
200
320
64
120
Test Condition
mΩ
Turn-on time to 90% VOUT1)
RL = 47Ω, VDx = 0 to 5V
ton



Turn-off time to 10% VOUT1)
RL = 47Ω, VDx = 5 to 0V
toff

89
170
Slew rate on 10 to 30% VOUT
RL = 47Ω, Vbb = 15V
dV/dton

1
2
Slew rate off 70 to 40% VOUT
RL = 47Ω, Vbb = 15V
-dV/dtoff

1
2
µs
V/µs
1) The turn-on and turn-off time includes the switching time of the high-side switch and the transmission time via the coreless
transformer in normal operating mode. During a failure on the coreless transformer transmission turn-on or turn-off time
can increase by up to 50µs.
4.4
Operating Parameters
Parameter
at Tj = -25 ... 125°C, Vbb=15...30V, VCC=4.5...5.5V, unless
otherwise specified
Symbol
Common mode transient immunity1)
Magnetic field immunity
Voltage domain Vbb
(Output interface)
Datasheet
1)
Limit Values
Unit
min.
typ.
max.
∆VISO/dt
-25
-
25
HIM
100
Test Condition
kV/µs ∆VISO = 200V
A/m
IEC61000-4-8
Undervoltage shutdown
Vbb(under)
7

10.5
Undervoltage restart
Vbb(u_rst)

11
Undervoltage hysteresis
∆Vbb(under)
0.5

Undervoltage current
Ibb(uvlo)
1
2.5
mA
Vbb < 7V
Operating current
IGNDL




10
14
mA
All Channels
ON - no load
Leakage output current
(included in Ibb(off))
VDx = low, each channel
IL(off)

5
30
µA
12
V
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Electrical Characteristics
Voltage domain VCC Operating voltage
(Input interface)
Undervoltage shutdown
VCC
4.5
VCC(under)
2.5
Undervoltage restart
VCC(u_rst)
Undervoltage hysteresis
∆VCC(under)
Undervoltage current
ICC(uvlo)
Operating current
ICC(on)







5.5
0.1

1
2
mA
4.5
6
mA
V
2.9
3
Vcc < 2.5V
1) not subject to production test
4.5
Output Protection Functions
Parameter1)
at Tj = -25 ... 125°C, Vbb=15...30V, VCC=4.5...5.5V, unless
otherwise specified
Symbol
Initial peak short circuit current limit,
Vbb = 30V, tm = 700µs
Tj = -25°C
Tj = 25°C
Tj = 125°C
IL(SCp)
Repetitive short circuit current limit3)
Tj = Tjt (see timing diagrams)
Limit Values
min.
typ.
Unit Test Condition
max.
A



1.9
0.7

IL(SCr)

1.1



Output clamp (inductive load switch off)
at VOUT = Vbb - VON(CL)
VON(CL)
47
53
60
V
Overvoltage protection
Vbb(AZ)
47
Tjt
135


°C

10



2)3)
Thermal overload trip temperature
3)
Thermal hysteresis
∆Tjt
1.4
K
1) Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet.
Fault conditions are considered as “outside” normal operating range. Protection functions are not designed for continous
repetitive operation.
2) Higher operating temperature at normal function for each channel available
3) not subject to production test, specified by design
4.6
Datasheet
Reserved
13
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Electrical Characteristics
4.7
Input Interface
Parameter
at Tj = -25 ... 125°C, Vbb=15...30V, VCC=4.5...5.5V, unless
otherwise specified
Symbol
Limit Values
Unit Test Condition
min.
typ.
max.
0.3 x
VCC
Input low state voltage
(D0 ... D7, DIS, CS, WR)
VIL
-0.3

Input high state voltage
(D0 ... D7, DIS, CS, WR)
VIH
0.7 x
VCC

Input voltage hysteresis
(D0 ... D7, DIS, CS, WR)
VIHys
100
mV
Input pull down current
(D0 ... D7, DIS)
IIdown
100
µA
Input pull up current
(CS, WR)
-IIup
100
Output disable time (transition DIS to logic low)1)2)
Normal operation
Turn-off time to 10% VOUT
RL = 47Ω
tDIS
---
85
170
Output disable time (transition DIS to logic low)1)2)3)
Disturbed operation
Turn-off time to 10% VOUT
RL = 47Ω
tDIS
---
---
230
V
VCC+
0.3
µs
1) The time includes the turn-on/off time of the high-side switch and the transmission time via the coreless transformer.
2) If Pin DIS is set to low the outputs are set to low; after DIS set to high a new write cycle is necessary to set the output again.
3) The parameter is not subject to production test - verified by design/characterization
4.8
Parallel Interface Input Timing
Parameter
at Tj = -25 ... 125°C, Vbb=15...30V, VCC=4.5...5.5V, unless
otherwise specified
Symbol
Limit Values
Unit Test Condition
min.
typ.
max.
tWRPW
20
Data setup time before WR
tDS
20
Data hold time after WR
tDH
10
Chip select valid to WR
tCSWR
0
WR logic high to CS logic high
tWHCS
10
tCSD
10












WR pulse width
Delay to next CS cycle
Datasheet
14
ns
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Electrical Characteristics
4.9
Reverse Voltage
Parameter
at Tj = -25 ... 125°C, Vbb=15...30V, VCC=4.5...5.5V, unless
otherwise specified
Symbol
Reverse voltage1)2)
RGND = 0 Ω
RGND = 150 Ω
-Vbb
Diode forward on voltage
IF = 1.25A, VDx = low, each channel
-VON
Limit Values
Unit Test Condition
min.
typ.
max.




1
45


1.2
V
1) defined by Ptot
2) not subject to production test, specified by design
4.10
Isolation and Safety-Related Specification
Parameter
Measured from input terminals to output terminals,
unless otherwise specified
Value
Unit
Conditions
Rated dielectric isolation voltage VISO
500
VAC
1 minute duration 1)
Minimum external air gap (clearance)
2.6
mm
shortest distance through air.
Minimum external tracking (creepage)
2.6
mm
shortest distance path along body.
Minimum Internal Gap
0.01
mm
Insulation distance through
insulation
1) The parameter is not subject to production test, verified by characterization; Production Test with 1100V, 100ms duration
Note: For Qualification Report contact your local Infineon Technologies office!
Datasheet
15
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Electrical Characteristics
Datasheet
16
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Electrical Characteristics
Datasheet
17
Version 2.3, 2009-09-16
ISOFACE™
ISO1H801G
Package Outlines
Package Outlines
0.65
0.25 +0.13
15.74 ±0.1
(Heatslug)
6.3
(Mold)
5˚ ±3˚
0.02
2.8
0.1 C
B
0.25 +0.07
-
0 +0.1
1.1 ±0.1
11 ±0.15 1)
1.3
(Plastic Dual Small
Outline Package)
3.25 ±0.1
PG-DSO-36
3.5 MAX.
5
Heatslug
0.95 ±0.15
36x
0.25 M A B C
14.2 ±0.3
0.25 B
19
19
1
18
10
36
5.9 ±0.1
(Metal)
36
3.2 ±0.1
(Metal)
Bottom View
Index Marking
1 x 45˚
15.9 ±0.1 1)
(Mold)
1)
Figure 11
Datasheet
A
13.7 -0.2
(Metal)
Does not include plastic or metal protrusion of 0.15 max. per side
1
Heatslug
gps09181_1
PG-DSO-36
18
Version 2.3, 2009-09-16
Total Quality Management
Qualität hat für uns eine umfassende
Bedeutung. Wir wollen allen Ihren
Ansprüchen in der bestmöglichen
Weise gerecht werden. Es geht uns
also nicht nur um die Produktqualität –
unsere
Anstrengungen
gelten
gleichermaßen der Lieferqualität und
Logistik, dem Service und Support
sowie allen sonstigen Beratungs- und
Betreuungsleistungen.
Dazu
gehört
eine
bestimmte
Geisteshaltung unserer Mitarbeiter.
Total Quality im Denken und Handeln
gegenüber Kollegen, Lieferanten und
Ihnen, unserem Kunden. Unsere
Leitlinie ist jede Aufgabe mit „Null
Fehlern“ zu lösen – in offener
Sichtweise auch über den eigenen
Arbeitsplatz hinaus – und uns ständig
zu verbessern.
Unternehmensweit orientieren wir uns
dabei auch an „top“ (Time Optimized
Processes), um Ihnen durch größere
Schnelligkeit den entscheidenden
Wettbewerbsvorsprung zu verschaffen.
Geben Sie uns die Chance, hohe
Leistung durch umfassende Qualität zu
beweisen.
Wir werden Sie überzeugen.
www.infineon.com
Published by Infineon Technologies AG
Quality takes on an allencompassing
significance at Semiconductor Group.
For us it means living up to each and
every one of your demands in the best
possible way. So we are not only
concerned with product quality. We
direct our efforts equally at quality of
supply and logistics, service and
support, as well as all the other ways in
which we advise and attend to you.
Part of this is the very special attitude of
our staff. Total Quality in thought and
deed, towards co-workers, suppliers
and you, our customer. Our guideline is
“do everything with zero defects”, in an
open manner that is demonstrated
beyond your immediate workplace, and
to constantly improve.
Throughout the corporation we also
think in terms of Time Optimized
Processes (top), greater speed on our
part to give you that decisive
competitive edge.
Give us the chance to prove the best of
performance through the best of quality
– you will be convinced.