ACS716 Datasheet

ACS716
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
Features and Benefits
▪Industry-leading noise performance with greatly improved
bandwidth through proprietary amplifier and filter design
techniques
▪Small footprint package suitable for space-constrained
applications
▪1 mΩ primary conductor resistance for low power loss
▪High isolation voltage, suitable for line-powered
applications
▪User-adjustable Overcurrent Fault level
▪Overcurrent Fault signal typically responds to an
overcurrent condition in < 2 μs
▪Integrated shield virtually eliminates capacitive coupling
from current conductor to die due to high dV/dt voltage
transients
▪Filter pin capacitor improves resolution in low bandwidth
applications
▪3 to 3.6 V single supply operation
▪Factory-trimmed sensitivity and quiescent output voltage
▪Chopper stabilization results in extremely stable quiescent
output voltage
▪Ratiometric output from supply voltage
CB Certificate Number:
US-23711-UL
Package: 16-Pin SOIC Hall Effect IC
Package (suffix LA)
Description
The Allegro™ ACS716 current sensor provides economical
and precise means for current sensing applications in industrial,
commercial, and communications systems. The device is offered
in a small footprint surface-mount package that allows easy
implementation in customer applications.
The ACS716 consists of a precision linear Hall sensor integrated
circuit with a copper conduction path located near the surface
of the silicon die. Applied current flows through the copper
conduction path, and the analog output voltage from the Hall
sensor linearly tracks the magnetic field generated by the
applied current. The accuracy of the ACS716 is maximized
with this patented packaging configuration because the Hall
element is situated in extremely close proximity to the current
to be measured.
High-level immunity to current conductor dV/dt and stray
electric fields, offered by Allegro proprietary integrated shield
technology, results in low ripple on the output and low offset
drift in high-side, high-voltage applications.
The voltage on the Overcurrent Input (VOC pin) allows
customers to define an overcurrent fault threshold for the device.
When the current flowing through the copper conduction path
(between the IP+ and IP– pins) exceeds this threshold, the open
drain Overcurrent Fault pin will transition to a logic low state.
Factory programming of the linear Hall sensor inside of the
ACS716 results in exceptional accuracy in both analog and
digital output signals.
The internal resistance of the copper path used for current
sensing is typically 1 mΩ, for low power loss. Also, the current
conduction path is electrically isolated from the low-voltage
Not to scale
1
2
3
IP
4
5
6
7
8
IP+
IP+
IP+
FAULT_EN
ACS716
VOC
VCC
IP+
FAULT
IP–
VIOUT
IP–
FILTER
IP–
VZCR
IP–
GND
ACS716-DS, Rev. 4
16 Fault_EN
Continued on the next page…
RH
VCC
15
RH, RL
14
CF
RL
RPU
13
12
11
COC
VIOUT
10
9
1 nF
A
COC
0.1 µF
B
CF
Sets resistor divider reference for VOC
Noise and bandwidth limiting filter capacitor
Fault delay setting capacitor, 22 nF maximum
A
Use of capacitor required
B
Use of resistor optional, 330 kΩ recommended.
If used, resistor must be connected between
F̄¯ Ā Ū¯L̄¯ T̄¯ pin and VCC.
ACS716
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
Description (continued)
sensor inputs and outputs. This allows the ACS716 family of sensors
to be used in applications requiring electrical isolation, without the
use of opto-isolators or other costly isolation techniques.
Pb‑based solder balls, currently exempt from RoHS. The device is
fully calibrated prior to shipment from the factory.
The ACS716 is provided in a small, surface-mount SOIC16 package.
The leadframe is plated with 100% matte tin, which is compatible
with standard lead (Pb) free printed circuit board assembly processes.
Internally, the device is Pb-free, except for flip-chip high-temperature
Applications include:
• Motor control and protection
• Load management and overcurrent detection
• Power conversion and battery monitoring / UPS systems
Selection Guide
Part Number
ACS716KLATR-6BB-T2
IP
(A)
Sens (typ)
at VCC = 3.3 V
(mV/A)
Latched
Fault
±6
100
Yes
ACS716KLATR-12CB-T2
±12.5
37
Yes
ACS716KLATR-25CB-T2
±25
18.5
Yes
ACS716KLATR-6BB-NL-T2
±6
100
No
ACS716KLATR-12CB-NL-T2
±12.5
37
No
ACS716KLATR-25CB-NL-T2
±25
18.5
No
TA
(°C)
–40 to 125
Packing1
Tape and Reel, 1000 pieces per reel
1 Contact Allegro
2 Variant
for packing options.
not intended for automotive applications.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
2
ACS716
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
Absolute Maximum Ratings
Characteristic
Symbol
Supply Voltage
Notes
Rating
Units
8
V
VCC
Filter Pin
VFILTER
8
V
Analog Output Pin
VIOUT
32
V
Overcurrent Input Pin
VOC
8
V
V F̄¯ Ā Ū¯L̄¯ T̄¯ 8
V
Fault Enable (FAULT_EN) Pin
VFAULTEN
8
V
Voltage Reference Output Pin
VZCR
8
V
DC Reverse Voltage: VCC, FILTER, VIOUT, VOC,
¯ Ā ¯ T̄
¯, FAULT_EN, and VZCR Pins
F̄
Ū¯L̄
VRdcx
–0.5
V
Excess to Supply Voltage: FILTER, VIOUT, VOC,
¯ Ā ¯ T̄
¯, FAULT_EN, and VZCR Pins
F̄
Ū¯L̄
VEX
0.3
V
3
mA
¯ Ā ¯ T̄
¯ Pin
Overcurrent F̄
Ū¯L̄
Output Current Source
Voltage by which pin voltage can exceed the VCC pin
voltage
IIOUT(Source)
Output Current Sink
IIOUT(Sink)
Operating Ambient Temperature
TA
Range K
1
mA
–40 to 125
°C
Junction Temperature
TJ(max)
165
°C
Storage Temperature
Tstg
–65 to 170
°C
Isolation Characteristics
Characteristic
Dielectric Strength Test Voltage*
Working Voltage for Basic Isolation
Symbol
VISO
VWVBI
Notes
Rating
Unit
Agency type-tested for 60 seconds per IEC/UL 60950-1 (2nd Edition).
3600
VRMS
Agency type-tested for 60 seconds per UL 1577.
3000
VRMS
Maximum approved working voltage for basic (single) isolation
according to IEC/UL 60950-1 (2nd Edition).
870
VPK or VDC
616
VRMS
Clearance
DCL
Minimum distance through air from IP leads to signal leads.
7.5
mm
Creepage
DCR
Minimum distance along package body from IP leads to signal leads.
7.5
mm
*Production tested for 1 second at 3600 VRMS in accordance with both UL 1577 and IEC/UL 60950-1 (edition 2).
Thermal Characteristics
Characteristic
Package Thermal Resistance
Symbol
RθJA
Test Conditions
Value Units
When mounted on Allegro demo board with 1332 mm2 (654 mm2 on component side and 678 mm2 on opposite side) of 2 oz. copper connected to
the primary leadframe and with thermal vias connecting the copper layers.
Performance is based on current flowing through the primary leadframe and
includes the power consumed by the PCB.
17
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
ºC/W
3
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
Functional Block Diagram
Latching Versions
VCC
Hall
Bias
FAULT_EN
D
Q
CLK
R
POR
POR
Fault Latch
FAULT Reset
Drain
–
VOC
+
2VREF
OC Fault
Control
Logic
FAULT
3 mA
Fault
Comparator
–
Sensitivity
Trim
IP+
VZCR
+
VIOUT
Signal
Recovery
RF(INT)
Hall
Amplifier
IP–
VOUT(Q)
Trim
GND
FILTER
Terminal List Table, Latching Versions
Number
Pin-Out Diagram
IP+ 1
16 FAULT_EN
IP+ 2
15 VOC
IP+ 3
14 VCC
IP+ 4
13 FAULT
IP– 5
12 VIOUT
IP– 6
11 FILTER
IP– 7
10 VZCR
IP– 8
9 GND
Name
Description
1,2,3,4
IP+
Sensed current copper conduction path pins. Terminals for current being sensed;
fused internally, loop to IP– pins; unidirectional or bidirectional current flow.
5,6,7,8
IP–
Sensed current copper conduction path pins. Terminals for current being sensed;
fused internally, loop to IP+ pins; unidirectional or bidirectional current flow.
9
GND
Device ground connection.
10
VZCR
Voltage Reference Output pin. Zero current (0 A) reference; output voltage on this
pin scales with VCC . (Not a highly accurate reference.)
11
FILTER
Filter pin. Terminal for an external capacitor connected from this pin to GND to set
the device bandwidth.
12
VIOUT
Analog Output pin. Output voltage on this pin is proportional to current flowing
through the loop between the IP+ pins and IP– pins.
13
¯ Ā ¯ T̄¯ F̄
Ū¯L̄
Overcurrent Fault pin. When current flowing between IP+ pins and IP– pins
exceeds the overcurrent fault threshold, this pin transitions to a logic low state.
14
VCC
Supply voltage.
15
VOC
Overcurrent Input pin. Analog input voltage on this pin sets the overcurrent fault
threshold.
16
FAULT_EN Enables overcurrent faulting when high. Resets F̄¯ Ā Ū¯L̄¯ T̄¯ when low.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
4
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
Functional Block Diagram
Non-Latching Versions
VCC
Hall
Bias
POR
Drain
–
VOC
+
FAULT_EN
FAULT
2VREF
FAULT Reset
3 mA
OC Fault
IP+
VZCR
Fault
Comparator
Sensitivity
Trim
VIOUT
Signal
Recovery
RF(INT)
Hall
Amplifier
IP–
VOUT(Q)
Trim
GND
FILTER
Terminal List Table, Non-Latching Version
Pin-Out Diagram
IP+ 1
16 FAULT_EN
IP+ 2
15 VOC
IP+ 3
14 VCC
IP+ 4
13 FAULT
IP– 5
12 VIOUT
IP– 6
11 FILTER
IP– 7
10 VZCR
IP– 8
9 GND
Number
Name
Description
1,2,3,4
IP+
Sensed current copper conduction path pins. Terminals for current being sensed;
fused internally, loop to IP– pins; unidirectional or bidirectional current flow.
5,6,7,8
IP–
Sensed current copper conduction path pins. Terminals for current being sensed;
fused internally, loop to IP+ pins; unidirectional or bidirectional current flow.
9
GND
Device ground connection.
10
VZCR
Voltage Reference Output pin. Zero current (0 A) reference; output voltage on this
pin scales with VCC . (Not a highly accurate reference.)
11
FILTER
Filter pin. Terminal for an external capacitor connected from this pin to GND to set
the device bandwidth.
12
VIOUT
Analog Output pin. Output voltage on this pin is proportional to current flowing
through the loop between the IP+ pins and IP– pins.
13
¯ Ā ¯ T̄¯ F̄
Ū¯L̄
Overcurrent Fault pin. When current flowing between IP+ pins and IP– pins
exceeds the overcurrent fault threshold, this pin transitions to a logic low state.
14
VCC
Supply voltage.
15
VOC
Overcurrent Input pin. Analog input voltage on this pin sets the overcurrent fault
threshold.
16
FAULT_EN Enables overcurrent faulting when high.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
5
ACS716
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
COMMON OPERATING CHARACTERISTICS: Valid at TA = –40°C to 125°C, VCC = 3.3 V, unless otherwise specified
Characteristic
ELECTRICAL CHARACTERISTICS
Supply Voltage
Nominal Supply Voltage
Supply Current
Output Capacitance Load
Output Resistive Load
Magnetic Coupling from Device Conductor
to Hall Element
Internal Filter Resistance1
Symbol
Test Conditions
Min.
Typ.
Max.
Units
3
–
–
3.3
3.6
–
V
V
VIOUT open, F̄¯ Ā Ū¯L̄¯ T̄¯ pin high
VIOUT pin to GND
VIOUT pin to GND
–
–
10
9
–
–
11
10
–
mA
nF
kΩ
Current flowing from IP+ to IP– pins
–
9.5
–
G/A
VCC
VCCN
ICC
CLOAD
RLOAD
MCHALL
–
1.7
–
kΩ
Primary Conductor Resistance
RPRIMARY
ANALOG OUTPUT SIGNAL CHARACTERISTICS
Full Range Linearity2
ELIN
Symmetry3
ESYM
TA = 25°C
–
1
–
mΩ
IP = ±IP0A
IP = ±IP0A
–0.75
99.1
±0.25
100
0.75
100.9
%
%
Bidirectional Quiescent Output
VOUT(QBI)
TIMING PERFORMANCE CHARACTERISTICS
IP = 0 A, TA = 25°C
–
VCC×0.5
–
V
–
3
–
μs
–
1
–
μs
–
4
–
μs
–
120
–
kHz
–
35
–
μs
VOC
VCC × 0.25
–
VCC × 0.4
V
INCOMP
–
±1
–
A
Switchpoint in VOC safe operating area;
assumes INCOMP = 0 A
–
±5
–
%
1 mA sink current at F̄¯ Ā Ū¯L̄¯ T̄¯ pin
–
–
0.4
V
–
–
0.1 × VCC
V
VIOUT Signal Rise Time
VIOUT Signal Propagation Time
RF(INT)
tr
tPROP
VIOUT Signal Response Time
tRESPONSE
VIOUT Large Signal Bandwidth
f3dB
Power-On Time
tPO
OVERCURRENT CHARACTERISTICS
Setting Voltage for Overcurrent Switchpoint4
Signal Noise at Overcurrent
Comparator Input
Overcurrent Fault Switchpoint Error5,6
EOC
Overcurrent F̄¯ Ā Ū¯L̄¯ T̄¯ Pin Output Voltage
V F̄¯ Ā Ū¯L̄¯ T̄¯ Fault Enable (FAULT_EN Pin) Input Low
Voltage Threshold
VIL
TA = 25°C, Swing IP from 0 A to IP0A,
no capacitor on FILTER pin, 100 pF from
VIOUT to GND
TA = 25°C, no capacitor on FILTER pin,
100 pF from VIOUT to GND
TA = 25°C, Swing IP from 0 A to IP0A,
no capacitor on FILTER pin, 100 pF from
VIOUT to GND
–3 dB, Apply IP such that VIOUT = 1 Vpk-pk,
no capacitor on FILTER pin, 100 pF from
VIOUT to GND
Output reaches 90% of steady-state level,
no capacitor on FILTER pin, TA = 25°C
Continued on the next page…
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
6
ACS716
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
COMMON OPERATING CHARACTERISTICS (continued): Valid at TA = –40°C to 125°C, VCC = 3.3 V, unless otherwise specified
Characteristic
Symbol
OVERCURRENT CHARACTERISTICS (continued)
Test Conditions
Min.
Typ.
Max.
Units
Fault Enable (FAULT_EN Pin) Input High
Voltage Threshold
VIH
0.8 × VCC
–
–
V
Fault Enable (FAULT_EN Pin) Input
Resistance
RFEI
–
1
–
MΩ
–
15
–
µs
–
150
–
ns
–
2
–
µs
–
3
–
µs
–
500
–
ns
–
250
–
ns
2
–
–
MΩ
0.48 x VCC
0.5 × VCC
0.52 x VCC
V
3
50
–
–
–
±10
–
–
–
mA
µA
mV
Fault Enable (FAULT_EN Pin) Delay7
tFED
Fault Enable (FAULT_EN Pin) Delay
(Non-Latching versions)8
tFED(NL)
Overcurrent Fault Response Time
tOC
Undercurrent Fault Response Time
(Non-Latching versions)
tUC
Overcurrent Fault Reset Delay
tOCR
Overcurrent Fault Reset Hold Time
tOCH
Overcurrent Input Pin Resistance
VOLTAGE REFERENCE CHARACTERISTICS
ROC
Voltage Reference Output
VZCR
Voltage Reference Output Load Current
IZCR
Voltage Reference Output Drift
∆VZCR
Set FAULT_EN to low, VOC = 0.25 × VCC ,
COC = 0 F; then run a DC IP exceeding the
corresponding overcurrent threshold; then
reset FAULT_EN from low to high and
measure the delay from the rising edge of
FAULT_EN to the falling edge of F̄¯ Ā Ū¯L̄¯ T̄¯ Set FAULT_EN to low, VOC = 0.25 × VCC ,
COC = 0 F; then run a DC IP exceeding the
corresponding overcurrent threshold; then
reset FAULT_EN from low to high and
measure the delay from the rising edge of
FAULT_EN to the falling edge of F̄¯ Ā Ū¯L̄¯ T̄¯ FAULT_EN set to high for a minimum
of 20 µs before the overcurrent event;
switchpoint set at VOC = 0.25 × VCC ;
apply a current step to IP with amplitude
equal to 1.5 x VOC/ Sens;
delay from IP exceeding overcurrent
fault threshold to V F̄¯ Ā Ū¯L̄¯ T̄¯ < 0.4 V, without
external COC capacitor
FAULT_EN set to high for a minimum
of 20 μs before the undercurrent event;
switchpoint set at VOC = 0.25 × VCC ; delay
from IP falling below the overcurrent fault
threshold to V F̄¯ Ā Ū¯L̄¯ T̄¯ > 0.8 × VCC, without
external COC capacitor, RPU = 330 kΩ
Time from VFAULTEN < VIL to
VFAULT > 0.8 × VCC , RPU = 330 kΩ
Time from VFAULTEN pin < VIL to reset of
fault latch; see Functional Block Diagram
TA = 25°C, VOC pin to GND
TA = 25 °C
(Not a highly accurate reference)
Source current
Sink current
1R
F(INT) forms an RC circuit via the FILTER pin.
2 This parameter can drift by as much as 0.8% over
the lifetime of this product.
parameter can drift by as much as 1% over the lifetime of this product.
4 See page 8 on how to set overcurrent fault switchpoint.
5 Switchpoint can be lower at the expense of switchpoint accuracy.
6 This error specification does not include the effect of noise. See the I
NCOMP specification in order to factor in the additional influence of noise on the
fault switchpoint.
7 Fault Enable Delay is designed to avoid false tripping of an Overcurrent (OC) fault at power-up. A 15 µs (typical) delay will always be needed, every
time FAULT_EN is raised from low to high, before the device is ready for responding to any overcurrent event.
8 During power-up, this delay is 15 µs in order to avoid false tripping of an Overcurrent (OC) fault.
3 This
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
7
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
PERFORMANCE CHARACTERISTICS: TA Range K, valid at TA = – 40°C to 125°C, VCC = 3.3 V, unless otherwise specified
Characteristic
Symbol
Test Conditions
Min.
Typ.
Max.
Units
IPOA
–7.5
–
7.5
A
IR
–14
–
14
A
–
3.0
–
mV
X6BB CHARACTERISTICS
Optimized Accuracy Range1
Linear Sensing Range
Noise2
VNOISE(rms) TA = 25°C, Sens = 100 mV/A, Cf = 0, CLOAD = 4.7 nF, RLOAD open
Sensitivity3
Sens
Electrical Offset Voltage
Variation Relative to
VOUT(QBI)4
VOE
Total Output Error5
ETOT
IP = 6.5 A, TA = 25°C
–
100
–
mV/A
IP = 6.5 A, TA = 25°C to 125°C
–
100
–
mV/A
IP = 6.5 A, TA = – 40°C to 25°C
–
101
–
mV/A
IP = 0 A, TA = 25°C
–
±11
–
mV
IP = 0 A, TA = 25°C to 125°C
–
±11
–
mV
IP = 0 A, TA = – 40°C to 25°C
–
±35
–
mV
Over full scale of IPOA , IP applied for 5 ms, TA = 25°C to 125°C
–
±2.2
–
%
Over full scale of IPOA , IP applied for 5 ms, TA = – 40°C to 25°C
–
±6
–
%
1 Although the device is accurate over the entire linear range, the device is programmed for maximum accuracy over the range defined by I
POA .
The reason for this is that in many applications, such as motor control, the start-up current of the motor is approximately three times higher than the
running current.
2V
pk-pk noise (6 sigma noise) is equal to 6 × VNOISE(rms). Lower noise levels than this can be achieved by using Cf for applications requiring narrower
bandwidth. See Characteristic Performance page for graphs of noise versus Cf and bandwidth versus Cf.
3 This parameter can drift by as much as 2.4% over the lifetime of this product.
4 This parameter can drift by as much as 13 mV over the lifetime of this product.
5 This parameter can drift by as much as 2.5% over the lifetime of this product.
PERFORMANCE CHARACTERISTICS: TA Range K, valid at TA = – 40°C to 125°C, VCC = 3.3 V, unless otherwise specified
Characteristic
Symbol
Test Conditions
Min.
Typ.
Max.
Units
IPOA
–12.5
–
12.5
A
IR
–37.5
–
37.5
A
X12CB CHARACTERISTICS
Optimized Accuracy Range1
Linear Sensing Range
Noise2
Sensitivity3
VNOISE(rms) TA = 25°C, Sens = 37 mV/A, Cf = 0, CLOAD = 4.7 nF, RLOAD open
Sens
Electrical Offset Voltage
Variation Relative to
VOUT(QBI)4
VOE
Total Output Error5
ETOT
–
1.0
–
mV
IP = 12.5 A, TA = 25°C
–
37.1
–
mV/A
IP = 12.5 A, TA = 25°C to 125°C
–
37.0
–
mV/A
IP = 12.5 A, TA = – 40°C to 25°C
–
37.7
–
mV/A
IP = 0 A, TA = 25°C
–
±6
–
mV
IP = 0 A, TA = 25°C to 125°C
–
±11
–
mV
IP = 0 A, TA = – 40°C to 25°C
–
±21
–
mV
Over full scale of IPOA , IP applied for 5 ms, TA = 25°C to 125°C
–
±2.7
–
%
Over full scale of IPOA , IP applied for 5 ms, TA = – 40°C to 25°C
–
±6.5
–
%
1 Although the device is accurate over the entire linear range, the device is programmed for maximum accuracy over the range defined by I
POA .
The reason for this is that in many applications, such as motor control, the start-up current of the motor is approximately three times higher than the
running current.
2V
pk-pk noise (6 sigma noise) is equal to 6 × VNOISE(rms). Lower noise levels than this can be achieved by using Cf for applications requiring narrower
bandwidth. See Characteristic Performance page for graphs of noise versus Cf and bandwidth versus Cf.
3 This parameter can drift by as much as 2.4% over the lifetime of this product.
4 This parameter can drift by as much as 13 mV over the lifetime of this product.
5 This parameter can drift by as much as 2.5% over the lifetime of this product.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
8
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
PERFORMANCE CHARACTERISTICS: TA Range K, valid at TA = – 40°C to 125°C, VCC = 3.3 V, unless otherwise specified
Characteristic
Symbol
Test Conditions
Min.
Typ.
Max.
Units
IPOA
–25
–
25
A
IR
–75
–
75
A
–
0.5
–
mV
X25CB CHARACTERISTICS
Optimized Accuracy Range1
Linear Sensing Range
Noise2
Sensitivity3
VNOISE(rms) TA = 25°C, Sens = 18.5 mV/A, Cf = 0, CLOAD = 4.7 nF, RLOAD open
Sens
Electrical Offset Voltage
Variation Relative to
VOUT(QBI)4
VOE
Total Output Error5
ETOT
IP = 25 A, TA = 25°C
–
18.6
–
mV/A
IP = 25 A, TA = 25°C to 125°C
–
18.5
–
mV/A
IP = 25 A, TA = – 40°C to 25°C
–
18.9
–
mV/A
IP = 0 A, TA = 25°C
–
±5
–
mV
IP = 0 A, TA = 25°C to 125°C
–
±13
–
mV
IP = 0 A, TA = – 40°C to 25°C
–
±18
–
mV
Over full scale of IPOA , IP applied for 5 ms, TA = 25°C to 125°C
–
±2.9
–
%
Over full scale of IPOA , IP applied for 5 ms, TA = – 40°C to 25°C
–
±5.2
–
%
1 Although the device is accurate over the entire linear range, the device is programmed for maximum accuracy over the range defined by I
POA .
The reason for this is that in many applications, such as motor control, the start-up current of the motor is approximately three times higher than the
running current.
2V
pk-pk noise (6 sigma noise) is equal to 6 × VNOISE(rms). Lower noise levels than this can be achieved by using Cf for applications requiring narrower
bandwidth. See Characteristic Performance page for graphs of noise versus Cf and bandwidth versus Cf.
3 This parameter can drift by as much as 2.4% over the lifetime of this product.
4 This parameter can drift by as much as 13 mV over the lifetime of this product.
5 This parameter can drift by as much as 2.5% over the lifetime of this product.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
9
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
Characteristic Performance
ACS716 Bandwidth versus External Capacitor Value, CF
1000
Capacitor connected between FILTER pin and GND
Bandwidth (kHz)
100
10
1
0.1
0.01
0.1
1
10
100
1000
Capacitance (nF)
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
10
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
Characteristic Performance Data
Data taken using the ACS716-6BB
Accuracy Data
Electrical Offset Voltage versus Ambient Temperature
Sensitivity versus Ambient Temperature
50
110.0
40
107.5
30
Sens (mV/A)
VOE (mV)
20
10
0
-10
-20
102.5
100.0
97.5
95.0
-30
92.5
-40
-50
–50
105.0
-25
0
25
50
75
100
125
90.0
150
–50
-25
0
25
TA (°C)
100.75
0.2
100.50
0.1
100.25
ESYM (%)
0.3
0
-0.1
99.50
99.25
50
150
99.75
-0.3
25
125
100.00
-0.2
0
100
Symmetry versus Ambient Temperature
101.00
75
100
125
99.00
–50
150
-25
0
25
50
75
100
125
150
TA (°C)
TA (°C)
Total Output Error versus Ambient Temperature
8.0
6.0
4.0
ETOT (%)
ELIN (%)
Nonlinearity versus Ambient Temperature
-25
75
TA (°C)
0.4
-0.4
–50
50
2.0
0
-2.0
-4.0
-6.0
-8.0
–50
-25
0
25
50
75
100
125
150
TA (°C)
Typical Maximum Limit
Mean
Typical Minimum Limit
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
11
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
Characteristic Performance Data
Data taken using the ACS716-12CB
Accuracy Data
Electrical Offset Voltage versus Ambient Temperature
Sensitivity versus Ambient Temperature
50
40
30
Sens (mV/A)
VOE (mV)
20
10
0
-10
-20
-30
-40
-50
–50
-25
0
25
50
75
100
125
150
40.0
39.5
39.0
38.5
38.0
37.5
37.0
36.5
36.0
35.5
–50
-25
0
25
TA (°C)
100.75
0.2
100.50
0.1
100.25
ESYM (%)
0.3
0
-0.1
99.50
99.25
50
150
99.75
-0.3
25
125
100.00
-0.2
0
100
Symmetry versus Ambient Temperature
101.00
75
100
125
99.00
–50
150
-25
0
25
50
75
100
125
150
TA (°C)
TA (°C)
Total Output Error versus Ambient Temperature
8.0
6.0
4.0
ETOT (%)
ELIN (%)
Nonlinearity versus Ambient Temperature
-25
75
TA (°C)
0.4
-0.4
–50
50
2.0
0
-2.0
-4.0
-6.0
-8.0
–50
-25
0
25
50
75
100
125
150
TA (°C)
Typical Maximum Limit
Mean
Typical Minimum Limit
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
12
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
Characteristic Performance Data
Data taken using the ACS716-25CB
Accuracy Data
Electrical Offset Voltage versus Ambient Temperature
Sensitivity versus Ambient Temperature
20.5
50
40
20.0
30
Sens (mV/A)
VOE (mV)
20
10
0
-10
-20
-30
19.0
18.5
18.0
17.5
-40
-50
–50
19.5
-25
0
25
50
75
100
125
17.0
150
–50
-25
0
25
TA (°C)
100.75
0.2
100.50
0.1
100.25
ESYM (%)
0.3
0
-0.1
99.50
99.25
50
150
99.75
-0.3
25
125
100.00
-0.2
0
100
Symmetry versus Ambient Temperature
101.00
75
100
125
99.00
–50
150
-25
0
25
50
75
100
125
150
TA (°C)
TA (°C)
Total Output Error versus Ambient Temperature
8.0
6.0
4.0
ETOT (%)
ELIN (%)
Nonlinearity versus Ambient Temperature
-25
75
TA (°C)
0.4
-0.4
–50
50
2.0
0
-2.0
-4.0
-6.0
-8.0
–50
-25
0
25
50
75
100
125
150
TA (°C)
Typical Maximum Limit
Mean
Typical Minimum Limit
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
13
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
Setting Overcurrent Fault Switchpoint
Setting 12CB and 25CB Versions
The VOC needed for setting the overcurrent fault switchpoint can
be calculated as follows:
VOC = Sens × | IOC | ,
where VOC is in mV, Sens in mV/A, and IOC (overcurrent fault
switchpoint) in A.
| Ioc | is the overcurrent fault switchpoint for a bidirectional (AC)
current, which means a bidirectional sensor will have two symmetrical overcurrent fault switchpoints, +IOC and –IOC .
See the following graph for IOC and VOC ranges.
IOC versus VOC
(12CB and 25CB Versions)
IOC
0.4 VCC / Sens
Not Valid Range
Valid Range
0.25 VCC / Sens
0
0. 25 VCC
– 0.25 VCC / Sens
0. 4 VCC
VOC
– 0.4 VCC / Sens
Example: For ACS716KLATR-25CB-T, if required overcurrent fault switchpoint is 50 A, and VCC = 3.3 V, then the
required VOC can be calculated as follows:
VOC = Sens × IOC = 18.5 × 50 = 925 (mV)
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
14
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
Setting 6BB Versions
The VOC needed for setting the overcurrent fault switchpoint can
be calculated as follows:
VOC = 1.17 × Sens × | IOC | ,
where VOC is in mV, Sens in mV/A, and IOC (overcurrent fault
switchpoint) in A.
| Ioc | is the overcurrent fault switchpoint for a bidirectional (AC)
current, which means a bidirectional sensor will have two symmetrical overcurrent fault switchpoints, +IOC and –IOC .
See the following graph for IOC and VOC ranges.
IOC versus VOC
(6BB Versions)
IOC
0.4 VCC / (1.17 × Sens)
Not Valid Range
Valid Range
0.25 VCC / (1.17 × Sens)
0
0.25 VCC
– 0.25 VCC / (1.17 × Sens)
0.4 VCC
VOC
– 0.4 VCC / (1.17 × Sens)
Example: For ACS716KLATR-6BB-T, if required overcurrent fault switchpoint is 10 A, and VCC = 3.3 V, then the
required VOC can be calculated as follows:
VOC = 1.17 × Sens × IOC = 1.17 × 100 × 10 = 1170 (mV)
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
15
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
Functional Description (Latching Versions)
Overcurrent Fault Operation
The primary concern with high-speed fault detection is that noise
may cause false tripping. Various applications have or need to
be able to ignore certain faults that are due to switching noise or
other parasitic phenomena, which are application dependant. The
problem with simply trying to filter out this noise in the main
signal path is that in high-speed applications, with asymmetric
noise, the act of filtering introduces an error into the measurement. To get around this issue, and allow the user to prevent the
fault signal from being latched by noise, a circuit was designed to
¯T̄¯ pin voltage based on the value of the capacitor
slew the F̄¯Ā¯Ū¯L̄
from that pin to ground. Once the voltage on the pin falls below
2 V, as established by an internal reference, the fault output is
latched and pulled to ground quickly with an internal N-channel
MOSFET.
Fault Walkthrough
The following walkthrough references various sections and
attributes in the figure below. This figure shows different
fault set/reset scenarios and how they relate to the voltages on
the F̄¯Ā¯Ū¯L̄¯T̄¯ pin, FAULT_EN pin, and the internal Overcurrent
(OC) Fault node, which is invisible to the customer.
1.Because the device is enabled (FAULT_EN is high for a
minimum period of time, the Fault Enable Delay, tFED , 15 µs
¯L̄¯T̄¯
typical) and there is an OC fault condition, the device F̄¯Ā¯Ū
pin starts discharging.
¯ pin voltage reaches approximately 2 V, the
2.When the F̄¯Ā¯Ū¯L̄¯T̄
¯L̄¯T̄¯
fault is latched, and an internal NMOS device pulls the F̄¯Ā¯Ū
¯L̄¯T̄¯
pin voltage to approximately 0 V. The rate at which the F̄¯Ā¯Ū
pin slews downward (see [4] in the figure) is dependent on the
external capacitor, COC, on the F̄¯Ā¯Ū¯L̄¯T̄¯ pin.
¯L̄¯T̄¯
3.When the FAULT_EN pin is brought low, the F̄¯Ā¯Ū
pin starts resetting if no OC fault condition exists, and if
FAULT_EN is low for a time period greater than tOCH . The
VCC
FAULT
(Output)
2V
1
internal NMOS pull-down turns off and an internal PMOS pullup turns on (see [7] if the OC fault condition still exists).
4.The slope, and thus the delay to latch the fault is controlled by
¯L̄¯T̄¯ pin to ground. Durthe capacitor, COC, placed on the F̄¯Ā¯Ū
¯Ā¯Ū
¯L̄¯T̄¯ pin is between
ing this portion of the fault (when the F̄
VCC and 2 V), there is a 3 mA constant current sink, which
discharges COC. The length of the fault delay, t, is equal to:
COC ( VCC – 2 V )
(1)
3 mA
where VCC is the device power supply voltage in volts, t is in
seconds and COC is in Farads. This formula is valid for RPU
equal to or greater than 330 kΩ. For lower-value resistors,
the current flowing through the RPU resistor during a fault
event, IPU , will be larger. Therefore, the current discharging
the capacitor would be 3 mA – IPU and equation 1 may not be
valid.
¯Ū¯L̄¯T̄¯ pin did not reach the 2 V latch point before the
5.The F̄¯Ā
OC fault condition cleared. Because of this, the fixed 3 mA
current sink turns off, and the internal PMOS pull-up turns on
¯L̄¯T̄¯ pin.
to recharge COC through the F̄¯Ā¯Ū
t=
6.This curve shows VCC charging external capacitor COC
through the internal PMOS pull-up. The slope is determined
by COC.
7.When the FAULT_EN pin is brought low, if the fault condition
still exists, the latched F̄¯Ā¯Ū¯L̄¯T̄¯ pin will be pulled low by the
internal 3mA current source. When fault condition is removed
then the Fault pin charges as shown in step 6.
8.At this point there is a fault condition, and the part is enabled
¯Ū¯L̄¯T̄
¯ pin can charge to VCC. This shortens the
before the F̄¯Ā
user-set delay, so the fault is latched earlier. The new delay
time can be calculated by equation 1, after substituting the
¯L̄¯T̄¯ pin for VCC.
voltage seen on the F̄¯Ā¯Ū
1
tFED
4
6
1
6
4
8
4
5
2
4
2
6
2
7
0V
3
Time
FAULT_EN
(Input)
OC Fault
Condition
(Active High)
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
16
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
Functional Description (Non-Latching Versions)
Overcurrent Fault Operation
The primary concern with high-speed fault detection is that noise
may cause false tripping. Various applications have or need to
be able to ignore certain faults that are due to switching noise or
other parasitic phenomena, which are application dependant. The
problem with simply trying to filter out this noise in the main signal path is that in high-speed applications, with asymmetric noise,
the act of filtering introduces an error into the measurement.
To get around this issue, and allow the user to prevent the fault
signal from going low due to noise, a circuit was designed to slew
the F̄¯Ā¯Ū¯L̄¯T̄¯ pin voltage based on the value of the capacitor from
that pin to ground. Once the voltage on the pin falls below 2 V, as
established by an internal reference, the fault output is pulled to
ground quickly with an internal N-channel MOSFET.
Fault Walkthrough
The following walkthrough references various sections and
attributes in the figure below. This figure shows different
fault set/reset scenarios and how they relate to the voltages on
¯Ā¯Ū¯L̄¯T̄¯ pin, FAULT_EN pin, and the internal Overcurrent
the F̄
(OC) Fault node, which is invisible to the customer.
1.Because the device is enabled (FAULT_EN is high for a minimum period of time, the Fault Enable Delay, tFED , and there is
¯T̄¯ pin starts discharging.
an OC fault condition, the device F̄¯Ā¯Ū¯L̄
¯Ā¯Ū¯L̄¯T̄
¯ pin voltage reaches approximately 2 V, an
2.When the F̄
internal NMOS device pulls the F̄¯Ā¯Ū¯L̄¯T̄¯ pin voltage to approx¯L̄¯T̄¯ pin slews downward
imately 0 V. The rate at which the F̄¯Ā¯Ū
(see [4] in the figure) is dependent on the external capacitor,
¯T̄¯ pin.
COC, on the F̄¯Ā¯Ū¯L̄
3.When the FAULT_EN pin is brought low, the F̄¯Ā¯Ū¯L̄¯T̄¯ pin
starts resetting if FAULT_EN is low for a time period greater
VCC
FAULT
(Output)
2V
0V
1
than tOCH . The internal NMOS pull-down turns off and an
internal PMOS pull-up turns on.
4.The slope, and thus the delay to pull the fault low is controlled
¯L̄¯T̄¯ pin to ground.
by the capacitor, COC, placed on the F̄¯Ā¯Ū
¯Ā¯Ū
¯L̄¯T̄
¯ pin is
During this portion of the fault (when the F̄
between VCC and 2 V), there is a 3 mA constant current sink,
which discharges COC. The length of the fault delay, t, is equal
to:
COC ( VCC – 2 V )
(2)
3 mA
where VCC is the device power supply voltage in volts, t is in
seconds and COC is in Farads. This formula is valid for RPU
equal to or greater than 330 kΩ. For lower-value resistors,
the current flowing through the RPU resistor during a fault
event, IPU , will be larger. Therefore, the current discharging
the capacitor would be 3 mA – IPU and equation 1 may not be
valid.
¯Ū¯L̄¯T̄¯ pin did not reach the 2 V latch point before the
5.The F̄¯Ā
OC fault condition cleared. Because of this, the fixed 3 mA
current sink turns off, and the internal PMOS pull-up turns on
¯L̄¯T̄¯ pin.
to recharge COC through the F̄¯Ā¯Ū
t=
6.This curve shows VCC charging external capacitor COC
through the internal PMOS pull-up. The slope is determined
by COC.
7.At this point there is a fault condition, and the part is enabled
¯Ū¯L̄
¯T̄¯ pin can charge to VCC. This shortens the
before the F̄¯Ā
user-set delay, so the fault gets pulled low earlier. The new
delay time can be calculated by equation 1, after substituting
¯Ū¯L̄¯T̄
¯ pin for VCC.
the voltage seen on the F̄¯Ā
1
tFED
4
6
1
6
4
7
4
5
2
2
4
6
2
3
Time
FAULT_EN
(Input)
OC Fault
Condition
(Active High)
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
17
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
Chopper Stabilization Technique
Chopper stabilization is an innovative circuit technique that is
used to minimize the offset voltage of a Hall element and an associated on-chip amplifier. Allegro patented a chopper stabilization technique that nearly eliminates Hall IC output drift induced
by temperature or package stress effects. This offset reduction
technique is based on a signal modulation-demodulation process.
Modulation is used to separate the undesired DC offset signal
from the magnetically induced signal in the frequency domain.
Then, using a low-pass filter, the modulated DC offset is suppressed while the magnetically induced signal passes through
the filter. As a result of this chopper stabilization approach, the
output voltage from the Hall IC is desensitized to the effects
of temperature and mechanical stress. This technique produces
devices that have an extremely stable electrical offset voltage, are
immune to thermal stress, and have precise recoverability after
temperature cycling.
This technique is made possible through the use of a BiCMOS
process that allows the use of low-offset and low-noise amplifiers
in combination with high-density logic integration and sampleand-hold circuits.
Regulator
Clock/Logic
Hall Element
Amp
Sample and
Hold
ACS716
Low-Pass
Filter
Concept of Chopper Stabilization Technique
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
18
ACS716
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
Definitions of Accuracy Characteristics
Sensitivity (Sens). The change in sensor output in response to a
1 A change through the primary conductor. The sensitivity is the
product of the magnetic circuit sensitivity (G / A) and the linear
IC amplifier gain (mV/G). The linear IC amplifier gain is programmed at the factory to optimize the sensitivity (mV/A) for the
full-scale current of the device.
Noise (VNOISE). The product of the linear IC amplifier gain
(mV/G) and the noise floor for the Allegro Hall-effect linear
IC. The noise floor is derived from the thermal and shot noise
observed in Hall elements. Dividing the noise (mV) by the sensitivity (mV/A) provides the smallest current that the device is able
to resolve.
Linearity (ELIN). The degree to which the voltage output from
the sensor varies in direct proportion to the primary current
through its full-scale amplitude. Nonlinearity in the output can be
attributed to the saturation of the flux concentrator approaching
the full-scale current. The following equation is used to derive the
linearity:
{ [
100 1–
VIOUT_full-scale amperes – VIOUT(Q)
2 (VIOUT_1/2 full-scale amperes – VIOUT(Q) )
[{
Accuracy is divided into four areas:
• 0 A at 25°C. Accuracy of sensing zero current flow at 25°C,
without the effects of temperature.
• 0 A over Δ temperature. Accuracy of sensing zero current
flow including temperature effects.
• Full-scale current at 25°C. Accuracy of sensing the full-scale
current at 25°C, without the effects of temperature.
• Full-scale current over Δ temperature. Accuracy of sensing fullscale current flow including temperature effects.
Ratiometry. The ratiometric feature means that its 0 A output,
VIOUT(Q), (nominally equal to VCC/2) and sensitivity, Sens, are
proportional to its supply voltage, VCC . The following formula is
used to derive the ratiometric change in 0 A output voltage,
ΔVIOUT(Q)RAT (%).
100
VCC / 3.3 (V)

The ratiometric change in sensitivity, ΔSensRAT (%), is defined as:
where VIOUT_full-scale amperes = the output voltage (V) when the
sensed current approximates full-scale ±IP .
100
Symmetry (ESYM). The degree to which the absolute voltage
output from the sensor varies in proportion to either a positive
or negative full-scale primary current. The following formula is
used to derive symmetry:
100

VIOUT(Q)VCC / VIOUT(Q)3.3V

SensVCC / Sens3.3V

VCC / 3.3 (V)
Output Voltage versus Sensed Current
Accuracy at 0 A and at Full-Scale Current
Increasing VIOUT(V)
Accuracy
Over ∆Temp erature
VIOUT_+ full-scale amperes – VIOUT(Q)
 VIOUT(Q) – VIOUT_–full-scale amperes 
Accuracy
25°C Only
Quiescent output voltage (VIOUT(Q)). The output of the sensor
when the primary current is zero. For a unipolar supply voltage,
it nominally remains at 0.5×VCC. For example, in the case of a
bidirectional output device, VCC = 3.3 V translates into VIOUT(Q)
= 1.65 V. Variation in VIOUT(Q) can be attributed to the resolution
of the Allegro linear IC quiescent voltage trim and thermal drift.
Electrical offset voltage (VOE). The deviation of the device output from its ideal quiescent voltage due to nonmagnetic causes.
To convert this voltage to amperes, divide by the device sensitivity, Sens.
Accuracy (ETOT). The accuracy represents the maximum deviation of the actual output from its ideal value. This is also known
as the total ouput error. The accuracy is illustrated graphically in
the output voltage versus current chart at right. Note that error is
directly measured during final test at Allegro.
Average
VIOUT
Accuracy
Over ∆Temp erature
IP(min)
Accuracy
25°C Only
–IP (A)
+IP (A)
Full Scale
IP(max)
0A
Accuracy
25°C Only
Accuracy
Over ∆Temp erature
Decreasing VIOUT(V)
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
19
ACS716
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
Definitions of Dynamic Response Characteristics
I (%)
Propagation delay (tPROP). The time required for the sensor
output to reflect a change in the primary current signal. Propagation delay is attributed to inductive loading within the linear IC
package, as well as in the inductive loop formed by the primary
conductor geometry. Propagation delay can be considered as a
fixed-time offset and may be compensated.
Primary Current
90
Transducer Output
0
Propagation Time, tPROP
I (%)
Response time (tRESPONSE). The time interval between a) when
the primary current signal reaches 90% of its final value, and b)
when the sensor reaches 90% of its output corresponding to the
applied current.
Primary Current
90
Transducer Output
0
Response Time, tRESPONSE
Rise time (tr). The time interval between a) when the sensor
reaches 10% of its full-scale value, and b) when it reaches 90%
of its full-scale value. The rise time to a step response is used to
derive the bandwidth of the current sensor, in which ƒ(–3 dB) =
0.35 / tr. Both tr and tRESPONSE are detrimentally affected by eddy
current losses observed in the conductive IC ground plane.
t
I (%)
t
Primary Current
90
Transducer Output
10
0
Rise Time, tr
t
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
20
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
Package LA, 16-Pin SOICW
10.30 ±0.20
8°
0°
16
0.33
0.20
7.50 ±0.10
0.65
16
1.27
2.25
10.30 ±0.33
9.50
A
1.40 REF
1
2
1.27
0.40
Branded Face
16X
SEATING
PLANE
0.10 C
0.51
0.31
1.27 BSC
2
0.25 BSC
C
SEATING PLANE
GAUGE PLANE
C
PCB Layout Reference View
2.65 MAX
0.30
0.10
For Reference Only; not for tooling use (reference MS-013AA)
Dimensions in millimeters
Dimensions exclusive of mold flash, gate burrs, and dambar protrusions
Exact case and lead configuration at supplier discretion within limits shown
A Terminal #1 mark area
B Branding scale and appearance at supplier discretion
C
1
Reference land pattern layout (reference IPC7351
SOIC127P600X175-8M); all pads a minimum of 0.20 mm from all
adjacent pads; adjust as necessary to meet application process
requirements and PCB layout tolerances
NNNNNNNNNNN
TTT-TTT
LLLLLLLLL
1
B Standard Branding Reference View
N = Device part number
T = Temperature range, package - amperage
L = Lot number
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
21
120 kHz Bandwidth, High-Voltage Isolation
Current Sensor with Integrated Overcurrent Detection
ACS716
Revision History
Revision
Revision Date
Description of Revision
3
January 15, 2013
Update IR , IP , add non-latching versions, update
to current terminology
4
August 19, 2015
Added certificate number under UL stamp on
page 1; updated Isolation Characteristics table.
Copyright ©2011-2015, Allegro MicroSystems, LLC
Allegro MicroSystems, LLC reserves the right to make, from time to time, such departures from the detail specifications as may be required to
permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the user is cautioned to verify that
the information being relied upon is current.
Allegro’s products are not to be used in life support devices or systems, if a failure of an Allegro product can reasonably be expected to cause the
failure of that life support device or system, or to affect the safety or effectiveness of that device or system.
The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its
use; nor for any infringement of patents or other rights of third parties which may result from its use.
For the latest version of this document, visit our website:
www.allegromicro.com
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
22