A5191HRTNGEVB A5191HRTNGEVB Evaluation Board User's Manual http://onsemi.com EVAL BOARD USER’S MANUAL Introduction Features • Single−chip, Half−duplex 1200 Bits per Second FSK The A5191HRTNGEVB evaluation board includes all external components needed for operating the A5191HRT IC and demonstrates the small PCB surface area such an implementation requires. The EVB allows easy design of HART® implementations using A5191HRT. • • • • • • • Overview The A5191HRT is a single−chip, CMOS modem for use in highway addressable remote transducer (HART) field instruments and masters. The modem and a few external passive components provide all of the functions needed to satisfy HART physical layer requirements including modulation, demodulation, receive filtering, carrier detect, and transmit−signal shaping. The A5191HRT uses phase continuous frequency shift keying (FSK) at 1200 bits per second. To conserve power the receive circuits are disabled during transmit operations and vice versa. This provides the half−duplex operation used in HART communications. • • • Modem Bell 202 Shift Frequencies of 1200 Hz and 2200 Hz 3.0 V − 5.5 V Power Supply Transmit−signal Wave Shaping Receive Band−pass Filter Low Power: Optimal for Intrinsically Safe Applications Compatible with 3.3 V or 5 V Microcontroller Internal Oscillator Requires 460.8 kHz Crystal or Ceramic Resonator Meets HART Physical Layer Requirements Industrial Temperature Range of −40°C to +85°C Available in 28−pin PLCC, 32−pin QFN and 32−pin LQFP Packages Applications • HART Multiplexers • HART Modem Interfaces • 4 – 20 mA Loop Powered Transmitters Figure 1. A5191HRTNGEVB Evaluation Board © Semiconductor Components Industries, LLC, 2013 November, 2013 − Rev. 4 1 Publication Order Number: EVBUM2130/D A5191HRTNGEVB ELECTRICAL CHARACTERISTICS Table 1. ELECTRICAL CHARACTERISTICS OF THE A5191HRTNGEVB BOARD Value Symbol VDD Parameter / Condition Supply voltage Min Typ Max Unit 2.78 3 6.00 V CURRENT CONSUMPTION IDD VDD = 2.78V, idle 417 mA IDD VDD = 3.00 V, idle 420 mA IDD VDD = 6.00V, idle 780 mA IDD External clock, VDD = 3.00 V, idle 350 mA TRANSMITTED FREQUENCY fM Mark “1” 1197 Hz fS Space “0” 2194 Hz VTxA Amplitude Transmit Output 500 mVpp VCD Carrier Detect Level 110 mVpp AREF 1.212 V CDREF 1.128 V LEVELS REFERENCE VOLTAGES VAREF VCDREF A5191HRT DESCRIPTION When the device is transmitting data, the receive module is shut down and vice versa to conserve power. With simple power−saving maneuvers, the IC can be made to operate with a current consumption of as little as 250 mA. For more information related to this subject see the application note AND9030 “A5191HRT Design for Low−Power Environments”. The A5191HRT modem is a single−chip CMOS modem for use in HART field instruments and masters. It includes on−chip oscillator and a modulator and demodulator module communicating with a UART without internal buffer. The A5191HRT requires some external filter components and a 460.8 kHz clock source. This clock source can either be the interface oscillator by using a crystal or ceramic resonator, or an external clock signal. TEST AND MEASUREMENT TOOLS Listed below are the tools used to acquire the values presented in this Evaluation Board User’s Manual. • Oscilloscope Tektronix DPO4034 350 MHz • Signal Generator Agilent 33120A • Network Analyzer AP Instruments 300 http://onsemi.com 2 A5191HRTNGEVB A5191HRTNGEVB DESCRIPTION Schematic Diagram Figure 2. Schematic of A5191HRTNEVB http://onsemi.com 3 A5191HRTNGEVB BOM List Table 2. A5191HRTNEVB BILL OF MATERIALS Quantity Reference Value; Size 4 C1, C2, C4, C6 100 nF, 0603 3 C3, C5, C7 220 pF, 0603 2 C8, C9 1 nF, 0603 2 C10, C11 470 pF, 0603 Manufacturer & Comments 3 FB1, FB2, FB3 600Z, 0805 3 IDC1, IDC2, IDC3 0.1” header, 10 pin 1 J1 Barrel connector Not populated 1 J2 SMB connector Not populated 4 R1, R2, R6, R21 200k, 0603 1 R3 0R, 0603 2 R4, R11 14k7, 0603 2 R7, R14 499k, 0603 3 R8, R16, R17 215k, 0603 1 R12 1k, 0603 1 R10 422k, 0603 1 R13 3M, 0603 1 R15 787k, 0603 1 R18 24k, 0603 1 R20 DNP, 0603 Not populated 1 U1 CAT808NTDI−27GT3 ON Semiconductor 1 U2 A5191HRT ON Semiconductor 1 U3 TLV431ASNT1G ON Semiconductor 1 Y1 460.8 kHz ECS Crystal ZTBF−460.8−E General Overview The A5191HRTNGEVB evaluation board demonstrates the external components required for the operation of the IC. We will cover the different sections below as well as possible alternatives. A drawing of the board where the different sections are indicated is shown below. Figure 3. Board Drawing With Indication of Different Sections http://onsemi.com 4 A5191HRTNGEVB Power Supply and References Power Supply Figure 4. Supply Voltage and Power on Reset Current consumption of the module is very limited, making it ideal to be battery or loop−powered. Measurements of the power consumption of the module are listed in Table 3. The A5191HRTNGEVB is designed for a nominal voltage of 3 V. However, A5191HRT can be operated up to 6 V. For optimal functioning of the board, the values of several resistors should be changed for operation at voltages higher than 3 V. See the sections on reference voltages and bias for more information on this. Table 3. MODULE CURRENT CONSUMPTION Symbol Condition Current Consumption IDD VDD = 2.78 V, Transmit 428 mA IDD VDD = 2.78 V, Receive 417 mA IDD VDD = 3 V, Transmit 443 mA IDD VDD = 3 V, Receive 419 mA IDD VDD = 6 V, Transmit 837 mA IDD VDD = 6 V, Receive 781 mA IDD VDD = 3 V, Transmit, Ext. Osc. 362 mA IDD VDD = 3 V, Receive, Ext. Osc. 350 mA The voltage supervisor will keep the RESETB pin low until its threshold value is reached (2.7 V on the A5191HRTNGEVB). This ensures that some time has passed after the supply voltage reaches the turn−on voltage level of 2.5 V. The RESETB and VDD pin signals during startup are shown in Figure 5. The measured start−up delay is 2.6 ms. The module will use less power when clock signal is applied externally, as this allows the modem to shut down the oscillator circuit. As is to be expected, a higher supply voltage increases current consumption. It is advised to use a voltage supervisor such as CAT808 to prevent the modem to begin operation when the supply voltage is not yet reliable. This will guarantee correct operation of the digital circuitry. http://onsemi.com 5 A5191HRTNGEVB Figure 5. Power and RESETB Waveform During Startup, Showing 2.63 ms Startup Delay compared against the output voltage, and the shunt transistor base is adjusted until it sinks enough current to drop the output to 1.24 V. A simple low pass filter formed by R12 and C11 is added to increase reference stability. A slight voltage drop is observed over this filter caused by loading of the reference voltage. However, the voltage drop and the influence on the operation of the IC is minimal. Measurements show a voltage drop of 22 mV over R12, indicating a current of 22 mA. Of this current ca. 5 mA is consumed by the CDREF resistor division. The rest (ca. 17 mA) is used internally by the IC through the AREF pin. Current consumption through the CDREF pin is negligible. The CDREF reference voltage sets the threshold for the carrier detect comparator. As the received signal is biased at AREF, the difference between CDREF and AREF will determine the minimum amplitude needed for the carrier detect comparator to flip. A (AREF−CDREF) of 80 mV corresponds to signal of approximately 100 mV peak−to−peak at the input of the receive filter. The CDREF reference voltage on the A5191HRTNGEVB is generated by a resistor division of the AREF reference. This will create an extra load on the low pass filter of AREF. However, the drop on the resistor of the low pass can be considered negligible. An external resistor is required to set the bias current. The voltage over the bias resistor is regulated to AREF, so that the resistor determines a bias current. This bias current C1, C2 and C6 are 100 nF ceramic decoupling capacitors located directly adjacent to each power pin. For analog power pins, an additional large−value ceramic capacitor may be needed in addition to the 100 nF decoupling capacitor when the application is intended for high−noise environments. For loop powered devices, additional decoupling with a large value capacitor is advised to prevent digital noise from being transmitted on the current loop. The ferrite beads FB1, FB2 and FB3 in series with power supply lines help to reduce EMI. Reference voltages and comparator bias A5191HRT needs an external analog reference voltage for the receiver or demodulator (RX) comparator and carrier detect (CD). The AREF reference voltage sets the trip point of the demodulation operational amplifier of the 5191HRT. The AREF reference voltage is also used in setting the DC operating point of the received signal after it has passed through the band−pass receive filter. The ideal value for the AREF reference voltage depends on the voltage supply, and is chosen roughly half−way the operating range of the operational amplifiers. This ensures the range of the operational amplifier is maximized. For operation at 3 V, a 1.24 V reference voltage is recommended. For operation at 5 V, a 2.5 V reference voltage is recommended. For A5191HRTNGEVB, the TLV431 shunt regulator is used with an internal reference of 1.24 V. This reference is http://onsemi.com 6 A5191HRTNGEVB controls the operating parameters of the internal operational amplifiers and comparators and should be set to approximately 2.5 mA. A bias resistor of 499 kW is used on the A5191HRTNGEVB. For low cost solutions, a 470 kW is acceptable with minimal effect on operation. Table 4. REFERENCE VOLTAGES Description Value AREF reference voltage 1.212 V CDREF reference voltage 1.128 V Current through R12 22 mA Figure 6. Reference Voltages Schematic Clock Generation to shut down the oscillator circuit. A typical current consumption witnessed by utilizing an external oscillator is 70 − 100 mA less. However, care must be taken that this external signal has the required accuracy (1%). Duty cycle of the clock signal is specified between 40% and 60%. No errors were observed during testing in operation between 20% and 80% duty cycle. However, operation on such very small or very large duty cycle is not recommended, due to the possibility of timing errors that may occur under specific circumstances (including, but not limited to, temperature variations). A5191HRT is operated on a 460.8 kHz clock signal. The A5191HRTNGEVB has two options for providing this clock signal. The first method is by using a ceramic resonator or a crystal. The standard populated option is a ECS Crystal ZTBF−460.8−E ceramic resonator, loaded with two 220 pF capacitors. Alternatively, a clock signal can be provided externally when R3 is removed and C3 is replaced by a resistor of 0 W. This signal can be provided by a microcontroller or any other external oscillator circuit. The module uses less power when clock signal is applied externally, as this allows the modem a.) Resonator Option b.) External Clock Option Figure 7. Clock Generation Circuit http://onsemi.com 7 A5191HRTNGEVB Microcontroller Interface IDC1 VCC R2 VCC R23 IDC1 2 9 RTS 7 TxD 5 RxD 3 CD 1 22 23 25 26 RESET PC20110513.4 Figure 8. Microcontroller Interface Table 5. MICROCONTROLLER INTERFACE Pin Number Signal Type 1 RST Open drain 3 CD Output 5 RxD Input 7 TxD Output 9 RTSB Input 2, 10 VDD Power 4, 6, 8 GND Power Description Reset signal from the voltage supervisor, open drain with pull−up Carrier Detect Receive from microcontroller Transmit towards microcontroller Request to send 3 V nominal skew between transmitting and receiving HART devices. If the transmit time base is at 99% of nominal and the receive time base in another device is at 101% of nominal, the receive data (at the receiving UART) will be skewed by roughly 21% of one bit time at the end of each 11−bit byte. This is shown in Figure 9. The skew time is measured from the initial falling edge of the start bit to the center of the 11th bit cell. This 21% skew by itself is a relatively good result. However, there is another error source for bit boundary jitter. The Phase Lock Loop demodulator in the A5191HRT produces jitter in the receive data that can be as large as 12% of a bit time. Therefore, a bit boundary can be shifted by as much as 24% of a bit time relative to its ideal location based on the start−bit transition. (The start−bit transition and a later transition can be shifted in opposite directions for a total of 24%.) The clock skew and jitter added together is 45%, which is the amount that a bit boundary could be shifted from its expected position. UARTs that sample at mid−bit will not be affected. However, there are UARTs that take multiple samples during each bit to try to improve on error performance. These UARTs may not be satisfactory, depending on how close the samples are to each other, and how samples are interpreted. A UART that takes a majority vote of three samples is acceptable. The interface towards a microcontroller is provided in IDC1. This interface can also be used to supply power to the module. The nominal supply voltage for the module is 3 V. For more information see the section on power supply and references. The RESETB line to the modem is an open drain signal. A pull−up resistor of 200 kW is provided on the board, and should not be duplicated on the microcontroller side. The reset signal is generated on the board, and could be used as reset signal for other IC such as the microcontroller. The CD signal rises when a HART signal of ca. 100 mVpp is detected on the current loop. See the section on reference voltages for more information on these threshold level settings. When no signal, or a signal of limited amplitude is present, the CD line is pulled down to 0 V. The RxD, TxD, and RTSB signals implement a standard UART interface at 1200 baud with start bit 8 data bits, parity bit and stop bit (11−bit frame). The RTSB signal disconnects the transmitter circuit when pulled high, and should be held low before any data is transmitted. Data frames are not buffered by the modem. Instead, data is transmitted bit by bit. Care should be taken to avoid clock skew in the receiving UART. If the same time base is used for both the modem and the UART, a 1% accurate time base may not be sufficient. The problem is a combination of receive data jitter and clock http://onsemi.com 8 A5191HRTNGEVB Figure 9. Clock Skew Even if your own time base is perfect, you still must plan on a possible 35% shift in a bit boundary, since you don’t have control over time bases in other HART devices. can only drive impedances higher than 30 kW, and as a consequence may need to be amplified to drive low impedances. For a given implementation of a master or slave, it may be required to remove C4 and replace it with a 0 W resistor to allow the decoupling to occur elsewhere in the master implementation. The nominal frequency of the output is 1196.9 Hz for “mark” and 2194.3 Hz for “space”. These frequencies are dependent on the accuracy of the A5191 clock. Transmitter The TxA modem pin is decoupled through a 100 nF capacitor to pin 7 of IDC2. For certain applications, it might be required to remove this capacitor and replace it by a 0 W resistor. The output on this pin is a 500 mVpp signal trapezoid waveform shown in Figures 10 and 11. This pin Figure 10. Output Waveform (Mark) http://onsemi.com 9 A5191HRTNGEVB Figure 11. Output Waveform (Space) Receiver this filter can be implemented using E12 value resistors with minimal changes to the filter characteristic. This implementation will have a slightly reduced gain in the pass band. The receive band pass filter is implemented on the A5191HRTNGEVB. The values are listed in Table 6 and the filter schematic is displayed in Figure 12. For cost purposes, Figure 12. Receive Filter http://onsemi.com 10 A5191HRTNGEVB Table 6. RECEIVE FILTER COMPONENT VALUES Reference Value E96 Value E12 (Low−cost) R16 215 kW 1% 220 kW 1% R17 215 kW 1% 220 kW 1% R14 499 kW 1% 470 kW 1% R15 787 kW 1% 680 kW 1% R10 422 kW 1% 470 kW 1% R8 215 kW 1% 220 kW 1% R13 3 MW 1% 3.3 MW 1% C10 470 pF 5% 470 pF 5% C8 1 nF 5% 1 nF 5% C9 1 nF 5% 1 nF 5% C7 220 pF 5% 220 pF 5% Figure 13. Filter Characteristic (First Stage = black, Total = Blue) a bigger variation in the characteristic is observed. Figures 14a and 14b show a monte carlo analysis for resistors of 1% and 10%. It is advised to use resistors of at least 1% accuracy. In Figure 13 the simulated characteristic of the entire filter is shown, in both variations, for the first stage (black) and total filter (blue). The normal and low−cost variations are superimposed, showing that the variations are minimal. However, when the tolerance on the values is also loosened, http://onsemi.com 11 A5191HRTNGEVB Figure 14. Monte Carlo Analysis of the First Filter Stage for 10% (above) and 1% (below) Accuracy too high in frequency to have an influence on the phase of HART signals. Figure 16 shows the group delay of the total filter. It is important that the difference in group delay between the mark and space is minimal, so that the output of the filter still has coherence between both signals. The plot of Figure 16 shows that the difference is indeed minimal. In Figure 15 the measured filter characteristic of both variations are shown next to a simulated result. These characteristics are only of the first stage of the filter as the output of the second stage is not accessible. We notice an additional pole showing up at high frequencies. This only improves the filter by rejecting high frequency noise, and is Figure 15. Measured and Simulated Filter Characteristic of the First Filter Stage http://onsemi.com 12 A5191HRTNGEVB Figure 16. Group Delay of the Total Filter the operational amplifier, and the removal of R14. The filter is a variation on the Sallen−Key topology with three poles. The AREF voltage serves here as a biasing voltage, but can for ac frequencies be regarded as ground. For a complete analysis of this filter type, see the Appendix on Page 17. First Stage The first stage of the filter is implemented as a modified third−order high pass active filter. Consider the circuit shown in Figure 17. This resembles the implemented filter except for the coupling capacitor on Figure 17. Simplified First Filter Stage Schematic http://onsemi.com 13 A5191HRTNGEVB Introducing R14 does not introduce another pole or zero but changes the denominator of the transfer function, and thus the location of the poles. The final transfer function of the first filter stage is thus a fourth order filter of the form: The transfer function of this type of filter is: Taking into account the compensation capacitance present on the operational amplifier between input and output introduces another high frequency pole and zero pair. The zero of which can easily be determined to be: The poles of this transfer function are located at: p1, p2 = 195 Hz p3 = 1.220 kHz p4 = 22 kHz The input impedance of this filter stage is higher than 89 kW at frequencies below 50 kHz. Determining the exact location of the extra pole requires extra calculation. Indeed, the location of the other poles will also be shifted by this extra circuit element. Figure 18. Input Impedance of the First Filter Stage Second Stage The second stage of the receive filter is a simple band pass filter consisting of cascaded passive low− and high−pass filter. Again the AREF voltage can be considered ground for AC frequencies, and serves only to bias the output of the filter around AREF. It can be shown that this stage has the following transfer function: AREF R2 R1 This stage has two poles that can easily be calculated: p1 = 36 Hz p2 = 3316 Hz C2 Stage 1 Vout C1 KVDE20110406.4 Figure 19. Second Filter Stage Schematic http://onsemi.com 14 A5191HRTNGEVB Figure 20. Characteristic of the Second Stage of the Filter APPLICATION IDEAS The A5191HRT takes care of the HART modulation. This HART signal must then be superimposed on a 4−20mA current loop. Below are some possible implementations of both a master and slave transmitter. Next, the values of R4 and R5 are chosen depending on the most significant bit of the DAC. When the DAC is not a switching topology, we can now choose R1 and C1. We have: Slave implementation A simple slave implementation is shown in Figure 21. The analog loop current is set by a DAC from the microcontroller, while HART signals are added in from the A5191HRT. The DAC can be PWM or sigma−delta topology. To explain the operation of this circuit, let us first look at an example where the DAC is not of a switching topology. In this case, R2 and R3 can be 0 W, and C2, C3 and C5 can be left out. As one end of R6 is tied to local ground, it can easily be seen that the voltage at the negative loop terminal is negative with respect to the local ground. Resistors R4 and R5 are then chosen so that in steady state their common terminal is a virtual ground point in the absence of HART signals, since the negative terminal of the amplifier is also connected to ground. A similar principle applies when HART signals are applied. So both amplifier inputs are regulated to ground. A compensation capacitor C4 may be required depending on the operational amplifier used. To avoid offset generated by bias current in the operational amp, R3 should be dimensioned to approach the impedance seen by the positive terminal. The amplifier will then determine the current flowing through the loop by changing the base of a transistor in emitter feedback configuration. The value for R7 is determined by the output range Vo,max of the amplifier used: Where: In practice, C1 is chosen sufficiently small so that Z [ R1. For a PWM or sigma−delta output DAC, the circuit gets a bit more complicated, as we need to filter away high frequency DAC components, but leave HART signals intact. If the bandwidth of the DAC is larger than 2.2 kHz, adding C3 introduces a low−pass filter to the loop that will remove most of the switching noise. Where Rp is the parallel circuit of R4, R5 and R1. If the bandwidth of the DAC is close to the HART frequencies, an alternate high−frequency feedback path must be introduced so that HART signals are not removed by the low pass filter of the DAC. The exact calculation of component values in this case is more complicated. However, it is based on a similar principle, but now with two summing junctions, for low−frequency and high−frequency signals separated. Resistor R3 may be needed to compensate for amplifier bias current. It is chosen so that its resistance is similar to resistance seen on the positive terminal. Depending on the amplifier used, it may also be required to provide a compensation capacitance C4. It is often recommended to take a value as large as possible, so that noise effects are minimal. Typically the value of R6 is chosen equal to R7. The voltage over R6 and R7 combined should however be less than 12 V when the current setting is 20 mA. http://onsemi.com 15 A5191HRTNGEVB Figure 21. Sample Slave Implementation Master Implementation operational amplifier is required. Depending on the sense resistor used, some gain or attenuation may be required to get a 1 mA peak−to−peak HART output signal. This can be accomplished by the resistors R3 and R4. For a typical sense resistor of 500 W, a unity gain suffices and a unity gain operational amplifier configuration can be used instead. The amplifier however has a low impedance output, which cannot be paralleled with the sense resistor, as this would cause problems when the slave is transmitting. This problem is solved by adding a series switch (such as MC74VHC1G66DTT1G), controlled by the RTS signal. For a normally open switch, the nRTS signal as applied to the A5191 must be inverted first. To reduce power usage, the operational amplifier can be disabled when the transmitter is turned off. This is both done by inserting PNP transistor Q1on the VDD connection of the amplifier. To couple the signal into the current loop, a single capacitor was used. For other coupling techniques see application note AND8346/D. An example of a possible master implementation is shown in Figure 22. To use this schematic, the coupling capacitor C4 on the A5191HRTNGEVB will need to be replaced by a 0 W resistor, or new biasing must be provided. The current loop master has a sense resistor over which the current flowing through the loop can be measured. The value of this resistor varies depending on the sensitivity required and range of the ADC. A HART Master can have a sense resistor ranging from 230 W to 600 W. Increasing the sense resistor will result in higher amplitude HART signal received, but will also reduce the voltage available on the slave side. Furthermore, if you wish to sense the analog transmitted signal, the MSB of your DAC may limit the resistor size. If this limitation is too stringent, the sense resistor can be split in two resistors, as shown in the figure, effectively creating a resistor divider. To transmit a HART signal, the TxA signal will need to be amplified, as the A5191HRT transmit circuit can only drive high impedance circuits (>30 kW). An additional http://onsemi.com 16 A5191HRTNGEVB 3V nRTS R1 Q1 R7 AREF Loop + R2 U1 C2 OPA U2 R5 C1 TxA ADC R3 R4 R6 Loop − Figure 22. Sample Master Implementation APPENDIX Calculation of a three Pole Sallen−Key High Pass Filter The first stage of the receive filter uses a three pole active high pass filter with a topology similar to the one shown in Figure 17. We will derive the transfer function of this filter below. We will denote the gain configured with RA and RB as K. Resistors R3A and R3B serve only to bias the amplifier input in DC, and can for the rest of the calculations be considered parallel and replaced by one resistor: Using Kirkhof’s current law, we get in the three nodes of the filter: (eq. 1) (eq. 2) (eq. 3) Solving Equations 1 and 3 for V1 resp. V2 we find: (eq. 4) (eq. 5) For Equation 2 we find: (eq. 6) Or, with the substitution: http://onsemi.com 17 A5191HRTNGEVB Equation 6 simplifies to: (eq. 7) Substituting V1 and V2 in Equation 7 using Equations 4 and 5, and simplifying we find the transfer function: Where: Adding the compensation capacitor on the operational amplifier results in the following transformation on the transfer function: Where: Since K is present in the numerator of the transfer function, the zero of this factor will be present in the transformed transfer function. The denominator of the transformed transfer function is a forth order function with the following coefficients. The transfer function now has the following form: Where: http://onsemi.com 18 A5191HRTNGEVB Adding a series resistor to the capacitor results in the following transformation: Since C3 is not present in the numerator or in the highest−order coefficient, no extra poles or zeros will be introduced by this transformation. The form of the transfer function hence remains the same. The transformed coefficients are: http://onsemi.com 19 A5191HRTNGEVB EVALUATION BOARD LAYOUT Figure 23. Top Layer Layout Figure 24. Bottom Layer Layout HART is a registered trademark of the HART Communication Foundation of Austin, Texas, USA. Any time that the term ‘HART’ is used in this document or in any document referenced by this document, that term implies the registered trademark. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 20 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative EVBUM2130/D